Search Documents

By Y. J. Wang

The use of controlled recirculation began in the early 1930s. Although this method has been applied in many mines since then, a generalized comprehensive network analysis is still lacking. This paper presents a unique approach in which the ventilation network with a controlled district recirculation is divided into two subsystems: a main subsystem and a recirculation subsystem. The subsystems are analyzed individually, and the results and their relationships are then integrated into discussions of the total ventilation system. The analysis of the recirculation subsystem is facilitated by introducing a nondimensional parameter (A), which represents the ratio of the air quantity for the working face to that for the subsystem. As a result, far and regulator pressures and air power for various recirculation arrangements can be effectively expressed as a function of and the subsystem air quantity. Numerical examples are included.

Jan 1, 1997

By Timothy G. Shuttleworth

In the late1970s, mineral processing plants producing copper sulfide concentrates and oxide leaching feedstocks went online with operating tonnages that exceeded traditional installations. This created a need for larger capacity belt conveyors and apron feeders. Apron feeders are slow moving, heavily loaded conveyors that feed a deep bed of ore from a bulk holding location (a bunker) as a controlled stream, often into a large capacity crusher. Apron feeders use sprockets and caterpillars, while belt feeders use rubber belts with motorized head pulleys to convey the material. The damaging of belts and clogging of transfer points from tramp iron required larger magnetic separators and the removal of tramp metal cannot prevent these serious problems. Corrective action at this location is important for two reasons: Removing tramp iron early in the ore stream protects downstream equipment from potential costly damage. Installing apron feeder magnets before the primary large capacity crusher means that secondary and tertiary crushing steps (made up of multiple parallel units) operate more efficiently, since tramp metal is removed at the onset.

Jan 1, 2011

By Michael Day, Paul Kos, Scott Brinton

A hydrogeologic characterization and impact analysis was performed for a proposed quarry at the Hitch Rack Ranch located in the Little Turkey Creek watershed southwest of Colorado Springs, Colorado. Continuous multiple channel tubing, nested piezometers, stream flow measurements, and mapping of known seeps were used to define the three-dimensional potentiometric distribution and areas of groundwater recharge and discharge. Water balance considerations, mass balance calculations, and potentiometric response to earth tides and barometric fluctuations confirmed that the granite fracture system in the ridge area of the proposed quarry has an extremely low bulk hydraulic conductivity resulting in minimal groundwater discharge to sustain the baseflow of Little Turkey Creek. The Little Turkey Creek valley forms the major conduit for groundwater flow exiting from the upper part of watershed underlain by granite. This conclusion has significant implications with respect to mine planning to minimize projected impacts to the hydrologic system and preserve this recharge component to downgradient Denver Basin sedimentary deposits.

By P. Conrad

Experience has shown that, since the passage of the Surface Mining Control and Reclamation Act, over-compaction of spoil during the reclamation process has severely limited tree growth on reclaimed land. Researchers at the University of Kentucky have conducted a ten-year investigation at a surface mine in eastern Kentucky that monitored the changes in selected spoil physical characteristics for various reclamation and compaction alleviation methods. More specifically, research plots were developed for reforestation that employed three different levels of compaction and two different methods of ripping for overly compacted spoil. Each year measurements were made in the field of dry bulk density, using a nuclear density gage, and maximum penetration depth, using a recording cone penetrometer. In addition to good correlation between tree growth and selected spoil characteristics, the data demonstrated a gradual convergence of the measured spoil characteristic data over the study period.

Jan 1, 2008

By Russell. A. Smith

This paper describes some recent work on the identification and development of new chemical reagents aimed at improving the industrial processing of phosphate ores by froth flotation. In particular, three chemical product families which will be discussed appear to offer enhanced flexibility by: 1) utilizing a small amount of a silica control reagent which can significantly reduce the amount of anionic (carboxylic) collector required for a given P2O5 recovery level; 2) utilizing a new anionic collector family which offers high P2O5 recovery and selectivity versus standard carboxylic collectors; and 3) utilizing another new anionic collector family which has, in some tests, allowed for selective removal of dolomite from apatite. Examples and use characteristics of each of these new chemical ideas will be presented.

Jan 1, 1993

By W. R. Bull

This paper examines water-only cyclone performance for the cleaning of fine coal, and the effects of changes in feed flow rate, feed pulp density, and vortex finder diameter. A model is presented for performance simulation which can be used to predict products obtained based on feed washability data.

Jan 1, 1987

By Robert S. Setren, Jeffrey L. Ambs

The disposable diesel exhaust filter (DDEF) system developed by the U.S. Bureau of Mines and Industry cooperators for heavy-duty permissible, diesel-powered haulage vehicles, effectively reduces in-mine diesel particulate matter concentrations up to 95%. However, there are concerns about the hazards that exist when the filter is used in situations for which it was not designed. This work investigates the exhaust gas temperature limits to which the filter elements can be exposed without posing a safety or health hazard, such as 6re or off-gassing toxic compounds. A filter approved by the Mine Safety and Health administration and after-market filters were evaluated under varying engine exhaust conditions to determine if after-market filters pose an unacceptable hazard when used in a DDEF system. Filters were laboratory tested at engine exhaust temperatures ranging from 77°C to 290°C. Of the seven filter types tested, six appeared suitable for use on water scrubber-based cooling systems and two appeared suitable for use on dry heat exchanger type exhaust cooling systems with exhaust temperatures up to 150°C. Any filter elements used as exhaust filters on permissible diesel machines must be approved by MSHA for that application. Mine operators who wish to use an after-market filter element should request an MSHA field modification. MSHA will work with the mine and filter manufacturer to ensure its use in this exhaust system application does not pose a health or safety hazard.

Jan 1, 1995

By Randy Ynchausti

ERIC GUTIERREZ, Knowledgescape: Our next speaker is Randy Ynchausti. He's the director of development, Knowledgescape systems division, of EIMCO Process Equip- ment Company. The title of Randy's talk is "An Expert Control System for Phosphate Beneficiation." RANDY YNCHAUSTI: System integration. How does the systems integrator survive when caught between plant engineers, plant management, and third-party engineering firms, and stay within the budget of the corporate goals? I'm not sure that anyone knows how to do all of that on one project. Results are critical when we talk about how systems integrators work with operating people, how the operating people want systems integrators to work with them, and how both groups work together so that at the end of a project, you have been provided with solutions that meet your needs and solve your problems at a fair price. How does the integrator's role change when working with different types of professionals, such as plant managers, plant engineers, engineering firms, or other system integrators? Finally, what is the dynamics of people working with machines and providing services and solving needs? The average number of employees per pound of copper processed has decreased significantly during the past 15 years. I would dare to generalize and say that the average number of employees per whatever unit of measure we have in whatever industry we work in has decreased over the last 15 years. From a system integrator's perspective, there are some clients who lack a bit of internal expertise as corporate downsizing occurs, and that's one reason why we go out to system integrators or third-party vendors and buy things from them to solve our problems. Downsizing really amounts to savings, but more than that, I think Brian expressed this and I agree with him, it also amounts to a cost. Unfortunately, most of us count the savings and none of us count the cost in that approach. It's easy to count the savings, which is one reason why we count it so quickly. Maybe that also accounts for why we set our pencils down so quickly after we get that dollar value. Maybe we should pick that pencil up every once in awhile and refigure the expense, the cost to us, and determine what we're going to pay during the next year or two or three in losing that expense, or that staff. A broad experience base accumulated over projects at various plants helps system integrators to provide services to clients. This experience enables the system integrator to

Jan 1, 1998

By Z. T. Bieniawski

After many significant advances in mining, including development of sophisticated methods for strata characterization and numerical modeling analyses, the engineering design process in mining strata control is as primitive as it was two decades ago. Yet, major advances in design methodologies have occurred in other branches of engineering. Is creative design in mining a myth only? Are we deluding ourselves when we talk about innovative mining design of today? Did you know that most design experts are often unaware of their own decision-making processes? This paper explores the methodology of creative engineering design as a new recognized discipline.

Jan 1, 1987

By C. N. Greene

I am sure it is obvious to all of you that a complete program of casualty and property insurance is as necessary for any tunneling contractor as it is for anyone else involved in trade in the United States today. Going beyond those general undefined terms, there are many areas that need specific attention, particularly for contractors, regardless of size. WORKERS' COMPENSATION Workers' Compensation is mandatory in all states and the District of Columbia. In most of the states, private insurance provides this coverage. In a few states, the state operates Workers' Compensation funds, some of which are competitive with the private sector and others are operated on a monopolistic basis. Under a monopolistic setup, you have no choice, you must buy coverage from the state. Self insurance of the Workers' Compensation risk is also an alternative in most jurisdictions. With a contractor operating only in the U.S., the coverage extensions are few in number. If your work brings you anywhere near navigable waterways or land extensions thereof, you should have both U. S. Longshoreman and Harborworkers' coverage, as well as Employer's Liability coverage for the master or members of the crew of a vessel.

Jan 1, 1983

By Alan S. Peck

Chemisorbed oleate films on the surfaces of fluorite, barite, and calcite were studied by means of infrared spectrophotometry. Evidence is presented which indicates the mineral anions, i.e., fluoride, sulfate, and carbonate, are displaced from the mineral surfaces as a result of the adsorption from aqueous solutions. Also, chemisorption reactions between oleic acid and fluorite or calcite occurred spontaneously in the absence of water. Carbon dioxide was identified as a reaction product when dry calcite was contacted with oleic acid. There was no evidence of reaction between oleic acid and barite in the absence of water.

Jan 1, 1964

This paper was developed as part of an effort by the National Institute for Occupational Safety and Health (NIOSH) to identify risk factors associated with bumps in the prevention of fatalities and accidents in highly stressed, bump-prone ground conditions. Changes of failure mechanism with increasing confinement, from extensional- to shear-dominated failure, are widely observed in the rupture of intact specimens at the laboratory scale and in rock masses. In the previous analysis conducted in 2018, both unconfined and triaxial compressive tests were conducted to investigate the strength characteristics of some specimens of a Utah coal, including the spalling limits, the ratio of apparent unconfined compressive strength (AUCS) to unconfined compressive strength (UCS), the damage characteristics, and the post-yield dilatancy. These mechanical characteristics were found to be strongly anisotropic as a function of the orientation of the cleats relative to the loading direction.

Jan 7, 2020

By David S. Bolin, Gary R. Peterson

INTRODUCTION In both the United States and Canada, a company making a public offering of securities must comply with regulations which have been promulgated by Federal and/or Provincial Legislatures. This paper focuses on the regulations pertaining to reserve reports required by the United States Securities and Exchange Commission (SEC). SEC RESERVE FILINGS Reserve reports made to the United States Securities and Exchange Commission are the only reserve reports which are directly regulated by the United States government. The requirements for SEC reserve reports are set forth in the filing forms as shown in Appendix A, from Item 17A of SEC Form S-18. These reporting requirements, which are intended to protect the investing public from inaccurate or misleading claims, are primarily oriented to S-1 or other filings for new stock issues but must also be followed for annual 10K reports which must be filed annually by U.S. public corporations as part of the Corporate Annual Report. These undertakings require independent audits of reserves, mine designs, plant facilities and a general economic evaluation of the planned or existing operation as part of the backup documents for filing. An ore reserve is defined by the SEC as "That part of a mineral deposit which could be economically and legally extracted or produced at the time of the reserve determination". This definition is unchanged since it was last

Jan 1, 1988

By Deepak Malhotra

INTORDUCTION Mining operations are unique In that they handle large volumes of water (millions of gallons) daily. The water contains dissolved metals, processing chemicals, organics, and other contaminants, There are several sources of water contamination at mine sites: mines, mills, tailings ponds, and Industrial/utility complexes. Utility waste water generally represents a very small portion of the total process water utilized in a normal milling operation and hence will not be addressed in this paper. Mine drainage can represent a significant amount, thus having an Impact on the recovery of metals, especially In Industrial minerals operations, and may have to be treated separately. The National Pollutant Discharge Elimination System (NPDES) effluent limits are becoming more stringent, thereby requiring mining operations to treat process water prior to discharge to the environment. The general trend Is to move toward a closed-loop waste system and treat only that small fraction of process water which Is to be discharged to public lands. The following section discusses the reasons for waste water treatment and the existing and emerging technologies for meeting NPDES effluent limits. REASONS FOR WATER TREATMENT Due to the diverse nature of the mineral Industry, process/waste water contamination problems as well as processing flowsheets are site specific. However, certain generalizations can be made specific to processing of different minerals: • Acid mine drainage Is a problem at sulfide/coal mines. • Cyanide contamination of water Is a problem at gold processing plants. • Organics can be a problem at mines using flotation oils. • Tolling ponds are generally acidic at sites processing industrial minerals such as silica sand and feldspar. The cost for water treatment Is viewed as an added cost of production. Hence, large mines are moving toward dedicating personnel to management of water resources in order to minimize waste water for treatment. Very often, mines having closed-loop water systems will treat waste water for reasons other than meeting NPDES regulations. These Include situations where process requirements dictate use of high-quality water for separation of minerals, neutralization of acid mine drainage water, and portable water for the mill. WATER TREATMENT TECHNOLOGIES Water treatment process has to be cheap and simple because It has to process large volume, and It does not directly add to the bottom line, namely revenue. The water treatment process development has to be site specific because the contaminants In the water vary from site to site. and discharge limits for water vary from state to state. The current technologies for wastewater treatment have been divided Into the following three areas: • Removal of heavy metals • Cyanide destruction • Scale control A brief summary of the current technology In each area Is discussed below. Removal of Heavy Metals The physical and chemical processes for heavy metal removal are summarized in Table 1. The most common and cheapest approach has been the precipitation of hydroxides at high pH followed by sedimentation and thickening of solids. The remaining solids can be removed by filtration. The pH is adjusted back to neutral, and the water Is discharged. This process is most commonly used wastewater treatment technology in the mining industry. The basic processes can be modified by combining other operations in order to meet the objectives of the specific site as illustrated In the following examples: • AMAX's Mt. Emmons treatment facility uses Lectro Clear® process where the precipitated solids are removed by electroflotation. • AMAX's Climax Mine water treatment plant used Ion exchange columns to meet the discharge limits on molybdenum.

Jan 1, 1992

By S. L. Bessinger

Introduction In the design and specification of a ventilation system for an underground mine, it is necessary to make reasonably accurate estimates of the pressure losses in the various airways of the mine. These estimates can be made with little difficulty for open airways with simple geometric cross-sections, such as those cut by continuous miners or tunnel-boring machines. The situation is much different on a longwall face, where the airway's complex geometric cross section and the presence in the airway of obstructing equipment having a variety of shapes make it difficult, if not impossible, to estimate pressure loss using traditional methods of calculation. Head losses in mine entries are calculated using Atkinson's Equation. [22H= KPLQ (English) H= KP 3Q (SO (1) 5.2AA] where H = pressure loss, in. of H2O (Pa); K = friction factor, lbf•min2/ft4 (kg/m3); P = perimeter, ft (m); L = airway length, ft (m); Q = airflow quantity, ft3/min (m3/sec); and A = flow cross-sectional area, ft2 (m2) In this equation, the friction factor, K, is an empirical constant that describes the aerodynamic roughness of the airway. Typically, the K-factor for a given airway is determined by measuring the factors H, P, L, Q and A in Equation (1) and calculating K. Tables of friction factors calculated in this way are found in textbooks and handbooks that deal with mine ventilation analysis. Unfortunately, very few K-factors have been measured on longwall faces, and the accuracies of those that have been measured are entirely site specific, because of the wide variety of equipment found on longwalls. The development of a technique for prediction without mine-site measurements of the friction factor for any longwall face, regardless of its configuration, will thus be very useful in the design of ventilation systems for mines in which longwall mining is practiced. Calculation of pressure losses using Atkinson's Equation (1) and empirically determined K-factors provides accurate and useful approximations in cases where the airways have relatively simple cross sections. However, a careful analysis using the principles of fluid mechanics shows that such calculations are based on two assumptions that are not strictly correct when there are obstructions in the airway. The first assumption is that the air velocity distribution in the cross section, particularly around the perimeter, is uniform. This assumption results from the fact that the tabulated K-factor values found in the literature are based on field measurements with uniform conditions. Such uniformity does not exist in longwall airflows. The second common assumption is that the K-factor, and corresponding head loss, is independent of the Reynolds Number (NR) for a given flow. In fact, this assumption is not strictly correct, and is particularly erroneous in the case of irregular protuberances into the airflow, such as those found on a longwall face. The errors arising from the assumptions may be avoided by using K-factors calculated by a newly devised method, described below, which takes into account the fundamental principles of aerodynamic drag analysis. This new technique has two advantages: first, it is flexible enough to model any longwall, regardless of equipment configuration; second, it employs terminology and equations familiar to those who perform mine ventilation analysis, using K-factors, for which ventilation engineers have an intuitive understanding, rather than drag coefficients. To provide guidance for development of a longwall drag model, data were taken on two modern longwalls operating in substantially different conditions. Pressure measurements at Mine B were made with 200-foot (61-m) sections of 1/8-in. (3-mm) diameter plastic tubing, attached to a Dwyer Magnehelic gauge. Pressure drops were measured in 200-foot increments down the face, and summed to give the drop for the entire face length. This technique was found to produce small, repeated errors because of the number of segments required to span the longwall. At Mine A this problem was avoided by using a single, continuous, plastic tube for the entire face length. The psychrometric properties of the air were measured for both Mines A and B. A calibrated, standard vane-anemometer was used to measure the airflow on both faces. Finally, numerous dimensions were measured on both faces, and face profile drawings were obtained to allow detailed evaluation of the face equipment geometry. From this information, accurate evaluations of the average wetted perimeter and average area of the longwall face airways were made. Since the airflow is not confined to inside the powered supports at all points along the face, a quadratically weighted average of the airflows measured at various stations along the face was calculated: [n2Qavg =Qi Ii / It(2)i=1] where [Q, avg = average airflow for analytical purposes, ft3/min (m3/sec); Q= airflow at station i, ft3/min (m3/sec); 1= length of segment represented by Q, ft (m); h= length of longwall face, ft (m): and n= number of quantity measurement stations.] The quadratic weighting scheme was chosen because the

Jan 1, 1992

By C. Bazin

The fundamental error associated to the sampling of heterogeneous ore particles is unavoidable and can only be minimized by an adequate selection of the sample mass and/or size reduction of the sample before division into sub samples for testing or assaying. The preparation of ore batches to carry out the mineral processing evaluation of an ore is a sampling process. The fundamental error associated with the division of the ore into batches is responsible for the differences in the composition of the batches. This paper attempts by various means to assess the reproducibility of the gold content of test batches prepared from a gold ore sample. The results of the investigation shows that for fine gold grain sizes the variability in the composition of the batches is less than that predicted by Gy?s formula and that the gold grain size is a strategic information in the assessment of the gold content variability of test batches.

Feb 23, 2014

By Wm. Terry Siemer

Abstract. The value of industrial rocks and minerals produced in New Mexico in 1978 exceeded 227 million. 1e state ranked first in the nation in production of potash and perlite and was a leader in pumice production. Other commodities with sizable production in New Mexico include barite, caliche, clay, dimension stone, fluorspar, gypsum, humate, limestone, mica, salt, sand and gravel, scoria, and silica sand Non metallic resources are distributed throw out the state, but development and exploitation is concentrated in western and southeastern New Mexico. The value of industrial rocks and minerals within the state grew about 9 percent to more than $227 million in 1978. Continued growth, however, depends on continued demand, exploration, and development.

Jan 1, 1980

By O. Ogunsola, M. Downing

This paper gives a brief overview of impacts of coal blending on coal-fired power plants performance and discuses the preliminary results of an on-going study aimed at evaluating the effect of coal properties on the effectiveness, compatibility and thermal reactivity of coal blends. Plant survey studies reported no significant impacts on an existing plant designed for a high rank coal when switched to a blend of low- and high- rank coal. However, slight modification of some aspects (handling, fuel storage/stockpile, transportation, preparation, and general housekeeping) of plant design and operation may be necessary. The preliminary results of an on-going study at the Mineral Industry Research Laboratory shows that more compatible and better blends could be made from coals where ranks are closer than from those where ranks are far apart.

Feb 24, 1997

By I. WILKOMIRSKY, J. BECKER, F. Parada

Purification of molybdenite concentrate from copper concentrates was performed by sulfation. The sulfation of molybdenite concentrates was carried out with pure sulfuric acid (> 96%) at 160–190 °C to study the influence of the reaction temperature and reaction time on the residual copper in the molybdenite concentrates. A purified concentrate with less than 0.1 wt% copper and low levels of other metals were obtained. For up to 7.1 wt% copper, the conditions required are a temperature of 190 °C, a reaction time of 14 h, and a moly/acid weight ratio of 1/1. Furthermore, several designs of sulfation reactors were evaluated in order to obtain the desired level of copper in the product and to analyze the influence of the operational and design parameters on the reactor dispersion number (Le). The basic design for an 80-t/day plant fed with 4 wt% copper molybdenite concentrate requires five backmixed reactors in series, each measuring 8 m3, operating at 190 °C and with a reaction time of 10 h. The reactor must be protected against severe corrosion by the hot sulfuric acid with either Teflon, glass or ceramic.

Jun 14, 2022

By Feng Junfa, Du Feng, Li Huamin, Syd S. Peng

"The Ordos coal field is located in the northern midwestern part of China (Fig. 1). Since the mid- 1980s, it has been developed into one of the major coal fields in the world, producing approximately 833 Mt (918 million st) of raw coal in 2013. There were once more than 400 coal mines operating in the region. However, due to the combination of market conditions and implementation of government consolidation policies, the number of coal mines operating in recent years has been reduced considerably, with increasing output.The surface of the Ordos coal field is covered with loess and alluvium layers of varying thicknesses. In many areas, their combined thickness may amount to as much as 100 m (328 ft) underlain by thin bedrock. Many loess and alluvium are aquifers receiving water from rainfalls. There are also gullies of varying depths crossing the coal field. Figure 2 is a typical stratigraphic column highlighting the coal seams and roof and floor rocks of interest.In conjunction with the development of highproductivity coal mines, numerous ground control instrumentation tests have been conducted in the operating longwall panels. Analyses of the results of those tests offer the opportunity to understand the effect of wide-ranging mining and geological factors on the overburden movement. For this reason, trips were made to coal mines of interest to interview mine management and collect their unpublished internal research reports on ground control instrumentation. In addition, literature searches on published thesis/dissertations and papers in the professional journals were performed. Finally, data from a total of 95 fully mechanized longwall panels were collected. The instrumentation involved primarily the monitoring of hydraulic pressures of longwall shields, from which the first roof weighting and first roof caving interval and periodic roof weighting and periodic roof weighting interval were identified and determined. Some panels also included measurements of roofto- floor convergence at the face, roof strata bed separation, longwall face sloughage and the height of caving and fractured zones in the overburden. Those 95 panels were located in 20 coal mines (Fig. 1) congregated along both sides of the Wulunmulun River with the following mining and geological conditions. All together those 20 mines produced more than 224 Mt (246 million st) in 2013, accounting for approximately 27 percent of the total coal production in the Ordos coal field:1. Period of mining: 1991-2013.2. Mining methods: All panels employed the one slice, full-seam natural-caving longwall mining method like those practiced in the United States. All panels were developed with a twoentry system with a single-row of chain pillars measuring 20- x 20-m (65.6- x 98.4-ft) wide.3. Coal seams (Fig. 3): Coal in Ordos coal field is high-quality steam coal, that is very low in sulfur, potassium and ash, but high in Btu. Data were collected in panels mined in a total of 10 seams with 82 panels in four seams and the remaining 13 panels in six seams. The first six seams (1-2, 2-2, 3-1, 3-2, 4-2, 5-2) were mined by the Shenhua Coal Group (the world’s largest coal company) and the #4-2, 5-2, 6R, 62, and 62R seams were mined by both the Shenhua and Yitai Coal groups. In each coal group, the sequence of mining was in descending order. For example, in Shenhua Group, the top seam 1-2 was mined first, followed by the 2-2, 3-1, 3-2, and 4-2 seam in that descending order. In Fig. 3, the top-down sequence of coal seams is listed from left to right in each coal mine group. All seams were near horizontal with dip angles less than 3°."

Jan 1, 2014