Search Documents

By J. R. Patts, J. P. Rider, J. A. Organiscak, A. B. Cecala

"NIOSH recently completed a 15-month study at an underground limestone mine crusher booth which evaluated three research parameters: (1) the effectiveness of a single-filter filtration and pressurization system for improving the air quality inside the operator booth, (2) comparing the effectiveness of ? > 99 and ? > 95 experimental prototype filters in the system, and (3) evaluating the use of three different pressure monitoring devices to determine the performance of the filtration and pressurization system over time. The protection factor was quantified monthly using particle counters in the respirable dust range (0.3–10 µm), and gravimetric dust samples were gathered at the beginning and end of the overall study. Under static conditions and after outlier removal, the single-filter filtration unit installed offered a protection factor between 8 and 216, depending on the filter type and loading condition. The particle counting analysis shows that the ? > 95 filter offers a protection factor greater than 4-times that of the ? > 99 filter when evaluated over 60 minutes. The booth pressure monitors provided data that proved to be a valid indicator of system performance over time. INTRODUCTION Designed and installed correctly, enclosed cabs, operator booths and control rooms offer mine workers protection from physical hazards, such as flying rock, debris, and noise, as well as a more comfortable environment in regards to temperature and humidity [1]. But while it may be easier to quantify whether the A/C unit is working (measuring the temperature) or observe whether the cab offers protection from flying debris, it can be somewhat more difficult to quantify its performance in reducing respirable dust hazards. For over 15 years, NIOSH has been conducting applied research to improve the air quality inside of enclosed cabs of mobile equipment [2-5]. This work has led to the identification and mathematical modeling of enclosed cab filtration systems [6]. The same principles that govern the performance of filtration systems on mobile equipment are applicable to stationary enclosures such as operator booths and control rooms [1, 7]. Stationary enclosures are similar to enclosed cabs; however, the volume of the work area can be significantly larger. In addition, workers who perform their duties in stationary enclosures tend to stay within the room for a greater percentage of the day, as opposed to workers on mobile equipment who may enter and exit frequently. Structural integrity can be easier to maintain as well, as there is typically less vibration and stress placed on these compartments as compared to mobile equipment. In addition to offering protection from dust and flying debris, enclosures must ensure that workers have a healthy supply of fresh air to avoid elevated levels of CO2, which are known to cause headache and dizziness, impairing cognitive function. The American Society of Heating, Refrigerating and Air-Conditioning Engineers (ASHRAE) states that enclosures should have no more than 1,100 ppm of CO2 when outside levels are 400 ppm [8]. In addition, the American Society of Agricultural and Biological Engineering (ASABE) recommends a minimum airflow for enclosed cabs of at least 42.5 m3/hr (25.0 cfm) per person [9] to ensure an acceptable level of CO2."

Jan 1, 2017

By William L. Husk

Stockpiles have always been a necessary part of coal mining except, perhaps, when a person was mining only for the needs of his family from a seam on his home place or coal mined for the use of a small hamlet and carried to each man's house as it was mined. Then it may have been stockpiled at each man's place for several days or on the village common. Mining with this limited production required waste stockpiling. Stockpiling of the products of coal mining, both coal and waste material, has always been a necessity. Very little coal has ever been moved directly or immediately from the working face to the point of consumption and burned. It has always been expedient to stockpile the coal some- where and store the waste.

Jan 1, 1981

By Jürgen Kretschmann

According to the model of product life cycles, the global coal mining industry is in the stagnation phase. The coal demand of the main consumer, China, has peaked in 2013 and is slowly declining. The Norwegian sovereign wealth fund, the world’s largest, has excluded coal-related companies for ethical reasons. Important players like the UN or the EU have already begun to describe pathways towards decarbonization. Increasing competition between coal mining companies and the mining regions can be expected worldwide if companies want to keep their positions on the global and national coal markets. Companies will focus on the best deposits. European countries like France, Spain, or Germany are only forerunners of this development—their centuries of coal production have been finished. The concept of sustainable development (SD) is fundamentally based on a model of progress where ecological, economic, and social dimensions should be developed equally and positively. But without the idea of competition, the concept of SD is incomplete. Questions arise, such as how can SD be realized on stagnating or declining markets without guarantees for companies “to live forever”? How can SD be a corporate goal in a phase of decline? How can declining mining regions sustainably progress into a better future? The German hard coal mining industry’s lifecycle has ended in 2018 after 60 years of stagnation and decline. As of 2019, all hard coal consumed in Germany will be imported, especially from Colombia, Russia, and South Africa. What has been done in Germany to handle the coal decline in a sustainable way and the lessons learned from this process is described in this paper. It may be useful for mining regions who will face a similar future sooner or later.

By Charles Dumaresq

The management of mine tailings poses a complex range of potential risks, including physical risks, such as the risk of catastrophic failure of a tailings facility and chemical risks such as the risk of long-term leaching of contaminants into the downstream environment. If these risks materialize, they can lead to a wide range of impacts on people and the environment, including human fatalities and severe impacts on downstream ecosystems, and the costs of recovery borne by industry, communities, governments, and society as a whole can be immense. Tailings facility failures in Canada (2014), Brazil (2015 and 2019), South Africa (2022), and in other locations around the world underscore how high the stakes are when mines produce and manage tailings (WISE Uranium Project 2019). Understandably, many people do not trust the mining industry to manage tailings responsibly. As an industry, it is our responsibility to manage tailings in a manner that is responsible and strives to minimize harm associated with tailings management, including effectively managing both the physical and chemical risks associated with tailings. Standards have an important role to play in responsible tailings management by setting expectations for standards of care and providing a means to measure and report on performance. In jurisdictions with strong legal requirements for tailings management, standards play a complementary role, pushing performance improvements in areas that may be difficult or impossible to address in legal requirements. In jurisdictions where legal requirements are lagging, standards may represent the de facto leading practice and may be the primary tool to help ensure responsible tailings management. Implementation of standards can help companies demonstrate that tailings are being responsibly managed and help build trust and credibility. Most importantly though, standards are important tools to help ensure that the risks associated with tailings are reduced, and that remaining risks are effectively managed. However, we must recognize that conformance with standards can have a down-side – the proverbial two-edged sword. Having standards is vital but there is a risk that implementing standards becomes a “box checking” exercise, with ongoing conformance leading to complacency. We must not allow ourselves to fall into the trap of believing that, just because we are complying with applicable standards and laws, we are therefore doing our best, and that “it can’t happen to us.” In addition, if conformance becomes the goal and the standard does not have mechanisms to drive continual improvement, then once the standard is met, there may be no incentive to improve. The point of complying with standards is not to pass the test. The point is to manage tailings responsibly, prevent catastrophic failures, and minimize harm. The point is to do better, because we must do better. To do that, we need to strive not for conformance, but for excellence in tailings management, driven by continual improvement and a quest to do better.

Feb 1, 2025

By J. A. Ehler

Speed and torque control of standard A.C. induction motors can be accomplished using a variety of devices ranging from mechanical, hydraulic, and electrical. Also, the motor can be specified as an A.C. wound rotor or D.C. motor using the associated controls. Normally, any one of these drive types can be adequately used to provide the torque control necessary to accelerate a conveyor belt system. The selection will depend on the economics, experience, and preference of the designer or end user. These drive types will be presented from a functional and performance viewpoint to assist in the understanding of the available technology.

Jan 1, 1998

By J. D. McAteer

It is widely agreed throughout the mining community that federal mine safety and health legislation administered by the Mine Safety and Health Administration (MSHA) deserves significant credit for the past quarter-century's remarkable improvements in miner safety and health. Recently, however, it has been suggested that the mining industry in the United States has now evolved to a point that current mine safety and health law may be obsolete. This proposition deserves attention. Today, I propose to give it the close logical scrutiny that is its due. I conclude that the obsolescence of current mine safety and health law is not supported by the evidence. The existing mine safety and health law continues to serve as a critically important supplement to mine operators' safety programs at a modest cost to the taxpayer. At the same time, trends in a changing industry do call for responsive adaptations in the Federal mine safety and health program. I will argue that timely and appropriate responses to changing needs can be accomplished within the framework of existing legislation, provided federal officials avail themselves of the flexibility provided by existing law.

Jan 1, 1996

By R. Heiser, J. Vendetti, B. P. Connor, E. J. Haas

Health and safety indicators help mine sites predict the likelihood of an event, advance initiatives to control risks, and track progress. Although useful to encourage individuals within the mining companies to work together to identify such indicators, executing risk assessments comes with challenges. Specifically, varying or inaccurate perceptions of risk, in addition to trust and buy-in of a risk management system, contribute to inconsistent levels of participation in risk programs. This paper focuses on one trona mine’s experience in the development and implementation of a field-level risk assessment program to help its organization understand and manage risk to an acceptable level. Through a transformational process of ongoing leadership development, support and communication, Solvay Green River fostered a culture grounded in risk assessment, safety interactions and hazard correction. The application of consistent risk assessment tools was critical to create a participatory workforce that not only talks about safety but actively identifies factors that contribute to hazards and potential incidents. In this paper, reflecting on the mine’s previous process of risk-assessment implementation provides examples of likely barriers that sites may encounter when trying to document and manage risks, as well as a variety of mini case examples that showcase how the organization worked through these barriers to facilitate the identification of leading indicators to ultimately reduce incidents.

Jan 1, 2018

By R. Heiser, J. Vendetti, B. P. Connor, E. J. Haas

Health and safety indicators help mine sites predict the likelihood of an event, advance initiatives to control risks, and track progress. Although useful to encourage individuals within the mining companies to work together to identify such indicators, executing risk assessments comes with challenges. Specifically, varying or inaccurate perceptions of risk, in addition to trust and buy-in of a risk management system, contribute to inconsistent levels of participation in risk programs. This paper focuses on one trona mine’s experience in the development and implementation of a field-level risk assessment program to help its organization understand and manage risk to an acceptable level. Through a transformational process of ongoing leadership development, support and communication, Solvay Green River fostered a culture grounded in risk assessment, safety interactions and hazard correction. The application of consistent risk assessment tools was critical to create a participatory workforce that not only talks about safety but actively identifies factors that contribute to hazards and potential incidents. In this paper, reflecting on the mine’s previous process of risk-assessment implementation provides examples of likely barriers that sites may encounter when trying to document and manage risks, as well as a variety of mini case examples that showcase how the organization worked through these barriers to facilitate the identification of leading indicators to ultimately reduce incidents.

Jan 1, 2017

By A. E. Halim, J. F. Brune

The 2006 Sago, Darby, and Aracoma mine disasters in the United States (US) forced the US government to implement the 2006 MINER Act and additional regulations that require all US underground coal mines to install and maintain refuge chambers to manage entrapment emergencies, in particular, fires and explosions. However, there is a debate on whether barricading in refuge chambers is a good strategy to survive such emergencies. Australian coal mines are not required to use refuge chambers and, instead, have adopted a strategy that focuses on instructing and training miners to self-escape to the surface. This paper analyzes merits and problems of using refuge chambers and self-escape to the surface to manage emergencies in fires or explosions in an underground coal mine. The authors found that the use of refuge chambers may not be the best strategy during extensive fires or when multiple explosions happen. In these situations, mine rescuers are unlikely able to extract miners who are sheltered in chambers and conversely, self-escape may save more lives than sheltering. Chances for successful self-escape are further improved by regular, externally assessed training such as Level 1 Emergency Exercises required in the Australian State of Queensland. These exercises put pressure on mine operators to ensure and maintain the effectiveness of their emergency management system.

By John K. Liu

The trend to larger grinding mills, requiring total drive power in the range of 10,000 KW(13,400 HP) or so provides the incentive for developing new power transmitting techniques, since conventional girth gears are limited to about 3700 to 4500 KW per mesh (5000-6000 HP). For the immediate future, the synchronous motor, with its beneficial power factor, and the squirrel cage induction motor, with its high reliability record and low maintenance, still promise to be the best choice for prime mover(s). Due to the abovementioned single mesh power limitation of the gear train, however, two or more motors must be combined to attain the required drive power. This paper describes a scheme for coupling these motors to the mill using a straightforward, essentially mechanical means that is based on proven components and controls.

Jan 1, 1977

By Aurel Goodwin

I chose the title "Let's Clear the Air" for this afternoon's presentation because it has two meanings, the literal and the figurative. Most of you know what MSHA is. Most of you know what MSHA does. And, for the most part, most of you know why. What I hope to accomplish today is to "clear the air" around our health standards, to clarify for you how MSHA views its congressional mandate under Title I Section 101(a)(6), (7), and (9) of the Mine Safety and Health Act. Asbestos, silica, radiation, noise, welding fumes, carbon monoxide, lead, hydrogen sulfide, nitrogen dioxide - the list of physical and chemical hazards encountered in the metal and nonmetal mining industry is as diversified as the industry itself, possibly even more so. In addition, miners are often exposed to several of these health hazards simultaneously.

Jan 1, 1980

By Jürgen Kretschmann, Christina Suarez, Jürgen Brune, Stefan Möllerherm

"The Ruhr region in Germany’s North-Rhine Westphalia is going through significant change. By the end of 2018, the last two underground hard coal mines in the Ruhr, Ibbenbüren and Prosper-Haniel collieries, will close their portals and bring an end to more than 200 years of coal mining and an industry that was once the economic and cultural backbone of the area. Ruhr is undergoing an impressive economic and cultural transformation, as it gradually shifts from being a region once dependent on coal and steelmaking to a post-mining region focused on redesigning itself as a cultural center. This article focuses on the socioeconomic impacts of the transformation into post-mining and the roles of the government, labor unions and local community to aid the transformation from the perspective of an American student. It will look into the cultural values that are helping to drive the transformation and compare them to American standards and values in order to determine if a similar approach can be used in the United States and its coal industry. History and backgroundUnderground hard coal mining has had a long history and a significant impact on the culture and economy in Ruhr since the early 19th 20century. The Ruhr region is located in the heart of the German state of North- Rhine Westphalia. Ruhr is bounded by the Rhine River in the west, the Ruhr River in the south and the Lippe River in the north, with the Emscher River running through its center.The Ruhr is home to around 5.1 million people and spans an area of approximately 4,500 km2 (1,730 sq miles). Before the era of industrialization, the Ruhr was a rural, agricultural region. Small-scale coal mining began in the 13th century, with coal being used for heating, cooking and metallurgical processes, including steelmaking. With 19th-century industrialization, coal mining became a significant driver of the region’s economic structure. Steam engines, and soon, electric motors, allowed for the pumping of mine water and for powerful hoists hauling from deep shafts, enabling miners to reach deeper coal seams that were once thought impossible to mine. The Ruhr mining boom began in the 1850s, supported by Prussian economic policies that attracted many workers and their families to the region. The population grew from 400,000 in 1850 to 5.7 million in 1957. The coal and steel industries were key contributors to Germany’s “Wirtschaftswunder” — or “miraculous economic recovery”— in the 1950s. In 1956, the coal industry reached its peak production of around 112 Mt/a (124 million stpy) of coal and employed almost 600,000 miners."

Mar 1, 2019

By D. Farnell

Large semi-autogenous (SAG) or autogenous grinding mills have become the work-horse of the modern high volume concentrator. They typify the economy of scale - fewer, larger machines doing more work, more economically. With fewer machines, equipment reliability becomes of paramount importance. Realizing this, companies installing new or modernizing existing facilities have placed extraordinary emphasis on purchasing a reliable mill. This, in turn, has had a significant impact on mill design. Kennecott And Codelco - Two Different Approaches Last year, two of the world's largest copper producers, Codelco and Kennecott, undertook the modernization of their main grinding facilities at Chuquicamata and the Utah Copper Division (UCD) respectively. Both selected semi-autogenous milling and both, recognized the importance of the reliability of the primary mills. Each, however, decided on a different approach to optimizing reliability. Codelco placed the emphasis on technical innovation in design and opted for a gearless driven mill. Kennecott chose the more conservative approach of active participation and exceptional quality assurance in mill design and manufacture.

Jan 1, 1987

By Jürgen Kretschmann

According to the model of product life cycles, the global coal mining industry is in the stagnation phase. The coal demand of the main consumer, China, has peaked in 2013 and is slowly declining. The Norwegian sovereign wealth fund, the world’s largest, has excluded coal-related companies for ethical reasons. Important players like the UN or the EU have already begun to describe pathways towards decarbonization. Increasing competition between coal mining companies and the mining regions can be expected worldwide if companies want to keep their positions on the global and national coal markets. Companies will focus on the best deposits. European countries like France, Spain, or Germany are only forerunners of this development—their centuries of coal production have been finished. The concept of sustainable development (SD) is fundamentally based on a model of progress where ecological, economic, and social dimensions should be developed equally and positively. But without the idea of competition, the concept of SD is incomplete. Questions arise, such as how can SD be realized on stagnating or declining markets without guarantees for companies “to live forever”? How can SD be a corporate goal in a phase of decline? How can declining mining regions sustainably progress into a better future? The German hard coal mining industry’s lifecycle has ended in 2018 after 60 years of stagnation and decline. As of 2019, all hard coal consumed in Germany will be imported, especially from Colombia, Russia, and South Africa. What has been done in Germany to handle the coal decline in a sustainable way and the lessons learned from this process is described in this paper. It may be useful for mining regions who will face a similar future sooner or later.

By Ronald C. W. Webber‑Youngman, Philani Larrance Ngwenyama

Entrapments are a huge risk in underground mines. This happens when miners (or any other persons who have entered underground) survive the initial event of an accident, become trapped or lost in unknown and life-threatening locations after evacuation, and remain unaccounted for. At this point, every second counts, and emergency response is highly desired for any chances of saving survivors. The survival chances of the missing persons depend on how quickly they can be located. Rescue teams are often deployed to search for the missing persons underground. However, the rescue teams are forced to search in random and presumed areas of the mine. This is due to the unavailability of information pertaining to the whereabouts of the missing persons. Not only the provision of accurate locations, but various other types of information such as post-accident two-way communication can enhance the survival chances of the missing persons. This information can be provided by a fit-for-purpose missing person locator system. A wide variety of missing person locator systems are already commercially available, some are in testing phases and others in prototype and development phases. This includes tracking, tracing, location detectors and post-accident two-way communication systems. These systems have unique functionalities, capabilities and limitations; making it difficult for mines to select the most effective, applicable and suitable system specific to their mine. In this study, the user requirements for a fit-for-purpose missing person locator system were developed. The purpose of the user requirements was to provide a guideline to facilitate the system selection process. The user requirements can also be used as a tool to measure and evaluate the performance of the selected missing person locator system. The user requirements were also used to predict the success of the selected system under different missing person incident scenarios. The development of the user requirements showed a potential for many other benefits for missing person locator systems.

Nov 2, 2023

By M. A. Trevits, G. W. Luxbacher, L. D. Patts

"It is almost a given that post-disaster mine conditions will have compromised the mine ventilation system, resulting in a hazardous atmosphere in portions of the mine, and often complicated travel through debris fields and roof falls. Robotic technologies provide the opportunity to gather valuable information to assist decision making or lessen exposure to dangerous conditions. MSHA's Mine Emergency Operations Division (MEO) has utilized a fully permissible mine robot, the V2, for a number of years, constantly updating the unit as new technologies became available. The National Institute for Occupational Safety and Health, as part of the MINER Act Extramural Contract Program, examined the need for additional robotic units and ultimately funded three different types of prototype technologies: two robots, the Snake Robot and the Gemini-Scout, and a mine rescue robotic assist vehicle known as the ""Mule"". The Snake Robot is designed to be lowered through a borehole and to conduct surveillance (gas monitoring, video and audio) in the immediate vicinity, while the Gemini-Scout, designed to be deployed in the mine opening, serves as a more mobile and agile exploratory tool as compared to the MSHA V2 robot. The Mule was developed in response to needs expressed by mine rescue teams for a versatile remotely operated support vehicle and it will move from prototype to MEO utilization in the near future. This paper describes the development of the robot prototypes and discusses their limitations in the prototype stage, possible enhancements and potential applications, as well as the utilization of the Mule. INTRODUCTION The conditions in a coal mine may be dramatically altered after a mine fire or explosion. For example, the ventilation system may not be functioning correctly as control devices may be compromised or damaged beyond repair. The visibility in the mine opening may be limited due to accumulated smoke and dust. Roof support systems may be damaged or no longer functional. Equipment and materials may be strewn about the mine opening. Debris fields, blocked openings, roof falls, flooded areas, gas accumulations and active burning make it very difficult or impossible for those managing the post-event emergency to permit mine rescue teams to enter the mine to conduct search and rescue operations. With the evolution of robots and robotic assist technology there has been a proliferation of purpose-built units for the military, police and law enforcement agencies, urban search and rescue and those contending with hazardous environmental conditions. In each case, the technology used is designed to limit human exposure to the unsafe conditions or to provide access to areas under difficult conditions. For example, a specially-designed marine robot has been deployed into the damaged core of the Japan’s Fukushima Daiichi Nuclear Power Plant to assess the conditions of the containment vessels, where melted fuel is believed to have accumulated. Human access to the area is prohibited due to dangerously elevated levels of radioactivity [1]. Multiple robots were deployed in Amatrice, Italy, to assist in the response after the 6.2-magnitude earthquake devastated the town. The robots were used to explore two medieval churches that were severely damaged and deemed too dangerous for human entry [2]. Tactical robots are regularly used by police and law enforcement agencies when the conditions of the emergency place intervening officers directly in harm's way [3]."

Jan 1, 2018

By Ray H. Hario

Background of Erie Mining Company Erie Mining Company, managed by Pickands Mather & Co., is one of the largest producers of iron ore pellets in the United States. The plant is located at Hoyt Lakes, Minnesota, sixty-five miles north of Duluth on the eastern end of the Mesabi Range. Taconite Harbor, situated on the north shore of Lake Superior, is the location of its Power Plant and shipping facilities. (Figure 1) Even though the plant commenced operation in September, 1957, its true be-ginning can be traced back to 1931 when Pickands Mather, in conjunction with Bethlehem Steel Corporation and Youngstown Sheet and Tube Company, began investi-gating the possibilities of processing low grade ores. In 1940, Erie Mining , Company was formed. During the early and middle 1940's, laboratory and pilot plant research was proven to a point where a preliminary plant was deemed feasible and built in 1948. This plant had an annual capacity of 203,200 t (200,000 long tons) per year and, until mid-1952, was the only taconite plant in existence using commercial-size equipment. During this period, ownership of Erie Mining Company was expanded to include Interlake, Inc. and The Steel Company of Canada, Limited. In 1953, authorization was obtained from the owners to build a 7.62 M t (7.5 M long tons) per year plant at a cost in excess of $300,000,000.

Jan 1, 1977

By Mehmet Guney

Acceptable working environments in production areas and service openings of Mindola Mine on the Zambian Copperbelt are currently maintained with an air volume of 1000 cu m/s and 5500 kW of installed refrigeration plant. It is planned to open up additional deeper areas of the mine for future production. Temperature problems, due to the increased heat generation from various underground sources are recognized as potential hinderances to efficient production. Findings of research work indicate that the present total heat output of 58,000 kW will inevitably increase by the second five-year period of the deepening program to 52,900 kW and by the fifth five-year period to 63,200 k\V. Estimated WB and DB temperatures, representing the total heat generation in stope faces and development headings during these same periods are predicted to increase to 53.8/40.2 °C and 35.5/42.1 °C respectively. It is assessed that the nominal refrigeration capacity needs to be progressively increased to 9,000 k\V This paper deals with the thermal problems in Mindola Mine, current heat output calculations, future prediction of temperature and heat load in various working areas of the mine with the application of computer programs and interpretation of data in order to find the effective solution for long-term planning of ventilation and air-conditioning.

Jan 1, 1982

By Edgar T. Gregory

A quiet revolution has taken place in the conveyor belt industry, Man-made materials, improved production facilities, better splicing techniques and emphasis on repair and maintenance have all contributed substantially to lowering material handling costs for the mining industry, It wasn't too many years ago that the rubber industry had only cotton for a belt carcass and tree grown rubber for the protective cover. Then came the development of monofilament rayon. This material had desirable elongation and elastic properties and was the first synthetic fiber to be used in place of cotton. But wet strength and other limitations restricted its use, and the conveyor belt industry turned to nylon. Initially, nylon was considered suitable only for the cross threads or filler threads of a belt carcass. Then technical advancements in heat setting and fabric weave created a major change in belt construction. As a result of these advances the industry was able to take advantage of the full tension strength of nylon cord. Another breakthrough in the use of synthetics was the tremendous increase in adhesion resulting from a chemical bond, rather than the limited physical bond available with cotton. But the advantages of nylon had a more Car-reaching effect, We were able to design a two-ply nylon belt that did the work of a four- or five-ply cotton or rayon belt. A six-ply nylon belt now replaces a twelve-ply cotton elevator belt. Arid nylon resists moisture, acid and mildew, It also has excellent resistance to impact and can be produced with controlled elongation and elastic properties that work to great advantage in reduced-ply belt constructions.

Jan 1, 1971

By Leonard Sugin

The requirements of today's and tomorrow's markets led to a new generation of facilities which handles large tonnages annually, loading them into larger vessels, at higher rates, efficiently and reliably, with minimum labor input, and significantly greater attention to the environment. A great variety of products are handled, including various grades of metallurgical and steaming coal, coke, iron ore in its many forms, shapes and moisture content, phosphates and fertilizer products, bauxite and alumina ores, limestone, sugar and grains, cement and many other products. When we examine the annual tonnages involved in these movements the economic value of handling these products on a bulk basis can be readily seen. Although nearly all these products have been handled by continuous bulk conveyors for many years, recent governmental response to environmental concerns require a re-evaluation of previous procedures. Most air pollution and emission control regulations and ordinances have recognized several specific sources of pollution. Detailed regulations and requirements have been developed concerning smoke emissions, emissions of visible air contaminants and particulate matter from power plants, heating plants, refuse burning equipment, coke ovens, steel furnaces, kilns, and other industrial installations. Although fugitive dust is also an environmental pollutant it is governed by regulations that are more general and therefore, more difficult to apply. A general definition of a "fugitive particle" is any matter which escapes or becomes airborne from an operation or which is emitted into the atmosphere without passing or being conducted through a flue, pipe, stack or other structure designed for the purpose of emitting air pollutants into the atmosphere. This paper deals with the aspects of fugitive dust emissions as they apply to shiploading. Fugitive dust emissions control is important not only because of environmental regulations but also to prevent the loss of valuable product, reduce housekeeping, and reduce breakdown and maintenance problems to land and vessel equipment. The environmental controls for a belt conveyor system are those which will restrict the emission of fugitive dust particles and can be considered as follows:

Jan 1, 1977