Search Documents

A clay binding agent has been investigated to enhance flotation recovery of bitumen from Canadian high fines oil sand in the Clark Hot Water Extraction (CHWE) process. Selective adsorption on fine particles and subsequent agglomeration are critical for the success of clay binder enhanced oil sand flotation. A number of flotation tests have been performed at different reagent dosages under different operating conditions such as pulp pH to evaluate the reagent performance. Dissipative Quartz Crystal Microbalance (QCM-D) analyses of clay binder adsorption on quartz were carried out to better understand process mechanisms. It has been found that use of clay binder in flotation resulted in an absolute bitumen recovery increase of 18%, 25%, and 11% for the high-, medium-, and low-grade oil sand samples, respectively. The QCM-D analyses have revealed that the clay binder was strongly adsorbed on the SiO2 surface.

Jan 1, 2012

By James W. Furlow

A recent attempt by a major mining company to mine phosphate in Chatham County, Georgia, resulted in a study by the Georgia Department of Mines, Mining and Geology which was intended to evaluate the deposit as well as potential hazards to the major fresh-water aquifer of the area. The study found that the confining layer above the fresh-water artesian aquifer is sufficiently thick and impermeable to allow removal of the phosphate ore zone without significant salt water infiltration into the aquifer. Therefore, phosphate mining under proper supervision will not adversely affect the quality of water used by the city of Savannah nearby. Volumetric studies show that there is a minimum of 4,800,000,000 cubic yards of phosphate matrix containing an average of 22.5% BPL. At an approximate weight of 1.5 tons per cubic yard and a concentration of 22.5% BPL, there are about 1.6 billion tons of 100% BPL concentrate present. At a conservative factor of 50% at least 800,000,000 tons of 100% BPL concentrate could be recovered for market sale. In addition to the area discussed, evidence indicates that the phosphate horizon-may extend continuously out to sea for at least ten miles, and probably beyond.

Jan 1, 1972

By SH. Shahsavari, H. Akbari, M. Noaparast, M. Oliazadeh

Mejel valley zircon ore in Iran is located in north part of Iran and was sampled to evaluate its concentration. The aim of this project was to define the mineralogy of this zone and separating zircon from other minerals using gravity concentrators and magnetic separators. It is constituted of various valuable minerals, mainly zirconium, niobium-tantalum, titanium, rare earth elements particularly cerium-bearing minerals namely zircon, sphene and rare earth elements oxides. We used statistical method for designing of experiments. Yates method used for analysis of basic experiments results. The grade of zircon in primary sample was 1.1%. Different experiments were designed to optimize all required parameters. The final concentration with 75% zircon was produced and final recovery was 79%. Finally, lab-scale based flow sheet was prepared using experiments results.

Jan 1, 2005

By Hayward B. Oblad, Gary F. Meenan

Two optoelectronic detectors were developed by CONSOL R&D for fine coal processing applications. One sensing device is used to estimate the amount of fine coal in the solids fraction of the froth flotation tailings slurry. The other probe, based on similar technology, is capable of measuring sol ids concentrations as high as 10 weight percent in fine coal slurry streams. These patented optoelectronic sensors are installed in several CONSOL coal preparation plants and are an integral part of the fine-coal control systems.

Jan 1, 1993

By Betty L. Gibbs, Jean A. Arcamone

Introduction Microcomputers are becoming more convenient to use at all levels in the business world, including the mining industry. The state of the mining industry requires that we become more productive and innovative in our analysis of deposits and operations. With the help of computers, examination of options to increase productivity can be performed quickly and inexpensively. Effective computer use to design underground workings combines the calculating power and speed of a computer with the technical expertise and judgment of an engineer. Computer programs can perform in minutes calculations that might take several months for an engineer. But the engineer must be on guard when using computers for calculations. It is easy to assume the results produced by a computer program are always correct. However, the computer is only a sophisticated calculator. It cannot recognize logical errors or transposition of numbers. Also, some intuitive or obvious decisions made by an engineer are difficult or impossible to program effectively. In this article, selected commercial programs are discussed. These programs can provide engineers with tools to evaluate engineering designs for underground mines. The programs perform much of the tedious calculation. The engineer, though, must still make decisions and conceptualize designs. The software mentioned in this article runs on microcomputers and minicomputers. The mention of particular software, however, does not imply endorsement. Mining projects After a decision has been made to proceed with an underground mining project, more detailed evaluation of the mining method and extraction sequence begins. If a mine is already in operation, schedules and plans are needed to more clearly define future production. Existing operations can benefit from identification of bottlenecks in material movement and produce extraction options to make the mine more efficient. Detailed studies for a new mine are based on the technical engineering design. These studies provide specific details to determine equipment requirements. Detailed studies done during a project are similar to short-term planning and control carried out daily by the mining engineers. The engineering design phase includes: • Study of the infrastructures - entries, shaft, access from surface to underground; • Definition of the mine layout, hydrogeology, geotechnical considerations, transport, and ventilation; • Choice of machines and equipment; • Mine scheduling, including waste extraction and production sequencing; and • Economics, including labor and supplies. Further detailed studies include: • Blasting patterns; • Detailed geotechnical calculations; • Secondary ventilation; and • Production cycles along with coordination of the workings. Objectives The primary objective of underground mine planning is moving material out of the mine at the least cost. Development of the production schedule considers location and volume of ore units, transport distance, equipment and manpower interactions, and grade or quality of material. Two methods can be used to determine the scheduled material removal: optimization or trial and error. The microcomputer programs discussed here do not cover optimization for underground mine planning. For several reasons, optimization is often a "black box" approach. Although optimization is possible with linear programming techniques, few mining operations can be described effectively with linear equations. An interactive trial-and-error approach is desirable because engineering judgment can be inserted as a plan develops. Because of the large number of factors in an underground operation, an optimization technique seldom covers all possibilities. Few of the programs available consider all of the possible parameters. The programs use an interactive sequencing or a simulation approach and are either event-oriented or deposit-oriented. The most desirable programs offer an integrated approach. They consider a broad range of operating conditions including equipment, labor, costs, material movement, timing, and mine layout, among other factors. The two types of models generally used in designing underground workings include: • The interactive model, which requires direct, incremental input from the user. Outlines of the section to be mined may show on the screen. The engineer causes the model to develop piece-by-piece. The program may offer feedback on parameters such as tons and grade, or other values, as the section is "mined." • The simulation model, which is usually an automatic technique. Parameters related to the process are entered. The program then calculates the mining sequence over a designated time period or until the economic material is exhausted. A simulation model imitates step-by-step performance of equipment or other processes.

Jan 3, 1988

By A. Davaliev, K. Hrkovic, V. Pavlovic

On the territory of Macedonia in South Yugoslavia primary and dory gold occurences were known since ancient times. Remnants of numerous goafs and remainders of washaries on river terraces and alluviums date right back to the times of Phillip II and his son Alexander of Macedonia and from Roman times, as well as from the Middle Ages witness exploitation of primary and secondary gold. More recent explorations on primary and secondary gold occurrences date from the period between two World Wars. Over that period a number of private companies, each on their own jointly, carried out gold exploration, particularly of alluvial occurrences on rivers emptying into River Vardar, starting from Skopje to the Greek frontier. The latest gold explorations carried out In the alluvium of River Konjska date back in 1976, and in 1978 old terraces of River Konjska were explored. The Visibility Study was prepared on possibilities of exploitation of gold from River Konjska alluvium. In the paper are collected the basic date an all known primary and secondary occurrences of gold, the results of the latest explorations, and the study itself. To-date geological explorations and analyses show very interesting potentionality of River Konjska and River Vardar alluvium, which proves continuing of he further explorations. For the moment, it is necessary to re-explore more complete view of the deposit. After that it will be possible to make complete techno-economical estimation of the auriferious alluviums and the conditions of the evaluations of the alluvial gold. 1. REVIEW OF PRIMARY AND SECONDARY GOLD DEPOSITS IN MAOEDONIA,YUGOSLAVIA 1.1. Primary deposits Scarse data are available for primary gold deposits in Macedonia` being unadequate for clear

Jan 1, 1988

By M. P. Adamson, Bryson D. Trexler, R. V. Ramani, Mark L. Koenig, V. Rajaram, Alan Burton, C. S. Crocker, Kim. Y. C., A. G. Law, William C. Larson

Another record year vas experienced by the mining industry as the value of nonfuel minerals production soared to $23.5 billion-up 15% from the previous year. Based on preliminary estimates by the Bureau of Mines, US mine output was the basis for about $225 billion worth of minerals-derived materials. Metal mining accounted for $8.5 billion, or 36%, of the total. Of the 22 metals produced in the US, 11 showed quantity increases, while 16 had value increases. Business Week's survey of 1200 companies (Mar. 17, 1980, pg. 81) revealed that 21 metals and mining companies had sales increases of 30% with earnings up 104%. Higher prices and increased demand for metals were primary factors behind the improved performance. The steel sector reported a 30% decrease in earnings for the year, but the slump was primarily the result of a $383-million loss for US Steel coupled with a 17% decrease in earnings at Inland Steel. Other firms did well in 1979, with earnings up 279% at Interlake and 269% at Kaiser Steel. Major obstacles facing the steel industry included substantial tonnages of dumped and subsidized imports, environmental expenditures, runaway inflation, and price controls. Turning to nonmetallic production, of the 49 commodities reported by the US Bureau of Mines, 29 had higher outputs and 39 had increased values. While production statistics may seem encouraging, government regulations continued to stifle industry efforts to develop needed new capacity. A case in point may be publication of the Environmental Protection Agency's simplified procedure to streamline five permit programs by consolidating them into one. The five included: hazardous waste management, national pollution discharge elimination, dredge and fill, underground injection control, and prevention of significant deterioration. The new procedure, published by EPA in the Federal Register, took 149 pages. AMC's J.A. Overton, Jr., noted that (MCJ, Nov. 1979, p. 39) to visually depict the complexity of the proposed regulations, Sell Oil Co. developed a flow chart mapping a path through one section. The chart required 10 days to map and two weeks for two draftsmen, using computerized drafting techniques, to plot the results. Overton said, "Perhaps the greatest service EPA has performed in preparing its proposal is to demonstrate again that federal regulations have become a complexity compounded by confu¬sion that culminates in a conundrum." While regulatory agencies promulgate new regulations, the lack of a cohesive government minerals policy remained a matter of significant importance to mine management. A non-fuel minerals study to provide input to the Administration for a national minerals policy program was a dismal shock, according to Rep. Jim D. Santini (D-NV). He said the first phase of the program, which was to identify industry problems, failed to come to grips with the hard decisions necessary regarding these problems, their impact, and their interrelationship. Santini said the report failed to acknowledge government's role in the process and absolved the government of any adverse influence on the domestic minerals industry. In response to the phase one report, eight senior mining executives testified before Santini's House Subcommittee on Mines and Mining concerning mineral supply, access to foreign sources, environmental protection, conservation and recycling, national security, and capital formation. By year's end, Rep. Santini promised to prepare a hard-hitting committee report on problems affecting the non-fuel minerals industry to provide a better base for subsequent policy recommendations (MCJ, Jan. 1980, p. 34). On the technological front, interest again centered on mechanization, automation, and scaleup to improve and expand production. Computer use increased for calculation of ore reserves, mine planning, operations research, and mineral processing.

Jan 5, 1980

By F. Freme

Coal production in the United States in 2008 reached a record level of 1.06 Gt (1,171.5 million st), according to preliminary data from the U.S. Energy Information Administration (EIA) (Table 1). This is an increase of 2.2 percent, or 22.5 Mt (24.8 million st) above the 2007 level and 7.9 Mt (8.7 million st) above the prior record level set in 2006. Although coal production was higher in 2008, U.S. total coal consumption decreased in all sectors for the year. Coal consumption in the electric power sector in 2008 was lower by 0.3 percent, while coking coal consumption decreased by 2.8 percent and the other industrial sector declined by 3.7 percent. The commercial and institutional sector, that had been called the ?residential and commercial? sector prior to 2008, declined by 0.6 percent in 2008. It is the smallest of all the coal-consuming sectors. (Note: All percent-age change calculations are done at the short-tons level.) U.S. coal exports were significantly higher in 2008, while coal imports decreased during the year. Total coal stocks increased in 2008, as some consumers added to their stockpiles. The coal synfuel industry, which grew throughout most of this decade, disappeared from the scene due to the expiration of the available federal tax credits at the end of 2007. The decline in coal consumption during the year was the consequence of slowing domestic economic growth, particularly in the latter half of the year, combined with the weather conditions in 2008, resulting in lower demand for electricity. Preliminary data show that total generation in the electric power sector (electric utilities and independent power producers, including useful thermal output) in the U.S. decreased in 2008. Coal-based generation also decreased, resulting in a 3.2-Mt (3.5-mil-lion st) drop in coal consumed in the electric power sec-tor. Coal use in the non-electricity sector decreased by 3.3 percent to a level of 72.6 Mt (80.1 million st). The international coal markets in 2008 were the driv-

Jan 1, 2009

By D. Nutakor

The ability of computers to create synthetic representations of the real world in virtual reality offers a number of opportunities to enhance training methods used in the mining industry. Unfortunately, the training effectiveness of virtual reality systems currently used in the mining industry has received only limited testing. Miner Simulation (MinerSIM), an augmented reality system with integrated hypermedia suitable for training underground miners in the basics of using a jackleg drill to install rock bolts in a virtual mine environment is in its evaluation process at the University of Missouri-Rolla Experimental Mine. This paper discusses evaluation methodologies of the MinerSIM system, which consists of experimental and control groups with control students learning via traditional lecture and text formats. Preliminary results from usability tests of the first part of MinerSim, which is an online tutorial on underground rock bolting, are presented.

Jan 1, 2008

By Merih Celasun

The literature in operations research centered on mineral exploration has been comparatively limited in view of the significant implications of mineral discoveries upon the national economies in general and mineral industries in particular. Much of what has been published is of somewhat unsure academic nature, indicating to a certain extent the scarcity of industrial applications. Mineral exploration activities present quite difficult operational and conceptual problems. The purpose of this paper is to discuss the principal characteristics of decision problems encountered in planning an exploration program, to indicate an optimization approach to a certain class of allocation problems, and to suggest directions for future research effort.

Jan 1, 1962

By Richard A. Brown

The direct precipitation of uranium with hydrogen peroxide has been known since 1877. Commercial use of the process began in the 1960's. During 1967 the Bureau of Mines assisted the Climax Uranium Co., Grand Junction, Colorado in the development of a uranyl peroxide precipitation process to control a molybdenum impurity problem (1). Atlas Minerals, Moab, Utah has used hydrogen peroxide to control vanadium and sodium levels in their uranium concentrates since 1969 (2). Recently, the use of hydrogen peroxide by the uranium industry has grown, particularly since the increased demand for uranium has led to the processing of low grade ores. Impurities present in low grade ores can be concentrated with the uranium during milling and will substantially complicate the refining of uranium yellowcake concentrates. Consequently, commercial nuclear fuel processors have imposed stringent specifications and penalties to control these impurities. The ability to produce a pure uranium yellowcake can eliminate penalty or reprocessing costs. Hydrogen peroxide precipitation of uranium is specific and quantitative, producing a very high purity product.

Jan 1, 1980

By J. Hanna, H. R. Gonzalez

Four Ca-bentonitic clays from Alabama were evaluated for use in diammonium phosphate (DAP) or urea ammonium nitrate (UAN) fertilizer suspensions. The viscosity and gel strength of suspensions prepared with different proportions of a Western bentonite clay and sodium-exchanged Alabama clays were measured as a function of clay content and dispersant concentration. The results obtained suggested that three of the Alabama Ca-bentonites would replace about 40% of the more expensive Western bentonite in UAN and DAP fertilizer suspensions. The performance of the Nu-modified clays, prepared according to the Tennessee Valley Authority soda ash method, was as good or even better than those observed for the Mg-, NaIMg- or K-modified clays. The TVA clay modification procedure appears to be reliable and cost effective.

Jan 1, 1991

By A. Wright

Gold Fields Mining Corporation is presently evaluating gold mineralization beneath thick, wet alluvium at the Chimney Creek Project, Nevada. Contamination of reverse circulation samples has been visually apparent since drilling began in the area. Tests have shown that, while contamination can affect assays, reverse circulation holes appear to define mineralized zones almost as well as the diamond drill holes. To improve reverse circulation sample integrity several techniques were tried including a stiff-mud injection system but with limited success. Diamond core drilling continues to be used in conjunction with reverse circulation drilling to further delineate the mineralization.

Jan 1, 1991

By A. H. Shapiro

A decanter centrifuge of novel design was developed for the dewatering of fine-solids slurries having micron-range particles that form paste-like, flowable, hard-to-dewater cakes. The design combines a compound beach with a cake-flow control structure that allows expressed liquid from the cake in the dry beach region to be returned back to the liquid pool while maintaining high solids throughput. In order to provide optimal performance with various operating parameters (feed rate, centrifugal gravity, pool, differential speed, concentration of feed solids, and different slurry types), the cake-flow control is adjustable. The second part of the beach is preferably at zero angle. Tests showed that the new design allows increases in both solids dryness and solids throughput.

Jan 1, 2001

By S. L. Huang, J. D. Rockaway, N. B. Aughenbaugh

Shale has long been recognized for its tendency to swell when exposed to the atmosphere. Interaction of moisture with exposed shale strata can cause serious ground stabi1ity problems, since the initial strength of a shale is reduced if the material is sensitive to moisture variations. In this paper, the authors present a classification system to estimate the response of swelling generated within shales. This characterization of the swelling potential is based upon plasticity, susceptibility to moisture, mineralogical constituents of clay size particles, and fabric. Use of this classification system in conjunction with other existing rock properties tests will provide data for more rational engineering design.

Jan 1, 1986

By J. O. Craig Imrie

Mine operations are being squeezed to do more with less. This is not new. But, where do mine operators turn for the next stage of improvement? Many have waged strong wars on the cost reduction front and cut back staff to the bone, yet need more improvement to remain competitive. This paper will outline an approach which a few leading operators have taken. Following the footsteps of manufacturing's view of supply chain management and basic quality management they are reaping the benefits of taking a more holistic process view of their operation. This paper presents summaries of three companies' approaches and the impact which is being felt on the bottom line.

Jan 1, 1999

By Paul Culvenor, Brad Gyngell

Ensuring effective management of contractual processes is essential for maintaining profitability and operational efficiency in mining. However, due to limited capacity and resources, sites often struggle to manage these processes effectively, leading to oversights and financial losses. Recent advancements in Artificial Intelligence (AI) offer promising solutions to these challenges. Large Language Models (LLMs), like those powering ChatGPT, now enable machines to understand unstructured data like contracts. These can therefore be applied to address these challenges by taking some of the heavy lifting off of humans. In this paper, we analyze a real-world case study of the application of LLM tools for preventing a $400k contractual issue on an underground gold mine in Western Australia. We provide a gap analysis of the failure modes in existing processes that led to the issue. We then describe the application of LLM tools to flag it early and facilitate a collaborative solution between the operator and the supplier. This includes a comparative analysis of base case vs LLM case to evaluate the impact on project cost and time. Finally, we discuss how the integration of AI can foster improved relationships between clients and contractors across a broad range of potential contractual applications, allowing the time required for collaborative and proactive problem solving.

Feb 1, 2025

By O. Alvarez-Campos

Two porphyry copper orebodies, the North and Central MM orebodies, have been found through regional and structural geologic works, about 5 Km south of Chuquicamata, under a gravel bed of approximately 100 m and in the west side of the West Fissure. The mineralization is emplaced in a coarse granodioritic porphyry, predominantly with sericitic alteration. In the North MM ore-body, with 200 million metric tons of 1.0% Cu, the mineralization is mainly chalcopyrite, bornite, digenite and molibdenite. In the central MM orebody, with 700 million metric tons of 1.3% Cu, there are large veins of enargite, chalcocite and bornite, the last one increasing in depth, separated by chalcopyrite and pyrite zones; in these veins there are interesting gold and silver values. Both orebodies have an upper enrichment of chalcocite and covellite, with pyrite envelope. According with these characteristics, the MM orebodies could he the upper part, with sericitic alteration, of the Chuquicamata porphyry copper system, displaced by the West Fissure system movements, but we couldn't eliminate the possibility that MM can be a new orebody, different of Chuquicamata.

Jan 1, 1993

By D. Zaharaki

In the present experimental study the geochemical stability of inorganic polymers was studied by immersing them in various solutions (distilled water, seawater and 0.5N HCl) for a period of 7 months. Inorganic polymers were synthesised by mixing ferronickel slag with kaolinite, potassium hydroxide and sodium silicate solution. The cement like paste was heated at 80 °C for 48 hours and left for curing at room temperature. Their structural integrity was assessed by compressive strength testing after subjection to freeze-thaw cycles as well as high temperature heating. XRD studies were carried out in order to identify new formed phases and provide useful information regarding the progress of the mechanisms involved.

Jan 1, 2008

By S. Veeramasuneni

The recent nonequilibrium electrophoretic mobility measurements by laser-Doppler electrophoresis coupled with the stability and prevalence of collector colloids in soluble-salt flotation systems suggest that the selective flotation of alkali halides is due to the adsorption of oppositely charged collector colloids by heterocoagulation. Previously reported flotation results confirm this surface charge/collector colloid adsorption model. These results also indicate that the sign of the surface charge has a significant effect on the extent of particle dispersion/aggregation. In this regard, the nature of such particle interaction forces at high ionic strengths are examined to improve our understanding of these systems. Atomic force microscopy (AFM) is now being used to directly measure the interaction forces responsible for the stability of these alkali halide aggregates observed in optical microscopy studies. Results from this study indicate that, while repulsive hydration forces exist between similarly charged hydrophilic particles, attractive forces exist between oppositely charged hydrophilic particles in high ionic strength solutions.

Jan 1, 1999