Search Documents

By Bruce A. McKinstry

Introduction For many major mining projects the time frame from initial planning to production can be measured in decades. Hecla's Silver Shaft project, scheduled to go into production by the end of this year, includes a complete surface facility, shaft with an ultimate depth of 2.4 km (7,700 ft), complete ore pass and loading pocket system, and 610 m (2,000 ft) of development drifting and stope preparation. The project was conceived in the fall of 1979, and the duration of a mere four years from conceptual engineering to production is testimony to what can be accomplished when a mining company and a contractor work as a team rather than developing into two warring camps, as often happens. Engineering In 1979, Hecla Mining Co. awarded a contract to J. S. Redpath Corp. to perform feasibility investigations and design engineering related to a proposed new shaft facility at the Lucky Friday Mine. The Lucky Friday, in Mullan, ID, is a major producer of silver, as well as significant quantities of lead and some zinc. In late 1979, stoping was in prog-

Jan 10, 1983

By R. H. Grau

This Bureau of Mines report describes methane liberation trends from all U.S. coal mines liberating over 100 Mcfd (100,000 cfd) (2.8 Mm3/d). Detailed are results from the latest Bureau survey performed in 1985 and shown are mine and company name, location, coalbed and methane liberation quantity. The report shows that in 1985, there were 180 mines producing more than 100 Mcfd (2.8 Mm3/d) and the total quantity of methane liberated by these mines was 303,900 Mcfd (8,605 Mm3/d). This data is compared with previous studies performed in 1971 , 1973, 1975, and 1980. From 1971 to 1985, there was a 10% decrease in the number of mines liberating at least 100 Mcfd (2.8 Mm3/d) but there was a dramatic 34% increase of liberations from these mines. The increase seems to be caused by new mines being developed in deeper, gassier coalbeds, particularly in Alabama. Likewise, in comparing the ten highest liberating mines in 1975, 1980, and 1985, an increase in methane liberations each year was experienced. The report classifies mines by three levels of liberations: greater than 100 Mcfd but less than 500 Mcfd (2.8 to 14 Mm3/d); 500 Mcfd to 1 ,000 Mcfd (1 4 to 28 Mm3/d); and greater than 1,000 Mcfd (>28 Mm3/d). It was found that 87% of liberations were from mines producing over 1,000 Mcfd but these accounted for only 38% of all the mines in the study.

Jan 1, 1987

By Charles E. Mergentime, J. Marshall Dean

Mergentime/Loram's extension of the Washington, DC Metro Subway System includes construction of dual 1,770-foot tunnels in soft ground, a crossover structure, a fan structure and pumping station, and other related work. This paper describes the overall construction requirements of the Contract, including subsurface conditions; Mergentime's value engineering of the tunneling and compressed air contract requirement; selection of the tunnel boring machine and backup equipment; installation of the compressed air plant; the manufacture, use and evaluation of the tunnel liners; and the tunneling performances during construction of the first tunnel.

Jan 1, 1985

By Mahmoud Sepehrmanesh, Verya Nasri, Maziar Partovi

"This paper presents an assessment of the impact of tunneling and its associated risks on pile foundations located in the influence zone of tunneling operation. Tunneling in proximity of pile foundations introduces deformations in piles and in turn induces additional axial and bending forces. In modern mechanized tunneling, ground convergence is controlled through balancing the earth pressure at the tunnel face as well as applying pressurized bentonite through the shield. Reducing ground deformation can consequently lower the additional deformations and forces developed in the pile foundation and lessen the associated construction risk. In this paper, comprehensive detailed finite element modeling was performed to quantify the effect of the different parameters on induced forces in piles. Finite element models took into account the nonlinear behavior of soil and pile-soil interface. The modeling results are of practical importance in risk evaluation of tunneling in vicinity of pile foundations. INTRODUCTION Tunneling operation in congested urban areas becomes more frequent as demand for further utilizing underground spaces grows. In urban settings, it is not uncommon for tunnel designers to plan a tunnel route in close proximity to other structures to satisfy other competing objectives like raising the alignment to reduce excavation volume. Setting the alignment close to existing structures increases the risk involved in the project. It is the responsibility of the designer to thoroughly identify, assess, and mitigate all design risks involved. In this paper, we focus on the aspects involved in tunnel construction in proximity to existing pile foundations. Tunnel operations introduce deformation in the soil mass. Consequently, a pile located within deformation zone experiences extra forces as a result of the imposed deformation. The developed forces and bending moments can be in orders comparable with the pile capacity depending on the relative horizontal proximity of the tunnel and the relative depth of tunnel with respect to the pile length."

Jan 1, 2016

By M. R. Peterson, C. R. Ferguson, T. H. Jeffers

The ability of microorganisms such as yeast, bacteria, and various aquatic flora to sorb metals from dilute aqueous solutions is well documented. Although microorganisms have significant potential in decontaminating waste waters, techniques and equipment suitable for bioassisted decontamination are limited. The Bureau of Mines has investigated the use of microorganisms immobilized in porous polysulfone beads for extracting toxic and heavy metals from dilute waste streams. The minus 8- plus 12-mesh beads were fabricated from high-density poly- sulfone dissolved in dimethylformamide (DMF). Dried, thermally killed yeast, algae, duckweed, xanthan gum, and alginates were blended into the polysulfone-DMF, and spherical beads were formed by injecting the mixture into water. Microscopic analysis revealed microorganisms immobilized within the bead pores. The beads had excellent handling characteristics and were tested in stirred reactors, fixed bed columns, and fluidized bed columns for their ability to remove metal contaminants from several waste waters. The effluents resulting from these waste waters met or exceeded the National Drinking Water Standards for cadmium, copper, manganese, and zinc. Other heavy metal contaminants readily sorbed by the beads included arsenic and mercury. Elution of metal values from the beads was accomplished using dilute nitric acid or sodium carbonate.

Jan 1, 1989

By B. Rao Pothini, Julio H. Thaler, W. L. Finlay

The White Pine room-and-pillar mine started in 1955 from a suboutcrop, down gentle dips, and with a competent sandstone roof. As mining depths increased, extraction decreased 1% every 35 feet. Moreover, roofs became shaly and less competent, and regions of high fault and joint densities, sometimes with and some- times without high lateral stresses, increased the tendencies towards roof falls. Instinctive reactions towards narrower openings did not alleviate the problem. Careful consideration of rock mechanics principles culminated in the development of two variants to the conventional room-and-pillar mining system based on the concept of stress relief through load deflection. The two systems-EquiAdvance Cave, and PressureArch Panel Mining-are complementary. The objective of the former system is to provide relief from lateral stresses through advance caving and in the process also to achieve higher extraction at depth. Where surface subsidence cannot be allowed, the alternative PressureArch Panel concept is utilized to provide stress relief and moderately high extraction ratio. Both systems have been under trial for over three years and, together, produced over three million tons of copper ore. These two systems, and their production test results to date, are described.

Jan 1, 1977

By S. N. Groudev

A process for the combined chemico-biological removal of iron present as oxide minerals in different mineral raw materials (quartz sands, kaolins, clays, etc.) was developed. In the process, mineral raw materials are leached at about 90 °C with lixiviant containing microbially produced oxalic and hydrochloric acids. The leaching is carried out in mechanically stirred acid-resistant reactors for periods of from 1 to 6 hours, depending on the iron content and the forms of iron in the raw materials being leached. The iron contents of some sands treated by this method were lowered from levels that were in the range of 0.035% to 0.088% Fe2O3 to less than 0.012% Fe2O3, making them suitable for the preparation of high-quality glass. The iron contents of different kaolins were lowered from levels that were in the range of 0.65% to 1.49% Fe2O3 to levels in the range of 0.44% to 0.75% Fe2O3. As a result, the whiteness was increased from values of 55% to 87% to values of 86% to 92%. The iron content of clay was lowered from 6.25% Fe2O3 to 1.85% Fe2O3, and this increased the “fireproofness" of the clay from 1,670°C to 1,750°C. A similar process was used for the leaching of aluminum from aluminosilicates, mainly clays and kaolins. However, in this case, the microbial fermentation fluid containing citric acid was acidified by means of sulfuric or hydrochloric acid or by means of different mixtures of mineral acids. For enhancing aluminum solubilization, the aluminosilicates were heated before leaching at 600° to 650°C for 1 to 2 hours. Over 90% of the aluminum present in different clays and kaolins were leached within 3 to 6 hours. "Silicate " bacteria related to the species Bacillus circulans were used to leach silicon from low-grade bauxite ores containing aluminosilicates as impurities. The bacterial action was connected with the degradation of the mineral structures (by means of microbial metabolites such as organic acids and exopolysaccharides), as well as with the selective separation of the rich-in-aluminum fine fractions, which were retained by the mucilaginous capsules of the bacteria. The solid residues after treatment were characterized by higher values of alumina and silicon module (A1203: SiO2 ratio), and they were suitable for processing by means of the Bayer process for recovering aluminum. The bending strength and other ceramic properties of kaolins were improved by contact with well-developed cultures of "silicate" bacteria. The improvement was caused mainly by bacterial metabolites (exopolysaccharides) that acted as resins during drying.

Jan 1, 2000

By Roe-Hoan Yoon

INTRODUCTION In 1960, coal accounted for 49% of the world energy consumption, an amount that was reduced to 29% in 1973 because of the availability of cheap oil. At that time, it seemed that oil would remain available for a long time in unlimited quantities. However, this situation changed drastically in 1973/74 when a series of closely spaced price increases from $3 per to $12 per bbl by mid-1974 hit both industrialized and developing countries. Another sharp price increase in 1979/80 to the $34 to $38 per bbl level also hit the world economy hard and, at the same time, set in motion powerful technology development forces for increased coal utilization. At this point, the price of coal was approximately $1.50 per MM Btu, while that of oil approached $6.00 per MM Btu. This huge price differential offered an incentive for developing new coal technologies including liquefaction, gasification, fluidized bed combustion, coal-water mixture (CWM), etc. The CWM technology was of particular interest to the utility industry, which consumes more than 80% of the coal mined in the US for power generation. In this technology, a powdered coal is mixed with water to produce a stable slurry that can be stored for an extended period of time without settling and is readily pumpable. Various reagents in the amount of approximately 1% by weight of the coal are added to inhibit sedimentation during storage and to reduce the viscosity for atomization in burners. The coal loading is in the range of 50 to 80% solids, depending on the particle size and its distribution. With very fine particles, it is difficult to increase the coal loading above 50%, and a binomial distribution helps increase the coal loading. The presence of water consumes a relatively small amount of the heating value of the coal during combustion; for a coal-water slurry containing 30% water, less than 5% of the calorific value of coal is usually consumed due to evaporation. The major advantage of burning coal as a slurry is that many of the oil-burning furnaces can be converted to coal-burning with a minimum retrofit cost. Considering the substantial price margin between coal and oil, the pay- back period for retrofit costs can be relatively short. Nevertheless, the retrofit cost can be further reduced if low-ash coals are used as feedstocks for CWM; there will be savings in the capital cost of installing bag filters or electrostatic precipitators that are designed to remove the ash from the combustion gases. Furthermore, the use of low-ash coals can minimize derating of boilers because the velocity of the combustion gases can be maximized without creating erosion

Jan 1, 1991

Information Technology has addressed those problems unique to senior management in the mineral industry. In general, these problems are those concerned with decision-making. Peter Drucker in his discussion of making effective decisions identifies five phases: (1) define the problem, (2) analyze the problem, (3) develop alternate solutions, (4) decide the best solution, and (5) convert the decision into effective action. The scope of the chapter by Guernsey addresses the first three phases which provide input to the decision-maker. The decisions to be made relate, in most instances, to the economics related to a mineral property or process. Computer models have been designed to generate these economic and financial evaluations. No one model is appropriate to the solution of all management's problems. In this chapter several applications are identified and summarized; a model for the economic evaluation of a mineral property is described in greater detail. The implementation of such models is dependent on the unique needs of management.

Jan 1, 1979

By L. Cui

X. Huang (1997) recently suggested a poroelastic model for simulating the hydraulic fracturing breakdown pressure. His paper began with a discussion questioning Haimson and Fairhurst's (H&F) model. He claimed that the H&F model failed to lead to the Hubbert and Willis (H&W) model as[ a --> 0.] Huang also tried to explain why the H&F model could only work for special types of rock conditions. He pointed out that one possible reason could be that the Terzaghi's effective-stress concept had been adopted. The H&F model (Haimson and Fairhurst, 1969) was derived under the conditions that the borehole wall is fully penetrated (pp = pi) and a drained state is realized (steady pore-pressure field). Cui et al. (1997a) demonstrated that, under drained conditions, the total stresses in the penetrating poroelastic model (identical to the H&F model) degenerate into their counterparts in the elastic model (identical to the H&W model) as [a -- 0.] However, the effective-stress conditions are different for both of these models, because different pore-pressure conditions at the borehole wall were adopted. In the H&W model, p = po was assumed, i.e., the pore pressure field is not disturbed; but pp = pi was assumed in the H&F model. Assuming that Terzaghi's effective-stress controls tensile failure (that was the hypothesis adopted in both the H&F and the H&W models), only the following two special drained poroelastic cases may degenerate into the H&W model for very small a: • when the pore pressure at the borehole wall remains at the same level as the virgin pore pressure for a penetrating model and when the borehole wall is simply impermeable (i.e., the nonpenetrating model, Cui et al., 1997b). Therefore, simply setting a = 0 in the H&F model generally does not lead to the same problem described by the H&W model. On the other hand, when the porepressure boundary conditions do not correspond to the ones in the H&W model, a degeneration of the poroelastic model to the H&W model as [a – 0] should be questionable. The pore pressure at the borehole wall is generally dependent on the injection-fluid pressure and the penetrating conditions at the borehole wall, such as the existence of a filter-cake. For an impermeable wall, pp is independent of Pi, and it is basically an unknown [(how¬ever, pp -- po as t --oo).] For a fully permeable wall, pp is the same as Pi. Between these two extremes, pp should be a function of p; and the permeable condition of the borehole wall, which may be dependent of the leak-off coefficient cf. (the range of cf is from 0 to 1). Theoretically, for a rock with low permeability, a penetrating borehole wall is still possible. For saturated porous materials with very low values of a, poroelasticity shows that a pore pressure will be built up due to the stress concentration subjected to a nonhydrostatic in situ stress field (Cheng et al., 1993). This phenomenon is known as the Skempton effect. The variation of the pore pressure may be evaluated by [AP = 3 B(A rr + 06ee + A (Y,,)] (1) where B is the Skempton pore pressure coefficient. This pore pressure variation dissipates as time increases (it is totally gone as the drained state is approached). The rate of the dissipation mainly rely on the permeability of the formation. The dissipation is very slow for tight formations because their permeability is very low, and it is fast for rocks of high permeability. According to our analyses, the time period for this process could be from seconds (for sandstone's) to a couple of days (for stales). One possible reason that the H&C model did not agree well with the experimental results for rocks with low permeability might be that the time interval between the application of the loading and the fluid injection had not been long enough for the dissipation of the Skempton effect. The effective-stress law basically defines how much pore pressure contributes to the total stress. The difference between Terzaghi's effective stress and Biot's effective stress is that 100% of the pore pressure contributes to the total stress in Terzaghi's definition, while only a certain portion of the pore pressure ((ap) goes to the total stress in Biot's definition. Therefore, when the pore pressure at the boretole wall (pp) is determined according to Biot's effective-stress law, app in the total tangential stress is attributed to the pore pressure. In other words, Terzaghi's effective tangential stress is expressed

Jan 1, 1999

By Peter Keppler, Stephen D. Bundy

"Due diligence" is a review or audit of a facility or business to assess and quantify risks and operating status before an acquisition. Due diligence findings can be used to negotiate the price, general terms, and indemnification provisions in the purchase and sales agreement. In addition to assessing out- standing liabilities, necessary capital improvements, and the adequacy of operating budgets, due diligence should include "nontechnical" considerations, such as local community acceptance and relations, and the effect on the company's public image and operations. This paper will discuss how these considerations can be addressed in the due diligence process and factored into the transaction. Also, innovative means for risk reduction and risk transfer, during and after the transaction, will be discussed.

Jan 1, 2001

By Charles D. Litton, Margaret R. Egan

In order to reduce the number of nuisance fire alarms in underground mines that use diesel-powered equipment, the U.S. Bureau of Mines has developed a diesel-discriminating fire detector (DDD). It was designed to discriminate between smoke produced by a fire and the smoke-laden exhaust of a diesel engine. Welding and cutting with arc or flame can also produce combustion products capable of triggering nuisance alarms. In this report, the response of the DDD to the emissions from diesel exhaust, arc welding, and flame cutting are compared to the response of conventional smoke and carbon monoxide (CO) detectors. The data show that when the DDD is set at an alarm threshold of 0.05 v, it will reliably detect a developing conveyor belt fire while remaining insensitive to other sources of nuisance combustion products. The alarm times of the three types of detectors were also compared. The DDD alarmed first in response to a smoldering conveyor belt in two of four experiments.

Jan 1, 1992

By Kerry M. Masson

Perhaps the hottest item on the agendas of most state legislators this year is the state budget. The main question: Where will all the dollars come from to finance health care programs, state jobs, unemployment compensation programs, and on and on? This is especially so since people are out of work, business bankruptcies are up, sales are down, and incoming revenues from some sources have decreased or dried up. A sure bet is that state taxes will be increased in some form or another. The mining industry could face increased income taxes, property taxes, severance taxes, or even a host of new taxes (if the state does not already have them) like a gross receipts tax, investment tax, or tax on revenues made outside state borders. That's bad news for an already depressed industry, even though increased taxes may be the least of the industry's worries in the current economic climate. While reopening existing mines and developing most new mineral projects depends primarily on higher commodity prices, new taxes still could pose long term concerns for mine project development. Just how mineral tax law impacts a project is not easy to figure. It involves a complex set of calculations based on interpretations of numerous federal, state, and local tax laws that change almost annually. At best, projections of tax effects for the life of a mine are educated guesses. At the same time, projections are necessary to evaluate the economic feasibility of a mineral project. At a recent Technology Transfer Seminar, the US Bureau of Mines introduced a computer software program designed to evaluate the feasibility of a mineral project and to determine the tax effects on the project's discounted cash flow rate of return (DCFROR). The program, called MINSIM, began in 1967 as a 200-statement FORTRAN II program for evaluating a hypothetical large-scale open-pit gold mine. This single-commodity oriented program employed discrete simulation techniques and a continuous DCFROR was used to measure the effect of changes in revenues and costs. Over the past 15 years, MINSIM has developed into a program 70 to 100 times larger than the original. Basically, it will analyze costs and parameters specific to an identified deposit, then determine the DCFROR. Or by using a specified DCFROR, it will determine the primary commodity price required to attain that specified rate of return. MINSIM, which is explained in detail in this article, is available from the Division of Minerals Availability, USBM free of charge. Written in FORTRAN IV, it comes on punch cards or magnetic tape and is compatible with most major computer systems. The MINSIM Program The main objective of any freeenterprise mining venture is to make a profit. To determine profitability of a given project, alternate methods of operating and financing must be evaluated. That is the purpose of MINSIM. While there are a number of methods of evaluating the economic profitability of a mining project, MINSIM uses the Discounted Cash Flow Rate of Return (DCFROR) method as its major criterion because DCFROR considers the time value of money and gives the truest measure of profitability. One disadvantage is that the calculations are deposit oriented. In other words, MINSIM analyzes only those costs and parameters specific to the deposit. It cannot be used to evaluate the overall corporate picture. The program is designed to simultaneously handle five different commodities and a leach operation for any type of mining project. For example, analysis of a coal project would include only one commodity-coal at the mine mouth. Analysis of a copper operation might include numerous commodities-from the raw material to the refined product. Input MINSIM considers capital investment-recoverable exploration, acquisition, and development costs; depreciable capital investments such as mine plant and equipment, mill plant and equipment, and infrastructure costs; all general and commodity specific operating costs; and the cost of alternate financing methods. The program has the capacity to incorporate different types of depletion allowances, numerous commodity-dependent severance taxes, variations of property taxes, and many methods for calculating state or provincial taxes. There are even many different ways to calculate federal and national taxes. The capacity to handle tax variations is generated from an internal subroutine in the program called the "open file." The user can reconstruct, customize, or evaluate any kind of tax desired. Outputs Given this kind of capacity for numerous input parameters, MINSIM is capable of the follow¬ing major outputs:

Jan 3, 1983

By R. Gong, R. Bhaskar

A coal mine study was conducted to evaluate the effectiveness of a compressed-air, foam spray system installed under a continuous miner boom and directed to cover the pan and the gathering arm. The study's objectives were to evaluate the foam, underboom sprays' effect on: • the respirable dust concentration in the ambient air, and • the quartz concentration in the airborne, respirable dust. The foam generation and delivery system's engineering design is described in the paper, followed by descriptions of the mine and the dust sampling strategy. The data were analyzed to study the foam's effects on respirable dust and quartz concentrations at the continuous miner cab, the face return and the intake. The data indicate reductions in the dust's quartz content, ranging from 19.7% to 64.6%, in eight of 11 comparisons of the foam vs. no foam cuts. In addition, airborne intake dust reductions were observed in eight of 11 comparisons.

Jan 1, 1993

By W. S. Weldon, R. M. G. Machunter

The use of spiral separators for the beneficiation of fine coal typically in the size range - 2+0.lmm is now well established process technology. Developments during the mid 1980's resulted in the production of cost effective, efficient large diameter coal spiral separators. Recent developments and research have been geared to optimise metallurgical performance, materials handling and equipment geometry of large diameter coal spiral separators.

Feb 24, 1997

By Donald R. East

The impacts of the economic storage or disposal of mill tailing wastes are becoming more important to the mining industry as environmental regulations become more demanding. Mill tailings have long been considered the stepchild of the extraction process and have not, until recent years, been treated as a separate entity of the mining and milling process with distinct and complex physical and chemical characteristics. As a waste product, the economic value of mill tailing is usually very small whilst economic and the environmental liabilities can significant. be Disposal of tailing is commonly identified as the single most important source of environmental impact for many mining projects.

Jan 1, 1990

By Michael Karmis, Emily A. Sarver, Ellen S. Gilliland, Leigh-Anne H. Krometis

"Public engagement is increasingly important in ensuring the success of projects related to energy development, particularly with regard to issues of environmental protection, public health, and socio-economic impacts. This is due to concurrent trends in public behavior, including a rise in public interest in these projects that is not matched by a rise in science literacy, and increasing organization and participation of the public through social media, citizen science, and grassroots initiatives. In recent years, several high-profile incidents have demonstrated that when public concern is ignored or met with a passive response from industry, it can rapidly grow into organized opposition that negatively impacts or wholly derails a project. Engaging, listening to, and educating stakeholders during early planning and development phases are therefore essential to earning credibility and trust. Moreover, maintaining two-way lines of communication throughout the lifespan of a project demonstrates social responsibility and facilitates cooperation, acceptance, and even support from communities and others. Positive experiences with specific projects at a local, community level can influence the larger public opinion of an entire industry sector. This paper presents cases studies of public engagement related to shale gas development (including hydraulic fracturing and pipeline construction), mountaintop removal mining, and management of mixed-use watersheds near surface mining operations. The experiences highlighted in these case studies are used to draw best practices of public engagement for sustainable energy development.Introduction Within the scientific research community, the importance of public engagement has gained increasing recognition. In a 2007 article in Nature, medical researcher, Patrick Taylor, stated that public engagement has both “gone viral” and “gone global” and has the ability to make real impacts to research (Taylor 2007). Nancy Baron, the science outreach director for COMPASS, an organization providing communications training for scientists, provides further evidence for the increasing focus on engagement, including shifting attitudes observed during her own experience as a communications coach and documented in surveys, the recent inclusion of communication and engagement activities in academic tenure review, and the surge of workshops, materials, and other resources available on the subject (Baron 2016). In addition to COMPASS, a number of organizations and institutes have been developed to train scientists for communication and engagement with the public, perhaps most notably the Alan Alda Center for Communicating Science at Stony Brook University, and academic fellowship programs, such as the Leopold Leadership Program at Stanford University and the Wilburforce Fellowship Program, have been established for the same purpose."

Jan 1, 2017

By P. M. Solozhenkin

The proposed technology of antimony calcine processing includes ferrochloride leaching of calcine, reducing solutions, hydrolysis of hydrochloride solutions with antimony oxochloride isolation, synthesis of antimony trioxide by SbOCl neutralization and its drying, regeneration of hydrolysis solutions. The optimum parameters of separate stage of process has been determined and the chemical character of process has been given. During the leaching of calcine we succeeded to transfer 92.16- 95.66% antimony to solution. On the worked out sheme we attained recovery of antimony to antimony trioxide near 90 .5% Antimony triozide contains 99.5% Sb2O3. The composition of sinter burdens for pigments preparation "Naples Yellow" different colours from brightly-yellow, yellow and lightly yellow has been proposed. Three-sulfuretted antimony-antimonic cinnabar have been prepared by precipitation of antimony solutions by potassium sulfur-bearing solution. The prepared compounds correspond to inorganic pigments for artistic paint. The amorphous antimony-ferrous black we prepared by aluminium cementation of hydrochloric antimony solutions. The ferrous black were used as artistic paints and for coating of metals by antimony.

Jan 1, 1995

By A. R. Wagner, E. Berkman

The use of high-resolution seismic surveys in coal exploration and mine development is becoming established as a standard technique in the industry. Their most significant contribution is in the effectiveness of reducing the number of core holes needed to understand the complex geological nature of coal by identifying geologic faults and mapping coal seam continuity and relative coal thickness. With these goals in mind, a high-resolution seismic survey was conducted in 1980 in the Wasatch Plateau coalfield of Utah. As a result of the success of this initial survey, numerous additional surveys have been performed over the past six years.. The interpretations of these subsequent surveys have led to the location of faults, fluvial channel sandstones, and coal thickness trends. This paper presents a review of high-resolution seismic technology as applied to coal exploration followed by three case histories, two of which illustrate the utility of the technique related to coal thickness determination and faulting and one that serves as an example of pitfalls in interpretation.

Jan 1, 1987

By C. -G. Zhang

This paper presents the results of a study on cellular acclimation of Acidithiobacillus ferrooxidans to sulfur biooxidation in terms of cells growth and changes in surface properties and morphologies of both cells and sulfur particles. The results showed that A. ferrooxidans cells were grown faster and demonstrated higher concentration in the soluble thiosulfate substrate than in nonsoluble hydrophobic S0 substrate. The results showed that A. ferrooxidans cells acclimated to the sulfur biooxidation by actively expressing some extracellular polymers substance and maybe some outer membrane proteins that modified the surface properties of both sulfur particles and the cells themselves. In addition, the results showed that the A. ferrooxidans cells were able to dynamically adsorb to or desorb from the surface of sulfur particles. The cells aggregating onto the S0 surface enhanced the use of S0 substrate by the bacteria cells. This mode may be one of the most important characteristics for the better growth and propagation of the cells in solid sulfur-containing media.

Jan 1, 2009