Search Documents

By Viggo C. Bertelsen, David G. Hammond

LOCATION AND EXTENT OF BART TUNNELS The San Francisco Bay Area Rapid Transit District (BART) during the past six years has become the Owner of 23.5 miles of single-bore tunnels. The tunneling experience gained while working closely with our Engineer and Contractors in the design and construction of these major transit facilities provides a basis for our "Owners" viewpoint. The 23.5 miles of tunnels are divided into two categories. Fifteen and one-half (15-1/2) miles of tunnels were constructed in soft ground underlaying the downtown areas of San Francisco, Oakland and Berkeley. Eight (8) miles of tunnels were built in "hard ground" in the hills separating Oakland and Berkeley from Contra Costa County and in the San Francisco hills on the Mission Line. Location of tunnels within the BART system are shown on Figure 1. The tunnels comprise 15.7% of BART's 75-mile dual track system. Their 176 million dollar costs (excluding rail, electrification or ventilation features) are 12.4% of the system's total estimated cost of $1.4 billion. The tunnels constructed in soft ground were shield and boring machine driven with ground support provided by steel liner rings. The exterior diameter is 17 foot, 6 inches in the majority of tunnels; however, on two tunnels with a 500 foot radius of curvature, the diameter was 18 feet. BART awarded 14 contracts for soft ground tunneling. The work was accomplished under free air or compressed air depending upon the ground water and soil conditions, safety requirements, and considerations for protecting adjoining property from damage either from the de-watering operations or settlements due to excavation. The tunnel bores, except on curves, were normally parallel being spaced at 32 foot centers on the Mission

Jan 1, 1997

By W. H. Langer

Natural aggregate is the number one non-energy mineral resource in terms of value and volume and is a necessary commodity for sustainable communities. While aggregate is a non-renewable resource, supplies are nearly inexhaustible on a global scale. Natural aggregates have characteristics that differentiate them from most other mineral commodities: a high number of potential extraction sites, a high volume to value ratio, significantly different set of potential environmental impacts, and regional importance combined with a narrow economic transportation radius. Because of these and other differences, resource management policies for aggregates should differ from ?general? mineral resource policies, even though the end goal is the same for both ? ensuring sustainable resource management. To achieve the goals of sustainable aggregate management each stakeholder ? government, industry, the public, and non-governmental organizations ? will need to accept certain responsibilities, one of the most important of which is to become informed about natural resource issues. Sustainability is about making trade offs among competing objectives, and people disagree about the appropriate balance among the goals of economic prosperity, social equity, and environmental health. One of the primary purposes of mineral indicators is to provide information to decision makers and the public so as to ensure that the public debate about policy choices is grounded in fact. We identify the unique aspects of aggregate resource management and introduce the concepts of sustainable mineral resource management. We then present mineral indicator sets for aggregate resources from Italy, the United Kingdom, and Slovenia to demonstrate that effective mineral indicators should be specific to the resource in question and the public values and objectives.

Jan 1, 2003

By Terence P. McNulty

Gold-bearing outcrops were discovered in 1862 by Union soldiers garrisoned at Needles, CA, near the northwest corner of the future State of Arizona. Sporadic mining began several years later, but engineered shaft sinking and mill construction were not adopted at Oatman and the neighboring camp of Goldroad until about 1900. Geological interpretations in 1915 enabled major production during the next decade. In the late-1930s, USSR&M built a new mine and mill in Gold Road and the District flourished until closure by Federal Order L-208 in October 1942. For about a decade, Oatman’s mines were among the largest gold producers in the American West.

Feb 1, 2024

The only good news in the exploration sector in 1982-a year plagued by low metal prices and weak demand-was precious metals. Gold in particular remained in the forefront, as it has for at least the past three years. The reason for this is partially due to gold's seeming resilience to conventional supply side factors-such as new production-that normally influence many other metals. Also, with projected production costs of about $6.40-$9.65/g ($200¬$300/oz), modest deposits with average grades can offer an early return on capital investment and good profit potential. Keeping escalating capital costs for new mining ventures within reason has shifted gold exploration efforts in recent years. Many mining companies are seeking relatively low grade, modest tonnage, near-surface gold mineralization. This, of course, leads to lower development costs using open-pit mining methods. Recent refinements in the carbon-in-pulp recovery process also has enhanced the economics of such deposits. Slumping economic conditions certainly played a key role in shaping exploration activity last year. Nearly every major mineral-producing state recorded exploration slowdowns. In Alaska, for example, development expenditures approached the level of exploration spending for the first time in the state's history. This not only reflects major companies' decisions to move toward production but also the economic slowdown. The worldwide recession stopped Nevada's exploration and mining boom "dead in its tracks," said John Schilling, state geologist. The year was one of layoffs and closings for the state's mines and exploration offices, he reported. Similar trends were noted in most other states, especially in the West and Southwest. In the Pacific Northwest, however, exploration appeared to continue at a relatively good pace considering the metals market. In the mining geophysical community, recent advances in telecommunications and microprocessor technology are continuing to provide a positive impact. Many geophysicists have begun using satellite digital communication links to access computer systems from remote sites where using a microcomputer would be difficult. There were also major contributions made in exploration geochemistry last year. Highlights include progress in formulating mineral deposit models, geochemical exploration in glaciated and arid environments, and publication of many informative books. The following state-by-state summary and articles on geophysics and geochemistry provides a detailed view of exploration events throughout the US in 1982.

Jan 5, 1983

By J. E. Hoffman, S. P. Sandoval, T. J. Keefe, K. P. V. Lei, O&apos

The U.S. Bureau of Mines investigated the use of the Fe2+/Fe3+-SO2 (FFS) anode reaction in the copper leaching-solvent extraction-electrowinning circuit. The investigation revealed that six process variables, including anode type, Fe 21 concentration, current density, electrolyte temperature, degree of agitation, and manifold injection point were found to influence cell voltage and cell current efficiency. A 47% voltage reduction (0.8 versus 1.5 V) compared to conventional electrowinning with activated lead (ALE) anodes was achieved at a current density of 258 A/m2 (24 A/ft2) with an industrial electrolyte. Current efficiency was maintained above 90%, and S02 above the cell measured less than 1 ppm when activated carbon was used to assist the reduction of Fe" by S02 in the copper electrolyte. Solvent extraction tests showed that Alamine 336 is a stronger H2SO4 extractant than is needed to extract the excess acid produced by the FFS anode reaction.

Jan 1, 1993

By David M. Parkes

Geology is frequently complicated, hence only more regular deposits are mined. Coal is generally thick, often steeply pitching and usually soft or well-cleated. Due to competition from open-pit mines, only two underground mines are operating, McIntyre and B.C. Coal. Several other mines are being planned, the method being evenly divided between hydraulic, longwall, and room and pillar. McIntyre mines in the flat part of their formation (up to 20 degrees) uses continuous miners and shuttle cars in the 3m and 6m seams. This company is considering a retreating longwall face. B.C. Coal operates a hydraulic mine in a 16m thick seam dipping at 10 to 55 degrees with a productivity of about 20 tonnes per manshift.

Jan 1, 1982

By G. Bloomsburg, R. E. Williams, S. D. Vincent

A modeling scheme is developed to simulate the hydrogeologic effects of mine design and development in unsaturated rock. Simulations are conducted using the UNSAT2 finite element computer program and hydrogeologic data from the site of a proposed mined-out waste repository at Yucca Mountain, NV. Results of the simulations are analyzed for: •variations in the direction of ground water flow and in the distribution of pressure head caused by the design of the mined out openings; and •mine design variables that affect the predicted rates of mine water inflow. Evaluating the hydrogeologic impacts of mine design and mine development in unsaturated rock is significant in several respects. Characterization of the preemplacement of wastes along the fastest path ground water flow system at the Yucca Mountain site has been a primary research effort. Ultimately, however, the degree to which waste isolation is achieved will depend largely on the post-mining hydrogeologic environment as altered by the mine design and on the radionuclide inventory and resulting heat effects of the repository. Therefore, an ongoing characterization of the proposed mined-out nuclear waste repository at Yucca Mountain, NV, is recommended. Modeling results indicate that: •mined out openings will affect the movement of ground water, both in rate and direction; •hydraulic effects of mine development depend on the hydrogeologic environment and on mine design geometry; •mine water inflow is possible in the unsaturated zone, even for mines developed in hydrogeologically homogeneous rocks; and •mine water inflow can occur at values of down ward flux that are appreciably less than the saturated hydraulic conductivity of the overlying rocks.

Jan 1, 1991

By Wolfgang Pietsch

Roller presses were first invented in the middle of the 19th century, for the economical size enlargement of coal fines as fuels. Coal briquettes became quickly accepted for industrial and domestic use giving rise to a large and sucessful industry, particularly in Europe, Japan, and North America. When, towards the middle of the 20th century, coal was more and more replaced by other energy sources, such as electricity, gas, and oil, roller press manufacturers searched for alternate applications of this equipment. In addition to contemporary coal briquetting, in fields such as smokeless fuel and form-coke, it was found that redesigned and modernized roller presses, which are now capable of exerting high forces, are versatile machines for many tasks in mineral processing. Today they are used for: - the "classic" pressure agglomeration and - the "new" high pressure comminution. In pressure agglomeration, the characteristics of fine minerals are improved by forming briquettes or granulated products from compacts. During size enlargement with roller presses briquettes are directly obtained while granular materials are produced by crushing and sizing of compacted sheets. The processes are carried-out essentially dry and often do not require binders other than those inherently contained in the feed and "activated" by the high forces and/or elevated feed temperatures (e.g. hot briquetting). Therefore, no foreign materials (impurities) are added. Another advantage of the technology is, that wide particle size distributions are acceptable or desirable as feed materials, including millimeter or even centimeter sized particles. Plastic particles deform and brittle materials are crushed during pressure agglomeration. A relatively new application of roller presses in mineral processing is the utilization of the crushing effect when brittle materials pass the nip area between the rollers. It was found that this crushing mechanism is very efficient thus saving energy, particularly in grinding circuits handling large capacities. The paper introduces the fundamentals of the process and describes the design as well as applications of modern roller presses in mineral processing.

Jan 1, 1995

By Richard E. Gertsch

The recent upswing in mining coincided with increased environmental concern. These trends have significantly increased regulation, but have not always provided sound environmental protection. Throughout, mining has remained passive, reacting to initiatives from outside. The high road to environmental protection must be an active strategy. The mining industry must take the lead and develop an environmental program effective in price and protection. It must involve all levels of mining. The mining industry should be the real environmental activist. We have the most to gain by sound environmental protection and the most to lose if the environment decays.

Jan 1, 1991

By Robert C. Freas, Donald D. Carr, Lawrence F. Rooney

Perhaps no other mineral commodities in this volume have as many uses as limestone and dolomite. These carbonate rocks are the basic building blocks of the construction industry, the material from which aggregate, cement, lime, and building stone are made. Carbonate rocks, and their derived products, are used as aggregates, fluxes, glass raw material, refractories, fillers, reactive agents in sulfur-oxide removal, abrasives, soil conditioners, ingredients in a host of chemical processes, and much more. Although the use of limestone and dolomite goes back before recorded history, new uses and products are continually being found. Carbonate rocks form about 15% of the earth's sedimentary crust and are widely available for exploitation. Found extensively on all continents, they are quarried and mined from formations that range in age from Precambrian to Holocene. Reserves of carbonate rock are large and will last indefinitely, although high-purity deposits may be absent or have limited availability in certain areas. Limestone and dolomite are so useful and so abundant that in 1989 about 798 Mt were produced in the United States. In fact, about 75% of all stone quarried or mined in the United States was carbonate rock. Sand and gravel was the only mineral commodity produced in greater quantity. In this chapter we have sought to provide the general reader an overview of carbonate rocks, their composition, distribution, production, and uses. The literature on the limestone and dolomite resources of the United States and Canada is so vast and diverse that one can easily become mired in print. We tried to list those references that are easily accessible and that provide the economic geologist with a starting point for more intensive study. The table listing selected references on limestone and dolomite resources in Canada and the United States reflects our attempt to be selective rather than exhaustive and to direct the reader to the best sources of detailed information.

Jan 1, 1994

The capability for on-line measurement of the quality characteristics of conveyed coal now enables mine operators to take advantage of the inherent heterogeneity of those streams and split them into wash and no-wash stocks. Relative to processing the entire stream, this reduces the amount of coal that must be washed at the mine and thereby reduces processing costs, recovery losses, and refuse generation levels. In this paper, new approaches for optimal control of the segregation process, using time series models and empirical distributions, are presented and demonstrated using field data.

Jan 1, 1998

By Patrick J. Ryan, Johann F. Kerl, Angelos N. Findikakis

Introduction Tailings disposal methods used by the mining industry include the use of on-land impoundments, surface and underground mine backfill and marine disposal. The latter method, where applicable and under certain circumstances, can be the most economical and best environmental option. The term marine disposal is used to describe deposition of tailings in the open ocean, coastal waters, fjords and inland lakes. A major element in planning and designing a marine outfall is the assessment of its potential environmental impacts. The nature of the disposed tailings, and the physical, chemical, and biological characteristics of the receiving water body must be carefully assessed prior to deciding whether marine disposal is an acceptable option for a particular project. During the last decade, the North American mining industry has demonstrated a commitment to studying potential adverse environmental impacts of marine tailings disposal and to continue monitoring of the receiving waters. Extensive monitoring programs have been undertaken by Canadian mines. Marine tailings disposal is not used in the United States today. One of the largest U.S. mines proposing to use this option is the Quartz Hill mine of U.S. Borax in Southeastern Alaska. To assure the regulatory agencies and the public of the viability and acceptability of this option, U.S. Borax undertook an extensive program of environmental studies aimed at assessing the impact of marine tailings disposal. This program was part of the feasibility and environmental permitting studies conducted by Bechtel Civil & Minerals, Inc, on behalf of U.S. Borax. Due to the unique nature of the proposed tailings disposal system, a Board of Consultants was established. The Board assisted in planning the modeling and field program and reviewed ongoing work. This paper outlines the basic elements of the marine tailings disposal study program which can be viewed as a prototype for similar studies elsewhere. Background The Quartz Hill molybdenum deposit is located on a knoll in an elevated valley in a mountainous region of southeast Alaska, about 45 miles east of Ketchikan (Figure 1).

Jan 1, 1986

By H. Lyn Bourne

This is the sixth annual tabulation that gives mineral royalty information. This tabulation, like the previous editions, includes all of the earlier data plus more than 100 new entries. In addition to the royalty information, some entries show the cost of purchased reserves. An article in the December 1984 Kentucky Coal Journal could have far reaching applications. It explains that a banking firm examined the "reserve risk" as one of six factors for analysis when financing a coal project. The firm concluded that coal reserves in Kentucky are worth an average of $0.29/t ($0.26 per st) in-place. The banking firm based this in-place value on its examination of more than 50 leases. In-place value is especially important when trying to establish a mineral value for a given deposit. Ernie Lehman wrote to this author after last year's column appeared and he quoted the lease rates for lead and zinc on federal land. He states, from first hand information, that the leases are based on a percentage of net smelter return as follows: 4% for the first five years, 4.5% for the next five years, and 5% thereafter. The figures used in last year's column ($ per st) came from dividing reported royalty income by reported production. The information reported last year merely translates the results of the net smelter return (as written in the lease) to royalty income per ton to the US Government for the various years. Statistics from the Minerals Management Service of the Federal Government show that oil and gas account for 40% and 53%, respectively, of the Federal royalty income. Coal accounts for about 4% and all other minerals, the remaining 3%. Oil and gas leases are mostly at 12.5%. Most of the coal leases are at 12.5% for surface mining operations and 8% for underground mining. Many of the other commodities are leased at 5%, which has been true for decades. Relative to Federal leases, this year's table shows some percentages and some costs per ton. This was done to give information about the leases and also to show income produced by various commodities. Note that some commodities have a variation in $/ton even though the royalty percent is the same. These variations result from a combination of factors that influence the value of a mineral commodity. The same caveats that have appeared in previous columns relative to factors that influence the value of reserves are restated. The data in the table serve as a general reference and are not intended to present an absolute scale of reserves costs. Several factors influence the value of any mineral commodity. The factors include: • location/transportation (especially significant for most industrial minerals); • market conditions both for the commodity and the company acquiring the right to mine it; *quality or grade of the deposit as it reflects the amount of processing/beneficiation necessary to produce the finished product; and • legislative restrictions and conditions for mining a given material at a given site. These and other factors will significantly influence the cost of reserves. The table shows the range of royalties and the variations in the basis of computing the fees. In a few instances, it gives the cost of acquired reserves based on purchase price and quantitative estimates of the material in place. The table lists the commodity in column 1, and the subsequent columns give the location - either by state, US geographic area or Canadian province; the cost - R for royalty and P for purchased cost; and the year in which the lease or purchase agreement occurred. The last column offers either comments or gives a footnote number for more information. The cost column requires more explanation. The units may refer to cubic yards (/yd), cubic feet (/cu ft), tons (/T, 2000 lbs) or acres (/A). 1 cu yd = 0.7646 m3 1 cu ft = 0.2832 m3 1st=0.9078t 1 acre = 0.4047 hm or m2 In several cases, the royalty is a percentage of the sales price of the finished product and is levied against either the amount produced or the amount sold. We thank those who contributed information for the table: G. Anderson, B. Brown, R. Ganis, K. Hauser, E. Lehman, and S. Sims. Their help is appreciated as are the contributions by those who asked to remain anonymous. This column requires additional information each year. That data must come from people in the minerals industry who have royalty information. What appears in the table is only a very small fraction of the cost information relative to the various commodities and the geographic areas for which there is royalty information. If you find this column of interest and possess information write the author at the address given in the author's box or call 313-462-0005.

Jan 7, 1988

By William T. Folwell

INTRODUCTION - CURRENT RAISE BORING PRACTICES Raise boring is a comparatively new tool to the underground mining and construction industries. Underground raise boring, in this country, had its beginning in the early 1960's, in the iron mines of Michigan. These first raises were bored 40 in. and 48 in. in diameter with maximum lengths of approximately 200 ft. Since the late "sixties", the raise boring machine has been accepted by the mining industry as an important machine to increase excavation rates, provide adequate ventilation airways, improve safety, and reduce costs, to name a few of the benefits. The construction industry is now accepting raise boring techniques for hydro-electric power projects, water supply projects, tunnel projects, waste water projects, etc. Raise drills are now capable of boring raises to diameters as much as 12 ft, in the softer rock types. Raise lengths range from 200 ft to as long as 1700 ft. Bored raises, in general, are bored at dip angles ranging from 45º to 90º, depending on the requirement of the raise. The general practice is to drill the pilot hole down to an opening below and up ream the pilot hole to the required diameter. The pilot hole (9-7/8", 9", 11", or 12-1/4" diameter) is generally drilled with compressed air to remove the cuttings. In the event that ground water is encountered and removal of cuttings is impeded, a foaming agent is added to assist in lifting the cuttings. When excessive water is encountered, water is used as the circulation medium and the cuttings are removed by pumping. During the reaming cycle, the cuttings fall by gravity and are removed from the bottom of the raise by conventional methods.

Jan 1, 1997

By G. Ansong, P. K. Achireko

The authors present a new mineral price model, compare it with time series and naive models, and analyze the effects of the forecasting models on mineral project evaluation. Mineral commodity prices are volatile, which means that the results of evaluation tools that do not treat the stochasticity of metal prices rigorously may be misleading. But, in mine valuation, commodity price forecasts are required to assess the economic viability of a project. In this study, a new mineral forecasting method, called the MNDRVG-MFNN-RM model, which incorporates randomness, neural networks and regression models, is introduced. The MNDRVG-MFNN-RM model, a naive method and time series model were used to forecast gold prices for two successive years for the evaluation of a proposed open-pit mine. The MNDRVG-MFNN-RM model yielded the best results among the three methods. It produced the true optimum pit limits and an optimum pit value slightly less than the true optimum value. The main novelty of the methodology is the simulation and rigorous analysis of the randomness property associated with mineral prices to reduce the estimation and forecast errors, an important contribution to mineral venture evaluation, mine planning and design.

Jan 1, 2000

By D. Dunbar

Flooding of open pits now receives considerable attention from the mining industry as an option that may minimize environmental impacts, particularly when anoxia in pit lake deep waters can effectively eliminate oxidation of pit-wall sulphides. A state-of-the-art, coupled physical-geochemical pit lake model is used to verify that a cost-effective, environmentally responsible closure strategy for the open pit at the Kori Kollo gold mine, southeast of La Paz, Bolivia is to adopt a controlled, two-stage infilling of the open pit upon cessation of operations. By filling the pit initially with highly saline waters from evaporation/infiltration basins and naturally saline deep groundwater, followed by capping with fresh river water, a very stable and strongly stratified pit lake will be developed. In addition, the stratification will result in the isolation of metal-rich saline bottom waters from surface waters of good quality. Results of this model provide defensible predictions of the physical stability and evolution of water quality in the Kori Kollo pit lake over time. The model results indicate that anoxic conditions will develop below the fresh-saline water boundary within 1 to 2 years, followed by the rapid onset of sulphate reducing conditions in the bottom waters. Hydrogen sulphide produced by sulphate reduction will readily react with dissolved metals to form highly insoluble metal sulphides. The process results in the gradual removal of metals from the water column and the concomitant improvement of water quality over time. A notable benefit of this strategy is that it can be fully integrated with other mine site closure options as well as future environmental management strategies. The proposed plan allows for: 1) safe storage of saline evaporation basin waters; 2) the potential for passive treatment in anoxic bottom waters of ARD seepages from other mine site operations should they arise; and 3) a repository for future reactive wastes that could be effectively isolated in a physically and chemically stable environment.

Jan 1, 2001

By K. T. Valsaraj, L. J. Thibodeaux

Solvent sublation, the separation process for the removal of two hydrophobic compounds (penta- and trichlorophenols) from the aqueous phase, is discussed, as is a steady-state mathematical model for fire process. Solvent Sublation "'as conducted in a continuous countercurrent mode. The underlying mechanisms, theory and experimental details on the effects of process variables on removal efficiency are reported.

Jan 1, 1994

By James M. Link

The first rule of mineral deposits always seems to be: the deposit is never close to the market. With gems and precious metals, this is not much of a problem. But with most of the mineral commodities used in today's world, transportation becomes a major part of the cost to the consumer. In Japan, for example, more than 60% of the cost of coal to the consumer may be attributed to transportation. The purpose of this article is to examine pipeline transportation, particularly mineral slurry pipelines, as a means of getting the mineral to market. Pipelines Today Regulated pipelines in the US totaled nearly 724 Mm (450,000 miles) in 1980 according to the Federal Energy Regulatory Commission (FERC). Worldwide, more than 210 Mm (125,000 miles) of new pipelines will start construction in 1982 at an estimated cost of more than $150 billion. According to the Bechtel Corp., the period between 1982 and 2000 will see major growth in pipelines of all kinds. In North America, major movements of crude oil from Alaska and synfuels from the Rocky Mountains will require the construction of nearly 16 Mm (10,000 miles) of new pipelines. Nearly 42 Mm (26,000 miles) of new gas transmission pipelines will be needed to tap both US and Canadian arctic gas fields and move the gas to major markets on both coasts. Other pipelines will be required to move additional quantities of natural gas from the Rocky Mountains to more populous regions. Bechtel says more than 24 Mm (15,000 miles) of slurry pipelines will be needed to transport coal from both eastern and western coal provinces to the Mississippi valley and coastal areas. In 1980, 125 companies delivered more than 1 km3 (6.5 billion bbl) of crude oil and 652 hm3 (4.1 billion bl) of products in the US. At the same time natural gas pipelines transported 498 km3 (17.6 trillion cu ft). The reported investment by these companies was nearly $20 billion at the end of 1980. Advantages of Pipeline Transportation The obvious success and vitality of the oil and gas pipeline industry is based, at least in part, on the fact that pipelines are a very efficient and low-cost method of transportation. This fact, coupled with the need for lower cost trans¬portation, has led to the marriage of oil and gas transmission technology and the bulk mineral solids transportation industry. The off-spring of this marriage is the mineral slurry pipeline. Slurry pipelines have a number of advantages over other transportation methods. One of these is the fact that they are buried-out-of-sight, out-of-mind. Second, they are relatively small users of labor because they lend themselves to automation and remote, or even computer control. Third, they offer an attractive economic alternative to other transportation systems. For example, for a 1000 km (621 miles) distance, rail costs of 1?/ km (1.7?/ton-mile) are about equivalent to slurry pipeline costs. But, as the distance increases, pipeline cost per t-km continues to drop while equivalent rail charges remain essentially insensitive to distance. Where existing rail, barge, or ocean ships are available, the cost of new construction associated with a slurry pipeline probably will render it noncompetitive. However, where new rail or other construction is needed, the cost of a slurry pipeline is very competitive. About three-fourths of the cost of a pipeline is in pipe, fittings, and construction. Nearly a fifth of the investment is in pump stations and the remainder is in right-of-way, surface facilities, utility acquisition, communication facilities, and other support areas. The fact that pipelines are capital intensive is, at the present time, a mixed blessing. For example, the delivered cost of coal in a hypothetical project doubles when the cost of money rises from 9% to 17.5% per year. The largest cost element for delivered coal in this example is in depreciation and finance charges. The next largest cost element is electricity to power the pumps, with labor making up the smallest increment of the delivered cost of coal. World Slurry Pipelines The idea of a slurry pipeline was probably first investigated in the latter 19th century, but the first ones were successfully built and operated in the US in the early 1900s. Today, they are fairly common worldwide. Table 1 shows a number of the world's slurry pipelines. An examination of these will further emphasize the fact that pipelines provide a cost competitive alternative where new construction of a transportation system is required. In each of the examples, the desired mineral commodity is located in a remote corner of the world, markets are at a great distance, value of the commodity is not great, and no other transport system is available.

Jan 10, 1982

By J. M. Dean, R. L. Grayson, R. C. Althouse, M. J. Klishis, G. L. Winn

Using powerful database management software, nested-field analysis and microanalysis of narratives have been made of West Virginia accident data, resulting in a new approach for targeting and prioritizing safety interventions by county, mine size, specific mine, job title, type injury, etc. and combinations of these parameters. The analyses have been useful in focusing training and discussion sessions on specific work problems, trends, conditions, and situations for targeted groups of miners. Application of the technique will be presented in this paper, along with comparisons of various mine performance measures.

Feb 24, 1997

By James J. Scott

Introduction Friction Rock Stabilizers, trade name Split Sets, are presently under research and development by Ingersoll-Rand Company and Dr. James J. Scott, inventor. Conceived in 1953, the system is a patented process undergoing extensive field and laboratory testing. The author has published papers on the Split Set System earlier (References 4, 5, 6) The Split Set System holds promise to be a revolutionary development in the field of ground control. The system produces an interior reinforcement to a rock mass which: 1. Is simple in its concept. 2. Adjusts to the degree of restraint needed to match rock properties. 3. Provides a yieldable support and, later, a more rigid support as it is needed. 4. Pre-loads the rock in compression to increase stability. 5. Is a full-contact, fully tensioned device to resist rock loads. 6. Minimizes the stress concentration effects inherent in many interior support devices. 7. Improves safety for the miner. 8. Is cheaper than a grouted system. 9. Offers the rock mechanics engineer an opportunity to design in a fashion not before possible.

Jan 1, 1977