Search Documents

By P. C. Kapur

The kinetics of green pelletization in a laboratory balling drum have been studied, using pulverized limestone as a model system. The growth characteristics of green pellets were found to be extremely sensitive to the moisture content of the material. Empirical kinetic equations, which incorporate a function of specific surface of the pellets as the criterion for growth potential, have been found to describe growth in a nucleation region and in a ball growth region. The rate constants in the kinetic equations are strongly dependent on the moisture content of the material being pelletized. Size distributions of the halls at different stages of pelletizing are also discussed.

Jan 1, 1965

By P. E. Richardson, N. P. Finkelstein, Z. Chen

The large band gap and insulating properties of sphalerite have limited the application of standard electrochemical techniques for studying its reactions with flotation reagents. This problem has been overcome by developing electrodes that rely on the surface conductance produced when sphalerite is activated with copper or other heavy metals. A brief exposure of the mineral in copper sulfate solutions results in electrodes that exhibit significant electrochemical activity characteristic of copper sulfides. Voltammetry studies conducted on sphalerite activated in 10-4 M CuS04, solutions at pH 4.6 provide information on both the amount and the nature of the activation product(s). It is shown that copper activation is strongly dependent on the electrochemical potential applied during activation. Activation at potentials increasingly negative of the rest potential causes a progressive increase in the amount of copper on the surface; activation at potentials positive of the rest potential decreases the amount of copper on the surface. The results indicate that both the kinetics of copper uptake and, possibly, the chemical composition (stoichiometry) of the activation product are controlled by the electrochemical potential.

Jan 1, 1995

To simplify programming, image analyzers commonly measure either linear intercepts or the areas of particles and grains to determine liberation based on polished section mounts. However, the concentration of minerals by flotation is based on reagents that interact with the exposed surfaces of the minerals. Thus, it is often perceived that image analyzers should measure the perimeter of the mineral of interest in the ore particles. A comparative liberation study of thirteen samples collected from a flotation plant processing a complex base metal sulfide ore showed that the liberation of the ore minerals determined by area measurements is very similar to the liberation determined by the exposed perimeters. The liberation determined by exposed perimeters is more appropriate only for those cases where the mineral texture is so complex that it is retained in the small particles generated in conventional grinding operations.

Jan 1, 2002

By C. R. Copeland

Water sprays are a common method used to reduce particulate matter (PM) emissions. Various factors such as wettability, surface area coverage, fine particle engulfment rates, interparticle adhesion forces, suppressant penetration and suppressant longevity have all been suggested as critical factors in achieving effective PM control. However, it has not been established which of these factors are the most important. Experimental work indicated that suppressant penetration is the most critical of these factors. The length of time after application that suppressants were effective was also improved by using hygroscopic reagents that retained moisture to prevent evaporation. Maximizing suppressant penetration and improving suppressant longevity led to an average 86% reduction in PM10 concentrations in laboratory dust tower tests.

Jan 1, 2008

By George J. Hartman

The Fort Cady in situ borate-mining project involves recovering boron from a deposit more than 400 m (1,300 ft) below the surface. The resource recovery method is a new in situ mining technology that uses weak acid solution injected directly into the ore body. As the acid contacts the calcium-based ore (primarily natural colemanite), the contained borate values are digested as boric acid. This boric acid solution is then pumped to the surface by submersible pumps. A series of chemical reactions and precipitations are performed that result in the production of calcium borate. The borate values are then recovered as a finely divided solid white powder. The refined product is sold under the trade name Cadycal 100. The Fort Cady in situ borate-mining project is located about halfway between Los Angeles, CA and Las Vegas, NV in the Mohave Desert.

Jan 1, 1996

By Paul H. Lu

This paper proposes a novel method, "integrity factor approach," of mine-pillar stability evaluation based on in situ triaxial-loading measurement. The pillar integrity factor is defined as the quotient resulting from division of integrated total pillar strength across the critical dimension by the integrated total pillar load across the same dimension. The integrity factor is dynamic, while the conventional safety factor is static. With this approach, the pillar stability can be evaluated at any stage of mining progress during panel operation. It automatically considers the progressive failure of the pillar and post-failure strength without the need to clearly define the boundary between yielded and intact zones of the pillar. Based on two case studies, the integrity factor approach is shown to be a practical, effective technique for evaluating stability of conventionally designed pillars. It is suggested that a more realistic estimate of in situ pillar strength could be made based on the combination of in situ triaxial-loading measurements and laboratory true triaxial compression tests, rather than through the traditional combination of biaxial-loading measurements and conventional triaxial compression tests.

Jan 1, 1986

By T. J. Nelson

Natural aggregates, primarily stone, sand and gravel, are recovered from widespread, naturally occurring mineral deposits and processed for use primarily in the construction industry. They are mined, crushed, sorted by size, and sold loose or in concrete products to build roads, houses, buildings and other structures. Smaller quantities are used in agriculture, cement manufacture, and chemical and metallurgical processes. The growth of cities, their buildings and the highways that connect them have created demand for enormous quantities of aggregates. Consumption has now reached 9 t (10 st) per person and continues to grow faster than population. The aggregates industry is the largest mining industry in the United States in terms of production by weight, by volume and by number of active operations. About 80 percent of the concrete pavement and more than 90 percent of the asphalt pavement is composed of aggregates.

Jan 1, 2006

By Gennaro Gerald Marino

In this paper the main subsidence- ground-structure interactions and an overview of the response of surface structures to subsidence ground movements are presented. The purpose of the paper is to augment our understanding for more effective application of available data as well as to highlight the essential site conditions in building response. The data presented general1 y applies to houses to structures up to 2-3 stories high and no more than several hundred feet in length. Superstructures of these buildings are supported by exterior (wood-frame or masonry) bearing walls with the interior floor loads carried by essentially one row of interior columns. This paper is not directed towards the response of tall buildings, steel-framed structures, or building types commonly associated with schools, churches, libraries, etc.

Jan 1, 1986

By John S. Jones, Ralph E. Brown

INTRODUCTION For more than a century, artificial ground freezing has been used for groundwater control and structural support for excavations. Most of the early uses of the freezing method were for sinking deep access shafts for mines and tunnels (1,2,3,4). More recently, ground freezing has increasingly been used for construction of large diameter cofferdams and soft-ground and mixed-face tunnels (5). Although ground freezing has been used in the past-for tunnels, it was invariably used as a last resort measure, where more conventional measures could not be used. The more recent freezing applications, however, have become increasingly cost competitive with more conventional techniques, and are now being included as part of the design concept (6,7,8,9,10,11,12). The purpose of this paper is to describe some of the more recent applications of ground freezing for tunnel construction. The paper begins with a brief description of the most commonly used freezing system, the Poetsch process. Recent tunneling projects utilizing ground freezing for structural support are then discussed. DESCRIPTION OF THE FREEZING METHOD The most commonly used freezing method is the Poetsch process, which was originally developed by F. H. Poetsch in the late 1800's. The system consists of a brine coolant, typically calcium chloride and water. Freezepipes are placed into boreholes or are

Jan 1, 1979

By G. B. Amicucci

Golden Sunlight Mines Inc. operates an open-pit gold mine and cyanidation plant about 11km (7 miles) northeast of Whitehall, MT. Golden Sunlight is a subsidiary of Placer Dome US Inc. Mining is accomplished with conventional open pit drilling, blasting and hauling methods. The mining rate is about 102 kt/d (113,000 stpd). Gold occurs as fine-grained disseminations in a pipe-shaped breccia and in immediately adjacent country rock. The ore body is low grade, averaging 2 g/t (0.059 oz per st) of gold. The metallurgical plant uses conventional carbon-in-pulp (CIP) technology. Daily throughput averages 6.5 kt (7000 st). Recoveries are enhanced through a sand tailing retreatment facility while a preaeration process reduces operating costs. The low grade ore dictates that maximum mill throughput at the desired grind size be maintained. Therefore, in October 1988, an Armco Autometrics (now Denver Autometrics) particle size monitor (PSM) 400 was commissioned. The PSM 400 is an on-line instrument. It measures particle size and percent solids in a slurry stream. The PSM pulls its own sample, deareates the sample and passes it through diametrically opposed ultrasonic sensors. The unit uses ultrasonic sound to measure the deareated slurry stream's particle size and percent solids.

Jan 1, 1991

By Heinz Distelmeier

The New Austrian Tunneling Method was, as is well known, developed from conventional rock tunnelling. In Germany about 10 years ago the NATM began to be applied to partially stable soils by incorporated excavation and support methods to allow its use with these soils. The advantages of this tunnelling technique - adaptability, ecomomy, and quality have resulted in its widespread usage. Today, about 85 % of all mined tunnels in Germany are produced with this technology. This rapid development has resulted in about 40 companies operating within a geographical area about the same size as the state of Illinois that are capable of utilizing the NATM. In most cases German contract/award procedures allow the contractor to develop alternate design and plans. As a result of this flexibility and intense competition, safety factors have been gradually reduced to the lower limit of what could be regarded as demonstrably safe, and the utilization of the NATM has expanded to include higher risk conditions, namely * excavating larger cross sections. * working with less overburden. * work undertaken under less stable soil conditions.

Jan 1, 1983

By V. A. Leach, Lokan. K. H., S. B. Solomon, R. S. O’Brien, L. J. Martin, K. N. Wise

INTRODUCTION The development during 1979 of a relatively small, but high grade (10,000 tonnes uranium at an average grade of 2 per cent), uranium ore body at Nabarlek in the Northern Territory, Australia offered an excellent opportunity to obtain detailed radiation data for an open cut mine operating during the dry season. The ore body (Queensland Mines Limited-1979), which was completely extracted in a period of four and a half months, consisted of a vein type deposit dipping at 30 to 45 degrees and contained a central core of pitchblende in massive and irregular pods, surrounded by lower grade fine grained disseminated pitchblende. Mineralisation extended from the surface to a depth of 72 metres over a length of 230 metres with an average but variable thickness of 1D metres. Ore near the surface had been heavily weathered and complex secondary minerals were formed which had dispersed from the main vein. Mining was carried out with large earth moving equipment. Overburden and weathered surface ore were removed initially with scrapers. At greater depths bulldozers were used to rip and assemble ore and rock at each level, and these were removed by large trucks to the ore and waste rock stockpiles. Where necessary, blasting took place during shift changes each evening. Mining was essentially continuous with two ten hour alternating shifts working for thirteen days out of fourteen. At the completion of mining a relatively small excavation (335m x 185m x 70m) remained, and this will serve as a tailings repository during the milling phase. FIELD MEASUREMENTS The inhalation of radon daughters, arising from the radioactive decay of radon gas is well established (Archer et. al. 1973) as a potential hazard in the uranium mining industry. Control over radon and its daughters to ensure that recommended exposure limits are not exceeded is achieved by providing adequate ventilation, and under normal circumstances natural ventilation from an open pit should be sufficient. However, during the dry season it is not uncommon for stable atmospheric conditions, with little horizontal air movement, to develop - particularly at night - and significant radon daughter concentrations may accumulate. Throughout the entire mining period measurements were therefore made of radon and radon daughter levels at representative locations within the pit and on the ore stockpile as it developed. Initially these measurements were carried out manually, using the Rolle method for radon daughters, (Rolle 1972) and .scintillation cells (Lucas 1964) or a two filter tube for the determination of radon (Thomas 1970). For the latter half of the period however, a continuous recording instrument, developed within the Laboratory was used to provide a detailed record of radon daughter levels within the pit. At the same time, continuous readings of wind speed and direction, and vertical temperature gradient between 10 and 3D metres were recorded on a 30 metre meteorological tower, situated 800 metres from the pit. Radon Emanation Rates It is evident that radon and radon daughter concentrations depend on the grade, or more particularly, on the surface radon emanation rate of the ore which is exposed. Accordingly, as the mine progressed, detailed measurements were made of both of these quantities. The surface emanation rate of radon was determined for each ore bench as it was exposed by placing an extended array of canisters, filled with freshly degassed activated charcoal, face down on the ore for a known time. These canisters, which had previously been calibrated in the Laboratory, adsorb radon with high efficiency, and the total radon adsorbed is measured after retrieval by detecting the gamma rays from the trapped radon daughters (Countess 1977). At the same time, as each canister was placed in position, a measurement of the local ore grade was made for each location. This was achieved with a calibrated sodium iodide scintillation detector, adjusted to detect the 609 keV gamma ray from the isotope 2148i, a decay product of radium. Finally, measurements were made of the radiation field 1 metre above the surface, with a gamma ray survey meter, which was calibrated in the Laboratory. The relationship between the scintillator count rate and ore grade was determined by comparing the scintillator output with the gamma monitor, and relating the latter measurements to ore grade (Thomson and Wilson 1980). It was observed that while emanation rates and ore grades varied widely, the ratio of emanation rate to ore grade was in general fairly stable. A plot of this ratio is presented as a function of depth below the original surface in Figure 1. For most observations the ratio is constant at a value of 80 Bq m-2 s -1 per unit ore grade, where ore grade is expressed as percentage of U308. At the surface however, where the ore was weathered, the ratio was about a factor of three higher, and at two particular depths, where high grade pitchblende was being removed, it was very much lower. This was not unexpected as earlier Laboratory studies of drill core samples from Nabarlek had indicated that the emanation coefficient (the fraction of radon produced within the ore which escapes from the mineral particles) decreases with increasing ore grade.

Jan 1, 1981

By M. H. Pelkki, R. J. Sweigard, P. W. Conrad, J. M. Ringe, D. H. Graves

Research has shown that excessive soil compaction is detrimental to the establishment of trees in reclaimed soils. Dry bulk density and penetration resistance are two soil parameters that can be used to indicate the level of compaction in reclaimed soils. It is believed that reclamation practices which minimize soil compaction will produce better results when forestland is the intended post-mining use. The University of Kentucky has developed reforestation test cells on reclaimed soils at a surface mine in eastern Kentucky to test this hypothesis. Each test cell has been planted with various species of trees, and since 1997, data have been collected at these test cells for soil average dry bulk density, average penetration resistance, average depth to refusal, and average survival rate of trees. These data have been correlated to determine the relationship between soil compaction and tree survival rate. It is believed that the two soil compaction parameters may ultimately be used to predict tree survival rates on reclaimed surface mined lands.

Jan 1, 2001

By E. William Rossi, Audrey F. Glowacki, Richard L. Unger

The U.S. Bureau of Mines has developed a graphics-based computer model to assess operator visibility for continuous miners, shuttle cars, and scoops. Using digitized drawings of the machine, the program can analyze visibility for both 5th percentile female and 95th percentile male operators. This model was used to predict 95th percentile male operator visibility for two shuttle car designs. These results were then compared to those obtained from a manual assessment of visibility using the actual shuttle cars. The methods showed good correlation except for several cases which were attributed to imprecise digitization of the machines.

Jan 1, 1992

By G. T. Adel, J. D. Miller, C. L. Lin

In view of the success of recent laboratory studies using X-ray computed tomography (CT) to determine coal washability and with the availability of high-speed CT systems, it now seems possible to design an on-stream washability system for the control of coarse coal-cleaning circuits. Design features for such a system are examined and possible control strategies are discussed for different applications.

Jan 1, 1995

By P. Mousset-Jones, F. Calizaya

This paper explains and discusses a computer program that has been developed to determine the ventilation design parameters for complex auxiliary ventilation systems such as those found in the construction of long excavations with multiple headings. The program is based on the principle of partitioning the system into segments of finite length, and formulating and solving the resulting networks recursively. The resulting network problems are solved analytically. With this program, the size of fans can be determined in order to reduce the total leakage and minimize the flow recirculation. The application of the program is illustrated by the detailed solution of an auxiliary ventilation system proposed for the Exploratory Studies Facility (ESF) at the Yucca Mountain Project, Nevada.

Jan 1, 1995

By D. S. Bird

Kennecott Utah Copper began a modernization program in 1986 that was aimed at expanding and updating mining and ore process facilities at the company’s Bingham Canyon copper mine and concentrator near Salt Lake City, UT. Major components of the project included installation of an in-pit crusher, a transfer conveying system and a new ore concentrator with a design capacity of 70 kt/d (77,000 stpd). The Copperton concentrator was commissioned in February 1988. The grinding circuit is one of its principal features. It consists of three identical lines, each with a 10.4-m- (34-ft-) diam x 4.6-m- (15-ft-) long semiautogenous grinding (SAG) mill and two 5.5-m- (18-ft-) diam x 8.6- (28-ft-) long ball mills. The SAG mills are driven by two 4.5-MW (each) (6000-hp) variable- speed dc motors through a clutch-pinion gear-ring gear assembly. The ball mills are driven by 4.1-MW (5500-hp) synchronous motors coupled through a typical clutch-pinion gear-ring gear system.

Jan 1, 1995

By Barry R. Doyle, Ilsley Roger C., John Ramage

It was anticipated that settlement would occur when tunnels were excavated in weak organic soils with high groundwater levels in downtown Milwaukee. Because of the potential for damage to adjacent buildings, an approach was devised during the design to address this issue. In order to do so effectively, estimates of settlement trough geometry were made; buildings identified which were potentially at risk; the means of settlement measurement designed; and threshold limits of settlement and courses of action specified. Bid items were provided for underpinning the critical structures. The approach addresses the design issues and delineates the sharing of risk between the owner and contractor. The predicted and actual performance experienced are also discussed.

Jan 1, 1989

By A. M. Marabini, V. Alesse, Belardi. G.

An alternative flowsheet was designed for the flotation treatment of a complex sulfide ore from the Sotiel Mine in Spain. The ore contains 0.71% Cu, 2.24% Pb and 5.63% Zn. Two specially developed synthetic collectors, methyl-mercapto-benzoxazole (MMBO) and 6n-propoxy-mercapto-benzo-thiazole (PMBT), were examined. MMBO exerts a specific action on copper and zinc minerals after treatment with copper sulfate, and PMBT exerts a specific action on Pb minerals. Flotation operating variables (pH, frother type, frother quantity and feed particle size) were examined by means of rougher flotation tests to determine the optimum conditions for the new collectors. Once the optimum conditions were determined, a series of open flotation circuits were run on feeds of various particle sizes (obtained by different types of grinding). The objective was to obtain high-grade Cu and Zn concentrates. The results of the open-circuit tests demonstrated that a Cu concentrate grading from 18% to 23% Cu and a Zn concentrate grading from 40% to 48% Zn can be produced.

Jan 1, 1996

By D. S. Cavers

INTRODUCTION This paper discusses aspects of rock engineering applicable to surface gold mines. Discussion particularly centers on areas in which rock mechanics can enhance the mine productivity or profit- ability. Methods of analysis are discussed briefly but for more detai1s the reader is referred to the appropriate references. A team approach to the overall design of the pit generally pro- duces a better result at an overall lower cost. In particular, money is wasted by asking for a "report on slopes" and then input- ting this slope angle into a pit design and economic analysis study without further reference to the geotechnical engineer. Pit slope angle depends on slope orientation, location, pit shape, pre-existing discontinuities and mining methods. Preliminary slope angles can be produced but optimization depends on ongoing inter- action between the mining engineers, geologists and geotechnical engineers. This interaction can a1 so substantially reduce overall design time which may be critical in bringing remote plays into production. Most surface gold mines in North America are in igneous or metamorphic environments. Rock mechanics aspects discussed in this paper will be discussed with reference to these environments al- though most of the principles and comments are applicable to sedimentary environments as we1 1.

Jan 1, 1987