Search Documents

By Wilhelm Knickmeyer, Johannes Henneke

PREFACE For about 1 year Bergbau-Forschung GmbH, central research institute of the German Coal Mining Industry, undertakes full size tests for waterjet assisted tunnel¬boring in German coal mines (Fig. 1). These tests are performed with a tunnelborer of 2.6 m diam in an upper [ ]

Jan 1, 1979

By John D. Morton, J. H. LaVerne Palmer, Douglas J. Belshaw

An extensive programme of ground instrumentation and observation was carried out for the West Duff in Outfall Sewer tunnel project prior to and during construction, to establish the performance characteristics of the rock through which the tunnel and appurtenant openings were dug and to examine the nature of the lining-to-ground interaction. The existence of high horizontal residual ground stresses was confirmed, and values established by overcoring. Rock deformations and stress changes were monitored during tunnelling. Permanent stress and strain monitoring devices were set into the final lining and these are continuing to operate. INTRODUCTION The site is located on the north shore of Lake Ontario at Pickering, some 20 miles (32 kilometres) east of Toronto, Canada where a variable thickness of glacial or interglacial sediments overlies bituminous shale bedrock of. the Collingwood Formation which is lower Ordovician age. Approximately 50 feet (15 metres) of glacial cover exists at the shaft, though this thins abruptly at the regressing cliffed shoreline such that several small areas of exposed bedrock exist in the lakebed. The general location, overall geological section and detailed site plan and profile are illustrated in Figs.1,2 and 3 respectively. General properties of the rock as established during an extensive test drilling and site investigation programme are listed in Table 1, while stress determination by USER overcoring stress meter device are given in Table ll. These data formed the basis of analyses which were done to examine the intended outfall design, and to detail the construction procedure and the observational instrumentation programme.

Jan 1, 1979

By W. A. Heitbrink, J. D. Ashley, R. E. Gresh, J. A. Organiscak, A. B. Cecala

Many different types of mobile equipment used in surface coal mining utilize enclosed cabs to protect equipment operators. The overburden removal process is extremely dusty and can cause excessive exposure to respirable dust, especially crystalline silica. After equipment is used for years, many components of the enclosure deteriorate and its effectiveness is greatly reduced. This report discusses a cooperative research study performed on an Ingersoll Rand DM45E surface drill, retrofitted with a new Sigma pressurization and filtration system. Respirable dust concentrations were substantially reduced from 0.64 mg/m3 during pre-testing to 0.05 mg/m3 during post-testing with the new system, representing a 92% reduction in dust levels in the drill cab. This new system appears to be a very well-built and sturdy device, well-suited for the mining industry.

Jan 1, 2002

By Verya Nasri

The proposed Second Avenue Subway Project in New York City is approximately 8.5 miles long, up to a depth of 120 feet beneath grade and runs the length of the eastern side of the island of Manhattan from Harlem in the north to the financial district in the south. It will reduce overcrowding and delays on the existing parallel line, improving travel for both city and suburban commuters, and upgrading access to mass transit for residents of the East Side of Manhattan. This subway line will have 16 new stations providing transfers to the existing Metro-North commuter rail service and to New York City Transit subway lines and bus services. The first phase of construction includes two TBM rock tunnels 2.4 miles long and two new large and shallow rock cavern stations with clear span openings ranging from 70 to 100 feet and length in excess of 1000 feet with 615 feet center platform, coupled with low rock cover ranging from 20 feet to 40 feet. The design methodology for these large and shallow rock caverns consists of using well known empirical methods for initial estimate of support requirements and then two and three dimensional continuum and discontinuum analyses for verification of the selected excavation sequence and support system. This paper describes the analysis and design methodologies used for the two large and shallow rock caverns with insight into how to overcome the design complexities and construction challenges of the urban underground.

Jan 1, 2008

By S. K. Kawatra, H. Haselhuhn

"In many mineral processing applications it is necessary to know the isoelectric points of the various minerals in the ore to properly perform flotation and other mineral separations. However, current zeta potential analysis technology used to determine the isoelectric point of a particle suspension cannot deliver the isoelectric point of each individual mineral, just an average of the mineral system. Traditionally, individual isoelectric points have been gathered by testing pure, synthetic minerals. These values can vary widely depending on the mineral synthesis procedure and the water quality used during the isoelectric point analysis. A more robust approach for determining the actual isoelectric point of a particular mineral in a mixture of minerals is needed. This paper details a method for determining the isoelectric point of an iron oxide mineral in a siliceous iron ore. The method uses a laser scattering particle size analyzer and a pH electrode to determine the pH at which the liberated mineral particles begin to flocculate as pH is decreased. The pH at which the average particle size rises dramatically is the isoelectric point of the mineral with the highest isoelectric point in the ore. This measurement technique was used on natural hematite, goethite and siderite ores as well as a synthetic mixture of pure silica and pure hematite. The results for synthetic hematite mixtures were comparable to literature values.IntroductionRecently there has been an increased interest in the processing of low-grade iron ores (Bolen, 2014; Carlson and Kawatra, 2008, 2011, 2013; Halt et al., 2014; Halt and Kawatra, 2014; Haselhuhn 2012, 2013; Haselhuhn et al., 2012a, 2012b; Kawatra and Halt, 2011; Liu et al., 2014; Manouchehri, 2014; Sandvik and Larsen, 2014; Semberg et al., 2014). The zeta potential of iron ore minerals is a very important and often overlooked aspect of iron ore mineral processing. Zeta potential is the charge at the shear plane of a surface in an aqueous environment (Carlson and Kawatra, 2013). Many ores consist of a variety of minerals differing in zeta potential. This property of a particle surface in water is responsible for either keeping the particles dispersed from each other or flocculated to each other. This is important during many operations such as flotation, desliming and thickening. Zeta potential is primarily a function of the pH of the water and the mineralogy of the particles, though certain ions within the water can also have a significant impact (Haselhuhn, 2012). Consider the following situation: silica (SiO2) particles and hematite (Fe2O3) particles are suspended in an aqueous solution. These two types of minerals have drastically different zeta potentials throughout the pH spectrum (Esumi et al., 1988). In alkaline conditions, both types of particles exhibit negative zeta potentials and will tend to disperse from each other. In acidic conditions (between pH of 3 and 6), silica has a negative zeta potential while hematite has a positive zeta potential, so these surfaces will tend to be attractive to each other and the particles will flocculate and settle. This phenomenon is visually described in Fig. 1. The pH at which the two minerals begin to attract to each other, or destabilize, is near hematite’s isoelectric point. The isoelectric point is defined as the pH at which the surface has a net zero zeta potential (Carlson and Kawatra, 2013)."

Jan 1, 2015

By W. M. Ma, Daniel W. H. Su, K. Centofanti, Yi Luo, W. L. Zhong, Syd S. Peng

NTRODUCTION Surface subsidence monitoring is the most effective means for investigating the nature of, and developing the techniques for pre¬dicting the surface movement and deformation process. However, because of imperfection in survey equipment and field practices, the surface movement data collected from field survey are not error-free. Also due to lack of proper numerical techniques for computing surface deformation from the measured surface move¬ment data, a relatively large portion of the subsidence data col¬lected could not provide information other than surface movement. In a paper by Luo and Peng (1992), the sources and magnitude of errors in the measured surface movements using an electronic total station in subsidence survey are discussed. If the errors in the measured surface movement components are left untreated before calculation for deformation indices (i.e., slope, strain and curva¬ture), the errors will be carried over to the deformation indices and enlarged if improper numerical procedures are used in the calcu¬lation. It should be noticed that in protecting structures affected by ground subsidence, accurate surface deformation indices are much more important than surface movement. In order to improve the accuracy of the collected surface movement data and the calcu¬lated deformation indices, a number of numerical procedures are also proposed in the same paper. The proposed techniques include: a data smoothing technique for data pre-processing; and a number of numerical methods and/or procedures for calculating surface deformation indices from the measured surface movement data. DATA SMOOTHING Because of various factors, the measured surface movement data always contain errors, small or large. In order to better utilize the collected data, a data smoothing method is proposed to correct the errors in the measured movement data. The method uses the same concept as the influence function method (e.g., Knothe, 1957) on which many existing subsidence prediction methods are based. The data smoothing method makes necessary corrections on the measured movement for the point of interest according to not only the measured movement at this point but also those at the surrounding points. The contribution of a surrounding point in making the correction for the point of interest is inversely propor¬tional, in exponential form, to the distance between them. The new magnitude of a movement component at the point of interest (Zi*) is calculated by

Jan 1, 1992

By Peter K. Achireko, Samuel Frimpong

Design and optimization of open pit limits are of paramount importance because they provide information for evaluating the economic potential of a mineral deposit and for developing short and long range mine plans. Many algorithms and their modifications have been used to design and optimize open pit limits. These algorithms have provided mine planning engineers with pertinent information in designing, optimizing and extracting ore reserves by open pit technology. However, they do not address the random field properties associated with the ore grades and reserves and commodity prices, and thus, fail to yield the truly optimized pit limits in any time horizon. In this paper, a new algorithm, MCSIMFNN, which overcomes these limitations is proposed and used to optimize open pit limits. The random field properties of the ore grade and reserves have been modelled using the modified conditional simulation based on the best linear unbiased estimation and local average subdivision techniques. Artificial neural networks are used to classify the blocks into classes based on their conditioned values. The error back propagation algorithm, in the neural networks, is used to optimize the pit limits by minimizing the desired and actual outputs error in a multi- layer perceptron under the pit wall slope constraints. The optimized pit value obtained by this algorithm has been compared to that from the Lerchs-Grossman's algorithm in a case study. The results are the same, but in random multivariable states, the MCSI MFNN algorithm is the most suitable for pit optimization. The method is also fast since it mimics the operation of the brain in the solution of the pit optimization problem.

Jan 1, 1996

By M. Sengupta

Vast reserves of oil shale occur in the Green River formation in Colorado, Utah, and Wyoming. The room-and-pillar mining method is applied to flat-lying sedimentary deposits. Important elements in mine design include mine orientation, vertical location of the mining zone, selection of roof horizons, room span and pillar size, barrier pillar size, panel dimension, and layout of mains and submains.

Jan 1, 1988

By R. J. Matetic

Mining operations have long been accused of causing a disruption to local, domestic and agricultural water supplies. More recently, concern for water supplies has increased with the advent of high-extraction mining techniques, namely longwall mining. Theoretically, any water bearing zone in the overburden above a high-extraction mining operation may be affected by mining. In some cases, a confining bed may be fractured causing a loss of water to a particular zone. In other cases, increased fracture permeability may enhance the ability of an aquifer to transmit and deliver water. Unfortunately, only a limited amount of studies have been conducted that characterize hydrologic changes and also quant1fythe magnitude of mining-induced subsidence. The U.S. Bureau of Mines conducted such a study at a mine site located in Greene County, PA. A total of 8 water wells were drilled and hydrologic parameters such as specific capacity, transmissivity and well yield were determined both before and after mining. Electronic water level recorders were installed on each water well to provide continuous observations of water level fluctuations.

Jan 1, 1990

By T. H. Eyde

Worldwide production of natural zeolites during 2001 was estimated to be about 3.5 Mt (3.85million st). Construction and agriculture continued to be the major consumers. Estimated production in North America during 2001, including the United States, Canada and Mexico, was about 40 kt (44,000 st). In the United States and Canada, the zeolitic tuffs are ground, extruded or modified for use as adsorbents, desiccants, ion-exchange media and carriers. In Mexico and the rest of the world, the zeolitic tuffs are cut into dimension stone that is used in construction. Zeolitic tuffs are usually composed of the minerals clinoptilolite, mordenite or both. They occur in a variety of colors and are easy to cut and shape. And they have low thermal conductivity. This construction application is classified with dimension stone rather than with chemical and agricultural uses.

Jan 1, 2002

By Leslie S. Rubin, John C. Roberge, Mackenzie Burnett

A self regulating helical inducer has been developed and tested for dry injection of coarse or fine solids into a hydraulic pipeline. This centrifugal pumping device has also been modified and tested for use as a boost pump in medium and long distance pipeline haulage systems. The helical inducer has been operated as an integral component of a slurry injection vehicle. This compact, low profile vehicle also includes crushing and screening components, solids feeding components, a track drive system for mobility and is run by a single operator. The helical injector and boost pump operate without speed and flow controls allowing for the practical hydraulic transport of excavated materials.

Jan 1, 1983

By R. M. Quinlan

The coal industry in the United States has undergone significant economic changes during the past six years. The price of coal remained relatively constant from 1950 to 1969 (See Figures 1 and 2). Steam coal prices tripled and metallurgical coal prices doubled from 1969 to 1974. This price structure has created a new economic environment for coal preparation. Contributing factors to these price trends include: ? Coal Mine Health and Safety Act of 1969 ? Mid-East oil embargo of 1973 ? United Mine Workers of America contract agreements ? Productivity decrease (tons per man-day basis) ? Environmental Protection Agency regulations The increased value of coal justifies additional capital investment in cleaning facilities to optimize yield. Current trends include recovery of existing slurry ponds and recleaning of refuse. Coal preparation plant product yield and quality must be evaluated in terms of the amount of capital expended and cost of operation. Therefore, it is advantageous to optimize the plant product based on clean coal selling price and rate of return on investment.

Jan 1, 1976

By P. A. Tuzinski, L. J. Dahl, N. R. Adamson, S. E. Brink, R. L. Blake

The US Department of the Interior, Bureau of Mines is developing a process to selectively extract manganese from oxide ores as part of its in situ mining research program. The Bureau is conducting site characterization studies of two manganiferous iron-formation deposits. These studies include: drill core, regional stratigraphic relationships from the existing geologic database, ore body geometry, geologic structure, hydrologic conditions, accessibility of ore minerals to leach fluid, surface subsidence potential and data collected from laboratory leaching experiments. This information is being used to evaluate the technical, environmental and economic feasibility of in situ mining of manganese for these two deposits. This paper will focus on the stratigraphy, mineralogy, ore textures, fractures, permeability and porosity as they relate to in situ mining.

Jan 1, 1994

By Charles J. Hass

INTRODUCTION Deformation measurements are some of the simplest and most useful measurements that can be made by the mining/rock mechanics engineer in assessing the sta¬bility of openings in rock. A number of tools and tech¬niques are presently available. This chapter will de¬scribe the most common instruments, their application, and present the equations needed for data reduction. MECHANICAL STRAIN GAGE Description of Instrument A mechanical strain gage of the Whittemore type shown in Fig. I is a useful instrument for measuring deformations of pillars, sidewalls, and roofs of under¬ground mines. Measurement gage lengths typically range from 51 to 254 mm (2 to 10 in.), and the dial indicator reads to 0.0025 mm (0.0001 in.). The instru¬ment measures the deformation between precision gage points which are anchored in the rock. The anchor points are typically grouted in small holes drilled 12.5 mm (1/2 in.) or so deep into the rock. Strain a is calculated from the measured deformation AL with the equation [ ] where L is gage length. A necessary accessory for the instrument is a master bar normally made from invar steel having a low co¬efficient of thermal expansion. This bar allows one to check the instrument for changes in the mechanical zero point and to correct for temperature effects on the measuring instrument. The instrument is available from Soiltest, Inc. for a cost of approximately $340; the cost of the master bar is approximately $55; and nonreusable brass inserts which are anchored in the rock are nominally priced at $0.27 each. All prices are for 1978. Applications Two classes of applications may be considered, one where only one measurement direction is involved and the second where three measurement directions are em¬ployed. Applications where only one measurement di¬rection is necessary include: monitoring crack or frac¬ture separation or shear movement with anchor points on opposite sides of the discontinuity; measurement of vertical strain in a pillar or sidewall; and measurement of steel support deformations with anchors in the steel members. The more general application involves a strain ro¬sette consisting of three measurement directions which for convenience are oriented 1.04 rad (60°) apart to form an equilateral triangle as shown in Fig. 2. Strains in the three measurement directions [ ]

Jan 1, 1982

By John T. Cantwell

INTRODUCTION The process engineer usually is responsible for the design operating philosophy and/or day-to-day operations of a process. Since instrumentation is an integral part of the operation, it is essential that engineers understand the general capabilities of the different types of control equipment available. Many "noncontrol" engineers have become involved with instrumentation for machinery monitoring and control as well as other plant applications. The advent of the microprocessor has led to significant changes in control, both in systems configurations and man-machine interfaces. Today's concept is called simply "distributed control." What is distributed control? Distributed control is exactly what the name implies; the control system is divided into several functional segments and spread out to cover a process. The systems are distributed for physical, functional, and risk reasons. Before delving further into the specifics of distributed control, let's look at the evolution of control systems to see how we got here. Instruments initially were located near measurement and control points in the field. Operators physically had to go to the instrument to change setpoints or take measurements. As processes became more complex, it became evident that a central control area was required. This allowed an operator to monitor and control many variables. The operator's effectiveness was increased dramatically, which resulted in greater efficiency, better quality control, and lower personnel requirements. At the same time, plants became much larger, control applications became more complex, energy became expensive, and the industry became more competitive. All of these factors placed pressure on process and production engineers to get the most for the money. The result was a continuing push to put more instrumentation into a central control room to maximize efficiency and productivity and minimize manpower. This chapter deals in some detail with devices for measuring physical and chemical properties of coal; devices for measuring the weight and weight-rate of flow of coal; devices for the monitoring and control of conveyor systems, solids inventory, fluid flow, liquid level, density, and specific gravity. These instruments have a multitude of uses throughout a coal preparation plant. The discussions cover advancements in "on-line analysis," nuclear control devices, and distributed control using microprocessors, mainframes, and soft-

Jan 1, 1991

By John C. LaScola, Gerald L. Finfinger, Michael A. Trevits

Methane gas is an ever-present problem facing the underground coal mining industry. Mine operators are mandated by law to maintain safe concentrations of methane gas within the mine environment. Ventilation is the method of choice used by all mine operators to reduce gas concentrations. When gas emissions are such that ventilation alone cannot control the gas, methane drainage methods must be applied. In the 1970’s, there was a concern that unprecedented gas emissions would be experienced as mine operators began new developments in the deep and gassy Blue Creek and Pocahontas No. 3 Coalbeds. Such concern was well founded as significant gas volumes are being emitted as these mining operations mature. In 1971, the U.S. Bureau of Mines began to tabulate and track the change in mine emissions. These data were extracted from the underground coal mine quarterly air quality-quantity inspections performed by the Mine Safety and Health Administration. At that time, approximately 6560 Mm3/d (231.7 MMcfd) of gas were emitted from 430 underground coal mines. It was determined however, that the mines emitting less than 2832 m3/d (100 Mcfd) contributed only 2.1 percent of the total daily gas flow. In 1988, underground coal mines emitted 8350 Mm3/d (294.9 MMcfd) from 487 mines. This report evaluates the changing nature of U.S. mine gas emissions over the last 18 years.

Jan 1, 1991

By Wenhua Wan, Jan M. Mutmansky

Many concerns have been expressed worldwide regarding the use of diesel equipment in underground mines due to the potential health risks associated with diesel particulate matter (DPM). In assessing the risk to the health of miners and designing control strategies for DPM, it is important to know the concentration of DPM in the working areas of a mine. In some mines, significant stratification occurs due to the characteristics of the diesel exhaust, affecting exposure and the ability to measure DPM concentrations accurately. This study outlines some of the concentration profile data obtained during sampling at three mines where diesels were employed. Mine #1 (a gold mine) employed large openings in which a diesel-powered roof bolter was used. Mines #2 and #3 are both room-and-pillar operations with varying conditions. Mine #2 is an experimental mine where two stationary diesels were utilized for sampling purposes, while Mine #3 is a traditional evaporite operation using two mobile diesel vehicles for section haulage. These field studies indicated that some level of stratification occurred in all the mines, but the stratification was not as pronounced in the case of Mine #2 due to the complex pattern of exhaust emissions generated by the vehicles. The stratification seemed to depend on the distance from the vehicle, the mine air velocity, whether the vehicles were moving or stationary, and whether the exhaust was diluted by equipment design features. The concentration of DPM was generally higher at samplers located near the roof and lower at samplers located near the floor. However, this was not found in all cases. This paper provides conclusions on how knowledge of stratification patterns can be utilized in sampling and control of DPM in mine atmospheres.

Jan 1, 1997

By W. David Tyler

Any mining or engineering-construction excavation that extends below the water table must be dewatered. In many situations, the ground is of low permeability or the workings extend only a short distance below the water table. So water removal can be handled easily and economically by using mobile centrifugal pumps. However, there is an increasing number of mines that have a continuous high flow of water into the workings. Controlling this flow can significantly increase the cost of ore production. Successful implementation of any major dewatering scheme will ultimately rely on a clear understanding of the local geology. This understanding is necessary before an interpretation of ground water conditions can be made. It will dictate which dewatering methods are feasible. Once the geology and the ground water system are known, the scope and timing of the dewatering measures can be varied with the mine plan. Ground water modeling can assist in optimizing the dewatering system, though the precise objective of each model should be clearly defined. Production wells must be sited and drilled so that individual well efficiencies are high. Any lost efficiencies will translate into higher operating costs. Each well must be designed for maximum long-term control of the water table, and pumps sized to operate under continually changing heads. Finally, the investment in each production well must be protected during the mining process.

Jan 1, 1991

By Dennis A. Fenton

This paper presents some techniques and data required to design large ball mills. The advent of larger size mills leads to consideration of the gearless drive as a practical solution to utilize large horsepowwers. The particular shell structure under consideration is subjected to thermal as well as magnetic loads. The magnitude of the inertia, magnetic and shell temperature characteristics have a very significant effect on the design and performance of the hydrodynamic pivoted shoe bearing. Particularly since these bearings have lower frictional resistance properties than hydrostatic trunnion tee rings. The structure of the mill is designed for long life. Parameters involved with the fatigue life of the structure are discussed together with some of the more important aspects of the design.

Jan 1, 1975

By A. Yehia

Fluoride activation has been evaluated by Hallimond-tube flotation of collophanite in terms of fluoride concentration, conditioning time, pH, and temperature. The results reveal that efficient oleate flotation of collophanite can be achieved by fluoride activation. Fluoride adsorption by collophanite as a function of fluoride concentration, temperature, pH, and crystal structure suggests that, at low fluoride concentration, a fluoroapatite-type compound may form on the collophanite surface by chemisorption of fluoride ions at calcium sites; at high fluoride concentration, calcium fluoride ap¬pears to form at the collophanite surface invovling a surface-precipitation phenomenon. The formation of CaF2 on the surface of fluoride-treated collophanite is further substantiated by the FTIR spectroscopic measurements, which clearly shows a metathetic exchange with phosphate from the collophanite lattice during surface precipitation process.

Jan 1, 1986