Search Documents

By Paul Headland

The Washington Suburban Sanitary Commission (WSSC) has recently completed design for the Bi-County Water Tunnel Project. The project will include a 10-foot diameter, 5.3-mile long hard rock tunnel located within the Piedmont Physiographic Province in Montgomery County, Maryland. The rock formations present along the alignment are comprised of igneous and metamorphic lithologies. This paper presents the steps taken to characterize the complex geology along the tunnel alignment into a single ?Engineering Unit? based upon the intact rock and rock mass properties. The Rock Mass Rating (RMR) system is planned to be used as the basis for dividing the ground into three ?Excavation and Support? classes. This RMR approach was selected to establish contractual baselines as presented in the Geotechnical Baseline Report (GBR) and is intended to facilitate management of the ground support characterization during construction.

Jan 1, 2008

By A. K. Bakshi

In cold regions, rinsing of spent cyanide from leach heaps is stopped during winter and is resumed again after the snow melts. The effect of this idle time on the overall removal process was studied in this experiment. Samples were collected for rinsing tests from one heap at a gold mine near Fairbanks, Alaska. Continuous and interrupted rinsing of this sample were carried out in test columns. The rinse solution was analyzed at regular intervals to determine the rate of cyanide removal from the solids. It was found that total cyanide concentration per rinse cycle for interrupted rinsing test was higher than for the corresponding continuous rinsing test. As a result, interrupted rinsing required less rinsing cycles than continuous rinsing.

Jan 1, 1995

By G. Triantafillou

The aim of this paper is to present the progress of the plan of the Greek Public Power Corporation S.A. (PPC S.A.) at the Lignite Centre of Megalopolis in Peloponnesus (southern Greece) to manage impacts on local communities in areas affected by its activities during the lignite mining operation and post-closure. The reclamation works in the waste dump areas of the mines that constitute the Megalopolis Lignite Centre, concerning the utilization of waste dumps for infrastructure community projects constructions are discussed. Moreover, selected environmental indicators concerning land use and closure and rehabilitation are presented.

Jan 1, 2008

By R. J. Sweigard, T. Beckman, C. T. Justice, E. D. Thompson, T. C. Hopkins

As a means of permanent disposal, fine coal refuse is often pumped as a slurry into surface impoundments. As the available volume is filled, the embankment heights are frequently increased. The additional embankment material is often placed upon consolidated fine coal refuse. There has been concern about the long-term effect of consolidation of this material at or above the liquid limit on its shear strength. A laboratory investigation was performed using three different types of fine coal slurry taken from central Appalachian coal-preparation plants. The refuse was consolidated in 3-m (10 ft) Plexiglas columns under incremental amounts of surcharge loading. The incremental loads were designed to simulate the effect of increasing the height of a refuse embankment on top of the consolidating coal slurry. After the refuse in the columns had consolidated for several months, the columns were cut apart, and triaxial tests were performed on both the consolidated and unconsolidated material for comparison of their shear-strength parameters.

Jan 1, 1998

By Robert Seal, James J. Rytuba, Michael P. Hunerlach, Roger Ashley, Dean Enderlin

Cessation of open pit mining in 1996 at the McLaughlin hot-spring type gold deposit has resulted in the development of two pit lakes that will be managed as permanent lakes with a total storage capacity of 10,000 acre-feet. The south pit lake developed from alkaline ground water infiltration and had an initial pH of 7.2. It contained high concentrations of boron and chloride, indicating that it consisted of a mix of meteoric and evolved connate waters. Numerous carbon dioxide gas vents were present initially in the shallow south pit lake, but as the pit lake increased in depth, gas venting ceased and carbon dioxide is retained in the lower layer of the chemically stratified lake. Continued increase of dissolved carbon dioxide in the lower layer increases the potential for a limnic eruption. A chemocliie occurs at a depth of 47 m. The upper layer of the lake has lower pH, temperature, and conductivity than the lower layer. Effluent from ore and waste rock piles directed into the south pit lake has contributed to high levels of antimony, arsenic, cobalt, copper, mercury, nickel, and zinc. Iron oxyhydroxide is abundant in mine effluent that enters the pit lake and adsorption onto this phase has lowered the arsenic and antimony concentrations. The north pit lake formed primarily from winter surface runoff. The acidic water, pH 4.56, initially had high concentrations of cobalt, mercury, and nickel derived from weathering products of pyritized serpentinite and shales. Buffering by wall rocks has established a slightly alkaline pH of 7.62. The concentrations of trace metals in the north pit lake have substantially decreased due to continued dilution of the lake by surface runoff and remediation of parts of the pit walls that have been covered by backfill.

Jan 1, 2000

By P. Somasundaran

The use of chemical additives in ultrafine grinding will be reviewed in this paper for the case of grinding of quartz in solutions of surfactants and inorganic electrolytes including some dispersants under different conditions of pH and ionic strength Mechanisms are examined by correlating the grinding effects with those obtained for the influence of these chemicals on zeta potential, pulp fluidity and flocculation/dispersion characteristics The analysis suggests grinding depends mainly on the state of aggregation of the ground products inside the mill and pulp fluidity Implications of the observed effects on ultrafine grinding in general are discussed

Jan 1, 1983

By B. Hearn, O&apos

Falconbridge, Ltd. operates six mines (the strathcona, Fraser, Lockerby, Onaping, East and Kidd Creek) in the Sudbury and Timmins districts of northern Ontario (Fig. 1). These mines vary in depth to approximately 1500m and experience a wide variety of ground conditions. Problems of greatest concern include rockbursting, backfill pillar stability, wall and pillar stability, and the use of cable anchors. A study was initiated approximately two years ago to identify how numerical models could aid in the examination and possible understanding or solution of these problems. This paper discusses the use of numerical models at Falconbridge and describes a case history of their use in examination of rockbursting at the Strathcona Mine.

Jan 1, 1988

By Adrian Coombs, Paul Magowan, Derek Zoldy

Continued development and intensification are fuelling the urgent need for new trunk infrastructure within The Regional Municipality of York and throughout the Greater Toronto Area. Permitting of these projects is increasingly subject to public scrutiny to severely restrict dewatering through construction technologies and the requirement for a comprehensive and effective Environmental Management Plan. Three current projects: one on the York Durham Sewage System and two in the City of Toronto 1.Conventional Design, Tender, Award: 4,150m (13,600 ft.) 2.7m (9 ft.) finished interior diameter soft ground tunnel for York Region’s YDSS Interceptor Trunk Sewer 2.Negotiated Contract: 3,800m (12,500 ft.) 3.5m diameter (11.5 ft.) rock tunnels for Enwave’s environmentally sustainable and innovative chilled water system in downtown Toronto 3.Conventional Design, Tender, Award: 2,200m (7,200 ft.) 3.3m diameter (10.8 ft.) rock tunnel for reinforcement of Hydro One’s primary hydro feed in the downtown core of Toronto These projects exemplify issues such as: EPB tunnel and sealed shaft technologies Substantial permitting requirements associated with dewatering Mitigation of rock creep Congested downtown rights-of-way Deep shafts and confined working compounds Unique scheduling and cost benefits when Owner, Contractor and Consultant can work together cooperatively.

Jan 1, 2007

By S. K. Kawatra, T. C. Eisele

Pyrite depression is of great interest in sulfide mineral flotation, where pyrite is a common gangue mineral. Since the floatability of pyrite is a function of the pH and a variety of other chemical factors, pH control is a critical part of sulfide flotation circuits. A wide variety of pyrite-depressing chemicals have been studied and used in sulfide- mineral processing, with considerable success. However, there are certain applications where there are still no satisfactory pyrite depressants, and even when suitable depressants are available, there is always a need for less-expensive reagents. Microorganisms, such as the bacteria Thiobacillus ferrooxidans, are known to depress pyrite flotation. However, the dependence of the depression on the type of organism or on suspension pH is still being determined. In this study, the relative effectiveness of various microorganisms, and the effect of pH, has been examined. Screening tests using microflotation showed that every microorganism tested was capable of depressing naturally hydrophobic pyrite at acidic pH. Larger-scale experiments with two of the screened organisms and two different pyrites showed that microorganisms are very effective depressants at acid pH, but are largely ineffective at neutral and alkaline pH where the pyrite surface is not naturally hydrophobic.

Jan 1, 1994

By William A. Kneller

A considerable range of composition exists in rocks that have been described as chert, jasper, or flint. Their composition may be opaline, chalcedonic, quartzose, or mixed. Certain cherts, when incorporated in concrete, are known to possess nondesirable thermal and chemical properties. The inability of chert to withstand thermal shock above the freezing temperature of water is an example of such a property. Cryothermal reactions may cause disintegration of concrete, due to repeated cycles of freeze and thaw. Thermal properties are significant because small temperature changes may cause inordinate expansion and resultant fissuring of concrete. Freezing of entrained water in chert may cause excessive physical failure in concrete. Some cherts react chemically with alkalies liberated during the hydration of the cement, with resultant cracking and deterioration. Sources of concrete aggregate in Ohio have been viewed with suspicion because they contain considerable chert derived from Middle Devonian and Pennsylvanian carbonate rocks. Light-colored porous cherts from the Middle-Devonian Colum- bus Limestone exhibit the least freeze-thaw durability of the samples studied. Denser cherts may also yield to freeze-thaw stresses, but tend to be more susceptible to thermal shock. Cherts rich in opaline and chalcedonic silica usually exhibit alkali-aggregate reactivity.

Jan 1, 1966

By Eric K. Albert

The permit generation and review process represents both a time consuming and expensive task for industry and government alike. Changes in regulations and in review procedures cause additional delays. This leads to potentially higher costs of doing business and the extension of time for a project to lie started. This paper describes the motivation and methodology of applying an expert system to function in the role of a permit reviewer. The problems of representing the knowledge of the reviewer and regulatory criteria are illustrated. Futhermore, the selection method for the expert system shell is addressed. Finally, a sample review is demonstrated to show the results of applying this artificial intelligence method to the process of permit review.

Jan 1, 1989

By J. L. Yordan, T. Hilderbrand, R-H Yoon

High brightness clays are produced from Georgia kaolin by flotation. Fatty acids are used commonly as collectors for anatase, which represents the major colored impurity in the crude. This process requires activation of the minerals with divalent cations such as Ca2+, in which case proper control of the activation step is crucial to the success of the flotation process. In the present work, laboratory tests have been conducted using alkyl hydroxamates as the collector for anatase. A major advantage of using hydroxamate is that this new collector requires no activator. The laboratory tests show also that the hydroxamate collectors produce consistently better products with higher yields from a variety of kaolin clays.

Jan 1, 1994

By A. C. T. Bigg, A. F. Colombo, A. R. MacPherson

The step-by-step study of the Stronsay ores follows the testwork through the initial determination of Bond Rod and Ball mill work indices, the MacPherson Autogenous work indices and the production of a preliminary flowsheet. These results are then used to design a pilot plant program to test the effectiveness of fully autogenous primary and secondary grinding and to determine the feasibility of controlling feed rate by the use of variable speed mill drive and/or varying the mill load. A final flowsheet is recommended with mill sizes and power requirements.

Jan 1, 1992

By James M. Johnson, David Landriault, Frank Palkovits

The term “Paste Technology” was first used in the late 1980’s. It was used to describe a high fines (15 wt% or greater minus 20 microns), low water content backfill material that could be transported underground through a borehole/pipeline distribution system (4” to 8” dia.) at a yield stress similar to fresh concrete (100 to 400 centipoise). This “Paste Backfill”, unlike slurry transported backfills does not segregate into separate solid and liquid phases at low pipeline transport velocities or upon disposal into the underground stope. Paste backfills can consist solely of fine material, or can include fines plus sand and aggregate similar to a concrete mix. Pipeline transport of paste requires that sufficient fine material (minus 20 micron content) is contained within the mix to lubricate the pipeline walls to create a plug flow condition. For concrete, the fine material is supplied through the cement addition to achieve high compressive strength. For paste, the fine material is generally available in large quantities in the form of mill tailings. The paste tailings can be transported underground for use as backfill or discharged on the surface in a tailings management facility (TMF). This natural abundance of fine grained material is not exclusive to mine tailings but is common to many waste streams in many different industries. This makes the disposal of many waste materials very amenable to paste pipeline transport and placement as a non-segregating slurry. The potential use of paste technology for a wider group of waste materials was realized by these authors and others over two decades ago. Through the effort of this small group the use of paste technology has expanded over the years to become recognized as a low cost, environmentally superior, and technologically controllable method of transporting and placing specific material waste streams with a low water content and high placement density. The high yield stress nature of a paste also lends itself well to the blending of one or more coarse waste materials into the fine waste material paste stream. This allows all the waste materials to be transported by pipeline, increases their placement density; decreases the supernatant release/treatment, reduces contaminant mobilization, hydraulic conductivity and oxygen/water reactivity through encapsulation in the paste matrix. The following paper describes the present state-of-the-art use of paste technology in the world today. It also describes future uses of the technology that are under development and speculates on the overall use of the technology for waste management in the future.

Jan 1, 2005

By Yuanhong Qi, KUN CUI, Tao Fu, XUNFU WANG, Yingyi Zhang, Jie Wang, Junmao Qie

Indonesia is the world’s largest supplier of nickel ore, with its nickel laterite resources mainly distributed in the Moluccas and Sulawesi regions. However, there is scant research on the mineralogical characteristics of nickel laterite deposited in southeast Sulawesi, Indonesia. This study aims to investigate the mineral phase structure, chemical analysis, thermal properties and element distribution characteristics of the middle and lower part of the rotten rock zone located in the southeast Sulawesi ophiolite belt.

By Zoltan F. Oszter

The frictional resistance to motion of a belt conveyor has always been a subject of intensive studies and research by engineers throughout the years. Numerous informations have been developed by analysing series of field tests on belt conveyors of different characteristics and carrying different materials at various capacities. Within certain limits of weight per unit length and tension, the theoretical considerations and the analysis of the field tests, both in the US and abroad, resulted in the development of similar formulas. In general these formulas are safe to use up to the following limits:

Jan 1, 1977

By Barry D. Simmons

The Millenbach copper-zinc orebody is an ideal Canadian example of a stratabound base metal deposit in volcanic rocks. The mine, operated by Lake Dufault Divison, Falconbridge Copper Ltd. is located five miles north of the city of Noranda in northwestern Quebec. The deposit occurs within an Archean volcanic sequence which forms part of regional acidic volcanic center within the Abitibi greenstone belt. Preproduction ore reserves totalled 2,075,000 tons grading 3.5% copper, 3.6% zinc, 1.1 ounces per ton silver, and 0.02 ounces per ton gold. Stratabound lenses of massive sulphides together with underlying stringer sulphides are closely associated with a dome of quartz-feldspar porphyritic rhyolite approximately 3000 feet below surface. The paper describes the presently known geology of the deposit and includes documentation of sulphide mineralogy and textures as well as sulphide/ host rock relationships. The stratigraphy, petrography and chemistry of the volcanic host rocks are described with emphasis on the alteration intimately associated with the sulphide bodies. Although the volcanic stratigraphy is complex within the mine area, the presence of only low-grade metamorphism and the relative lack of structural deformation allow detailed interpretation of geological history. Presently recognized evidence strongly suggests that the sulphides were deposited at and near sea-floor, by hydrothermal solutions. The dome of porphyritic rhyolite appears to have been the most significant factor controlling sulphide localization.

Jan 1, 1975

By Richard J. Fantel

This paper addresses the impact of declining world rutile resources upon the production of titanium products and their asso¬ciated costs. Titanium is used primarily for the production of pigments; in its metal form it is considered a strategic and critical material to the U.S. defense and aerospace industries. There are two major mineral sources for titanium: ilmenite and rutile. Both these mineral types can be used to produce titanium pigments. Only high grade titanium concentrates, such as rutile, high-grade ilmenite, and synthetic rutile (which is produced through further processing of ilmenite), can be used in the production of titanium metal. This paper draws upon the data and analyses of a recent Bureau of Mines Minerals Availability Program appraisal that evaluated the international availability of titanium from market economy countries. The paper will show that production from economic rutile mines will decline sometime after the turn of the century and that rutile shortages could be alleviated by production from other high-grade titanium resources such as higher cost rutile deposits and anatase deposits, or through an increase in world synthetic rutile capacity.

Jan 1, 1984

By R. W. Reisinger

An historic underground copper mine in Wyoming is discharging neutral but copper-laden water into a pristine creek. The EPA-deferred site qualifies for reclamation by the Wyoming Abandoned Mine Land (AML) program. The cleanup goal is to restore the discharge so that the creek can eventually support a trout fishery. Hydrological and geochemical investigations underground have suggested two sources of mine water: one clean and the other containing copper. Results of bench-and pilot-scale tests support the viability of using low-cost passive treatment techniques to reduce copper concentrations in the near-freezing mine discharge.

Jan 1, 2000

By John C. Edwards, Robert C. Bates

Results are given of a mathematical study by Bureau of Mines personnel of overpressurization ventilation effects in underground uranium mines. The mathematics and computer codes make it possible to analyze many facets of transient and steady-state radon diffusion with Darcy flow. Rapid changes in radon flux occur after imposing a pressure differential across the model. Flux into the model mine drops to near zero and then increases to the steady-state level, while the sink flux increases rapidly and then drops slightly to the steady-state level. Magnitudes of mine flux decreases and sink flux increases are dependent upon the distance from the mine to sink, permeability, and amount of overpressure. Current work on more complex models is also described.

Jan 1, 1981