Search Documents

By John F. Schat, T. William Thompson

Laboratory data on the time-dependent compaction of porous rocks are presented, and various attempts to model this behavior are described. These lead to a discussion of the problems that arise in using laboratory data to estimate long-term effects. A method is suggested for combining laboratory data with information from the geologic record to estimate long term effects.

Jan 1, 1986

By D. N. Thompson, R. L. Sayer, K. S. Noah

Economical remediation of acid rock drainage (ARD) at secluded high-altitude western ore mines is difficult given the current treatment technology. Several passive-engineered systems that are based on wetland technology were tested in the laboratory with three western ore mine ARDs (Co, Cu and Fe mines) and with a copper leachate effluent. These systems used well-weathered lodgepole pine sawdust as the sole carbon source and mud from a pond at one of the mine sites as the source of sulfate-reducing bacteria (SRB). Simple one-pass flow-through systems removed 44% to 99% of the vari¬ous heavy metals front the Co and Cu mine ARDs and increased the pH from 3 to 7 after 28 days of SRB acclimation with a five-day residence time. Carbohydrate utilization rates were generally low, except for one 437-day run, which consumed 25%, 30% and 21 % of the cellulose, hemicellulose and lignin, respectively. Initial pH, amounts of toxic heavy metals and the degree of predegradation of the sawdust were found to significantly affect both remediation potential and acclimation time. Engineered SRB systems, alone or in combination with other passive technologies, offer promise for the economical remediation of western US ore mine ARDs.

Jan 1, 2000

By Norman D. Harte, George W. Holl

The development of the most important tool used in Site Testing is reviewed briefly and the application of the information gained is described. The operation of Site Testing and pregrouting of underground excavations is dealt with in detail. Practical experiences (and pitfalls into which the inexperienced might fall) are recorded. But for the application of Site Testing and grouting of shafts, tunnels and other excavations, vast areas of the present goldfields in South Africa would remain unexploitable.

Jan 1, 1981

By T. H. Jones

Fall of ground is a leading source of worker injury and fatality indicating a persistent need for ground monitoring technology. The HRTMM is an experimental convergence monitor utilizing a digital camera and custom software to track the position of one or more lasers across the target. Apparent laser movement is proportional to target convergence. The HRTMM was installed in an underground mine near active operations to test its response to the mining environment. This included intense blasting vibration and mine fog. Results and potential of the new monitoring technology will be discussed.

Jan 1, 2008

By C. Roldan, C. Garcia, J. D. Miller, C. L. Lin

The ultimate recovery in a heap leaching operation is related to the degree of exposure of the valuable minerals in comminuted particles. Recently, high-resolution cone beam x-ray microtomography (XMT) has been used to determine this parameter. XMT technology consists of examining the extent of mineral exposure for each size fraction of ore in 3D, then, by algebraic calculations, the ultimate recovery can be estimated for different particle size distributions (PSD). To confirm the usefulness of the XMT technology for mineral exposure analysis, column tests were performed to determine ultimate recovery using three PSDs for two composites obtained from the copper heap leaching operation at Zaldivar-Chile.

Jan 1, 2003

By Maurício L. Torem, Isabella A. Scorzelli

Taboca Mining is one of the largest producers of tin in the world. In its pilot plant, significant amounts of a middling of 90% xenotime (YPO4) and 10% zircon (ZrSi04) are produced. Until now, these minerals of this ore body could not be separated successfully. This paper presents some aspects of the fundamentals of xenotime and zircon flotation with anionic (fatty acids) and cationic (amine acetate) collector, as well as the influence of the superficial leaching of the minerals with cold HCI and HNO3 on the floatability. The mineralogical studies showed that both minerals are optically liberated in -212+106 µm size fraction. Surprisingly, SEM analysis indicated that both xenotime and zircon contain very small inclusions (1-5 µm) of thorite (ThSiO4). On the other hand, zircon is fairly metamictizated giving rise to malacon. Zeta potential tests showed that the isoelectric points of xenotime and zircon correspond to a pH value of 4.5 and 4.7, respectively.The pretreatment with HCI and HNO3 displaced the isoeletric point (IEP) of the minerals to the left. The microflotation tests indicated that the floatability of both untreated and treated minerals are quite similar in the presence of the collectors studied in this work. Adsorption mechanisms are also suggested.

Jan 1, 1995

By Vasiliki Founta, Andrew J. Whittle

"This paper describes the development of a 3D finite element model for predicting ground movements caused by construction of 7.1 m diameter twin bored tunnels for the Crossrail project in London using Earth Pressure Balance (EPB) machines. The model uses the commercial FE code, Plaxis 3D, to represent the face pressure, conical shield, grouting process and activation of precast segmental concrete lining systems through a set of boundary conditions that advance through the soil mass along a prescribed trajectory. Soil behavior is described using the Mohr-Coulomb soil model with input parameters calibrated from laboratory element tests. The analyses focus on the performance of the EPB tunneling machines in greenfield conditions beneath Hyde Park, where the tunneling occurs within deep layers of relatively uniform London Clay. The model predictions are in good agreement with surface and sub-surface vertical settlements measured at a well-instrumented section, but tend to overestimate the measured lateral displacements towards the tunnel. Ongoing studies are focused on the role of soil behavior and the approximations in FE model predictions of tunnel-induced ground deformations. Introduction Since their introduction in the 1970’s, closed-face Earth Pressure Balance (EPB) machines have become widely used for soft ground tunnel construction. The EPB design relies on a screw conveyor system to regulate the pressure of the excavated soil/spoil within the head chamber and hence control stability at the face of the machine. One of the key design issues in the application of EPB machines is to establish how control parameters, including the advance rate, face pressure and grouting processes (used to compensate for the tail void at the rear of the shield and to infill gaps between the precast lining rings and surrounding soil) affect and/or control the far-field ground movements. For closed-face systems, short-term deformations are associated with ground losses at the face, overcutting and ploughing of the shield and poor control of grouting in the tail void; while long-term deformations can occur due to consolidation and creep within the surrounding soil (and are closely connected to the seepage boundary conditions;e.g., Laver & Soga, 2012). The control parameters for advancing the EPB machine can have a significant effect on the magnitude and distribution of the far-field deformations. Therefore, analyses of the ground response to tunneling require accurate modeling of the soil stratigraphy and constitutive behavior as well as the construction process. Finite element (FE) methods have been used to simulate tunnel construction since the early 1980s, but only a few studies involved three-dimensional modelling of mechanized tunneling (e.g., Finno and Clough 1985; Bernat and Cambou 1999; Swoboda and Abu-Krisha 1999; Dias et.al. 2000; Melis et.al. 2002; Kasper and Meschke 2004; Möller 2006). In order to get a better understanding of the effect of the construction process and soil properties on the development of the ground deformations more comprehensive models of tunnel excavation and tunnel support are required in order to capture the 3D nature of mechanized tunneling and the effect of construction parameters such as advance rate, face and grout pressure."

Jan 1, 2016

By A. Martin

Detailed porewater profiles of arsenic and other interstitial metabolites were used to assess the relationship between trophic status, sediment redox chemistry and arsenic mobility in a historic tailings repository. The results demonstrate that in eutrophied systems which exhibit greater sediment oxygen demand, the depth of the Fe(III) redoxcline, and hence depth of arsenic release, may lie in close proximity to the sediment-water interface. As a result, arsenic scavenging mechanisms are significantly reduced, resulting in a greater flux of arsenic to the water column. Such considerations have important implications for the management of pit lakes, tailings ponds and contaminated lakes which may consider: 1) the discharge of sewage to the water body during operations; and/or 2) post-closure fertilization as a remediation strategy.

Jan 1, 2002

By M. Stoica

Bioremediation is a complex process which involves mass transfer, chemical and biochemical phenomena. In particular, the adsorption kinetics of a substance by biomass may by model by taking into account: - Enzymatic kinetics type; - Combined kinetics - enzymatic kinetics at the same time with the Monod type biomass growth; - Chemical kinetics for substance adsorption according to Freundlich and Langmuir ad-sorption isotherms; - New empirical kinetics models based on experimental data. In this paper modelling of kinetics of bivalent lead ions on live vegetal biomass (aquatic plant Pistia stratiotes) as well as of hydrocarbons on dead vegetal biomass (pyrolysed nuts) is studied (Stoica, 2004). Modelling was carried out using experimental data and relative equations with an error of 5%.

Jan 1, 2006

By Gary Jobson

The Mt Todd Gold Mine is owned and operated by Zapopan NL, and is located 300km south of Darwin near the town of Katherine. The crushing plant and heap leach facility, which has operated since November 1993, has recently been expanded to treat 6 Mtpa with 1995 budget gold production reaching 120,000 oz from a head grade of 1.12 git. The process flowsheet and equipment are described, with innovative key features including:

Jan 1, 1995

By G. C. Anderson

The Cleveland Cliffs NOLA electronics and software upgrade is a Windows based system that simultaneously controls two Texas Nuclear NOLAs and associated sampling. It uses new spectrum analysis and algorithms to produce accurate, linear silica measurement with slurries that range from 5 through 50 percent solids. This linearity allows us to achieve a reproducible procedural calibration. The hardware consists of readily available shelf items, is extremely redundant and eliminates all NIM bus modules.

Jan 1, 2003

By S. K. Vidyarthi

Most wastewater clean-up processes suffer from a fundamental lack of specificity in that a Reverse Osmosis process removes all dissolved solids, an Electrodialysis Reversal process removes all ions, wanted or unwanted, etc. Most techniques require the use of a membrane or contact surfaces that are prone to foul-up and are ineffective in situations where solids may be present. A photochemical process for the metallurgical industry on the other hand has the ability to operate specifically on targets that can range from one selected ion to an entire group of homologous species such as all biologically active species. Processes can be designed to change the oxidation states of a target altering the environmental impact. Several processes are currently in operation ranging from Cyanide removal to disposal of radiation wastes. This paper describes applicable photochemical processes with the help of certain key model examples.

Jan 1, 1988

By S. J. Porter, M. T. McRae

The new tunnel at Genting Sempah is part of a privately funded infrastructure projectthat involves duplicating the existing highway extending from the Gombok Toll Plaza near Kuala Lumpur to Karak, in Malaysia. The 60 km long tollway includes an 800 m long, two-lane highway tunnel with excavated dimensions of 10.5 m wide by 8 m high. The majority of the tunnel extends through slightly to moderately weathered, moderately to highly jointed quartz porphyry. Excavation of the tunnel was performed using drill and blast methods and the primary tunnel support consists of rock dowels and shotcrete except for short sections adjacent to the portals where steel sets were utilized. A portion of the tunnel encountered sheared and altered material that was successfully supported using rock dowels and shotcrete. The final lining for the tunnel consists of mesh and fiber reinforced shotcrete. The flexible nature of the primary support and shotcrete final lining resulted in considerable cost savings and expedient construction methods.

Jan 1, 1997

The choice between EPB - and Slurry Shields is influenced by the following factors: grain size distribution, cohesiveness, occurence of boulders, occurence of gas, feasibility of soil separation and muck disposal, and settlement properties of the soil. The simple equation cohesive soils = EPB Shields and non cohesive soils = Slurry Shield is very often superimposed by other facts. For example, the occurence of a large amount of boulders in weak cohesive soils, where the application of roller discs is not recommendable, may lead to the use of a Slurry Shield with a rock crusher, thus accepting the disadvantage of a sophisticated separation plant; whereas the occurence of contaminated groundwater or gas may exclude the use of a Slurry Shield. In the following examples the choice of a Slurry Shield or EPBS will be explained and justified with regard of the above factors.

Jan 1, 1995

By G. M. Smith

Several significant past and present producers of high grade and bulk tonnage gold ore from southeastern California and southwestern Arizona can be empirically and genetically linked to regional peraluminous magmatism which occurred during the late Cretaceous and early Tertiary. Geological relationships and geochemical characteristics from the Fortuna Mine area will be described and compared to those of the Tumco Mines area. Each of these historical gold producers is viewed as a morphologic end member in otherwise genetically linked metallogeny. Cold-quartz veins at Fortuna can be directly linked to peraluminous pegmatites both physically and mineralogically. Silica-magnetite±spidote±garnet rock which occurs as relatively barren, discontinuous, foliation- parallel horizons at Fortuna, but as high grade gold ore at Tumco, is interpreted as replacement of calcareous units during the same episode of peraluminous magnatism responsible for the gold vein mineralization. Whole rock and trace element data from pagmatites and aplites of the Fortuna and Tumco areas, together with data from the Gunnery Range batholith of southwestern Arizona, indicate that the magma series (after Keith, 1984) responsible for the gold metallogeny is peraluminous calcic, and is quite rich in sodium.

Jan 1, 1987

By E. L. Fidler, T. E. Finch

Wayne Anderson Regarding the technical paper by Thomas E. Finch and Edward L. Fidler, "Recovery of Stray (Thin) Seams in Western Coal Mining." I would like to comment on this subject. In western Canada, most strip mines encounter thin seam coal or rider seams. Although the paper addresses the problems and costs associated with the recovery of this coal, it does not take into account what the savings are. Without looking at the savings, the "Total Objective" is of course not clear. I feel that in a stripping operation the mine can spend per ton (of the thin seam) up to their dragline stripping costs per ton to recover a rider seam or thin seam. The reasoning behind this is simply that this is the price the mine will have to pay to expose an equivalent amount of coal without the recovery of these thin seams. If the mine can recover a rider seam or thin seam for less than the dragline operating costs per ton, a savings will be realized. By recovering a thin seam or rider seam, the life of an ore body is extended by that amount of coal not thrown away. In addition, the cost of land acquisition, associated permits, capital, and reclamation will be reduced as more coal is delivered for a given area. When the above points are considered, the recovery of these thin seams can be very profitable and indeed worth recovering.

Jan 11, 1982

By Kenneth J. Leib, Laurie Wirt, M. Alisa Mast

Chemical-constituent loads were determined for an alpine stream in southwestern Colorado that is affected by natural acid drainage from weathering of hydrothermally-altered rock and from acidic metal-rich discharge from abandoned mines. Base-flow loads were compared to storm-related loads using a tracer-dilution approach. A rainstom occurred during the tracer injection, providing the opportunity to measure metal loads before, during, and after storm runoff. Chemical-constituent loads during the storm increased by 1 to 2 orders of magnitude relative to base-flow conditions. The increase in loads was related to two distinct periods; (1) a flush of higher concentrations that occurred soon after rainfall began, and (2) the peak of storm runoff. The initial flush-having no measurable change in discharge--contained the highest loads of trace metals and dissolved iron. The chemical character of peak runoff was distinctly different, as evidenced by the highest loads of total and dissolved major elements and total iron.

Jan 1, 2000

By Stanley C. Suboleski, C. B. Manula

INTRODUCTION In any mining operation all possible steps should be taken to increase efficiency. One area for improvement is mine planning and design, particularly in the area of equipment selection for room-and-pillar systems. Be- cause of the availability of a wide variety of face machines, a fair degree of selectivity can be exercised in the choice of equipment for a particular job. However, this choice must be made on the basis of quantitative facts and forecasts related to the mining application. The purpose of this section is to develop and analyze the details of the mining process. Some specific areas studied include the relationship of system design to productivity, suboptimization as a result of equipment changes, and measurement of system performance. The plan of work leading to a quantitative description of these study areas is based on the growing interest in total system design using simulation as an analytical method (Manula, 1963). CHARACTERISTICS OF PRODUCTION OPERATIONS FROM ROOM-AND-PILLAR SECTIONS For a given mining method, raw production in a given section of a mine is primarily dependent upon the coal seam thickness, roof and floor conditions, methane emission, the mining methods, and the man-machine element. Average section production varies from 300 to 800 st per shift for conventional and continuous mining in high seams and from less than 100 to 300 st per shift in low seams. Since the reject varies from 0 to 40%, these figures must be decreased by the appropriate percentage to reflect the amount of clean coal mined. Personnel requirements per production section per shift for the various methods are listed in Table 1. Table 1. Production Personnel Method No. Method No. Conventional 12-1 5 Longwall 9-14 Continuous 9-1 2 Shortwall 9-12 MINING VARIABLES To evaluate the constraints and interrelationships for various mining methods, it is necessary to categorize the variables which underlie system production potential. Seven critical independent variables which determine production can be identified and categorized (Suboleski, 1978) : Seam Height The five categories are as follows: less than 36 in.;. 36 to 55 in.; 55 to 100 in.; 100 to 180 in.; and greater than 180 in. Floor Quality Floor quality ranges from : Excellent: Smooth, hard, grades less than 1 to 1 % % , and dry. Good: Smooth, soft but dry, with grades less than 3 % . The floor will deteriorate, but cautious operation can prevent it. There may possibly be heaving at some later time. Fair. Soft and damp. There is occasional interference with equipment operation; requires the use of four-wheel drive shuttle cars; ruts with regular use, and may have adverse grades of 5 to 7%. This may be coupled with slippery bottom and/or occasional steep rolls. Poor: Soft and wet. Requires blocking of the bottom to support equipment. There are frequent steep rolls and grades in excess of 7%. Roof Quality Roof quality ranges from : Excellent: Men are able to work under the unsupported top during the initial production cycle if legally permitted. Good: The roof is bolted on a 4 x 4 or 5 x 5 pattern with short bolts (442 in.) or <seam height if the seam >42 in., or requires posting with no bolts on a 4 x 4 or 5 x 5 pattern. There are no falls. Average: The roof is normally bolted on a 4 x 4 or 5 x 5 pattern, but with long bolts (>seam height or >6 ft.). There are infrequent minor falls or there may be an excellent roof which is difficult to drill. Fair: This type often requires spot bolting in addition to the regular pattern or bolting with planks. The roof conditions require shorter than planned cuts, or narrow cuts. Poor: This type requires bolts plus crossbars and posts, or installation of yielding supports or truss-type support. It is almost certain to fall if this is not done. Methane Liberation This ranges from none detected to low (no buildup at the face, even with minimum ventilation requirements) to moderate (the curtains must be extremely tight and tubing close to the face or methane will build up to 1 % during the loading of the car) to high (methane will build up to 170 if the miner is operated at the normal rate, even with proper ventilation). Hardness of Coal Coal hardness falls into the following categories: Soft: Soft coal is easily cut by a continuous miner. A plow could be used by longwall. Average: Coal of average hardness could be easily cut by a miner, and a shearer would be used in the longwall. Moderate: Moderately hard coal causes difficult cut-

Jan 1, 1982

By R. V. Hunter, J. F. T. Agapito

Introduction Significant increases in extraction ratio on the order of 6% to 8%, equivalent to as much as 142 t/m (48 st per ft) of panel, have occurred at the Big Island trona mine during the last five years with the help of a practical rock mechanics program. This increase in resource recovery also has contributed to improvements in productivity. Both conventional and continuous machine mining have been used to mine two flat-lying trona beds at depths of 250 m and 260 m (820 ft and 853 ft) in the Green River Formation in southwestern Wyoming. Conventional room-and-pillarmining originally was conducted in panels with extractions of 5 8% to 60%. The use of yield pillars has allowed the panel extraction in increase to 66%. Continuous machine mining was introduced, with a 64% extraction ratio using long, narrow pillars and wide rooms. Further improvements in resource recovery seem feasible in light of present mining experience. The rock mechanics program consisted of field instrumentation to determine the pillar and roof response hole locations. to mining and computer modeling to evaluate the stability of various layouts, which were then adopted for mining. Mining background Stauffer Chemical Co.&apos;s Big Island mine and refinery are located 40 km (25 miles) northwest of Green River, WY. Underground mining operations supply trona, a sodium mineral, to the refinery to produce soda ash. The room-and-pillar method is used to mine two 3 to 3.6 m (10 to 12 ft) thick, flat-laying seams at depths of about 250 to 260 m (820 to 850 ft). Mine production in 1986 was 2.3 Mt (2.5 million st). These were supplied through both conventional and continuous machine mining sec-

Jan 1, 1989

By C. John Dunnicliff, Birger Schmidt

INTRODUCTION To be effective and useful, monitoring of tunnel construction must be carefully planned throughout all steps. A vital and frequently overlooked step is a clear definition of the specific purposes of the instrumentation. Most tunnel construction monitoring has in the past been of benefit to research, the advancement of tunneling practice, wittingly or not. The development of monitoring instrumentation for the benefit of the project from which the data are recovered has very significant potential for risk and cost reduction of soft ground tunneling. A systematic approach to tunnel construction monitoring, from conception to full implementation, includes at least the following nine tasks or steps: Definition of benefits and purposes; design and project specification to draw full benefits; selection of monitoring parameters; selection of instruments and writing of specifications for procurement and installation; procurement and installation; reading and maintenance; data storage and retrieval; interpretation; implementation. Some of these steps are fairly easy and resolved through the use of established theories and technologies. The difficult ones are those that require the bending of minds, those that involve changes in the ways engineers design soft ground tunnels, the way owners pay for tunnels, and the construction is managed, inspected and controlled. Performance monitoring can be of benefit to the owner, design

Jan 1, 1974