Search Documents

By David K. Parrish, Duane A. Labreche

Analyses of jointed, cracked, and fractured rock masses are needed in a variety of applications, including estimates of reduced elastic modulus for damaged rock, estimates of permeability changes as a function of stress changes, and estimates of relaxed regions due to excavation. A numerical model of a jointed rock mass, the compliant joint model, was used to study the response of a jointed rock mass near a circular excavation. The joint constitutive model was linear elastic in shear and nonlinear elastic in the relationship between normal stress and joint closure. Initial stresses were geostatic and representative of stresses in a granitic jointed rock mass approximately 300 m deep. The joint properties were based on values that are representative of joints in granite. The results from numerical simulations were compared with analytical results for stress near a circular opening in an elastic medium having reduced Young's Moduli to simulate jointing effects on the rock mass. The differences in response between the two models resulted from the differences in the symmetry of elastic properties, the shear modulus of the continua, and the constitutive relations in the two models. For example, the non- linear anisotropic elastic continuum described by the compliant joint model resulted in vertical stress concentrations near the side of the circular opening that were 25 percent higher than the vertical stress concentrations in an isotropic linear elastic medium. The equivalent Young's Moduli in the vertical and horizontal directions of the compliant joint continuum deviated by as much as 50 percent from the values assigned to the modeled region prior to excavations. The perturbations of the elastic Young's Moduli extended to distances of two to three radii from the opening.

Jan 1, 1986

By S. K. Kawatra

Various types of mathematical descriptions of the flotation process are used in the design of a full scale flotation circuit. Mechanistic descriptions developed under controlled laboratory conditions establish theoretical residence time requirements. Empirical models, describing flotation performance as a function of full scale operating variables, are established from one flotation system and applied to another hypothetical system. Problems of design by mechanistic modeling, such as scale up factors, can be alleviated if the model is developed from a full scale flotation circuit. However, the numerous uncontrollable variables encountered in a full scale operation would preclude the practical application of such a model. Incorporating empirical relations into the full scale mechanistic model will facilitate its effective use as a guide for flotation circuit design. A semi-empirical model has been developed that promises to offer a more effective means of flotation circuit design.

Jan 1, 1982

By Adam Shang Robert Fu

The Yung-Chung-Tunnel in Taiwan, constructed for the Taiwan-East Railway Bureau, collapsed during construction when a water bearing, fractured marble zone was intersected. The inflow was approximately 4,000 liters/second. In spite of 30 relief holes the total inflow into the tunnel remained constant. The pre-excavation grouting through the re-aligned tunnel had to be conducted under extreme flow-conditions. A hot bitumen grouting program was selected for technical and economical reasons out of 13 international proposals. The technical challenges were: grouting under severe flow conditions high formation water pressures to be injected with hot bitumen at high temperatures and pressures The hot bitumen grouting program resulted in a dramatic reduction in the hydraulic conductivity and stabilization of the formation and facilitated a problem-free excavation.

Jan 1, 2007

By R. E. Johnson, L. V. Araújo, B. R. Palmer, L. M. Abrantes, G. W. Warren

The behaviour of chalcopyrite - mineral specimens and a Portuguese concentrate - in 2M chloride solutions prepared from hydrochloric acid and sodium chloride, has been characterized by cyclic voltammetry. The study has shown the influence of the potential and of the presence of impurities in the reaction schemes and their relative extent. The dissolution of chalcopyrite concentrate under potentiostatic control has been investigated and found to confirm the effect of the selected potential on the surface modification/rate of dissolution. An attempt has been made to correlate the information obtained with the response of the concentrate electrode to constant current treatments.

Jan 1, 1993

By P. Riveros, A. Pratt, G. Deschênes

The effect of pyrite, pyrrhotite, chalcopyrite, realgar and arsenopyrite on gold dissolution in cyanide media was investigated. The cyanidation of synthetic gold ores, in the presence of various concentrations of sulphides, was studied under constant experimental conditions. A mineralogical analysis of the minerals was performed. The leaching kinetics were determined. The negative effect of sulphides on the gold dissolution rate varies with the sulphide mineral, and decreases according to the following order: realgar > pyrrhotite > chalcopyrite > pyrite > arsenopyrite. The chemical characterization of gold and sulphide minerals surfaces using X-ray photoelectron spectroscopy (XPS) was undertaken to identify the mechanisms involved. XPS analysis showed that a passivation layer of sulphides, arsenic or iron compounds may form on the gold surface as a result of the dissolution of the sulphide minerals.

Jan 1, 2002

By M. Sears, G. S. Esterhuizen, Z. Khademian

According to the 2010-2019 Mine Safety and Health Administration (MSHA) accident report database, 91% of reported ground control accidents in U.S. longwall mines were caused by roof instability. Gateroads are subject to significant changes in loading conditions from the development to the longwall abutment loading phases. When combined with thinly bedded shale roof, found in many U.S. longwall coal mines, the design of efficient roof support becomes challenging. In previous work, the Bonded Block Method (BBM) modeling of roof by UDEC was validated against field extensometer measurements in a longwall gateroad entry roof at a 180-m depth of cover. The BBM was shown as capable of capturing delamination and buckling of shale roof, one of the main roof instability mechanisms in longwall mines. This paper presents the recent findings on the roof-support interaction using BBM models of the same longwall entry. The effects of cable bolts, roof bolt density, and strap support on potential roof instability are studied. These types of studies are difficult and costly to conduct in an operating mine. Results show how the contribution of bolts, straps, and cable bolts can be quantified using the BBM models. The study demonstrates the potential for BBM numerical models to help understand the complex roof and support system interactions and to assist with optimizing gateroad support systems.

Feb 1, 2023

By Zoheir Khademian, Morgan Sears

According to the 2010–2019 Mine Safety and Health Administration (MSHA) accident report database, 91% of reported ground control accidents in US longwall mines were caused by roof instability. Gateroads are subjected to significant changes in loading conditions from the development to the longwall abutment loading phases. When combined with thinly bedded shale roof, found in many US longwall coal mines, the design of efficient roof support becomes challenging. In previous work, the bonded block modeling (BBM) of roof by UDEC was validated against field extensometer measurements in a longwall entry roof at a 180-m depth of cover. The BBM was shown capable of capturing delamination and buckling of shale roof, one of the main roof instability mechanisms in longwall mines. This paper presents the recent findings on the roof-support interaction using BBM models of the same longwall entry. The effects of cable bolts, roof bolt density, and strap support on potential roof instability are studied. Results demonstrate the potential for BBM numerical models to help understand the complex roof and support system interactions and to assist with optimizing gateroad support systems.

Feb 13, 2024

By Myles P. Reilly, Randall A. Snowdon, John Temporal, O&apos

The paper describes studies made at the Transport and Road Research Laboratory, UK, of the mechanical cutting characteristics using disc cutters, of rocks with compressive strengths up to 340 MPa. These studies have been performed in both the single pass mode, where interactive breakout occurs between adjacent grooves on every pass of the tool, and the multiple pass mode, where several passes may be required to cause breakout. In addition, experiments to determine the effect on cutting performance of the hydraulic stiffness of tunnelling machines are described. The results of these tests are analysed and discussed in the context of the design of full-face tunnelling machines.

Jan 1, 1983

By Y. C. Kim, I. S. Roditis, P. K. Medhi

The strongly skewed grade distributions and the need to estimate the local recoverable reserves in a selective mining environment are the two problems that ordinary kriging (OK) cannot easily handle. With the recent introduction of the non- parametric, distribution-free technique of indicator kriging (IK), the above problems can be solved. This paper describes the result of performance evaluation of IK in an open-pit gold-silver deposit. For performance evaluation, the predictions of local recoverable reserves using IK were compared with the actual reserves based on blasthole information. The IK estimator, although a bit optimistic (or overestimating), performed very well in predicting the total recoverable ounces of gold from each panel on a test bench. The OK estimator was also used to try to predict local recoverable reserves, by treating each panel as either waste or ore, depending on the panel's average grade. Under this criterion, OK was found to be quite biased and pessimistic (or underestimating).

Jan 1, 1988

By M. K. McMullen

Mineral Development Agreements (MDA?s) are a cooperative mechanism in Canada by which the federal and individual provincial governments can coordinate their scientific, techno- logical and market development resources in order to implement measures designed to stimulate mineral exploration and development by the private sector; the objective, ultimately, being to increase the mineral industry?s contribution to provincial economies. In the latest round of MDA?s, which was initiated in 1984, a significant number of planned activities relate to industrial minerals. This paper will describe the nature and importance of MDA's in Canada and will outline the wide range of activities taking place with respect to industrial minerals.

Jan 1, 1987

By J. A. Chermak, D. D. Runnells

Sulfide-bearing waste rock, ore and tailings have the potential for generating acid rock drainage (ARD) when exposed to an oxidizing environment. The possibility exists of utilizing the acid produced to react with lime and/or limestone to form a self-sealing cap on the reactive waste rock and tailings. Laboratory column experiments were conducted using acid-generating waste rock with a surface amendment of limestone and/or lime. Artificial rainwater was introduced and allowed to drain through the columns. Results demonstrated that the limestone and lime reacted with the acidic rock, resulting in the precipitation of a hardpan layer of gypsum and amorphous iron oxyhydroxide at the surface. The hardpan layer significantly reduced the effective permeability of the column. Based on the results of this study, it should be possible to create hardpan layers as chemical caps to significantly reduce the infiltration of rainwater and snowmelt into acidic waste rock or tailings material in the field. Unlike traditional capping methods, e.g., clay and high-density polyethylene (HDPE) covers, chemical caps should be self-healing.

Jan 1, 1998

By Wolfgang Roth

In 1990, a residential area above the North Outfall Sewer (NOS) tunnel constructed in 1924, experienced subsidence. After sewage was diverted into the North Outfall Replacement Sewer (NORS), soil probing from within the tunnel was conducted, soil-improvement options were developed, and a preferred grouting scheme was analyzed by numerical modeling to evaluate the stability of the 80-year+ old tunnel liner under grouting-induced loading conditions. This paper discusses the initial field investigation and the development and analysis of a grouting scheme originally intended to be implemented before relining of the tunnel. The scheme was later modified, and the new liner was installed before the final probing and grouting work was done.

Jan 1, 2008

By Louis W. Cope

The Compañía El Zapote Yacimiento Y Minas, S.A. has an ore body containing 650,000 tons of 0.185 oz/t gold ore in Mexico. Metallurgical testwork has been done to determine the response of this ore to several possible processing schemes. The paper describes the rationale for selecting the Silver State Mining Co. methods in Colorado. Plans for developing the mine and building the treatment plant are described in detail in the paper. Estimates of capital and operating costs are included.

Jan 1, 1984

By D. E. Ranta, George F. Weaton

Estimating the Iron Ore reserves of Minnesota are directly related to both the geology of the deposit and the Scandinavian heritage of its people. The flat lying deposits, when properly prospected, make estimating easy and accurate across wide areas of the Mesabi Range. It also makes taxation simple on the unmined reserves. The reserves are their heritage and all the people should benefit, not just the owners. Heritage also dictates that newly discovered ores were there before discovery, hence, subject to the omitted property tax and liable for six years back taxes.

Jan 1, 1992

By K. N. Han, J. J. Kellar, Y. Guan

The adsorption of zinc species onto silica in ammoniacal solutions was studied. The adsorption isotherms indicated that the adsorption of zinc increased with increasing pH. The adsorption density increased as the zinc equilibrium concentration increased up to =3.5x10-4 M. Above this concentration, the adsorption density was independent of the equilibrium concentration, and a maxima adsorption density was reached. Temperature had no significant effect on the adsorption density.

Jan 1, 1995

By V. Iordachita

In the beginning of the third millennium, the world mining industry has to cope with many challenges; the continuous need for mineral resource deposits and the mostly unsolved economic efforts should be accompanied with ecologic measures mankind has to take in order to avoid self-destruction. The present paper analyses the possibilities of using underground mining spaces in Romania for storing dangerous waste and suggests viable solutions. The characteristics of dangerous wastes and their disposal in suitable underground spaces are analyzed. Also, some methods for deactivating dangerous solid wastes as well as the importance of monitoring underground spaces in order to eliminate environmental impact risks are presented.

Jan 1, 2008

By B. R. Pothini, H. von Schonfeldt

In underground coal mining many excavated openings have a relatively short projected life span. To ensure safety for men and materials at a minimum cost over the projected operating life, only pillars for overburden support and roof bolts for support of the openings are used extensively. Mining activity constantly changes the geometry of the mine producing load changes on the structural support members of the openings that often induce unstable deformations which can lead to roof falls or pillar failures. The paper describes how simple deformation measurements can be used to design primary and supplementary roof supports and to predict roof falls and possibly pillar bumps. Specifically, bed separations in the roof measured directly with the help of borescopes and calculated from differential convergence data are used to optimize bolt links or support requirements for chemical stabilization of mine roofs. Roof falls are predicted on the basis of admissible values for cumulative convergence between roof and floor, convergence rate, and the change of the rate of convergence. The pillar extraction operations convergence anomalies detected from contouring identify bump prone pillars, while convergence and pillar dilation determine the yield zone in a pillar to verify pillar softening and de-stressing. Manuscript not received in time for publication.

Jan 1, 1983

By J. G. Wargo

In situ leaching of disseminate gold deposits has been studied from a theoretical perspective to outline the operating environment for the process. Rock permeability and the relationship of permeability to the site of gold particle deposition are key factors in predicting the efficiency of in situ leaching. Permeability measurements, however, have rarely been made during gold exploration, so that secondary geologic features of the deposit must be used. This paper examines some of the geologic characteristics of disseminated gold deposits and comments on the problems and possibilities of in situ leaching of gold.

Jan 1, 1987

By D. Hong, K. N. Han

The leaching behavior of rhenium in ammonium iodide solutions with iodine as oxidant was studied. Experiments were carried out in an autoclave to investigate the effects of stirring speed, temperature, solution pH, and iodine and iodide concentrations on the dissolution of rhenium. It was found that a high temperature and a high solution pH were essential for the efficient leaching of rhenium. The dissolution rate was found to be dependent upon the concentration of iodine and iodide. It was concluded that the dissolution of rhenium under the conditions studied was controlled by the mass transfer of iodine with an apparent activation energy of 15.8 kJ/mole.

Jan 1, 1999

By A. A. Bilgin

The prevention of acid mine drainage (AMD) in situ is more attractive than down-gradient treatment alternatives that do not involve source control. AMD source control can be achieved by shifting the microbial activity in the sulfidic rock from pyrite oxidation to anaerobic heterotrophic activity. This is achieved by adding biodegradable organic carbon amendments to the sulfidic rock. This technique was applied to an abandoned coal mine pool in Pennsylvania. The pool had a pH of 3.0 to 3.5. Following treatment, near-neutral pH and decreased effluent heavy metal concentrations were achieved. In situ bioremediation by the enhancement of bacterial iron and sulfate reduction is a promising technology for AMD prevention.

Jan 1, 2007