Search Documents

By J. Noll, D. Yantek, J. Organiscak

The Office of Mine Safety and Health Research of the U.S. National Institute for Occupational Safety and Health (NIOSH OMSHR) conducted laboratory testing of a self-tramming, remotely controlled mobile Dry Scrubber (DS) that J.H. Fletcher and Co. developed under a contract with NIOSH OMSHR to reduce the exposure of miners to airborne dust. The scrubber was found to average greater than 95 percent dust removal efficiency with disposable filters, and 88 and 90 percent, respectively, with optional washable filters in their prewash and post-wash test conditions. Although the washable filters can be reused, washing them generated personal and downstream respirable dust concentrations of 1.2 and 8.3 mg/m3, respectively, for a 10-min washing period. The scrubber’s velocity-pressure-regulated variablefrequency- drive fan maintained relatively consistent airflow near the targeted 1.42 and 4.25 m3/s (3,000 and 9,000 ft3/min) airflow rates during most of the laboratory dust testing until reaching its maximum 60-Hz fan motor frequency or horsepower rating at 2,610 Pa (10.5 in. w.g.) of filter differential pressure and 3.97 m3/s (8,420 ft3/min) of scrubber airflow quantity. Laboratory sound level measurements of the scrubber showed that the outlet side of the scrubber was noisier, and the loaded filters increased sound levels compared with clean filters at the same airflow quantities. With loaded filters, the scrubber reached a 90 dB(A) sound level at 2.83 m3/s (6,000 ft3/min) of scrubber airflow, indicating that miners should not be overexposed in relation to MSHA’s permissible exposure level — under Title 30 Code of Federal Regulations Part 62.101— of 90 dB(A) at or below this airflow quantity. The scrubber’s washable filters were not used during field-testing because of their lower respirable dust removal efficiency and the airborne dust generated by filter washing. Field-testing the scrubber with disposable filters at two underground coal mine sections showed that it could clean a portion of the section return air and provide dust reduction of about 50 percent at the face area downstream of the continuous-miner operation.

Jan 1, 2016

By Brian Fulcher

The Arrowhead Tunnels Project represents the final portion of a 70 km (44-mile) long water conveyance facility that will bring up to 28 m3/sec (1,000 ft 3/sec) of water into Southern California. The 13 km (8-mile) tunnelling project is well underway and consists of two, 5.8 m (19-ft) diameter TBM bores through extremely variable geological conditions. An extensive and essential pre-excavation drilling and grouting program was performed in all reaches of the Arrowhead Tunnels Project, located north of San Bernardino, CA. This program supported the advance of two hybrid hard rock TBMs though extremely challenging ground conditions under substantial ground cover and up to 27 bar (900 ft) of ground water pressure. The well known San Andreas Fault lies nearby and has greatly influenced the local geological conditions. This paper will describe the means, methods and materials used throughout the numerous phases of the pre-excavation grouting program. It will also describe many versatile, flexible and innovative drilling and grouting methods and equipment systems utilized to improve performance, save time and costs in constantly changing geological conditions. Considerable lessons learned have been learned while overcoming some extremely formidable ground conditions and safely advancing the tunnels.

Jan 1, 2008

By D. D. Gertenbach

"The successful commercialization of a pressure oxidation (POX) process for recovering metal values, including gold, copper, zinc, nickel and molybdenum, is the result of a carefully planned development program. The initial task involves developing one or more conceptual flowsheets, including the POX autoclave and downstream purification and recovery steps. A laboratory program is completed to determine the technical viability of the flowsheets, define the operating parameters for each step and provide information for an initial economic assessment of the process. The process is then confirmed during a continuous pilot plant program, providing engineering design data and other information for the commercial design. A well-thought-out development program has been shown to be critical for reducing the risk of commercializing POX processes. Experiences developing POX processes for refractory gold ores and copper concentrates are briefly discussed. IntroductionPressure oxidation (POX) has become a common commercial operation for processing sulfide-bearing feedstocks. These feedstocks include gold ores and concentrates; copper concentrates; nickel concentrates and mattes; zinc concentrates; and molybdenum concentrates. Drivers for the development and commercialization of POX processes include:• The high cost for pyrometallurgical processing of sulfide ores, much of which is attributed to environmental controls.• The motivation to implement safe and more environmentally attractive alternatives for sulfide ores.• The need to process increasingly difficult ores with complex mineralogy.• Improvements made over the last 25 years in POX equipment design and experience operating commercial POX plants.Although the capital and operating costs for commercial POX processing can be high, this technology is capable of rapid oxidation of most sulfides and arsenic minerals in the feed, with little noxious gases and environmentally stable iron arsenate and other iron compounds in the POX residue (Marsden and House, 2006).In POX operations, sulfides are oxidized to either sulfates or elemental sulfur in an autoclave at elevated temperature and pressure with oxygen gas. An example is the overall oxidation reactions of chalcopyrite when sufficient oxygen is present, shown in the following reactions:"

Jan 1, 2016

By V. O. Tenorio, K. P. Hague

Mines are constantly trying to improve production processes by optimizing work cycles, reducing operational delays, minimizing costs, controlling equipment utilization, and preventing occupational hazards. Currently, advances in digital mining technologies within the concepts of 5G and Industrial Touch Internet are allowing better control and monitoring of underground mining equipment, with centralized control systems that unify data analysis for proper decision making. A wireless 5G-based platform for controlling and monitoring systems for underground mine operations can be designed over a comprehensive layout in where bandwidth selection, sensor location, Wi-Fi repeaters and power distribution are put together to build a successful supervisory system. In order to confirm the validation of these concepts, a case study is proposed for a medium-sized underground mine with a multi-level network which includes tablets managed by production supervisors, along with other data collection devices installed in semi-autonomous mining equipment, collecting, and distributing data in near-real time, with interconnection to support and services areas on the surface.

Mar 2, 2022

By M. E. Buzon, M. E. Gunter, B. D. McNamee

A Google search on talc asbestos yields more than 500,000 hits due to the growing number of civil lawsuits in this area. Historically, the litigation was centered on amphibole-containing industrial talc. There was no debate these talcs contained amphiboles, but the issue was the definition of asbestos and whether the amphiboles had an asbestiform habit. Ultramafic-hosted talcs, however, are formed in such a way as to not favor the formation of amphiboles in the talc, but they can occur in the surrounding black-wall. In these deposits, the serpentinite host rock is in direct contact with the talc, therefore, allegations can be made that non-asbestiform amphiboles or non-regulated serpentine group minerals can occur in the final products. We analyzed talcs from both metamorphosed carbonate- and ultramafic-hosted talc deposits using polarized light microscopy (PLM), scanning electron microscopy (SEM) with energy-dispersive spectroscopy (EDS), electron microprobe (EPMA) with wavelengthdispersive spectroscopy (WDS), transmission electron microscopy (TEM) with EDS, and powder X-ray diffraction (XRD). Compositions of minerals determined by EDS alone are not sufficient to confidently identify asbestos, despite common practices by some researchers. We emphasize, using both historical samples, and analyses of currently contested minerals, the importance of determining both the structure and composition of a mineral, as well as defining its morphology, before concluding whether it is asbestos.

Jan 1, 2018

By Jr. Raleigh

Three run-of-mine bituminous coals, which ranged in rank from low volatile to high volatile A, were floated at nominal -28 mesh (590 µ m), -100 mesh (150 µ m), and -400 mesh (37 µ m) feed particle sizes with selected pyrite depressants and a dispersant. For the coals tested, pyrite and ash-forming minerals were usually rejected best at a -100 mesh feed particle size. Depressant additions tended to improve flotation selectivity between pyrite and coal. When joint dispersant-depressant systems were used at -100 mesh (150 µ m) feed particle sizes, the total sulfur content of the clean coal decreased further. For a comparable coal yield, less fuel oil collector was required for the flotation of -100 mesh coal than was required for the flotation of either -28 or -400 mesh feed.

Jan 1, 1990

By Jared Winkler, Jon A. Hummer, Aleksandar D. Bugarski, Shad Peters, Steven E. Mischler, Steve Cochrane, Shawn Vanderslice, Teresa Barone

The case study assessed submicron aerosols at a continuous miner (CM) section, diesel aerosol concentrations at the longwall (LW) section, and elemental carbon (EC) and total carbon (TC) exposures. Aerosols at CM sections were a mix of freshly generated and those from main drifts. Low ambient concentrations and personal exposures suggest effective control strategies, with further reductions possible by curbing emissions from high-emitting light-duty vehicles.

Mar 16, 2022

By A. N. Pritchard

The development of vibrating screens over the last century has seen many variations to suit the exacting requirements of industry. Indeed, as each year passes, industry has presented the challenge to screen manufacturers of supplying larger machines than those used in the past and the question is often posed - what is the maximum limit? Not only must size or screen area be considered but excellence of performance in terms of screening efficiency must be maintained or maximized.

Jan 1, 1983

By A. S. Speirs

Over the last few years, the never-ending search for mineral wealth has taken the exploration efforts of Canadian mining companies further and further into the High Arctic and isolated locations where regularly scheduled transportation and communication facilities are nonexistent. Names such as Black Angel, Nanisivik, Asbestos Hill, New Quebec Raglan, Rabbit Lake, and Arvik are today frequently mentioned in mining publications. Twenty years ago, mining in these locations was unheard of, mainly due to logistic problems. However, improvements in the design and use of helicopters, STOL aircraft, and icebreakers in northern areas have helped to overcome these problems, making these locations more attractive to mining companies. Since 1969, when Redpath completed its first Arctic project at Texas Gulf's Scrathcona Sound property on the northern tip of Baffin Island, Redpath has been actively involved in contracting and engineering projects in three general areas: the High Arctic, Ungava and Greenland. A map showing some of these projects is shown in Figure 1. In these areas, permafrost conditions exist from a depth of 274 metres in Ungava to a depth of approximately 610 metres in the Little Cornwallis Island area, with rock temperatures ranging from -5°C to -13°C. Outside temperatures range from a low of -50°C in the winter to a high of 21°C in the summer. High winds in the winter result in wind chill factors lower than -73°C

Jan 1, 1980

By A. D. Kalogeropoulos, T. N. Michalakopoulos

This paper deals with the numerical simulation of rock cutting laboratory tests using the discrete element method. The main objective is to provide a method for calibrating numerical DEM models of rock cutting in a systematic way so that realistic results are yielded. The numerical models are developed with the discrete element code Yade, which models rocks as a collection of bonded spheres. The models are calibrated in a four-step process based on the design of experiments method and optimization. The calibrated models are evaluated both quantitatively and qualitatively against actual laboratory cutting tests, in terms of the ratio of the simulated mean cutting force to the actual one and the cutting force time series, respectively. The fully calibrated models showed that the simulated cutting process matched qualitatively the actual cutting force recordings and underestimated the mean cutting force by approximately 3%. It is concluded that well-calibrated numerical simulations of the rock cutting process can provide not only a better understanding of the process itself but also quantitative data regarding the cutting force and energy requirements.

Dec 28, 2022

By Hiroyuki Abé

This paper is a review of research and development on geothermal energy extraction in Japan especially on hydraulic fracturing. First recent geothermal developments in Japan are outlined in Part I. An increase in the production rate of geothermal wells may be highly dependent on the geothermal well stimulation technology based on hydraulic fracturing. The hydraulic fracturing technique must be developed also for geothermal energy to be extracted from hot, dry rock masses. In Part II, the research on hydraulic fracturing and field application are reviewed.

Jan 1, 1982

By Kyle Amoroso, Larry Applegate, Aaron K. McCain

The use of frozen soil as ground improvement and temporary ground support for the excavation and construction of cross passages and adits has gained in popularity over the last decade. Frozen soil provides a number of advantages for this application such as being waterproof, structurally stable, and working well with any soil type. One of the greatest advantages is the ability for the system to be adaptable to the project geometry and site limitations. Multiple case histories illustrate that freezing can occur from the ground surface, from within the tunnel, or as a combination.

Jun 13, 2023

By R. E. Mitchell

The environmental impact assessment (EIA) is the accepted method for evaluating proposed mining and other industrial projects to obtain regulatory approval and to help companies plan for responsible development. Another increasingly common evaluation system for proposed projects is the environmental, social and health impact assessment (ESHIA). An ESHIA differs from an EIA for its generally more comprehensive and inclusive approach to evaluating potential impacts, such as on public health, and other features such as an ecosystem services approach to assessing biophysical and community impacts. An ESHIA may also be required by certain lenders for financing major projects. In this paper, EIA standards for the province of Alberta, Canada are discussed and compared to ESHIA. It concludes with several recommendations for consideration.

Jan 1, 2012

By R. E. J. Putman

The, principle purpose of applying control to any process is to improve -its profitability. Even when considering the impact of a plant on its surrounding ecology this is still, true, since the sanctions felt most immediately from violations of the regulations are the economic penalties or fines which result. 'Economic performance can be improved within a plant in several ways. Steps can be taken to cut the cost or quantity of resources (power, water, steam, reagents) consumed per ton of throughput. Alternatively the operation of the plant can be changed so as to increase product yield per ton of throughput. Or the cost of labor and plant overhead per ton of product can be reduced by raising the total 'throughput, assuming-that the increased amount of product can be sold for the same unit price. In designing a program to improve plant performance, all three routes should be borne in mind. To maximize the return on investment over a longer period, it is also desirable to set up a comprehensive plan of improvement, equipment being specified at each step in the implementation so as to ensure that it fits in with later requirements later implementation being either by means of modular additions or by having the necessary interfaces built into the original equipment. It is much cheaper in the long run to buy features which have been factory-installed, than to have to make provision for their later addition in the field. This paper examines some ways of improving plant performance by the application of various process control techniques using both analog and digital con¬trol equipment. A general philosophy of application is suggested and specific examples described.

Jan 1, 1972

By R. Bryce, T. J. Doughty, K. Stoll

Sulfate-impacted mine waters are under regulatory scrutiny to reduce total dissolved solids (TDS). There are several options to reduce TDS. One option is transforming the soluble sulfate into insoluble ettringite. The Water Company LLC (TWC) patented a process for sulfate removal through ettringite formation by reacting directly with metallic aluminum. Freeport-McMoRan (FMI) and TWC have collaborated to design, build and operate a 10-gallon-per-minute (gpm) ettringite pilot plant to establish reagent consumption, plant availability and full-scale design criteria. Using metallic aluminum as the primary aluminum source for ettringite precipitation eliminates the addition of other ions, resulting in significant demineralization. The pilot plant achieved greater than 98% water recovery, greater than 90% reagent efficiencies and maintained reactor sulfate levels below 250ppm. BACKGROUND Ettringite is a hydrated calcium, aluminum, sulfate mineral with the following formula: Sulfate-impacted mine waters are under regulatory scrutiny to reduce total dissolved solids (TDS). There are several options to reduce TDS. One option is transforming the soluble sulfate into insoluble ettringite. The Water Company LLC (TWC) patented a process for sulfate removal through ettringite formation by reacting directly with metallic aluminum. Freeport-McMoRan (FMI) and TWC have collaborated to design, build and operate a 10-gallon-per-minute (gpm) ettringite pilot plant to establish reagent consumption, plant availability and full-scale design criteria. Using metallic aluminum as the primary aluminum source for ettringite precipitation eliminates the addition of other ions, resulting in significant demineralization. The pilot plant achieved greater than 98% water recovery, greater than 90% reagent efficiencies and maintained reactor sulfate levels below 250ppm. BACKGROUND Ettringite is a hydrated calcium, aluminum, sulfate mineral with the following formula: Ca6Al2(SO4)3(OH)12•26H2O Ettringite readily precipitates in high pH water and by doing so, removes sulfate from impacted waters. The SAVMIN process, piloted in South Africa, is one method to produce ettringite. In this process, aluminum hydroxide is the aluminum source. The Cost Effective Sulfate Removal (CESR) process is similar to SAVMIN, but uses a proprietary aluminum source instead of aluminum hydroxide. Outotec and Veolia also have their own versions of the process using their specialized process equipment. TWC patented a version of ettringite precipitation using metallic aluminum as the aluminum source for ettringite formation. The benefit of using aluminum metal is that no additional ions are added to the process. At high pH, the raw aluminum corrodes in water causing hydrogen gas generation as the water is chemically reduced. This reaction is shown below:

Jan 1, 2019

By Jr. Wallace

This paper describes an analysis performed to determine the cool-down time of drifts in the prospective commercial nuclear waste repository in volcanic tuff at Yucca mountain, Nevada. Two emplacement methods are currently being considered at Yucca mountain. The reference configuration stores the high-level waste in short vertical boreholes, and the alternative configuration stores the waste in long horizontal bore-holes. After emplacement operations for each emplacement drift are complete, the drift will be closed off from continuous ventilation. Given time, the radioactive decay of high-level waste will increase the rock temperature around access and emplacement drifts. Air cooling may be required to re-enter these drifts. The paper discusses the analysis procedure and computer programs used to evaluate the time to cool a drift to acceptable environmental conditions 50 years after emplacement of high-level waste. Key assumptions to the analysis are presented. The results of the study show that cooling either vertical or horizontal configuration emplacement drifts is possible in a reason-able period of time.

Jan 1, 1988

By Richard Stahura

The longtime rule-of-thumb for conveyors was that only one cleaner was needed to solve carryback problems and help keep belt replacement costs under control. That is now being rethought. Belt-cleaning systems manufacturers, designers, and users are shifting to the view that multiple cleaners, placed at key locations on the conveyor and properly maintained, are necessary to solve today's material build-up (carryback) problems. There are still not many statistics on conveyor belt cleaning. But some recent studies support this belief. One study contends that the plant maintenance engineer's biggest problem is keeping the conveyor system running efficiently. The study also said the conveyor itself is responsible for most plant shutdowns. An unscheduled conveyor shutdown can cost more than $100,000/hr and run into millions in lost production in a given year. Other studies pointed out that belt replacement is the greatest single cost of the conveyor system. These studies allude to an important fact: cleaner belts lead to reliability and longer belt life. They showed that a critical relationship exists between characteristics of material being moved and the design of all major conveyor components. In practically all situations this relationship is keyed to belt cleaners, which have long been considered "add-ons" or "accessories." At the Fifth International Coal Utilization Exhibition and Conference, the Sammis Station-Ohio Edison Co. said it installed four belt cleaners on each problem belt. The company found that under certain conditions, when the coal is wet and sticky, carryback can be so heavy that it will flow over two cleaners. Before installing the cleaners, it was necessary to schedule a cleanup crew of four men each day and rent a large vacuum truck for an eight-hour shift. In addition, the company dredged the harbor three times a year, to remove coal spillage. Once the cleaners became operational, however, cleanup costs were reduced to a few days labor every third month. Renting the vacuum truck crew was also eliminated, and harbor dredging became necessary only once each year. In addition, the Mechanical Handling Engineers' Association (MHEA) in London pointed out that standards for cleaners are sorely lacking in the industry. MHEA called for instituting such standards in the future. They also reaffirm using multiple belt cleaners for increased efficiency. MHEA pointed out that some conveyor belts can be cleaned by one device, provided that it is correctly installed and adequately maintained. But MHEA recommended that a system approach be adopted, since this has proved more effective in practice. There are two main reasons why one belt cleaner fails to solve most carryback problems. First, management often reasons that the design of the current cleaner has probably been around for years, so it "must be good." This logic leads to a continued investment in keeping the current model operating, which includes pouring substantial sums of money in "housekeeping" manpower hours because the cleaner does not clean. Second, most single-belt cleaners are specified too late in the design process (indeed, some after the system is operational). This complicates matters since cleaning efficiency is directly proportional to when they are specified: the later the specification, the less efficiency. Cleaning equipment should be taken into consideration before the conveyor's structure is designed and fabricated. Otherwise the space available to install adequate cleaning equipment at the head pulley may be inadequate. Instead of matching conveyor with proper cleaner (as would occur during the design of the conveyor itself), designing a cleaning system "after-the-fact" becomes a matter of matching cleaner to conveyor. This limits choices in cleaners and, therefore, overall cleaning effectiveness. This is why after-the-fact designs of single belt cleaners are costly and rarely successful. While it is always best to specify belt cleaners during early design stages, the multiple-cleaner systems approach makes the timing of cleaner installation less critical. Because of flexible mounting hardware, a well-designed system can lead to 99% efficiency in cleaning and put an end to carryback even after a system is operational. Multiple-Cleaner Systems Approach In a multiple-cleaner system approach, the first step is to achieve a thorough understanding of the material to be moved under the worst conditions. With such un-

Jan 4, 1984

By E. Gutierrez, P. Gillies

Asset Maintenance Readiness (AMR) provides a tailored reliability and maintenance strategy specific to operational needs. AMR delivers reliability and maintenance foundations for the plant and equipment before start-up. Having a dependable reliability and maintenance strategy before start-up is critical, particularly in those first weeks and months during ramp up to stable production. The Asset Maintenance Readiness is the integration of Reliability and Maintenance Engineering analysis/studies at the earliest stages of the new Production System concept and design and during the Capital Project CapEx phases; adding this analysis to the Capital Project CAPEX cost, will have an impact of 2% to 3% of total project cost, but will deliver a good compendium of benefits far from the AMR costs, and those results will be shown upon commissioning and during the life cycle of the plant.

Mar 2, 2022

By M. Misra

The coral contaminated with plutonium at Johnston Atoll UA) was subjected to gravity and flotation separation processes at the Soil Washing Laboratory (SWL) and also at the Johnston Atoll UA) site. Tests were conducted with the contaminated coral fractions referred to as the "HP-l" ( hot particles) and the "sludge". The gravity process tested was centrifugal gravity separation and the flotation processes were conventional Denver mechanical flotation and tall column flotation. Flotation tests were conducted using both fresh and sea water. Industrial fatty acid (anionic collector) was chosen as collector to make plutonium-enriched particles hydrophobic. The use of flurosilicic acid and sodium silicate made the clean coral hydrophilic. The results show that each of the processed when tested with appropriate size fraction and operating conditions resulted in passing the success criteria. It was possible to obtain more than 80% weight of the original coral as "clean sand" having activity below the JA site "soil screening level" of 13.5 pCi/gm. The field tests spiked with plutonium particles showed remarkable success. The effect of depressants, flotation medium and the coral pretreatmentis described. Finally, a flowsheet developed by the University of Nevada, Reno to treat 8000 tons of HP-l pile presently stored at JA is presented.

Jan 1, 1996

By J. Wiebmer

Some thoroughbred racehorses are great routers (distance runners), others are sprinters. Some racehorses perform best on turf, others on dirt, and some in mud. To be a winner, you have to choose the right horse for the course. It's no different when looking at an electric cable shovel, a hydraulic shovel/excavator, or a wheel loader. Each loading tool has its own zone of application. To be a winner, you have to choose the right horse for your course.

Jan 1, 1993