Search Documents

By Michael Gay

Right in the heart of Boston Harbor lies Deer Island, where a ten-year, 6 billion dollar sewage treatment plant is under construction. The 9.5 mile long, 25.5' diameter Effluent Outfall Tunnel is the center piece of this program. A Robbins double-shielded TBM is currently driving this challenging tunnel some 400 feet below sea level. This paper will discuss the set-up and operation of this Tunnel Boring Machine in driving the longest single heading tunnel ever built in North America.

Jan 1, 1993

By David A. Rice, Scott A. Shuey, William K. Tolley

The U.S. Bureau of Mines (USBM) is developing new dewatering technology to permit the recycling of iron values contained in wet steel plant sludges. In laboratory tests, Q-BOP fume sludge was dewatered to 12% moisture by displacing water with acetone in a plate-and-frame pressure filter. Acetone is reclaimed through distillation at lower cost than conventional thermal drying of the sludge. The projected additional energy requirement for acetone treatment of the sludge, including acetone recovery, is $5 to $7 per dry ton.

Jan 1, 1995

By James K. Grunig, Rodney J. Anderson

A process consisting of leach, continuous countercurrent decantation, resin-in-column ion exchange, evaporative crystallization of beryllium sulfate, and decomposition of the sulfate was developed for Spor Mountain, Utah, ores. The process is metallurgically sound, has a minimum of process steps, and is applicable to a wide variety of beryllium ores. The most novel aspect of the process is a resin system of ion exchange which is highly selective for beryllium and which rejects substantially all impurities except for minor amounts of aluminum, magnesium, fluorine, and sulfate in addition to beryllium. The oxide from sulfate decomposition meets specifications of potential users.

Jan 1, 1983

By Klaus Schönert, Martin Botsch

In common high intensity magnetic separators, the magnetic particles are deposited on ferromagnetic matrices, such as expanded metals, steel balls or grooved plates, inserted into a strong magnetic field. The nonmagnetic material is flushed through the matrix chamber. Discharging the magnetic particles is only possible if the magnetic field is reduced to zero (e.g. high gradient magnetic filtration for the purifying of kaolin) or the matrix chamber is moved out of the field by a rotor (e.g. the Jones Separator). Therefore, these separators perform only in a batch or semicontinuous mode. A real continuous operation requirs transport of the deposited magnetic material to an outlet where it can leave the separation chamber inside the field. One possibility for accomplishing such separation and transport is through the use of a rotating induction body with a certain shape, such as a spiral.

Jan 1, 1995

By R. H. King, D. R. Schricker, R. E. Cameron

Mine managers rely on their experience, section foreman's daily reports and occasional time studies to make important production, maintenance and forecasting decisions. This information is often subjective and imprecise, consumes expensive engineers time, is often biased and is restricted to short time periods. Managers need better information. Furthermore, if a recently purchased machine is being evaluated, a large increase (>10%) in productivity may be obvious, but small increases are usually masked by other variables. In today's highly competitive markets, cumulative small changes are important, especially since managers have already exhausted most available, obvious avenues of improvement. A technique to separate these charges from effects of other variables and to quantify the target effect is necessary. CSM researchers are addressing this need by developing an intelligent decision support system (IDSS). It provides key production and maintenance information to support management decisions by recognizing patterns in mining machine sensor data and representing knowledge about mine management, operations, layout and equipment. A continuous miner section at Western Fuels-Utah Inc.'s Deserado Mine in Rangely, CO is the test facility for the research. Power transducers located in the sections load center provide kilowatt versus time data from continuous section equipment. The IDSS pattern recognition algorithms classify the kilowatt versus time patterns into individual machine operating modes. It produces an output similar to a typical industrial engineering time study but continuously, automatically and without an engineer in the section. It is relatively easy for a time-study engineer to identify the stop and end points of a cycle element and classify it by looking at the machine and glancing at a stop watch. The problem is that monitoring system hardware and software do not have these unique capabilities. Consequently, IDSS algorithms must automatically define the begin and end points of machine tasks and identify the task by recognizing patterns in kilowatt versus time data. However, many mines have file drawers of time-study type data that are not very useful. So, IDSS contains the knowledge representation subsystem (IDSS/KRS) to produce short reports containing only key information. This is difficult because mine environments continually change and information requirements differ for each management level. Consequently, IDSS/KRS must learn and adapt to new conditions in a dynamic mining environment. Western Fuels-Utah owns and operates the Deserado Mine, located about 19 km (12 miles) northeast of Rangely, CO (Upadhyay, 1988; King and Eros, 1988). One longwall and two continuous miner sections produce about 900 kt (1 million st) of coal annually for the Deseret Generation and Transmission Cooperative's 4000 MW power plant located near Bonanza, UT. Three mine monitoring systems control the underground mine, the preparation plant and the unit train load out. Pattern recognition IDSS/PRS produces a listing of begin and end times for each machine operating event as shown is Table 1.

Jan 1, 1991

By K. Norrena

Grade control in open pit mining requires the specification of dig limits that account for mineral grades, economic costs, and selectivity of mining equipment. Visual identification of ore rock types is ideal, but this is not always possible in lower grade disseminated deposits where ore/waste contacts are not visually discernible. In this case, conventional grade control practice consists of a two-step procedure (1) create a map of mineral grades at some selective mining unit scale, and (2) determine practical ore-waste boundaries or dig limits on the basis of the gridded block grades or assay information. This procedure is laborious, depends on a subjective assessment of where the boundary should be, and may be economically sub-optimal. We pose the determination of dig limits as an optimization problem and solve that problem with the technique of simulated annealing. Simulated annealing has the unique advantage of being able to combine multiple non-linear constraints into a single objective function. We use maximum profitability and the ability of the equipment to mine the proposed dig limits as constraints in the determination of optimal dig limits. We require a map of expected profit for eah block. Geostatistical techniques are recommended, for mapping expected profit but not necessary. Geostatistics will provide a quantification of the uncertainty in the grades within rock types using all available blasthole samples and exploration drilling. Some variant of L-optimal estimation or kriging can be used to determine the block-by-block classification that is economically optimum. We also need the expected profit for each block. It is unrealistic to assume free selection, that is, each block cannot be extracted independently of its neighbors. The optimal balance of ''accepting dilution'' and ''wasting ore'' is achieved to maximize profit subject to equipment constraints.

Jan 1, 2001

By Rajiv Hadkar, M. D. McKinley, J. B. Hiskey, B. J. Scheiner, G. W. Warren

Flyash from municipal solid waste incinerators containing roughly 13 to 15% Zn, 2% Pb and 0.2% Cd is an attractive material for simultaneous metal recovery and detoxification. Results have shown that Pb in flyash is present as PbSO4 and PbC12 and that about 70% of the Zn is present in the form of soluble amorphous compounds. Leaching results in a number of acid and basic lixiviants show that acid leaching is clearly more effective than basic leaching which is limited by low solubility of Cd and Zn. Cementation in acid solution with pH < 1 promotes redissolution of the precipitated metal. Successful zinc electrowinning from chloride leaching solutions has also been demonstrated, although Pb2+ and Na+ can be potentially detrimental. The presence of Pb2+ can prevent deposition of metallic Zn, forming zinc oxychloride, ZnC12.4Zn(OH)2, instead. High concentrations of Na+ can also result in precipitation of NaCl. This investigation has shown that hydrometallurgical treatment of MSW flyash through leaching, cementation and electrowinning is a potentially feasible method for simultaneous detoxification and recovery of metal values. Several issues have also been identified which would require further investigation for final process development.

Jan 1, 1993

By Thomas Oberndorfer

Recent publications indicate that there is a rising interest in the field of mining method selection, and increasing efforts are being undertaken to develop satisfying solutions. Yet, computer assistance for mining method selection (MMS), or in other, terms assistance in the (pre-)feasibility state of a project, still lags behind the computer application in other mining activities. This is true for research as well as for application. This paper is intended as a contribution to the development in computer-assisted mining method selection, and focuses especially on underground hard-rock mining. It is structured in four main parts. The first deals with general aspects of mining method. selection within the process of mine planning, and with problems and requirements which derive from this specific situation. In the second part some numerical MMS-approaches hitherto published are briefly introduced, and investigations on these approaches are discussed. Based on .these experiences, in the third part an analysis of the complex system MMS is presented. It focuses on heuristics, influencing factors, objectives, assessment-routines and mining methods, and emphasizes the essential necessity of a profound mining method description (MMD) specially developed for the requirements of MMS and numerical processing. Accordingly the fourth part of this paper presents a mining method description model developed at the Department of Mining Engineering, Montan-University Leoben (MUL), Austria. It describes the consequences of the investigation, in particular the new mining method description model, on &apos;the design of a MMS-system. The paper closes with a outlook on the possibilities of an successful MMS-system being realised.

Jan 1, 1992

By J. F. T. Agapito, R. R. Goodrich

Yield pillars have been used for many years to help reduce stresses near mine openings and improve roof and floor stability. A yield pillar is often defined as a pillar that fails but retains residual strength. Stress transfer occurs through the roof and floor after the peak strength of the pillar is reached. High stresses are transferred from around the openings onto abutments that can be barrier pillars or unmined ground. This mechanism, often referred to as pressure arching, is possible as long as the width of yield pillar mining (panel width) is less than the critical width above which stresses cannot be carried by the overburden. Significant stress transfer also can occur due to small amounts of pillar and/or floor yielding before the peak strength is reached. This is accomplished in a quasi-elastic manner with little or no visible roof and pillar fracturing or floor heave. Long-term stability may be achieved when stresses and mechanical properties are favorable to prefailure yielding. This paper gives practical examples where improvements in stability and resource recovery were achieved with this mechanism. Yielding was assessed by comparing measured and calculated vertical pillar stresses. Results indicated that calculated stresses in the pillars were 25% to 40% higher than the measured stresses, demonstrating significant arching load transfer to the abutments. Prefailure yielding is probably often present but unintentional in both development and production areas. Better recognition and use of this mechanism should lead to design improvements, as mines become deeper.

Jan 1, 2003

By Ross W. Smith, Salim Akhtar

Flotation of oxide minerals, particularly silicates, with cationic collectors differs substantially from classic flotation of sulfide minerals using sulfhydryl collectors. In the case of cationic flotation of these minerals, in general: 1. There is a greater importance of electrostatic interaction between mineral and collector. 2. Longer-chained collectors are required; as a rule at least 10 carbons must be present in the hydrocarbon chain. 3. Moderate concentration of collector is required. 4. Attachment between collector and mineral appears to be less strong even though the system may exhibit a large contact angle. 5. Required conditioning time before flotation is usually relatively short. 6. There is sensitivity to slimes. 7. The collectors usually possess frothing power. 8. Selectivity of cationic collectors for specific minerals is usually poor. Almost any of the oxide and silicate minerals may be floated using cationic collectors. However, specific response to these collect- ors varies with mineral type. The following classes and minerals are

Jan 1, 1976

By G. H. K. Pearse

Long range transport of pollutants, particularly of sulphur dioxide and the associated acidic precipitation, has received much attention in the press and in international discussion during the last few years. Studies revealing increasing acidity of lakes and the dying out of fish populations over broad regions of the eastern half of North America have created alarm. In this paper, I will not attempt a description of the acid rain phenomenon. For this r recommend the balanced treatment of the subject by Gene Likens et al (1979) in Scientific Americana For my purposes I accept that the problem is serious and direct my attention to exploring a solution. Ultimately, the key lies in the answer to the question; "What do we do with the enormous tonnages of pollution abatement byproducts, chiefly sulphur compounds, that would arise from pollution control?"&apos; Little thought has been given to this most limiting factor to environmental clean-up. This is symptomatic of a basic flaw in the [philosphy] that under-ins environmental policy. Although this paper is to propose a solution to the abatement byproduct problem, the basic flaw - the firmly entrenched, universally adopted, &apos;polluter pays [philosphy] as it is currently [understood] - needs some comment.

Jan 1, 1981

By R. Ciccu

Permeable reactive barriers (PRB) are one of the most promising systems for groundwater remediation. PRB are constructed with the purpose to intercept the contaminated flow and to degrade it as a big reactive filter. The most common type of reactive barriers is realized by excavating a trench and by filling it with a substance able to treat the contaminants dissolved in the water. Another type of PRB is obtained by realizing a line of wells in which chemically active compounds are injected. A new method for barrier construction has been studied at DIGITA?s laboratories. It makes use of the waterjet technology to increase soil permeability and to inject active compounds. This technology is especially suitable in the case of deep contaminated aquifers where traditional construction methods are difficult to apply. The paper describes the experimental apparatus especially designed and constructed and the activities carried out to investigate the relationship between waterjet operative parameters and the penetration of the jet in the soil. In conclusion, on the basis of the experimental results, the economical feasibility of the technique is evaluated.

Jan 1, 2008

By David Morrison

On the Corramandel Peninsula of New Zealand, the Waihi Gold Mine has undergone a major redevelopment. The upgrade included the construction of two very large overland belt conveyors, both rated for a capacity of 6000tph. The first of these conveyors (CVR2) traverses a total of 1600m over undulating terrain, including a significant section running through tunnels. A large hill is climbed, just after the mid-section of the conveyor run, before dropping back down prior the discharge point. The second of these conveyors (CVR8) traverses 1100m along an alignment with a horizontal curve, a number of vertical curves and a significant lift before the discharge point. The CVR8 conveyor also included a shuttling head pulley arrangement. The mine they service is inside the town of Waihi. The conveyor alignment runs through the town and out to the metallurgical process site on the outskirts of the municipal area. This paper documents the engineering process that took place in the design of these conveyors. The Martha Hill mine in Waihi, New Zealand is unique. The mine is placed in the township. Consequently there are quite stringent environmental limitations on the mine&apos;s operation. In [Figure 1] the proximity of the mine to the town is shown. In the top-centre of the photograph the alignment of the existing smaller overland conveyor can be seen leading from the mine to a tunnel through the hill in the background.

Jan 1, 2000

By Stephen LaBrooy, David Muir

Gold ores in the geologically more recent rocks are often associated with copper minerals which pose problems of high reagent consumption with conventional cyanidation practice. Many examples exist in northern Australia, Indonesia, Papua­New Guinea, Chile, and Brazil where, despite various treatment options (LaBrooy, 1992), the processing of oxide and transition ores is uneconomic either for copper or gold recovery. Hence, there is a need for a reagent which is selective for gold without leaching copper minerals. The ammonia-cyanide system appears to meet this criterion (Muir et al, 1989; LaBrooy et al, 1991; Costello et al, 1992; Hayes and Corrans, 1992) but it has proven difficult to optimise and apply to a variety of ores due to differences in the mineralogy and reactivity of ores and a lack of understanding of how the system works. Recent work on the mechanism, however, (Muir et al, 1993) has thrown a new light on the problem which should allow better process control. Ammonia­cyanide mixtures behave neither like free cyanide nor free ammonia and too much of either reagent in the mixture is detrimental. The key to the process is understanding how ammonia enhances gold extraction yet inhibits copper extraction in an essentially cyanide environment.

Jan 1, 1993

By G. B. Amicucci

Golden Sunlight Mines Inc. operates an open-pit gold mine and cyanidation plant about 11km (7 miles) northeast of Whitehall, MT. Golden Sunlight is a subsidiary of Placer Dome US Inc. Mining is accomplished with conventional open pit drilling, blasting and hauling methods. The mining rate is about 102 kt/d (113,000 stpd). Gold occurs as fine-grained disseminations in a pipe-shaped breccia and in immediately adjacent country rock. The ore body is low grade, averaging 2 g/t (0.059 oz per st) of gold. The metallurgical plant uses conventional carbon-in-pulp (CIP) technology. Daily throughput averages 6.5 kt (7000 st). Recoveries are enhanced through a sand tailing retreatment facility while a preaeration process reduces operating costs. The low grade ore dictates that maximum mill throughput at the desired grind size be maintained. Therefore, in October 1988, an Armco Autometrics (now Denver Autometrics) particle size monitor (PSM) 400 was commissioned. The PSM 400 is an on-line instrument. It measures particle size and percent solids in a slurry stream. The PSM pulls its own sample, deareates the sample and passes it through diametrically opposed ultrasonic sensors. The unit uses ultrasonic sound to measure the deareated slurry stream&apos;s particle size and percent solids.

Jan 1, 1991

By D. Christofferson

As an alternative power source to eliminate trailing cables, ESD Corporation is installing a flywheel system on a shuttle car. Flywheel power is extracted by a high-speed generator, developed by Lear Siegler Corp,, and the system -- including vacuum and lubrication and cooling auxiliaries -- is supplied by the aerospace group, Rocketdyne Division of Rockwell International. The flywheel system is being developed under a three-year contract with the Department of Energy. It is a follow-up contract to a previous DOE-contracted study by General Electric Co. in which it was shown that a flywheel can be a feasible power source for a shuttle car from technical, economic, and safety standpoints. This paper addresses the status of the program, design decisions established, and plans for laboratory test procedures and underground demonstration. The flywheel-powered shuttle car is a conventional 6-ton capacity shuttle car equipped with a 7-rotor flywheel energy storage package. The energy package is the sole source of power for the shuttle car through a complete mission duty cycle (MDC) of tramming to the miner, receiving a load of coal, and returning to the secondary haulage system. Energy stored in the system exceeds MDC requirements and waiting times to provide an ample margin of reserve energy. The energy storage system is recharged by spinning the rotors back up to maximum speed each time the shuttle car comes back to the secondary haulage system. The electrical charge motor is connected to a power source to recharge the system while the load of coal is being discharged.

Jan 1, 1982

By D. Christofferson

As an alternative power source to eliminate trailing cables, ESD Corporation is installing a flywheel system on a shuttle car. Flywheel power is extracted by a high-speed generator, developed by Lear Siegler Corp., and the system -- including vacuum and lubrication and cooling auxiliaries -- is supplied by the aerospace group, Rocketdyne Division of Rockwell International. The flywheel system is being developed under a three-year contract with the Department of Energy. It is a follow-up contract to a previous DOE-contracted study by General Electric Co. in which it was shown that a flywheel can be a feasible power source for a shuttle car from technical, economic, and safety standpoints. This paper addresses the status of the program, design decisions established, and plans for laboratory test procedures and underground demonstration. The flywheel-powered shuttle car is a conventional 6-ton capacity shuttle car equipped with a 7-rotor flywheel energy storage package. The energy package is the sole source of power for the shuttle car through a complete mission duty cycle (MDC) of tramming to the miner, receiving a load of coal, and returning to the secondary haulage system. Energy stored in the system exceeds MDC requirements and waiting times to provide an ample margin of reserve energy. The energy storage system is recharged by spinning the rotors back up to maximum speed each time the shuttle car comes back to the seconaary haulage system. The electrical charge motor is connected to a power source to recharge the system while the load of coal is being discharged.

Jan 1, 1981

By M. Bleeck

Calcium carbonate (CaCO3) is one of the most ubiquitous and versatile minerals found in the earth&apos;s crust. Its availability, attractive physical properties and relatively low processing cost make CaCO3 the most widely used filler material today. It is mined in three different forms - chalk, limestone and marble. Each physical form of CaCO3 has different qualities due to differences in postdepositional geology. But the chemical composition remains the same, with CaCO3 an inert component of the finished product. In the past, the paper industry largely left CaCO3 by the wayside, as it cannot withstand the acid-based papermaking process. But conversion to an alkaline system by many US mills changed this picture. Carbonate suppliers have put time and effort into research and development, demolishing barriers and creating new possibilities for what is a simple, natural product. By controlling particle size, size distribution and particle charge, the industry uses ground calcium carbonate (GCC) as a performance enhancer and as an extender for more expensive ingredients. It is estimated that the United States uses 3.6 to 4.1 Mt/a (4 to 4.5 million stpy) of CaCO3. Consolidations and mergers are taking place in the industry. Of the 12 major GCC producers in operation nine years ago, seven are left. Mineral Technology (US) is the dominant precipitated calcium carbonate (PCC) producer with more than 50 satellite plants worldwide. Other producers include Georgia Marble (French); Franklin Industries (US); OMYA (Swiss); J.M. Huber (US); ECC (English); and Filler Products (US). Global Stone PenRoc (Canada) is the only newcomer. In addition to this group, there are three small producers left in North America, each with a capacity of less than 100 kt/ a (.110,000 stpy). The trade organization operating as the Pulverized Limestone Division of the National Stone Association renamed itself the Pulverized Mineral Division, to increase its membership pool. The US paper industry is a predominant GCC con¬sumer, using approximately 800 kt/a (882,000 stpy) at an approximate cost of $130/t ($1.43/st). European paper mills pioneered alkaline papermaking. In the early 1960s, they began using GCC as filler and soon thereafter added GCC to their coating formulations. A decade later, the North American paper industry followed suit. The conversion from acid to alkaline paper production benefits the economic and performance aspects of the industry. Less pulp is needed, paper machine maintenance and effluent treatment costs are reduced, and sheet strength, opacity and brightness are increased. Perhaps most important to the reader, the sheet is desensitized to ultraviolet light, extending the paper&apos;s archival ability. CaCO3 can provide the papermaker with additional control of his paper. For example, PCC has long supplied the tobacco industry with a means to slow down the burning rate of cigarettes. Due to enhanced performance with regard to bulk and opacity, filler PCC use has risen to 1,500 kt/a (1,650 stpy) in the United States, at an approximate price of $130/t ($143/st). The majority is produced onsite at the paper mill, using "satellite plants." This concept reduces freight cost because only quicklime (CaO) is shipped to the mill, not CaCO3 slurry. The future of CaCO3 is encouraging. The amount of natural ground CaCO3 used is expected to double by the year 2005 to approximately 8 Mt (8.8 million st) worldwide. Acid papermaking practices will feel an increasing pressure to convert to an alkaline process as larger volumes of GCC containing paper enter the recycling market. CaCO3 reserves are plentiful. They will supply the ever growing demand for increasingly sophisticated paper. The plastics industry is supplied with almost 900 kt/ a (990,000 stpy) GCC at an annual growth rate of 4% to 5%. The price of a functional, inorganic filler, surface modified for the plastics industry, has an average selling price of $220/t ($243/st). GCC represents the most common filler, creating a product with higher gloss, better dielectric properties, impact resistance, weatherability and shrinkage control. CaCO3-filled plastics surround us - auto hubcaps and dashboards, shower enclosures, floor tiles, wire coatings, microwave dishes and Tupperware. The caulking and sealant industry is an enormous GCC user, with annual consumption requiring 1.13 Mt (1.2 million st) at about $44/t ($48.50/ st). Caulking and sealant may be highly filled with GCC yet undergo no adverse flow effects, with a narrow particle-size-distribution filler decreasing the binder demand. The CaCO3 industry, as well as the carpet industry, are more or less tied to the growth rates of the construction industry. It is estimated that the carpet industry uses some 680 kt/a (750,000 stpy) of GCC at about $25/t ($27.50/st). The paint industry uses approximately 300 kt/a (331,000 stpy) at a 1 % to 1.5% annual growth rate. Here, too, GCC is the dominant filler. It is used to enhance flow characteristics and color uniformity. It also extends costly titanium dioxide, creates sheen and controls roughness, hardness and tack. More CaCO3 should be used in the future as industry shifts from solvent-free or water-based formulations that can accommodate higher GCC volumes. CaCO3 is not imported or exported in any great quantity. Most areas have reserves of their own and the selling price is relatively low. Even so, quality varies from deposit to deposit. As our needs become morespecific, it remains a challenge to provide varying industries with a fitting product.

Jan 1, 1998

By Panshi Xie, Yingyi Zhang, JIANJIE DUAN, Shenghu Luo

The most important safety aspect associated with great mining height in steeply dipping coal seam mining is the stability and control of the roof. When soft coal and hard gangue make up the immediate roof of a working face, the soft-coal interlayer plays a significant role in gangue damage and can cause problems such as roof collapse in front of the support, collapse of partial area supports and other problems that can affect the stability of the supports and the surrounding rock system. This study found that the first weighting step of a multigangue roof is larger than that of a nongangue roof, but periodic weighting steps are similar. The overburden collapse height is lower in a multigangue roof than in a nongangue roof due to the buffering and supporting function of the collapsed gangue. Failure of the coal interlayer is the key factor in the collapse of multilayer gangue. The limited load of the interlayer and maximum resistance of the support is concluded by the hard gangue and soft coal interlayer mechanical model. The maximum resistance of the support increased with the dip angle of the seam and burial depth. Certain measures are proposed to control the stability of the gangue roof, including zoning control of the mining height and resistance and advancing the support while maintaining roof contact, thus ensuring the integrity of the support and surrounding rock system.

By Dean Brox

The Galore Creek Mine project is one of the newest major mining projects under development in Canada. The project is located in a very remote area of northwestern British Columbia and is being developed by NovaGold Resources and Teck-Cominco of Vancouver. The mine project comprises one of the largest and highest grade undeveloped porphyry-related gold-silver-copper deposits in North America. In order to access the mine site a new 120 km road is required including a 4.4 km mine access road tunnel. Glaciers with heavy snow pack cover approximately two-thirds of the tunnel alignment with a maximum cover of 1200 m. The size of the access road tunnel is about 50 m2 and has been designed as a large single lane road tunnel to accommodate the transport of large size mining equipment for mine start up and ongoing operations. The rock conditions along the tunnel alignment comprise very strong volcanic rocks. Key services for mining operations will be incorporated into the tunnel comprising diesel and power as well as the concentrate pipe-line. Structural portal canopies and portal houses have been incorporated into the tunnel design due to the risk of rockfalls and avalanches in the portal areas. The mine access road tunnel is a significant and critical-path component to the overall project to provide vehicular access to allow construction of the mine site. In order to meet the expected mine start up date the construction of the tunnel works have commenced prior to any other works at the mine site and will be constructed entirely by helicopter support. The tunnel works commenced in the summer of 2006 with the advanced excavation of the overburden materials at the portals. Tunnel construction from the North portal commenced in the spring of 2007. When completed, the mine access tunnel will be the longest private road tunnel in North America. The key design and constructability issues for the mine access road tunnel project are presented and discussed along with a construction status update as of late 2007.

Jan 1, 2008