Search Documents

By D. C. Yang

A practical and economical flowsheet has been developed and demonstrated by integrating the packed column flotation with the GranuFlow process for fine coal recovery. Orimulsion, which was used as an additive, served a dual purpose: first in the flotation and second in the dewatering and granulation steps. The test results on the coal preparation effluent sample show that Orimulsion is flexible and compatible with fuel oil and various frothers used in the packed column. Clean coal with ash contents of 3.0, 3.7, 4.3 and 5.1% were produced from a head sample of 33% ash at combustible matter recoveries of 72.4, 81.1, 87.5, and 89.2%, respectively. Other advantages include high throughput, low moisture, improved handleability, and reduced dustiness of the dewatered coal, thus providing a very significant economic Incentive for the integrated process.

Jan 1, 1998

By Y. Wang, G. Xu, N. A. Amoah, A. Kumar

Mining-induced coal dust causes various respiratory diseases to mine workers, such as coal workers’ pneumoconiosis (CWP). Current available underground monitors are expensive, heavy and only measure mass concentration. These disadvantages limit them for regulatory sample monitoring purposes only while personal exposure levels for most miners remain unknown, risking miners to potential overexposures. Low-cost light scattering PM sensors offer a potential solution to this problem with capability of high spatio-temporal resolution PM characterization. However, these sensors require careful calibration before they can be applied in mining environments. There is basically no comprehensive study in the literature using a standard protocol assessing these sensors for coal dust monitoring. With the aim of calibrating the PMS5003 sensors for coal dust monitoring, we design the calibration method and system to calibrate these low-cost PM sensors coal dust monitoring. Working principles of present coal dust monitor and low-cost sensors are presented in detail. The linear regression calibration model which is used for the sensor calibration is further described. Sensor calibration and evaluation protocols are comprehensively compared and discussed. This investigation reveals the feasibility of low-cost sensors for real-time personal coal dust monitoring in underground coal mines.

Mar 2, 2022

By W. A. Crosby

The ability of open pit mines to steepen overall final wall angles allows significant cost reductions as a result of reduced waste movement requirements. Final wall angles are principally controlled by three factors: geological conditions; hydrological conditions; and wall control blasting practices. The first of these factors is not controllable by the mine operator, the second can be influenced to some degree, but the last one certainly can be controlled, hence the current interest in final wall blasting practice at many mining companies. This paper discusses common blasting techniques employed to steepen final pit walls and outlines the attractiveness of moving from small hole high cost systems to the use of full size production drills as a means of reducing wall control blast costs. Attempts to make this change have been limited at many mines by the physical size of the drills and their inability to reverse drill. In the past, pres pi it, pre-shear or trim holes have had to be drilled vertically, at considerable distance from the upper bench toe, with the result that inter-berm face stability is reduced and final wall angles have to be made somewhat more shallow than desirable. The paper concludes with a description of how these problems can be overcome by utilizing the new Bucyrus 39R which has the capability of drilling at a ?15 degree angle underneath the machine. It is concluded that the resulting wall control blast designs will offer large mines improved final wall angles with resulting significant overall cost reductions.

Jan 1, 1998

Despite two large projects represented in the keynote docket, the mood of the 2011 SME Arizona Conference was summed up best by Ferol Baker, general manager of New Mexico Copper Corp. (a wholly owned subsidiary of Themac Resources Group), ?In the past, it seemed like you couldn?t go to a conference like this without hearing about one big new greenfield project after another. Now what you see is companies doing internal expansion or small-scale brownfield development.? Overall, the tone of this year?s meeting, held at the J.W. Marriott Resort at Starr Pass in Tucson, AZ, was upbeat, yet practical. From the keynote and luncheon addresses to the six panels of sessions, the projects described were positive about the future, yet focused on the details required to make those projects come to fruition.

Jan 1, 2012

By M. J. Virnig, G. A. Kordosky

Throughout time, the mining industry has been very successful in meeting the world's requirements for metals and materials while meeting the challenges of decreasing ore grades and increased emphasis on protection of the environment. This success has been due to the development and implementation of new technologies. A clear example of such a development over the past 25 years is the increasing use of leaching/solvent extraction/electrowinning for the recovery of copper from oxide and sulfide ores. The key to the successful introduction of this technology was the discovery and development of the hydroxyoxime liquid ion exchange reagents by General Mills Chemicals (now Henkel Corporation). An important role was also played by the close working relationships between General Mills Chemicals and Ranchers Exploration which resulted in startup of the first plant in 1968 and between General Mills Chemicals and Bagdad Copper which resulted in the startup of the second copper SX-EW plant in August of 1970. Following on the heels of the hydroxyoxime development came the commercialization of other new chelating reagents based on different chemical functionalities, i.e., beta-diketones, alkylated 8- hydroxyquinolines and sulfonamidoquinolines. This initial spurt of activity was then followed by a slowing of development in terms of new reagent functionalities. Activity has continued in terms of further optimization/improvement of existing reagent functionalities but the commercialization of new reagent functionalities has slackened. This observation reflects the fact that the development of new reagent functionalities for metal recovery has become increasingly more expensive such that the right combination of price and sales volume must exist in order to justify the investment required to bring a new reagent to the market place. Given the dependence of the mining industry on innovation to meet the needs of the future, one can ask how these new developments, particularly in new reagents, will occur. To arrive at an estimate of the costs involved in commercializing a new metal extractant functionality, particularly a chelating type functionality, a case study of the development of LIX ®* 34

Jan 1, 1994

By G Luxbacher

Computer simulation of mine ventilation systems is rapidly becoming an essential tool in mine planning and design. This paper examines the utilization of ventilation simulation techniques to evaluate the number, shape, size and layout of mine entries in a typical coal mining system. Since the mains and sub-mains serve mainly for transportation and ventilation and the ventilation system is critically important to the health and safety of the workers, there exists a great need for optimal designs in this area. Evaluation criteria, could include, among others, minimization of power costs, shaft requirements and leakage. Constraints of this optimization problem include health and safety regulations and production and mine infrastructure requirements.

Jan 1, 1977

By J. C. Haptonstall

The Bismark Mine is located in northern Chihuahua, 150 km southwest of Ciudad Juarez. The ore deposit was discovered in 1979, and was placed in production in 1992. The production rate is about 2400 tpd from an ore reserve of 8.5M tonnes. Grades average about 8 % Zn, 0.5 % Pb, 0.2 % Cu and 50 g Ag per tonne. Substantial inflows of water into the under-ground mine complicate the operation. Complex metallurgy poses another challenge for the operators. Bismark was operated through a joint venture, Minera Bismark, S.A. de C.V., with U.S. and Mexican partners, but since early 1993, it is wholly Mexican-owned and operated.

Jan 1, 1994

By C. M. Brown

The semi-autogenous grinding circuit at the Utah Mines Limited, Island Copper Operation, located on Vancouver Island, British Columbia, is described. Since start-up of the operation in 1971 grinding circuit throughput has been progressively increased from the initial design rate of 30,000 to the current average 45,000 tonnes per day (t/d) of porphyry copper ore. Key developments and modifications in operating and maintenance practice that have contributed to this increase are reviewed.

Jan 1, 1985

By Shuangchun Yang, Le Tong, Ronggui Fan, Cunlei Li

Acid mine drainage (AMD) is difficult to treat due to its physicochemical characteristics, such as high pH and high heavy metal concentrations, so it causes great harm to the environment and human health. If acid mine drainage is discharged arbitrarily without treatment, it will lead to a series of environmental problems and cause long-term environmental pollution. In this paper, the source and hazards of acid mine drainage are introduced in detail. And the principle, the mechanism, the application, and basic information of the current primary technology of the treatment for acid mine drainage are comprehensively introduced and summarized. The summarized treatment technologies for acid mine drainage mainly include neutralization, sulfidization, constructed wetland method, adsorption method, microbiological method, ion exchange method, membrane technology, and microbial fuel cell technology. Also, the primary technology of treatment for acid mine drainage is systematically compared and evaluated. Moreover, some suggestions on the development direction of water treatment technology in the future are put forward. This paper provides a scientific reference for scientific and technical works to treat acid mine drainage.

Sep 4, 2020

By H. H. Richards, Ray L. Tobie, L. A. Thomas

GENERAL DESCRIPTION Since the beginning of operations, with the exception of a small tonnage mined by slushing, ore extraction has been by full gravity caving. Formerly, a checkerboard sequence of block undercutting was followed with the even-numbered blocks in one panel and the odd¬numbered blocks in the adjacent panel being mined. As these blocks were depleted, the intermediate or pillar blocks were mined (Fig. 1). Following this checker¬board, the mining sequence went through a number of changes, finally evolving into diagonal retreat panel cav¬ing by blocks (Fig. 2). The numbers in Fig. 2 indicate the sequence in which blocks were undercut. Gaps in the numbering sequence indicate undercutting on the level outside the illustrated area. Geology The ore body is a low-grade deposit of chalcopyrite mineralization disseminated throughout structurally weak, highly fractured, strongly altered granitic host rocks. It takes the shape of a gently dipping elliptical cylinder consisting of an ore shell of variable thickness surrounding an interior waste core. Major and minor axes of the mineralized cylinder are 1524 m (5000 ft) and 762 m (2500 ft), respectively, and length approximates 2438 m (8000 ft). Ore is sufficiently fractured to break readily into medium-coarse size. The igneous rock complex containing the ore body is covered by a wedge-shaped blanket of Tertiary con¬glomerate which was brought into place by faulting along the major regional structure of the San Manuel fault. Thickness of the conglomerate cap varies from only 9 m (30 ft) at the east end of the ore body to more than 610 m (2000 ft) at the west. Structurally, the con¬glomerate is much more competent than the igneous host rocks and, when caving, it breaks into massive chunks. Conglomerate boulders seen in drawpoints underground are very coarse. The total rock column over the initial mining area of the 1415 grizzly level was 354 m (1160 ft) of which 122 m (400 ft) was ore, 79 m (260 ft) was leached igneous capping, and 152 m (500 ft) was conglomerate above the San Manuel fault. Diamond Drilling: From 4572 to 7620 m (15,000 to 25,000 ft) are drilled annually from underground workings to delineate the ore body. MINE DEVELOPMENT Haulage Level In the south or main ore body (see Figs. 3-6), with the exception of the draw and transfer raises, all the extraction openings are concreted (Seaney and Tobie, 1965). The haulage panel drifts, which are 18 m (60 ft) below the grizzly drifts, are first driven with pre¬concrete ground support. The drift, which has an arched section, then is concreted using mobile collapsible steel tunnel forms. The haulage drifts leading from the pan¬els to the hoisting shafts are not concreted. After the panel drifts have been concreted, the raise stations from which transfer raises will be driven are constructed and the raise-station ore-drawing chute is installed. The chute is prefabricated of A-36 steel with undercut guillo¬tine gates made of abrasion-resistant 2.5-cm (1-in.) steel plate powered by 20-cm (8-in.) air cylinder installed on each side of the raise station. Transfer Raises The transfer raises are lined with 15 x 20-cm (6 x 8-in.) cribbing and are 1.22 m (4 ft) in the clear. Each cribbing is protected from wear by a high carbon steel angle which is nailed onto the cribbing. The transfer raises are driven from each side of the raise station on an angle of 1.1 rad (63°). Each raise con¬sists of a main and a backover branch. The transfer¬raise driving crew consists of two men working one shift only. Grizzly Drifts After the transfer raise reaches the grizzly level, the grizzly drift can be driven. The grizzly drifts are spaced at 10.6-m (35-ft) centers and are driven parallel to the long axis of the ore body (see Fig. 2). This drift is driven by a two-man crew working on one or more drifts at a time using feed-leg machines. The eight grizzlies in the 42.7-m (140-ft) long drift are spaced at 5.3-m

Jan 1, 1982

By D. Lawrence, H. Lawrence, G. Saevil

Plant operators in the mineral processing industry have been implementing expert systems for several years now, with the intent to increase production and reduce costs. Most systems have been installed on grinding circuits of some type and have proven that the technology is viable in that application. However, few applications on other processes have been attempted for various reasons, such as lack of reference sites, complexity of the process, lack of suitable measurements and lack of confidence in the technology. The successful application of an expert system on an Alumina Calcining kiln is the first such application in the West Indies Alumina Company (Windalco), and demonstrates how this technology can be successfully applied to other processes. The key objective of an expert system is to optimize the process. To achieve this the process must first be stabilized, followed by optimization of the operating parameters. The steps taken by this expert system to optimize the process are: • Check for abnormal conditions and deal with them using a prioritized set of special actions. • Use a selection of rule blocks to stabilize the process. • Once the process is stable, achieve additional benefits through further optimization of the process. The potential benefits that a user can expect to achieve through installing an expert system can be assessed on the basis that performance will improve from that of an "average operator" to that of the "best operator" performing at his optimum for 24 hours a day, every day. The quantifiable process benefits include: • Increased production • More consistent product quality • Reduced operating costs • Reduced standard deviation of key variables • Consistent plant operation The success of this project was measured in several ways: project implementation, realised economic benefits, and realised non-economic benefits. With a commitment to maintain the system over the long term, the longevity of the system is assured and will become an important part of the Alumina Calcining control strategy at Windalco. This paper discusses the various phases of implementing the ABB Expert Optimizer expert system, what the benefits were and the procedure that is in place to maintain the system to ensure continued long term success.

Jan 1, 2002

By David Jurich, Ed Perko, Jacob Prezkuta

Numerous Colorado mountain tunnels that date to the late 1800s convey water to the farming and urban communities of the eastern Front Range. Repairs to these remote facilities, often located in public lands at altitudes of 11,000 feet or more, require detailed planning, close coordination with multiple agencies, and creative execution. Issues and solutions discussed include designing repairs in undocumented ground and support conditions, logistical challenges, work in a short summer construction window, stabilization of historically signicant structures, and proect delivery strategies. xamples that illustrate early contractor involvement, exibility in design, and construction solutions are presented.

Jun 23, 2024

By M. Pope

By 1950, packaged oil and gas fired boilers were on the market for capacities up to 30,000 lbs./hr. By 1962, capacities were up to 100,000 lbs./hr. and even higher when separate heat traps (economizers and air preheaters) were attached to the boiler packages. During this period, complete packaged coal fired boilers were developed into the 10-15,000 lbs./hr. range. Oil and gas fired plant designs became very compact, "basementless", and far: less costly than the coal fired plants of any capacity. Coal fired plants remained large and expensive, required field erection of boilers and required basements. With the spectacular strides made in automation, oil and gas plants became far less costly to operate, requiring only the part-time attendance of a single operator. Some advances were made in coal fired plants, but not to the degree attained by the fluid fuel competition.

Jan 1, 1965

By E. Kenneth Siroky

The concept of ultrasonic measurement was originally applied to marine operations. Sonar . . . standing for Sounding, Navigation and Ranging, was developed for military uses. Today Sonar has become very important to the fishing fleets and marine construction industries where its applications cover a wide range of uses our company, in addition to the inair ultrasonic equipment as discussed in this paper, is also deeply involved in marine sonar and works primarily with oceanographic research and fishing industries. Ultrasonics, by simple definition, are sound waves beyond the audible range of the human ear and are generally accepted to be waves over 20,000 cycles per second. When applied to level measurement, the principles of ultrasonics are basically quite simple. A sound pulse is initiated at a point in time and the time interval for the echo from that pulse to return can be interpolated into distance. The speed of sound in air under standard conditions is approximately 1,100 feet per second, or if converted into more meaningful information as related to distance measurement, the time required for sound to travel one foot round trip is 1.78 milliseconds. An early application for ultrasonic level monitoring equipment was in large grain elevators. Prior to ultrasonics, the common practice of inventory measurement was to have an employee walk around the top of these large grain elevators, which are often over 100 feet above ground level, and drop a weighted rope or chain down into the silo to determine the level of the grain. Needless to say, this was a slow process and could be extremely unsafe, especially during windy and snowy weather conditions. An alternate

Jan 1, 1971

By John Sasadi

The mining industry depends upon inexpensive water transportation. Today, large quantities of mined products are transported by ships over oceans, from continents to continents, over lakes and waterways to the ultimate users. Sometimes, the routes these Bulk Carriers travel cover only a few hundred miles, sometimes thousands of miles halfway around the world. Most of the products of the mining industries are relatively inexpensive. A significant portion of their cost to the ultimate users are in the cost of transportation and not in loading and unloading these commodities at the ports of origination or destination. So far, the industry has produced very efficient loading and un- loading installations, but has very little influence over marine transportation or the design of the vessels themselves. Very little was ever published dealing with integrated transportation systems properly correlating all phases of the operation; namely, loading, marine transportation and unloading bulk materials.

Jan 1, 1967

By Richard L. Gordon

Coal supply analysis has since about 1973 become a major activity of many scholars and consulting firms. The present paper is an effort to explain in as nontechnical fashion as possible the state of the art and what implications, if any, the research has for those actually engaged in producing coal or regulating the industry. l The discussion stresses the coal supply side of the models and makes limited comments about other elements in the analysis. To orient the appraisal, it is desirable to recall the features of coal supply that an adequate model should capture. The first considerations are the locational aspects of the industry. Transportation costs can, in some cases, exceed the production costs of coal, and thus any adequate model must incorporate a treatment of the economics of transporting coal from one location to another. A second major issue is that of the heterogeneity of coal; models should treat as well as possible such key differences among coals as their Btu and sulfur content. Third, we recognize that, with given technology and labor, capital, and supply costs, an expansion of the supply of a given type of coal in a specific region will occur only if prices rise. This is the familiar proposition of textbook economics that supply is an increasing function of price. Finally, over time, changes in technology, input cost, and depletion interact to cause changes in the price of given amounts of coal. Economics represents the net effect of this process by a shift over time in the supply curve. During the 1950s and 1960s, the trend was to reduce the production costs of a given output; subsequently costs rose sharply.

Jan 1, 1977

By Edwin W. Tooker

Creation of needed new resources will be accomplished mainly by imaginative and diligent geologic exploration because geologic availability is the key determinant of future mineral supply. Adequate resources of most commodities can be made available for the rest of this century and beyond if they are discovered. Thus conversion of hypothetical and speculative resources into available reserves will provide the principal challenge to earth scientists. Additional problems now compete for our attention. First is a challenge to discover more resources than have been found to date for domestic needs as world-wide demands increase exponentially and as easily found high-grade deposits are rapidly being depleted. New ways to find new types of deposits are required. Second, the United States, a resource importer, increasingly is challenged for access to foreign supplies through stiffening competition and economic or expropriation sanctions. Balancing needs for mineral supply and environmental protection is a third challenge. Geologic explorers must consider statutory as well as economic and technologic requirements, controlled access to public and private lands, competition with urban sprawl or wilderness, limitations on discovery, appraisal and mining methods, and restoration of mined areas. Finally, is the challenge to temper public and private attitudes and assure that decisions bearing on resource problems are based on comprehensive credible facts. While striving to maintain and improve the standard of living, many Americans appear to disdain and mistrust those organizations that provide their material where-withal. Meeting these challenges effectively, and in time, will require careful appraisal of the resource system and the joint efforts of industry, university, and government earth science research.

Jan 1, 1974

By S. Peng, N. Vayenas, A. Farah

"While genetic algorithms have been widely adopted in ore grade estimation and optimization, mine design, and production scheduling in the mining engineering field, reliability and maintainability analysis of mining equipment using genetic algorithms has been a relatively new research area in recent years. This paper presents an application of genetic algorithms using case studies with seven underground scoop trams whose maintenance records have been collected over a period of 12 months from an underground mine in the Sudbury mining area. Based on the assumption that various factors that contribute to machine failures resemble the biological evolution process, the authors have developed an in-house PC software application called GenRel which adopts genetic algorithms in its programming. In this study, the authors feed the historical maintenance data into GenRel in order to predict future maintenance characteristics of mining equipment in a time period of three months. Then the predicted maintenance characteristics are compared to the actual maintenance records in the same time period. A statistical study is then used to examine the similarity between the predicted data and the recorded data.INTRODUCTION Today maintenance costs of sophisticated engineering systems are so high that maintainability draws great attention from scientific researchers to operations managers. For instance, a study by [1] shows that American manufacturers spend more than 300 billion U.S. dollars on plant maintenance and operations. Therefore it is understandable that the main objectives of applying maintainability principles to engineering systems are to reduce projected maintenance costs, to use maintainability data to estimate system or equipment availability/unavailability and to determine labor-hours and other related resources needed to perform the projected maintenance. A system with better maintainability would inherently provide the benefit of lower maintenance costs, less time to recover with lower breakdown frequency (design for simplicity), less complexity of maintenance tasks and relatively reduced man-hours [2]. Most maintainability functions use the Time To Repair (TTR) as the independent variable. It is common to use probabilistic or statistical concepts to define a maintainability function, for example, the probability density function. Let t denote the time. Assuming a repair starts at t=0 and completes at time T, the maintainability can be mathematically defined [3] as in Equation (1)."

Jan 1, 2015

By A. Perry

Latin America is in the path of economic growth characterized by increased privatization, joint-venture projects, and reduced trade barriers. Privatization is changing the industrial operating mode from Government-owned/Government-operated to a privately-owned/government-regulated regime. The establishment of joint ventures, such as in construction and management of infrastructure, energy and mining projects, and deregulated industries (electricity/gas/ telecommunications), is now a common practice in the region. These changes, coupled with the growing awareness of environmental protection issues, have led to a sincere effort on the part of the countries of Latin America to establish reasonable environmental regulations and controls (RERCs) for all industries, including mining and energy, for the benefit of present and future generations. However, RERCs require further consideration of many factors with respect to environmental, geologic, economic, and social impacts in the region. The process must find a balance between the need to sustain profitable operations and the need to adequately protect the environment. While striving to find a balance between continued industrial profitability and environmental protection, the RERCs must be scientifically sound, pragmatic, flexible, and enforceable. There has been worldwide attention focused on the environment, and international symposia have been held on such issues as global warming, water pollution, air pollution, and hazardous wastes. Organizations such as the United Nations (UN) and the Organization of American States have performed rather extensive studies on the environment for various industries and activities, and have developed some broad general plans to address environmental concerns. This technical information is available for the asking, and should be considered a starting point for countries embarking on the passage and enforcement of their own RERCs.

Jan 1, 1998

By Kefton H. Teague

An article entitled "The Rule of the Geologist in the Industrial Mineral Field" by G. R. Gullet, was published in the August, 1967, issue of the Canadian Mining Journal. Mr. Gullet defined industrial minerals as follows: "Industrial minerals are largely non-metallic minerals and rocks that find value because of their physical or chemical properties." This definition is brief, but all-inclusive. Mr. Gullet continues, "They include all useful minerals and mineral commodities except those used as fuels and those from which metals are extracted. Factors in the evaluation of an industrial mineral deposit are generally as different from those used in the evaluation of a metal deposit as is the assessment of a potential oil field. The key to the successful development of an industrial mineral, deposit is more often a balance of accessibility, transport, and proximity to markets than to any natural quality advantage of the deposit itself."

Jan 1, 1972