Search Documents

By N. M. Cheimanoff

GEOCAD is an ambitious research program aimed at the development of a computer based system assisting the geologist and the production or planning engineer. BONANZA, its mining part, is a computer production scheduling tool (short to medium term) of particular relevance to complex orebodies. The principle is to simultaneously use a powerful information management system (CAD potentialities) and small expert modules integrating the exploitation context and the engineer's knowledge (Artificial Intelligence tecniques). As an illustration, a module of mineable block determination for underground exploitation is discussed.

Jan 1, 1989

By W. J. Stone

In response to concerns over the impact of mining on the hydrologic balance at the Navajo Mine in northwestern New Mexico, a recharge study was conducted using a chloride mass- balance approach. Impact of mining on annual recharge volume was assessed by comparing pre- and post-mining recharge values. The mean regional recharge rate for reclaimed ground (weighted by acreage) is 1.02 mm/a (0.04 in. per year) or twice that for undisturbed ground, 05 mm/a (0.02 in. per year). Comparison of regional recharge volumes for identical areas shows mining increases recharge 92%. The increase is only 80% if no closed depressions are constructed during reclamation. However, the increased rates are so low that there should be no detrimental impact on regional water resources. The chloride method proved useful at Navajo Mine and should succeed at others surface coal mines as well.

Jan 1, 1991

By T. Skodack

This presentation will compare actual work site results for the loading and transport of shot rock for two major tunneling projects in North America. "SCARMAR" (the Canadian subsidiary of S & M Construction) is operating a rail bound Hagglund continuous gathering arm loader in combination with a Hagglund nine car shuttletrain system at the West End of Table Mountain on the B.C. Railway project near Tumbler Ridge, Canada. Al Johnson Construction is operating a Hagglund rubber tired continuous gathering arm loader in combination with haul trucks at the Rocky Mountain Pump Storage Project near Rome, GA. This paper will compare: 1) tunnel and ground conditions, 2) the total work cycle as it relates to mucking and haulage 3) efficiencies and related problems with the two systems 4) mucking and haulage rates 5) operating costs, and 6) recommendations for future large tunnel excavations. Manuscript not received in time for publication.

Jan 1, 1983

By John Kinneen, Sunghoon Choi, Arne Fareth, Edward S. Barboe, Kyle R. Ott

A new water treatment plant is to be constructed for a portion of the water supply system of New York City. The project includes construction of new water conveyance tunnels crossing perpendicular and sub-parallel to the existing pressurized water tunnel at two locations. A study was conducted to evaluate the impact of new tunnel construction on stability of the existing tunnel and hydrojacking potential in the surrounding rock mass. This paper introduces a practical approach to evaluate tunnel interaction, expressed in terms of rock-liner interaction, stress-induced stability and hydrojacking failures. A simple method to evaluate hydraulic and mechanical properties of concrete liners and jointed rock mass is also presented.

Jan 1, 2007

By L. Piga, P. Cipriani, F. Pochetti

High-temperature roasting of alunite in the presence of K2CO3 gives rise to a reaction that results in up to an 80% recovery of its potassium content as K2SO4 by leaching of the roasted mixture. K2SO4 is also generated from the reaction between the added K2CO3 and the SO3 driven off during roasting of the alunite. This limits the environmental and corrosive problems involved in the thermal treatment of this mineral. A solid residue containing mainly aluminum oxide is also obtained. This could be used as raw material for the production of aluminum, as the use of K2CO3 does not introduce different cations than are in the ore. A statistical study was performed on the factors assumed to affect the recovery of potassium, namely, roasting temperature, K2CO3- alunite stoichiometric ratio and leaching temperature.

Jan 1, 2000

By G. H. Schnakenberg Jr.

In response to the underground mining industry's growing concern with the exposure of workers to the diesel particulate matter (DPM) component of diesel exhaust, a method was developed to estimate the average workplace concentration of DPM that could be expected from using the new lower DPMemitting engines now being approved by the US Mine Safety and Health Administration (MSHA) when these new engines are equipped with state-of-the-art exhaustcontrol technology for filtering and combusting DPM. The resulting estimate uses the MSHA-reported particulate index for these engines, the prevailing rule-of-thumb ventilation rate of 150 cfm/hp and the available diesel-exhaust filter technology that has been shown to be at least 80% effective in reducing tailpipe DPM. In the estimate calculation, every engine used in an underground mine is assumed to be equipped with this control technology. Under the stated reasonable conditions, an average DPM level of 90 µg/m3 (mass) is predicted as technically feasible.

Jan 1, 2002

By Thomas E. Shufflebarger

Glass sand is a virtually pure, fine- to medium-grained, quartz sand. It is produced in 25 states from a variety of chemically different source rocks. Deriving their raw material largely from either friable sandstones or loosely consolidated sands, 59 operations produced 14.9 million tons of melting sand in 1976. About one-third of this tonnage was obtained from the Oriskany and St. Peter Sandstones. Glass-sand prospects are discussed in this paper with regard to chemistry, environment, transportation, and costs. Demand for a quality product will range from 36 million to 46 million short tons in 1995.

Jan 1, 1978

By H. Michael Breza

Texasgulf Inc. installed bucketwheel excavators and overland conveyor sysems at its Aurora, NC phosphate mine o increase the productivity and flexibilty of the surface mining operation. This ;ystem has significantly improved overrall. Its flexibility is evidenced by adapation to operation requirements, such is mining area moves, movement of xcavated overburden to designated ites, selective handling of overburden, poll placement contouring, and proiding an environmentally sound and afe operation. The system's productiv:y is evidenced by case studies relating. overall production, excavation rates nd cost-effectiveness. There are many competing alternaves available for excavating uncon)lidated overburden: truck-shovel, raglines, dredges and bucket wheel ticavators. These alternatives also may used in tandem to recover reserves icated at greater depths.

Jan 1, 1993

By Malcolm Scoble, Sean Dessureault, Scott Dunbar

Budgets are key financial and behavior drivers for most businesses, including mining. Budgets are used to link strategic objectives to tactical decisions, to measure performance, and to provide basic financial planning. More accurate and pertinent budgets should result in improved strategic decision making and performance measures. This paper discusses how a process based production and cost database, based on activity based costing models and the one year production plan, can be used to create the annual budget for an operating mine as an Activity Based Budget (ABB). A case study is used to compare budgets derived from traditional methods and an ABB approach. It is evident that the ABB method is more accurate.

Jan 1, 2002

By N. K. Riddle

In many mines, it is typical to stockpile material for milling based either on analyses from exploration and blasthole drilling, or on the observation and judgment of experienced personnel. New analytical instruments make it possible to perform multiple, rapid analyses of as-mined samples at or near the mining face, so that sorting into stockpiles can be much more accurate. Using data and operating practices from a phosphate mine, a model was developed to simulate the function of analytical instruments in ore-grade control and ore stockpiling. With this model, it is possible to determine the recommended sampling points and sample frequency to obtain the desired confidence limits on the stockpile analyses.

Jan 1, 2003

By H. Colijn

Vibratory or oscillatory conveyors can be found in all types of industry, handling virtually any granular bulk material, often at elevated temperatures. These conveyors can be combined with other process functions, such as screening, cooling, drying and dewatering, while conveying. Although construction and installation is relatively simple, the engineering and design analysis of the vibratory mechanics is fairly complex. This paper will discuss the basic types of vibratory conveyors and the analysis of the material movement along the carrying trough.

Jan 1, 1985

By Stephen Stone, Kerby Dobbs, G. Richard Whittecar, W. Lee Daniels, Zach Agioutantis, Tess Thompson

A common result of Environmental Impact Assessments associated with mining projects is the construction of new wetlands in areas disturbed by mining operations. Where appropriate, this mitigation may be considered an integral part of the mine reclamation process under the principles of sustainable development in the minerals industry. Wetbud is a new tool for estimating wetland water budgets using available weather data and site-specific topographic, soil and geohydrologic data, coupled with mass balance mathematics. Wetbud is primarily intended as a planning tool for use in the design of created wetlands, but it can also be applied to native wetlands or wetland restoration sites where the required input parameters can be specified. Wetbud can be run in its basic form where wetland topography, soil parameters and groundwater flux are simplified, or in the advanced form, where these parameters are included in a more complex approach via integration of the MODFLOW package, a free 3D program that was developed by the United States Geological Survey. Both versions can also include overbank flow hydrology sources and the advanced form can also model sloping and irregular topography. The program downloads weather data from the nearest applicable station and selects appropriate wet-normal-dry (W-N-D) years following a modest user data clean-up step. Wetbud also has the ability to utilize existing short-term (e.g. 6 to 9 months) groundwater data from an up-gradient well to simulate longer-term groundwater level inputs for the selected W-N-D years. In addition, Wetbud features a “Wizard” version that comes pre-loaded with 14 pre-selected weather data sets for all areas of Virginia that can develop a simple monthly water budget in less than 15 minutes – a feature that could be expanded anywhere geographically with historic weather data.

Jan 1, 2017

How do you think the US Bureau of Mines closing will affect SME? The demise of the bureau represents a challenge, an opportunity and, above all, new responsibilities for our profession. A lot of good professionals are seeking new positions. A lot of worthwhile research is available for transfer to the private sector. Logic dictates that worthwhile projects of any defunded government activities should find support in the private sector. The bureau may be gone but its legacy is deeply rooted in the profession. The bureau’s contributions will be remembered as long as there are mines and miners. Its1994 research program was divided into three major areas: environ-mental technology; health, safety and mining technology; and minerals and materials science. There must be a place in either the government or private sector to continue these worthwhile activities.

Jan 1, 1996

By S. Shrivastava, R. G. Reddy

Spent potliner is generated in the electrolytic process of reducing alumina to make aluminum metal using molten fluoride electrolytes. Spent potliner(SPL) is obtained at the end of the pot's life. The SPL contains small amounts of cyanide and fluoride, which present environmental problems. Spent potliner could possibly be used as a fluidizer to replace calcium fluoride (CaF2) in the iron- and steelmaking industry and in the glass industry. A low viscosity and a low melting point are prime requirements for such an application. In the present study, viscosity measurements were performed. The effects of various additives, such as sand, limestone, dicalcium silicate dust and MgO baghouse dust, on the viscosity of SPL were studied. The results showed that the addition of sand and limestone can produce a very high fluidity SPL melt at significantly lower temperatures. The results suggest that spent potliner mixed with additives could potentially be used as a substitute fluidizer.

Jan 1, 2002

By John Brouwer

Through the use of good preventive maintenance procedures in which the work of both production and maintenance personnel is well-coordinated, production downtime can be drastically minimized, and costly repairs and interruptions in planned maintenance and production schedules can be eliminated. There had been some conflict in the past between production and maintenance people over the proper method of achieving maximum machine performance. The usual practice was to operate production equipment at maximum capacity for the longest possible time until breakdown occurred, and then make hurried repairs to get back into production. In most cases, these repairs involved unscheduled work and were thus performed inefficiently. Both production and maintenance have the same objective: to produce a quality product at maximum efficiency and at minimum cost. Preventive maintenance is a common tool available for both production and maintenance personnel to achieve this objective. Actually, one of the main objectives of preventive maintenance is to find any abnormal machine condition that may cause machine failure before a breakdown occurs. This makes it possible to plan and schedule maintenance work with the least amount of interruption and plan production volume with a higher rate of accuracy. Maintenance people prefer to perform this work on a scheduled basis and get away from the "crash" situation that accompanies breakdowns. They thereby increase the utilization of available manpower and machine time, prolong equipment life, and improve maintenance costs.

Jan 1, 1979

By J. Wickens

This paper discusses how Bald Mountain Mine dramatically reduced mercury production by treating process solutions with a liquid reagent called UNR 811A. The reagent is marketed by Cherokee Chemical Co., Inc. A summary of the bench tests comparing several different reagents is given. The ensuing plant trial is discussed and results are presented. The plant trial treatment costs are discussed. Finally, potential cost savings are discussed.

Jan 1, 2001

By Joel K. Waterland

GENERAL DESCRIPTION Homestake Mining Co.'s operations are at Lead, SD. Production from the various methods used are: 1 155 753 t/a (1,274,000 stpy) by open cut-and-fill, 68 039 t/a (75,000 stpy) by square set cut-and-fill, 144242 t/a (159,000 stpy) by shrinkage stoping, 107 048 t/ a (118,000 stpy) by blasthole stoping, and 67 132 t/a (74,000 stpy) in development work for a total of 1 542 214 t/a (1,700,000 stpy). Mining takes place from the 616-m (2000-ft) level to the 2073-m (6800 ft) level (Fig. 1). The average travel time to the stope is 45 min. GENERAL ORE BODY REQUIREMENTS AND LIMITATIONS Size, Shape, and Dip of Ore Body Six major ledges varying from 914 m (3000 ft) long by 228.6 m (750 ft) wide to 305 m (1000 ft) long by 122 m (400 ft) wide are mined. Within these ledges are irregular-shaped areas of varying sizes. These ledges dip at approximately 1.2 rad (70°) to the east and plunge to the south from 0.26 to 1.57 rad (15° to 90°). Ground Conditions The ore is cummingtonite (chlorite schist) which is very competent except for major bedding planes and fracture patterns. The footwall is a slate but because of the dip presents very few problems. The hanging wall is also a slate which because of the dip and bedding is very weak and requires considerable rockbolting. No problem has been encountered with rock bursts to a depth of 2438 m (8000 ft). Ore Value The ore values vary somewhat from ledge to ledge, but the average ore delivered to the mill is approxi¬mately 6.2 g (0.2 oz) of gold per ton. A small amount of silver is the only byproduct of this operation. Annual production of gold is approximately 10 575 183 g (340,000 troy oz). Production Requirements The mine has a mill capacity of approximately 1 723 651 t (1,900,000 st) but because of several fac¬tors (manpower, depth, etc.) this mill capacity has not been attainable for the past several years.

Jan 1, 1982

By R. Herrera-Urbina, D. W. Fuerstenau

A large number and a wide variety of chemical reagents are used in flotation processes for wettability and Eh control, particle agglomeration/dispersion and bubble stability. A historical account of the use of flotation reagents through the years since flotation was introduced as a viable and economic process for the concentration of sulfide minerals is given and a review of old and modern postulates of their interaction with minerals is presented. Although the results of surface and colloid chemistry studies with well characterized mineral/flotation reagent systems have advanced our understanding of the role played by these chemicals in the flotation process, many questions remain unanswered. Moreover, new flotation reagents are needed to solve the challenge posed by the treatment of problematic-type ores and fuel deposits that have increasingly become the source of our raw and energy materials. Because of the depletion of high-grade and relatively easy-to-process ores, flotation scientists and engineers are confronted with finding more specific and selective flotation chemicals to effectively and economically concentrate minerals. The development of new flotation reagents is vital for cleaning fine coal and processing polysulfide, polymetallic ores, and mixed oxide/sulfide ores.

Jan 1, 1989

By L. John Minnick

Extraction of crude ores and minerals inevitably produces various by-products either as a result of nonusable residues or as waste by-products from process operations. Thus for each 100 tons of coal extracted in a strip mine operation, one can expect to produce 25 tons, or more, of mine refuse. In addition, the amount of ash produced from the burning of coal will represent 10 to 20 percent of the weight of coal burned. With the advent of lime/limestone scrubbers now being installed on many power plants, an additional by-product is produced that in most instances is equal in volume to the sluiced fly ash. Statistics developed by the National Ash Association have indicated that sluiced waste from power plants in the United States currently exceeds 25 million tons per year (dry basis). Overall mineral industry statistics (copper mines, etc.) indicate better than 200 million tons per year. In the past it was general practice to send most of these waste materials to holding ponds or lagoons simply as a means of disposal or "throwaway" of unwanted by-products. Unfortunately modern society has reached a stage where these large quantities of waste materials are creating monumental environmental and economic problems that need urgent attention. Among these problems are concern for loss of future usable land, pollution of ground water, loss of potential mineral reserves, and loss of opportunities to recycle or use these by-products for the benefit of future generations. An example of the latter is the serious shortages of construction quality aggregates that can be replaced with some of the by-products produced from waste materials from the extractive and chemical industries.

Jan 1, 1975

By Eleanora I. Robbins, Motoaki Sato

Many problems associated with acid mine drainage (AMD) are caused by the complex way molecular oxygen (O2) oxidizes reduced matter at surface temperatures. In aqueous solution, O2 kinetically "prefers" to go through the formation of hydrogen peroxide (H2O2) as an intermediate. Being innately unstable, H2O2 is quickly decomposed back to water and oxygen in the presence of dissolved Fe and Mn, both catalysts for the decomposition. Direct addition of H2O2 to AMD produced similar results. Ozone (O3) is a much faster and stronger oxidizer than either O2 or H2O2. In the laboratory, O3 rapidly precipitated Mn, Fe, Ni, Co, Pb, and Ag even in acidic solutions. The experiments indicate that AMD can probably be processed with ozone and metal oxides/hydroxide recovered in flow systems using only septic-tank-size reactors and small sedimentation ponds.

Jan 1, 2000