Search Documents

By M. Noaparast, F. Woodcock, A. R. Laplante

A novel methodology for estimating gold recoveries in gravity-separation circuits is presented. The methodology makes use of a population-balance model. The model represents gold liberation, breakage and classification behavior and applies preconcentration and recovery performance curves to gravity-recoverable gold. The derivation of the necessary parameters is explained and demonstrated using data from an actual gravity circuit and from a projected application. The methodology makes it possible to estimate the performance of a gravity circuit having a large gold circulating load and a relatively-low unit recovery (e.g., a jig) or having a high recovery on a bleed of the circulating load (e.g., a Knelson Concentrator).

Jan 1, 1996

When solid pillar is not left to separate different mining levels in underground mine with high dip angle deposit, waste rock in the backfilled stope could be a safety hazard to future mining activities on levels above or below the backfill. Different backfill methods can be used to eliminate this hazard according to the deposit shape and mining method. Building concrete pillar in ore drift of each mining level is one of them. Concrete pillar had been constructed in underground mines based on operational experience. Little design literature and pillar performance data can be found. At Great Basin Gold Hollister Mine, over two thousand feet of concrete pillar had been constructed. The project started with engineering design which combined civil engineering concrete design and the specialties of underground construction. Time Domain Reflectometry technique was installed to monitor the pillar movement and concrete cylinder samples were collected and tested for quality control. Engineering design, underground construction, quality control and concrete pillar monitoring, as well as precious concrete mixing data from years of experience are fully covered in this paper to give a general frame of concrete pillar method.

Jan 1, 2010

By F. Ferella

In this paper several leaching tests were per-formed to optimize the leaching section of a hydrometallurgical process for the recycling of alkaline and zinc-carbon batteries. Zinc and manganese oxides were dissolved by an acidic-reductive leaching using sulphuric acid and oxalic acid as reductant. Leaching tests were developed according to a full factorial design. The operational variables were pulp percentage, sulphuric acid concentration, temperature and oxalic acid concentration. Additional tests were performed to evaluate the precipitation rate of Mn and Zn oxalates. Finally a hydrometallurgical process were proposed for the recycling of alkaline and zinc-carbon batteries, in which Zn and MnO2 are recovered from purified solution by electrowinning: Zn is recovered as metallic compound, while Mn can be recovered as electrolytic manganese dioxide (EMD), but recovery of further manganese compounds is possible with simple process changes.

Jan 1, 2006

By John A. L. Campbell

Although there has been an increased interest in the electrokinetic properties of coal (1) research on the subject is still in an early stage of development (2,3,4,5,6,7) To the author's knowledge, no electrokinetic studies have been made on coal lithotypes - particularly anthracite lithotypes. This paper presents the results of an investigation of the double layer properties displayed at the anthracite/water interface (whole coal and lithotypes) as determined by streaming potential methods, It is hoped that this investigation and related future investigations will provide correlations from which the surface properties of any coal can be predicted and then related to surface dependent processes such as froth flotation and flocculation. Another aspect of this research, undertaken to determine the physical and chemical parameters necessary for anthracite lithotype differentiation, was previously published (8). The number of parameters involved, lithologic, organic and inorganic, and the wide divergence of these parameters within an individual coal limits the practical utilization of the results, however, the results are of value and of interest in guiding theoretical developments. Keeping the limitations in mind, the results are analyzed in terms of their application to froth flotation processes and are used to indicate the feasibility of making a lithotype separation by flotation.

Jan 1, 1969

By Mike D. Adams

Testwork was conducted on loaded carbon samples from a small gold mine in South Africa. It was shown that a 75% saving in reagent consumption in the Zadra elution circuit could be achieved by adopting a cyanide-free elution approach, i.e. by cutting back the NaCN level from 1 % to nil, and the NaOH level from 3% to 1 %. This process change was also shown to result in a 20% improvement in the elution kinetics. Furthermore, it was also shown that a 50% enhancement in elution rate over the current situation could be achieved by use of an eluant containing 0.5% NaOH and 0.15% NaCN, corresponding to an 84% saving in reagent consumption. A further improvement in elution kinetics was found to occur by increasing the NaCN level to 3%, but this would lead to a concomitant increase in reagent consumption, due to the decomposition of cyanide at high temperatures. The presence of base metals loaded onto the carbon was also found to have a significant effect on the elution. Copper tends to adsorb as Cu(CN)2- during the adsorption stage, and acid washing converts this species to CuCN. Copper in this form is not eluted during cyanide-free elution, whereas it is eluted during a conventional cyanide elution, consuming the initial cyanide in the process. The elution data was analysed and the fit to a simple model was verified.

Jan 1, 1995

By Owen E. Owens

INTRODUCTION This paper deals with the main components in exploring for and developing a gold ore deposit. It addresses geology, exploration drilling, ore reserves, and evaluation criteria in an integrated manner to present an overall picture. Gold forms such a small component of a gold ore body, that particular care should be taken in dealing with the data from a developing deposit. The paper lists the main gold ore deposit types and their character. Their differences, as well as differences to other types of ore deposits, are important to understanding exploration approaches, and problems of ore reserve definition. Gold exploration has enjoyed a great boom in recent years. Many new ore deposits have been developed but experience shows that definition of gold is not a simple straight forward process and this outline attempts to point out some of the important aspects of ore reserve definition including some pitfalls. GOLD DEPOSIT TYPES The Witwatersrand deposits in South Africa produce about 50% of the world's gold. The gold occurs as fine grains in thin beds within gently dipping quartz pebble fan conglomerates usually with associated pyrite grains. It is characterized by rather uniform distribution of gold along thin layers within the conglomerate.

Jan 1, 1988

By S. K. Kawatra, J. A. Halt

"INTRODUCTION Iron ore beneficiation needs advances in areas such as process control, automation, burner and furnace designs, silica-free binders, and even alternative iron making routes. While some – like new binders – are only step-changes, all are tools that can help make the ironmaking industry more sustainable. This paper focuses on binders. Binders are added to iron ore fines before they are agglomerated. Binders are used to control the balling process and increase the mechanical quality (e.g. strength) of green-balls and pellets. Agglomeration usually follows thickening and filtration. Good-grade ores, which don't require upgrading, are wet ground to decrease particle size and increase specific surface area. Low-grade ores are often extensively upgraded through wet operations (flotation, dispersion and selective flocculation, magnetic separation, etc.). For both types of ores, thickening and filtration conclude the circuits so that moisture contents are lowered and the ores can be agglomerated. It's been known for a long time that thickening and filtration behaviors are influenced by zeta potential (Sandvik, 1979). Highly-negative zeta potential is good for dispersion while low zeta potential is good for filtration. So, the zeta potentials of iron ore particles are lowered with additions of acid or carbon dioxide, for example, to increase filtration rates and throughputs (Eisele et al., 2005). What happens to particles as their zeta potentials are lowered? Particles aggregate together, effectively forming larger particles. How stable then, are those aggregates during mixing and balling? Are they easily broken up during mixing (if mixers are even used)? Are they broken up during balling? Or, do the aggregates resist breakage so that the availability of ultra-fines, which are so beneficial for agglomeration (Stone, 1968), is decreased? For plants where high doses of bentonite are used as binder, the above questions may be of no concern. The bentonite adds the necessary amount of fines; however, even at those plants, the calcium and magnesium contents in the water affect bentonite's effectiveness (more magnesium and calcium means less effective bentonite). (Engesser, 2003) For plants where new silica-free organic binders are being developed and used, the above questions may need to be considered. The binder is only amongst the iron ore particles for a short period of time – until it burns away or thermally decomposes in the induration furnace – so the liberation, availability and distribution of fine particulates is very critical for the quality of balls and pellets. It was hypothesized that high zeta potential conditions would lead to good pellets, while low zeta potential conditions would lead to relatively bad pellets."

Jan 1, 2018

By J. A. Meech, C. A. Harris

Expert Systems are being used in the Mineral Industry with ever­increasing frequency. A major advantage of these systems over conventional computer programs is that the knowledge and intelligence of human experts can be captured directly onto a computer for transfer to novices or other lesser experts. These programs allow rapid construction of process models that are not well-understood in fundamental terms, but for which good operational reasoning exists. In addition, user-friendly access to "high-tech" knowledge can be provided to unsophisticated personnel who otherwise might be turned off by unintelligible jargon. As such, these systems can be important training tools for new operators. This paper describes the features of Expert Systems that relate to gold processing plants. Applications include grinding circuit control, supervisory control of reagent addition and pulp density, monitoring and control of CIP/CIL carbon inventories and the operation of carbon stripping and regeneration facilities. A consultative Expert System is described that provides advice on laboratory cyanidation testwork

Jan 1, 1992

By W. J. Halvorsen

Means for minimizing the disadvantages of thermal drying are suggested. The other ap¬proach of substituting other techniques in place of thermal drying is also discussed. Recent devel¬opments in fine coal screening dry down to 3.2 mm (0.125 in.) and 2.0 mm (10 mesh) offer an econom¬ical means in certain cases.

Jan 1, 1988

By K. H. E. Kroemer

Selecting persons who are unlikely to suffer an overexertion injury is one of three methods to reduce the risk of musculo-skeletal disorders in manual material handling. This paper describes the underlying models, methods, and techniques for such personnel selection. In particular, it describes the isoinertial LIFTEST in which persons actually lift weights to assess their capability for doing so on the job.

Jan 1, 1985

By A. T. Visser

The expansion of surface mining has led to the development of very large off-highway trucks currently capable of hauling payloads in excess of 290t. Mine haul roads have historically been designed empirically, relying heavily on local experience; the trend in increasing truck size will thus render the current pavement systems inadequate. Since truck haulage costs can account for 10%-50% of the total costs incurred by a surface mine, not only would the maintenance costs of existing roads of inadequate design increase, vehicle operating and maintenance costs would also increase prohibitively. There is thus a need for improved design technologies encompassing the construction and management techniques of mine haul roads, appropriate for the wheel loads of vehicles now in use. The aim of the paper is to present the different components of a mine haul road design and management system and to demonstrate the value of its application through case studies. The system has been applied at several South-African surface mines and distinct benefits have been derived. The improved structural design of a new road resulted in a 29% saving in construction costs and also provided better service, whilst the optimal selection and management of wearing-course materials provided better functionality at lower total transportation operating costs.

Jan 1, 1999

By B. C. Flintoff

In general, process control systems in solid-solid separation have not evolved to the same level as in flotation circuit control. Perhaps one of the more significant contributing factors in this regard is the lack of suitable on-line analytical instrumentation. In spite of the obstacles, some interesting work has been done. This paper presents a review of current industrial control strategies in ore sorting, dense media separation, gravity separation and electrical and magnetic separation.

Jan 1, 1986

By Byron Belew, Juris R. Harlamovs, D. B. Dreisinger, John L. Watson, G. A. Kordosky, Thomas O. O’Keefe

Unwanted impurities, present in raw materials, are often coextracted along with desired constituents during leaching. Due to its abundance and ease of extraction, the presence of ferric iron in leach solutions, solvent extraction circuits, and subsequently in electrowinning circuits, has always been a problem. In the case of zinc hydrometallurgical processing, iron is frequently an impurity in leach solutions. Purification of such solutions by solvent extraction, using di (2-ethylhexyl) phosphoric acid (D2EHPA) in a kerosene diluent, results in ferric ions being readily extracted along with zinc into the organic phase. Ferric iron has proven difficult to strip from the organic phase, but it is known that ferrous iron may be easily stripped from D2EHPA, and hence a process to effect reduction of iron present in the organic would have great potential. This research investigated a process to directly reduce ferric to ferrous iron in the organic phase, and to strip the ferrous iron using a dilute acid solution. The process utilized metallic zinc as the reductant and a low concentration sulfuric acid stripping solution. The results of the laboratory tests illustrated that iron could be readily removed from the organic phase by simultaneous direct reduction and acid stripping. The reductive stripping process was subsequently utilized in industry at the laboratory and pilot plant levels. The results of the industrial tests were encouraging and demonstrated the potential of this novel concept.

Jan 1, 1993

By Philip L. Hageman, Paul H. Briggs

An important tool for use in the geochemical assessment of abandoned mine-waste piles is a leach procedure that can easily be done in the field and used for on-site screening of historic mine-waste material. We have developed a simple field leach test that is an effective indicator of waste pile geochemistry and can be used in order to establish the relative geochemical fingerprint for a given pile. This simple procedure also provides indication of the potential chemical composition of run-off from the weathered surface of these piles. As part of developing the technique, a comparative study was carried out on eight mine-waste composite samples from different deposit types. Splits of all eight composites were leached using the field leach test procedure and a modified version of EPA Method 1312 (SPLP). We found that the field leach test consistently provides relative indication of leachate geochemical trends comparable to leachate data derived from the more regulated, time consuming and laborious EPA Method 13 12 (SPLP).

Jan 1, 2000

By Jerry R. Johanson

Introduction Many solids processes that look feasible on paper or even in pilot studies become disasters in full scale. Changes in solids flow characteristics from pilot scale to full scale be- cause of larger solids contact pressures, thermal shocks, or unforeseen temperature excursions often cause full-scale solids flow problems not encountered in the laboratory or pilot studies. Fortunately, proper applications of solids flow principals and solids flow properties measurement at full scale conditions can anticipate the problems and thus provide an accurate basis for full-scale design or existing plant modifications. Solids flow properties The basic solids flow property definitions are given in Table 1 (Johanson, 1966, 1976, 1978, 1985). In this section, the author will discuss each property and its potential for creating full-scale pilot plants. Unconfined yield strength The unconfined yield strength of a bulk solid determines the tendency for cohesive hangups of the solids in the process and is effected by the time at rest, chemical reactions, temperature, liquid content, solids size consist, and phase changes of solids or fluids involved in the process. One of the common mistakes is to consider the solids condition only at the beginning and the end of the process. For example, consider the direct reduction of iron ore. The feed solids are free-flowing, hard lump ore or pellets. The end result is a hard, free-flowing reduced sponge iron lump or pellet. One might conclude that the process involves free-flowing lumps. This conclusion may seem reasonable based on laboratory studies oreven pilot plant studies where solids contact pressures are very low. Unfortunately, during the reduction reactions at high temperatures, the rock or pellets soften and, with solids contact pressures associated with the full-scale plant, may fuse together, thus providing a possible solids hangup in the moving bed reactor not evident in the low pressure pilot scale. Fig. 1 shows some typical unconfined yield strength measurements for pellets as a function of solids contact pressure at various times at rest. Note at low consolidation pressures, generally associated with laboratory or pilot plant studies, the pellets show no strength unless held at rest for an extended time. This will produce a very free-flowing condition in pilot plants that will not exist in the full size reactor.

Jan 1, 1990

By W. G. Courtney

The prevention of frictional ignition with a ripper-type continuous mining machine using conical bits was investigated in the laboratory using cutter-drum-mounted water sprays. Results indicated that frictional ignition during dry cutting of sandstone with conical bits was readily obtained even at low drum rpm, while wet cutting with a carefully-designed water spray nozzle located behind the bit substantially reduced the likelihood of frictional ignition. However, the orientation and operation of the spray nozzle is critical and involves almost no margin for error. A Lee-Norse 265 ripper drum has been modified to include durable water seals and is presently being field tested underground.

Jan 1, 1987

By M. Poulton

Backpropagation, learning vector quantization, counterpropagation, functional link, probabilistic, and. self -organizing map are among the most popular neural network classification paradigms. Each paradigm finds a unique set of weights that will map the input pixels into their respective output classes. The usefulness of each network depends on its overall accuracy, ease of use, speed and scaling. The fastest and most accurate networks in this study were the functional link and counterpropagation. These networks, however, do not scale well to large input vectors or large training sets. A better choice is the LVQ network which achieves high accuracy, is fast, requires a minimum number of input parameters and presents fewer scaling problems.

Jan 1, 1992

By S. Crewdson

Vertical hoisting of materials using hoists and skips is common in the Mining Industry. These systems have a number of drawbacks, one being limited hoisting capacity at medium depths. FKC-Lake Shore and Metso Flexowell have been developing and installing vertical belts for medium depth shaft applications for many years, progressively going deeper whilst increasing belt capacity. The latest development from Metso the Pocketlift® belt advances this technology allowing higher tonnages to be lifted from greater depths. The design, manufacture, installation and operational experience of a 1818 tonnes capacity, 273 meters vertical lift Pocketlift® system at the White County Coal Pattiki 2 mine is the subject of this work.

Jan 1, 2003

By A. S. Moss, J. Linkous

Where difficult shaft sinking conditions exist, it may be appropriate to use a blind drilling technique. The success of the method is in part due to the presence of a drilling mud which fills the shaft void during excavation. The mud performs two important functions with respect to shaft stability: it reduces the influence of groundwater; and, due to the mud weight, gives a positive sup- port to the shaft walls. The application of the method is illustrated by a case history which traces the development of a shaft from the initial investigation to determine the shaft location, through the evaluation of wall stability and mud requirements, to the shaft sinking contract and actual conditions encountered.

Jan 1, 1986

By D. S. Cavers

INTRODUCTION This paper discusses aspects of rock engineering applicable to surface gold mines. Discussion particularly centers on areas in which rock mechanics can enhance the mine productivity or profit- ability. Methods of analysis are discussed briefly but for more detai1s the reader is referred to the appropriate references. A team approach to the overall design of the pit generally pro- duces a better result at an overall lower cost. In particular, money is wasted by asking for a "report on slopes" and then input- ting this slope angle into a pit design and economic analysis study without further reference to the geotechnical engineer. Pit slope angle depends on slope orientation, location, pit shape, pre-existing discontinuities and mining methods. Preliminary slope angles can be produced but optimization depends on ongoing inter- action between the mining engineers, geologists and geotechnical engineers. This interaction can a1 so substantially reduce overall design time which may be critical in bringing remote plays into production. Most surface gold mines in North America are in igneous or metamorphic environments. Rock mechanics aspects discussed in this paper will be discussed with reference to these environments al- though most of the principles and comments are applicable to sedimentary environments as we1 1.

Jan 1, 1987