Search Documents

By Austin Whillier

INTRODUCTION Use of air-cooling or refrigeration equipment in underground mines is needed when conventional ventila¬tion techniques do not maintain acceptable environ¬mental temperatures in working areas. Because refrig¬eration can be very expensive, it should be implemented only after all possible and practical steps have been taken to eliminate or reduce heat sources in the mine. As an example, to prevent the main ventilation fans from contributing heat to mine air, they should be located in the air return and not in the air intake. It is particularly important to prevent any direct contact between hot water and ventilation air, especially in mines which encounter large flows of hot fissure water. Any water hotter than the prevailing wet-bulb temperature of the ambient air must be removed by pipes located as close as possible to the water source. This hot water must not be allowed free contact with the incoming ventilation air at any time during the water's passage out of the mine. Although insulation of the pipes carrying the hot water is seldom necessary, direct contact between the air and the water must be prevented so the warm water cannot evaporate. REVIEW OF COOLING PRACTICES Spot Coolers vs. Centralized Refrigeration To eliminate a few specific hot places in an otherwise cool mine, it is possible to use devices known as "spot coolers." A typical spot cooler that uses chilled water is shown in Fig. 1. These devices consist of self-contained refrigeration units that are often mounted on rail cars for haulage to hot spots. The cooling capacities of such spot coolers usually are limited to about 100 kW or 30 "refrigeration tons." A refrigeration ton represents a cooling rate that produces 1.0 st of ice in 24 hr; that is a cooling rate of 3.517 kW (200 Btu per min). Typically, the electric-power consumption to drive the compressor motor of the refrigeration plant in mines is 1.0 kW per refrigeration ton, corresponding to a coefficient of per¬formance of about 3.5. The principal difference between spot coolers and centralized refrigeration plants is the method of re¬jecting heat from the refrigeration system. Centralized refrigeration plants always discharge heat into the reject or return airflow of the mine; often that is the primary influence in selecting the location for the underground refrigeration plant. Heat from spot coolers usually is rejected into drain water or into air that is not flowing to the location requiring the cooling. As a result, spot coolers remove heat from troublesome hot spots in the mine, injecting that heat-plus the electrical energy used by the cooling unit itself-into other working areas where the ambient conditions are cooler. In effect, this is "robbing Peter to pay Paul." In deep, extensive mines, spot coolers usually pro¬vide only temporary and, over the long term, expensive solutions to localized cooling problems. Centralized re¬frigeration plants are preferred for such mines, with cooling distributed throughout the mine as required. Fig. 2 illustrates a typical underground centralized re¬frigeration plant. Centralized plants lend themselves to improved maintenance at reduced costs while offering the economy of size. Refrigeration plants of larger unit sizes have considerably lower initial costs than smaller unit sizes. The remainder of this chapter is devoted to large refrigeration plants, with no further consideration of spot coolers. Cost of Refrigeration Total Cost: The total cost of refrigeration amounts to about $200/kW of cooling per year (1981 US $). This total cost breaks down into approximately three equal parts: 1) Financial charges, which include the interest and amortization on the capital cost of the initial installation, and the cost of necessary underground excavations. 2) Operating and maintenance costs which include the cost of the electric power to drive the refrigeration plant's compressors. 3) Distribution costs which include costs for pump¬ing, insulated piping, and air-to-water heat exchangers. The local cost of electric power, the number of operating months per year, and the method of refrigera¬tion distribution all contribute to the actual costs in¬curred in a given application. However, the variations usually are limited to no more than ±30% of the $200/ kW per year total cost figure. Cost Per Ton: Refrigeration cost per ton of mineral production can be calculated if the annual production tonnage from the refrigerated section of the mine is known. In most cases, this cost will be less than $1 .00/t. However, in deep mines with high rock temperatures, such as those found in South Africa, the total cost of refrigeration can increase to several dollars per ton of broken rock. Distribution In deep extensive mines, distributing refrigeration often accounts for about half the total cooling costs. As a result, careful consideration and planning must be

Jan 1, 1982

By N. B. Aughenbaugh

The People's Republic of China has 582 Gt (641 billion tons) of proven coal reserves. At present, 576.5 Mt (635.5 million tons) of coal are mined a year which makes China the third largest producer of coal in the world. Underground mining accounts for 95% of the total production. This paper will discuss the coal districts, coal types, jurisdiction of coal mining, and methods of underground mining. The article also will outline China's objectives in future planning and development of its coal reserves.

Jan 1, 1982

By N. Wahl, D. M. Blackketter, R. Thornton

This paper evaluated using a water-filled abandoned mine (Orphan Boy) as a heat source for a 240- kW closed-loop heat pump with the goal of heating a 2,000-m2 building. The mine has a 245-m vertical shaft connected to a large stope by three horizontal cross-cut shafts. There is 1,250 x 106 L of water at a consistent temperature of 24-26° C that is available mostly in the stope. The only heat exchanger placement option is in the vertical shaft. Therefore, the focus was to model heat exchanger placement in the vertical shaft to determine the extent to which the systems will induce thermal currents between the stope and vertical shaft. Modeling of thermal currents, temperature profiles and heat contribution from the ground was done using finite difference and computational fluid dynamics. An optimal configuration was determined showing sufficient water movement and heat transfer will occur with a low water temperature in the shaft above 20° C. This project supports a U.S. Department of Energy (DOE) grant that will implement the full-scale system.

Jan 1, 2013

By Richard E. Otoo, Evan J. Owen, Virginia T. McLemore

Disruption in critical minerals supply chains has resulted in the evaluation of various types of mineral deposits for critical minerals potential. Much of the study on critical minerals focuses on occurrence and characterization, but little research has addressed what concentrations of critical minerals in a mineral deposit are required to make an exploration target into an operating mine. Understanding the cut-off grades of ore deposits being actively mined is one criterion to determine if concentrations in an exploration target are high enough. Cut-off grade is defined as the minimum amount of mineral contained in a ton of ore that is sent to the processing plant. Among many factors, cut-off grade depends upon the size and type of the deposit and mining operation, the processing technique, and market prices. This research does not aim to define cut-offs for determining if a mineral deposit is economic. Rather, it defines estimates of concentrations of critical minerals that could be considered good enough for further exploration. For example, ~2% total rare earth oxide (TREO) is the cut-off grade for Mt. Pass carbonatite, but 500 ppm TREO could be an exploration target for coals.

Feb 1, 2025

By Neil D. Donnell, O&apos

Ore reserve estimation at the Syncrude Canada Ltd. open-pit oil sands mine in Northern Alberta has evolved since the project's inception. Early techniques followed a conventional petroleum reservoir analysis format, with relatively widely-spaced drill holes and semiquantitative grade data. Experience has developed a more standard mining approach, including classification of geological materials by both lithology and sedimentary origin, timely and multi-purpose drill holes, precise analytical data, empirical recovery factors, a computerized geological data base, and an ore body block model. Future efforts will involve enhancement of existing techniques, use of geostatistical algorithms, quantification of confidence limits, and improved control of the ore model by geological parameters.

Jan 1, 1985

The following is a summary of some of the companies that were exhibiting their products and services at MINExpo INTERNATIONAL 2000. Atlas Copco develops, manufactures and markets rock drilling tools, tunneling and mining equipment, and surface and geotechnical drilling equipment. The company provides a line of drilling products, including production drilling rigs, rock reinforcement bolts and rock drills. Atlas Copco’s Boomer is a series of high-capacity drill rigs that provides economy, production capacity and reliability

Jan 1, 2000

By R. Guardia, J. Hoskins, E. Claros, Y. Kamiya, R. Ramirez, J. Dalenz, P. Fernandez, E. Ilgren

Crocidolite is a well known causative agent for mesothelioma. Studies have shown that the pathogenicity of the fiber from different mines varies considerably and it has been postulated the parameter that appears most likely to account for this variation is fiber width. Epidemiological studies have shown that ‘thin’ fibers from mining areas of Western Australia and the Cape Province, in South Africa are associated with a high mesothelioma risk while exposure to ‘thick’ asbestiform amphibole fiber of the same fiber type are associated with little or no mesothelioma risk. This study is concerned with ‘thick’ Bolivian crocidolite but similar findings also probably explain the paucity of mesotheliomas in the Finnish anthophyllite, South African amosite and African Transvaal crocidolite mines. The findings from the present study suggest the incidence of mesothelioma in the three major cities of Bolivia is not significantly elevated above background even though Bolivian crocidolite has been used for the past 60 years commercially and residentially in all three cities. Although some cases of mesothelioma may have been missed due to a failure to reach hospital or a shortened natural lifespan, mesothelioma generally occurs after the age of 50, we cannot tell precisely the extent to which these were confounding. We suggest the most likely explanation for the lack of mesotheliomas despite the large populations at risk from the long and extensive residential and commercial use of crocidolite containing products, is related to an increased fiber width distribution and a concomitant reduction in the ‘Stanton fiber size’ fraction.

Jan 1, 2012

By J. A. Delgadillo, C. A. Pérez-Alonso

"Tumbling mills using balls as grinding media are used extensively in the mining and cement industries to produce fine powders; however, it is well known that the process of size reduction is highly energy-intensive. For this reason, much of today’s comminution research is aimed at understanding grinding mechanisms, by estimating power draft and modeling milling circuits using the discrete element method (DEM). DEM predicts individual particle trajectories, the distribution of energy and contact forces at each collision, lifter wear and power draw. This paper presents a prediction of the discharge particle size distribution using three components, mass balance model (sometimes referred to as a population balance model, PBM), impact energy distribution of the mill obtained from the simulation of the charge motion using DEM and breakage characteristics of particles determined from drop-ball tests. DEM simulation of the charge of a tumbling mill was done using the code MinProSim 1.0 to obtain impact spectra at different operative conditions. Then, the population balance model (PBM), based on impact energy distribution, was used to predict the final particle size distribution in a batch mill and compared with experimental data. It is demonstrated that the DEM-PBM approach allows a reliable solution to predict particle size distribution for tumbling mills. Ideally, the model has to predict size distribution for any operational condition and feed characteristic; however, it has been shown that predictions include some degree of error.IntroductionThe discrete element method (DEM) has recently become a powerful numerical tool that can be used to investigate internal mill charge in ball mills. The early work of Cundall and Strack (1979) used DEM to analyze soil as a discrete medium. Later, the method was improved to simulate the operation of tumbling mills and optimize the design in order to increase the efficiency of energy utilization. Also, it is of great interest to relate ore breakage based on impact energy spectra obtained by DEM simulations and the breakage distribution function used in the PBM to predict particle size distribution in tumbling mills.King and Borgeous (1993) broke single particles in an ultra fast impact load cell to compute the phenomenological parameters in a microscopically more detailed population balance model. Kapur et al. (1997) simulated the size spectra of progeny particles produced by impact grinding as a function of the impact energy. Narayanan (1987), Narayanan and Whiten (1988) and Lira and Kavetsky (1990) estimated the energy-dependent breakage distribution function for scaleup and modeling of industrial ball mills."

Jan 1, 2015

By S. R. Dindarloo

"Truck-shovel systems are the dominant material loading and haulage machinery in open pit mining operations. Optimal selection, sizing, and allocation of this capital intensive equipment is highly desirable for both achieving production targets and improving the mine’s economics. In this study, discrete event simulation technique was applied for modeling material transportation in Golegohar open pit iron ore mine in Iran. Direct observation of the material loading and haulage for duration of three months resulted in statistical modeling of the operation in the form of probability distribution functions. These probability models were used as the inputs of a stochastic simulation model constructed in GPSS/H simulation language. The model was validated through comparison with the actual operation and was used to test different what-if scenarios and sensitivity analysis of the current system. Some modifications in the number of trucks, shovels, and dispatching strategies were proposed. Simulation resulted in considerable improvements in the mine’s production and economics.INTRODUCTION There are three different mechanisms of discrete, continues, and hybrid material transportation in open mines, including but not limited to: i) in-pit crusher and conveyor belts (hybrid), ii) slurry piping (continues) and iii) truck-shovel system (discrete). Although, each mechanism has its advantages, the truck-shovel system is the dominant method of material loading and handling in open pit mines owing to its high production rate, excellent flexibility, relatively low operating and capital costs, and good maintainability. General objectives of optimal equipment selection include: i) meeting the long and short term requirements of production rates, ii) human & equipment safety, iii) environmental protection, and iv) economic operations (Figure 1).The two most important decision factors on a truck-shovel system selection and sizing are the equipment geometry and size. Geometry (equipment width, weight, turning radius, swing angle, etc.) is mostly controlled by mine’s designs and layouts, as well, as operational constraints. After selection of a favorable geometry based on the constraints; the next step is to select the equipment manufacturer. Once the geometry and manufacturers are selected; the next step is to decide on models (e.g. Bucket size) and required number of each unit"

Jan 1, 2015

By Jr. Moulton

Extractions of minerals from Searles Lake brines have taken place since 1873. Early operations were for borax and raw trona found on the surface, expanded after 1914 to include potash, salt cake, and soda ash. A new soda ash plant now in operation will double area production. The evaporite beds were formed by desiccation of Eastern Sierra runoff. The resulting series of brine-bearing salt beds supply the fluids necessary to feed the area chemical plants. Production methods include evaporation and crystallization for potash, borax, and salt cake; carbonation of brine to recover soda ash; and organic extraction of borax.

Jan 1, 1980

By L. Yan, D. Yantek

Federal regulations require refuge alternatives in underground coal mines to sustain life for 96 h while maintaining an apparent temperature below 35 °C (95 °F). Research by the U.S. National Institute for Occupational Safety and Health (NIOSH) has shown that heat and humidity buildup is a major concern with refuge alternatives because they have limited ability to dissipate heat, and high internal air temperature and relative humidity (RH) may expose occupants to heat stress. The heat transfer process within and surrounding a refuge alternative is complex and not easily defined, analytically or experimentally. To investigate heat and humidity buildup in refuge alternatives, NIOSH conducted multiple in-mine, 96-h tests on a 10-person tent-type refuge alternative, a 23-person tent-type refuge alternative and a six-person metal-type refuge alternative. The results show that when moisture was introduced to represent perspiration and respiration from miners (wet tests), the average temperature at midheight increased by 10.5 °C (18.9 °F) and the RH approached 88 percent for the 10-person tent-type refuge alternative; the average temperature at midheight increased by 9.4 °C (16.9 °F) and the RH approached 94 percent for the 23-person tent-type refuge alternative; and the average temperature at midheight increased by 7.7 °C (13.9 °F) and the RH approached 95 percent for the sixperson metal-type refuge alternative. For the dry tests, where no moisture was introduced, the average internal temperature increased by 12.6 °C (22.7 °F) for the 10-person tent-type refuge alternative, by 10.3 °C (18.5 °F) for the 23-person tent-type refuge alternative and by 8.4 °C (15.1 °F) for the six-person metal-type refuge alternative. These results may provide refuge alternative manufacturers and mine operators with guidelines and considerations for evaluating temperature profiles for portable refuge alternatives. The information may then be used to make decisions on occupancy ratings and heat mitigation strategies based on the thermal environment in which the refuge alternatives will be installed.

Jan 10, 2018

By Harry M. Conger

Thirty years ago, the U.S. gold mining industry was hanging on by its fingernails. Save for one great mine, the Homestake, most production was coming from copper smelters such as Kennecott and Magma. Even Homestake itself was under great pressure from rising costs and a fixed price for gold. The outlook was dim, to say the least. Today, as it has for most of the past decade, the American gold mining industry stands among the world leaders in production, and in the development of mining and mineral processing technology. What caused this dramatic change? Obviously, the freeing of the gold price was a major factor, as was the decline in South African production, but these events alone could not have created the U.S. strength we see today. It was technology, investment, and the determination of miners to build an entirely new industry that were the indispensable ingredients. The U.S. Bureau of Mines, with great foresight, had begun the research that led to heap leaching before the gold price began to rise, and Newmont had committed to build a small mill at Carlin, a move then considered quite risky. From that point, the U.S. gold mining industry was placed on lower-grade ores then being found in Nevada and elsewhere, but it was soon apparent that we would have to develop new technologies to deal with more refractory ores, carbonaceous as well as sulfide-bearing. This is now being done with considerable success. Despite its success, or perhaps because of it, the gold mining industry has come under pressure from various groups who characterize their activities as motivated by "public interest." The public interest they refer to properly include the health and safety workers and impacted communities, as well as protection of the environment, and with these concerns we miners have relatively little argument. In fact, we consider health, safety and the environment among our highest priorities, and not just because regulations may require us to do so. The argument, however, is not about the regulation of a viable mining industry, it is about a well-organized movement to attack and condemn mining in the media and to misrepresent its importance to the Nation and its willingness to accept responsible regulation. Once largely local or regional, the interest groups to which I refer are now quite large, national in scope, and even becoming international. This trend, taken together with finances raised from their dues and contributions, would make the interest groups formidable adversaries for mining, but their grip on the media enormously magnifies their influence. Unfortunately, it also makes possible the wide dissemination of incomplete, incorrect or slanted information. I am not here to "bash" the interest groups. On the whole, I believe that many of them have made positive contributions to society. As conservationists, however, I question their authority to make, or foster, decisions about which American industries and communities live and which die. To illustrate, I would like to present for your consideration the problem of cyanide, one of the issues over which the gold mining industry is most threatened. CYANIDE-POISON OR MIRACLE SOLVENT? Let me get this out of the way right up front: cyanide in most of its chemical forms is toxic. In some forms it is also listed as a carcinogen. These are adverse characteristics cyanide shares with a considerable number of industrial chemicals, including some that are widely used without the stringent regulations already in place for the mining uses of cyanide. In these uses, by the way, the risk to humans comes from direct ingestion of cyanide or cyanide-bearing solutions, or from the accidental acidification of solutions leading to release of hydrocyanic acid gas. That these risks are under control in mining can be seen from the fact that, in modern U.S. practice, there has never been a documented fatality attributed to cyanide! Because of its toxicity, cyanide cannot enter and be accumulated in the food chain. It can, however, be a threat to birds and animals that ingest cyanide-bearing solutions. Protection against this is, quite properly, a responsibility of individual mining operations, and considerable sums are spent each year to prevent or reduce bird and animal exposures. It should be evident, though, that many human activities, including highway traffic, windmills, use of pesticides and the like, result in bird and animal losses. Mining's use of cyanide, and the measures taken to protect birds and animals, should be considered in context. Cyanide must be kept out of surface streams and groundwater, and existing regulations mandate this. Any cyanide residues left in leach heaps, waste dumps and disused facilities must be eliminated, and we have proven technologies to do this now, just as we have means to detoxify tailings prior to disposal. The gold mining industry decries those rare instances when irresponsible operators fail to deal with contamination, and agrees that they should be held responsible. We do not agree, however, that the great majority of responsible companies should be punished, in advance, for accidents that have never happened. So much for the poison, what about the "miracle solvent?" Is that an overstatement? Well, consider the fact that gold has been called "noble" from earliest times, because it does not oxidize under atmospheric exposure, and that it appeared to the ancients to be utterly insoluble. Later generations of scientists did discover that it could be dissolved, but only by a combination of acids so potent that it became known as aqua Regia. Later still, it was found that chlorine would also dissolve gold, and attempts were made to base commercial processes on this, without a great deal of success. It remained

Jan 1, 1995

By O. Ditsele

Coal plays an important role in the energy needs of the World. Given its wide abundance and low cost, coal use is bound to increase with the growing energy demand. Despite its importance, there are growing concerns over coal?s environmental burdens, especially its contribution to greenhouse gas emissions. To ensure sustainable extraction and use of coal, opportunities for minimizing potential impacts from coal have to be identified and exploited. Whilst extensive work has been done on life cycle assessment of coal use, especially in electricity generation which uses the bulk of coal produced, there has been limited work focusing specifically on coal mining. This study aims to estimate the cradle-to-gate life cycle climate change impacts of coal from a surface coal mine in the United States. The study employs general principles of ISO standards for LCA.

Jan 1, 2010

By E. F. Draskovich

In 1984 a high temperature heat recuperation system was installed in the pellet plant of the National Steel Pellet Company located in Keewatin, Minnesota. The system is similar to those of Cleveland Cliffs Empire and U.S. Steel's Minntac operations. It recovers hot process air from the cooler by induced flow, and directs it to an intermediate zone between the drying and preheat zones on the grate machine. This system recently underwent further modifications in April 1985, following initial operation in 1984. The M. A. Hanna Company, which manages the property, developed the design criteria and made the subsequent recommendations for modification through its research facility in Nashwauk, Minnesota.

Jan 1, 1986

By P. A. Hendricks

The surface coal mining industry in the United States employs over 50,000 people and is responsible for 60% of domestic coal production. This represents a very significant contribution to our national economy and an important source of highly skilled and well paying jobs. The U.S. Bureau of Mines (USBM) has targeted surface mining as an important research priority to reduce the social and economic costs associated with surface mining injuries and fatalities. USBM safety research focuses on the development of technologies that can enhance productivity and reduce mining costs through a reduction in the number and severity of mining accidents. This report summarizes a number of completed and ongoing research programs that address a broad range of surface mining safety problems. Research methods are described, and research products which are suitable for industry implementation are highlighted.

Jan 1, 1994

By J. Kretschmann, K. Sakamornsnguan

"Sustainable development is an influential ethical concept in modern mining management. However, the concept is not culturally neutral because it is based on Christian, Western values. These values can be very different from traditional values in emerging mining countries like Thailand, where Buddhist values are dominant. When applying the concept of sustainable development, these differences should be taken into account. Different values imply different interpretations of ‘good mining’. They have a significant impact on how mining operations are evaluated, perceived, operated and managed. This paper attempts to integrate Buddhist principles with approaches of the sustainable development concept. When local values are appreciated and maintained, mining companies and their external stakeholders can identify objectives and approaches that match with their own values and contexts. Practices based on this integrated ethic can help to promote sustainable mining and to minimize communication risks for enterprises in mining countries like Thailand. INTRODUCTION The objective of this paper is to integrate Buddhist principles to the application of sustainable development concept to mining activities. The structure of this paper is divided into four parts. An introduction provides basic information about Thailand, its mining industry and the role of Buddhism on the past development. The second part compares the differences between the sustainable mining framework and the implications of Buddhist principles on mining. In the third part, the core Buddhist teachings are integrated into the sustainable mining framework. This is followed by conclusions in the last part. THAILAND, BUDDHISM, AND MINING Thailand is a constitutional monarchy state in Southeastern Asia with a population size of around 65 million [1]. Its GDP in 2013 was 391 billion USD [2], predominantly deriving from manufacturing (38%), trade, transport and communication (24%), agriculture (8%) and mining and construction (4%). Still the largest part of the Thai workforce (39%) is working in the agricultural sector. The remaining part of the workforce is equally distributed across services, manufacturing, and mining and construction sectors. [3]"

Jan 1, 2015

By Steven I. Olson

Since the introduction of froth flotation, the Florida Phosphate Industry has faced the challenge of coarse particle -850 +425µm (-20 +35 Tyler mesh) beneficiation. Several techniques have been used to upgrade this difficult size range. This paper discusses one approach that has met with success; namely, improved fractional recoveries through enhanced areation and improved material transport characteristics via larger than standard flotation cell mechanisms.

Jan 1, 1981

By A. B. Cecala

Enclosed cabs have been used for many years to isolate workers on mobile equipment in the mining industry for health and safety reasons. These enclosed cabs create a microenvironment for workers where they can be either more protected or more vulnerable to contaminants. Over the past decade, the National Institute for Occupational Safety and Health (NIOSH) has performed substantial research efforts to improve the air quality inside enclosed cabs of both underground and surface mobile mining equipment. In these efforts, NIOSH has partnered with mining companies, original equipment manufacturers (OEMs), and manufacturers of filtrations and pressurizations systems in a synergistic effort to reduce respirable dust and improve the air quality inside these enclosed cabs. Various field studies over this time have shown an array of results ranging from very minor to very significant reductions (protection factor: 3 ? 89) in respirable dust levels inside these enclosed cabs. In addition to and concurrent to the field work, NIOSH also performed a comprehensive laboratory study to evaluate all the factors involved in cab filtration and pressurization systems and identified those factors that were most significant for an effective system. From this comprehensive research effort, the key components for an effective filtration and pressurization system have been identified in an effort to provide the best air quality, thus minimizing the respirable dust exposure, to equipment operators inside of enclosed cabs of mobile mining equipment.

Feb 27, 2013

By Peter L. Comanor

At Getchell, Nevada a thousand tons per day mill for extracting gold from an ore containing orpiment and realgar was operated several years until early 1967. A cyanide process with a roaster was used in the processing of the ore. Mill wastes were contained in tailings ponds, in which the concentration of arsenic, currently, is one per cent or higher, Studies were conducted determining the effect of the tailing wastes on the Upper Sonoran vegetation of the area. Grid and line-intercept techniques were employed to obtain botanical informatics of the area surrounding the tailings ponds. Data of the per cent ground cover, species frequency, and plant vitality as a function of distance from the tailings ponds was collected. The data was compared to other botanical data collected from a control site outside the influence of the tailings ponds. In an attempt to isolate naturally occurring factors for varying plant communities from hose induced by factors derived from the close proximity of the tailings, soil cores were taken along the line-intercepts at intervals of 30 meters. The cores were analyzed for several compounds and elements needed for growth, or known to inhibit growth. Specific physical parameters of the soil samples were also taken. The paper describes the impact made by mill wastes containing large amounts of arsenic on the Upper Sonoran vegetation of the Getchell region. Described in detail are the techniques used to make the correlations between the plant communities and the influences of mill wastes.

Jan 1, 1974

By Gabino Preciado, Louis Sandbak

Corrosion has long been identified as a potential risk to the long-term ground support stability due to degradation of internal ground support elements such as rock bolts but also to surface support from mesh, straps, bolt plates, and ancillary support of utilities such as hangers. The emphasis is to understand the corrosion mechanisms on the primary ground support elements and any supplemental steel or arch sets. The water and chemical processes from oxidation(rust), stress corrosion cracking, and even the electrical charge created during these reactions contribute to the corrosion of the steel support elements. The main goals are to mitigate the effects of corrosion and to be able to predict those areas of high water or high sulphide for potential rehab maps. It is also essential to identify and classify the visible corrosion as part of damage mapping and provide bolt testing to those areas of suspected internal damage from corrosion. This is important to get an estimate of the support longevity or expected life before rehab to minimize the overall cost of the operation.

Feb 1, 2024