Search Documents

By E. W. Hawk

he power generation industry may be required to reduce carbon dioxide (C02) emissions if regulations related to global climate change are enacted. Coal-fired generation emits more than 80% of the power sector CO2 and would be a likely target for CO2 reductions. Compliance with the Kyoto Protocol will require a 33% reduction from the projected year 2012 emission level, even with moderate load growth. This article describes an analysis of power industry CO2 reduction options and their costs. It assesses how a generator would make compliance decisions under a mandatory CO2 emissions reduction program. Carbon sequestration, fuel switching and new plant construction are considered. The Global Climate Change Treaty signed at the Rio de Janiero Earth Summit in June 1992 set the long-term goal of stabilizing CO2 concentration in the atmosphere. The December 1997 Kyoto Protocol established short-term mandatory targets for the United States and 37 other developed countries. The United States' target is a 7% decrease by 2012 from the 1990 "greenhouse gas" level. Developing countries are exempted from reductions, according to the Kyoto Protocol, despite projections that indicate a significant increase in their emission levels. The Kyoto Protocol must be ratified by the US Senate. US power industry carbon emissions were 490 Mt (540 million st) in 1990 and are projected to be 680 Mt (749 million st) in 2012, according to the US Energy Information Administration. Coal-fired generation emits more than 80% of the power sector CO2. Assuming that the power industry is only required to reduce emissions by a proportional share, a 33% emission reduction, or 225 Mt (248 million st) of carbon, would be required to comply with

Jan 1, 1999

By Deepak Malhotra

Comminution circuits in general account for fifty percent of capital and operating costs for a processing plant. Significant advances have been made in optimization of these circuits. One would expect a few circuits to be the favored designs for plants. Review of grinding circuits worldwide indicates that a variety of circuit designs are utilized for non-technical reasons. A brief review of circuits and reasons for their selection is given in this paper.

Jan 1, 1998

By T. Stuczynski

In the past ten years about 3000 wastewater treatment plants have been built in Poland. The result of this development has been a massive increase in overall sludge production. According to data supplied by the Ministry of Environmental Protection, 400,000 dry tons of sludge are generated every year in Poland (Koblak-Kalinska 1996). Still it is difficult to estimate the amount of sludge, which is used in agriculture or for reclamation purposes. However, it can be assumed that this comes to no more than 10 percent of all sludge produced in Poland on a yearly basis. Thus it became obvious that an urgent solution to this problem was needed. Local authorities in Silesia realized in the early 90?s that a demonstration was necessary to encourage the proper utilization of sludge. This was the basis for establishing the Biosolids Subpart of the Silesia Project, which addressed the use of biosolids in the reclamation of mining and smelting dumps (Stuczynski et al. 1996). Metal waste sites themselves are known to contain more than 87 million tons of waste (Pistelok et al. 1995). Each year this amount increases by approximately 400,000 tons. We realized that a simple solution for stabilizing these sites would be to cover them with vegetation in order to reduce leaching of toxic elements, as well as to keep metallic fugitive dust from entering the environment. The reclamation of smelter waste sites, which was carried out within the framework of the Silesia Project was a joint effort of local government, industry and international research institutions/agencies, including the US Environmental Protection Agency (EPA), the Center for Research and Control of the Environment (OBIKS), Virginia Polytechnic Institute and IUNG. One of the goals was to evaluate the possibility of adapting the rules of sludge management currently used in the United States to conditions commonly found here in industrial regions of Poland. However, the main objective of the Silesia Project was the development of guidelines concerning all aspects of sludge use for the reclamation of degraded lands and waste sites. Biological aspects related to reclamation of metal waste with the use of biosolids will be discussed in this paper.

Jan 1, 2002

By Debbie Nakamura, Daniel Tempelis, John E. Shamma

The Metropolitan Water District of Southern California established a Board of Consultants to assist them in administering the design and construction of the Inland Feeder Program tunnels. The Board acts as an expert review body for the owner, looking at key issues that can potentially impact the success of the program. The use of the Board evolved over the life of the project, and its composition was modified to better address the needs of the owner, and the Program requirements. The experience, function, and value of such a board is analyzed and discussed in this paper.

Jan 1, 2003

By James McMaster

The Kamyr Countercurrent Tower Leaching Process is intended to combine, in a single tower, thickening, leaching, separation and clarification of pregnant solution, and washing of leaching chemicals from the tailing pulp. For a gold or silver metallurgical plant, the flowsheet would consist of crushing and grinding, cyclones for size control and partial thickening, the Kamyr tower, and a gold or silver recovery system of either carbon in solution, zinc precipitation, or direct electrowinning. Ancillary systems for the Kamyr metallurgical plant would include cyanide preparation, fiber preparation and recovery, and flocculant preparation.

Jan 1, 1990

Dunn has written an excellent paper providing a wealth of advice on what is often the most costly consumable in the mineral processing plant. As he pointed out, grinding media selection and quality control can play a major role in successful plant operation. Owing to the economic importance of this topic, there are some important factors related to media sizing that I believe merit further comment. Dunn made reference to a slightly simplified version of the Azzaroni (1981) equation and pointed out its successful use for the Henderson SAG and Climax ball mills.

Jan 1, 1991

By E. Jannoulakis

This paper introduces a practical methodology for analyzing vi¬bration records in view of improv¬ing blast designs and preempting anomalous vibrations. This technique, which is based on empirical data, uses a blasting-efficiency determinator (BED) as an indicator of vibration-energy transmission. The method was tested using data from a blasting event at an open-cast coal mine in the province of New Brunswick, Canada. The results derived from the BED values showed that geology and delay timing were probably the principal factors that induced high-intensity vibration propagation.

Jan 1, 2000

By Ed L. Schrader

Kaolin of the Georgia-south Carolina "Clay Belt" are used in a wide variety of filler and extender applications. Sane applications specifically require the performance enhancement delivered by incorporating kaolin into the product formulations. Other applications are less specific in requirements for an inert mineral filler. In order to be a feasible candidate for filling and extending, a mineral or mineral product must be generally inert (except where specific interaction with the filled medium is desired), inexpensive, easily handled and transported in a variety of forms, accessible to a broad segment of the desired market, and must exist in sufficiently large ore reserves as to assure production for many years. Of course, more precise requirements are necessary in specific applications of a prospective filler material.

Jan 1, 1985

Diesel Particulate Matter (DPM) is considered carcinogenic after prolonged exposure. With increasing use of diesel-powered mining equipment in underground mines, miner?s exposure to DPM has been increasing. Most studies on the issue has been DPM control measures with few studies on diesel exhaust propagation patterns after leaving the tailpipes. This study uses computational fluid dynamics (CFD) to investigate the airflow pattern in an underground metal/nonmetal mine for a single heading. Several high DPM concentration areas are identified in the study and common practices for compliance are suggested. Airflow and DPM distribution are compared between blowing and exhausting face ventilation systems. Suggestions are also provided for the protection of miners in the face area.

Jan 1, 2009

Fluorspar was not mined in the United States during 2004, although a small amount of usable synthetic fluorspar (CaF2) was produced from industrial waste streams. The majority of fluorspar consumed in the United States came from imports or stockpiled material purchased from the National Defense Stockpile (NDS). In addition, consumption is supplemented by use of by-product fluorosilicic acid produced at phosphoric acid plants. In 2004, annual production of fluorosilicic acid was 50kt (55,000 st) or about 88 kt (97,000 st) of 92 percent fluorspar equivalent. In 2004, annual production of fluorosilicic acid was 50kt (55,000 st) or about 88 kt (97,000 st) of 92 percent fluorspar equivalent.

Jan 1, 2005

By P. R. Khangoankar, S. Devasahayam

An experimental study of the particle charac¬teristics of the magnesium carbonate crystals formed by the reaction between magnesium chloride and sodium bicarbon¬ate at different temperatures is described. The rate of growth of magnesium carbonate crystals for any constant tempera¬ture is established, and this rate of growth is related to the degree of supersaturation at the given temperature. The activation energy calculated using empirical constants de¬rived from the relationship between the crystal growth rate and supersaturation, is indicative of a surface-reaction mechanism.

Jan 1, 1996

By T. van Sandwijk, G. Van Weert, E. Molleman

This paper reports on test work that explored the dissolution/precipitation reaction: ZnS + 2HCl - ZnC12 + H2S, which is part of a process used in the production of pure ZnS. The research focused on the influence of proton activity on the dissolution of zinc concentrates obtained from the Brunswick Mine No. 12 in Canada (Brunswick Mining & Smelting); the Red Dog deposit in Alaska (Cominco Ltd.); and the Tara deposit in Ireland (Outukumpu Zinc). A comparison between the results of the experimental dissolution as a function of pH and the dissolution predicted by thermodynamics suggest that the three concentrates contained sig¬nificant amounts of the more reactive mineral wurtzite, although XRD analysis showed mainly the presence of the mineral sphalerite.

Jan 1, 1999

By F. Leschhorn

A computer model for long-term production scheduling is presented. By combination of different operations research algorithms it has been possible to design a system which is able to solve difficult long-term planning problems. The practical application of the model by a west-german hard coal mine is shown. It is proven that the EDP-model provides substantial support to the planning engineer by solving complex optimization problems.

Jan 1, 1989

By Bruce Kennedy, Dan Nilsson

Mining means drilling and blasting in order to break down the rock, loading and transport, and often also crushing the ore down to a suitable size. These operations can be done in open pits or in underground mines, and also, to a lesser extent, in marine mining. The same operations are also used in various types of construction, i.e., for roads, water power stations, etc. Before beginning a detailed economic analysis of the factors which enter into deciding whether to mine by open-pit or underground mining, and at what point a change should be made from open-pit to underground mining, or vice versa, it is of interest to consider some general factors.

Jan 1, 1982

By C. J. Burkhalter, H. Andrade, T. C. A. Gardner, J. P. Campbell

During the 1990’s several copper heap leach facilities treating crushed and agglomerated oxide and sulfide ore were constructed in South America. The majority of these facilities have been in operation for at least three years, during which time the operators have been able to monitor the performance of the heaps. The basis for the paper is a compilation of these operators’ experiences, leading to a discussion of the lessons learned over the past decade. Several key geotechnical issues are examined, focusing upon the integrity of the ore, drainage material and pipe network, along with the success of any inter-lift liners.

Jan 1, 2002

By John S. F. Dunlop

One of the more difficult problems frequently facing geologists and mining engineers is that of estimating the ore reserves of mineral deposits. Cost conscious mining operations invariably require an accurate knowledge of tonnage and grade for both short and long term planning. A case study is presented, showing how a classical frequency distribution was fitted to a population of drillhole assays. Using these results, a grade- tonnage curve is derived using the Lasky expressions, and the results discussed. A geostatistical analysis is then presented. First, variograms are drawn, models fitted to them and analyses made of drift and anisotropy. Second, simple block kriging is carried out and the results plotted on large 1000 scale plans, suitable for overlay with routine .mine plans. Kriging results are verified using two independent techniques: random kriging on a regular grid and inverse distance weighting. Finally an attempt is made to optimize the drilling grid, and to fully tabulate the total computer running costs for the work described.

Jan 1, 1979

By J. D. Miller

Flotation chemists have long sought to unravel the mechanisms of carboxylate collector adsorption by semi-soluble salt minerals. In particular, the adsorption density of adsorbed carboxylates, adsorption kinetics, speciation (chemisorbed, physisorbed), orientation, and conformation are of interest. Given the importance of these phenomena in establishing the hydrophobic state at a mineral surface, in-situ surface spectroscopy studies certainly are justified. Such measurements traditionally have been difficult to perform. However, beginning in the late 1980s, a Fourier transform infrared (FTIR) spectroscopic technique was developed that has allowed for the acquisition of a wealth of detailed information concerning carboxyiate adsorption in semi-soluble salt flotation systems. The technique, internal rejection spectroscopy using single-crystal internal reflection elements, is reviewed, as it applies to semi-soluble salt flotation systems.

Jan 1, 1999

By S. Dinescu

The paper deals with the modeling of longwall shearer cutterhead interaction with the coal, in order to study the influence of different limiting factors of the haulage speed, and the cutting regime ensuring optimal energy consumption A computer simulation model is used to draw-up the torque vs haulage speed and the haulage force vs haulage speed dependence diagrams, for different strength of coal and different degrees of bit wear.

Jan 1, 2008

By M. J. Scoble

There is no straightforward and systematic method for adequately measuring blast damage in on-going mining operations. This paper considers various techniques available for the measurement of blast damage, making particular reference to recent underground hardrock mine studies. This paper concludes by indicating the importance of understanding and accounting for geology and emphasizes the need for a robust damage-audit procedure.

Jan 1, 1997

By M. Paventi, M. J. Scoble, B. B. Mohanty

There is no straightforward and systematic method for adequately measuring blast damage in on-going mining operations. This paper considers various techniques available for the measurement of blast damage, making particular reference to recent underground hardrock mine studies. This paper concludes by indicating the importance of understanding and accounting for geology and emphasizes the need for a robust damage-audit procedure.

Jan 1, 1998