Search Documents

By G. Roy, C. B. Pettersson, S. Nandagiri, D. J. Ivor-Smith

The Coastal Water Authority's 2,740mm/2,590mm (108 in./102 in.) pipeline, known as the Northwest Lateral Project, will transport raw water from an existing pipeline over 14.3 km (8.9 miles) to the City of Houston's East Water Purification Plant. The new pipeline crosses under Houston Ship Channel and Greens Bayou in tunnels at approximately 30.5m (100 feet) and 25.9m (85 feet) depths, which present unique experiences in tunneling under open bodies of water in the Gulf Coast's soft ground conditions. An earth pressure balance TBM is being used for the deep tunnel sections where the ground demonstrates high overload factors and variable conditions ranging from clays to silty sands. This paper discusses the design approach for the tunnels and shafts, ground conditions, constructability, and selection of the primary lining system.

Jan 1, 1989

By G. Barelli, C. Giusti, W. H. Langer

Natural aggregate – sand, gravel, and crushed stone – is the number one non-energy mineral resource in the world in terms of both volume and value. A plan for the sustainable development of aggregate resources can include: 1) policies and economic incentives to encourage identification and protection of potential resources, 2)efficient quarrying and processing of aggregate, 3) efficient use of primary aggregates, 4) greater use of recycled, waste, or substitute material, 5) inclusion of costs of all environmental impacts in price of material, 6) reclamation to beneficial secondary uses, and 7)identification of objectives, targets, actions, and sustainability indicators. Quarrying can also contribute to sustainable ecosystems through natural habitat reclamation.

Jan 1, 2003

By D. A. Norrgran, J. N. Orlich

Described is the application of high- intensity magnetic separation throughout the spectrum of industrial minerals. Performed either wet or dry, the separation has application in both the recovery and concentration of value minerals and in removing deleterious mineral constituents. The various types of magnetic separators along with the design and operating parameters relative to separation response are characterized. The characteristics of specific minerals to magnetic collection and the production of high-grade concentrates are described. Laboratory, pilot-scale, and plant studies carried out on a variety of industrial minerals have demonstrated the effectiveness of magnetic separation as either a primary or a secondary unit operation to achieve product quality.

Jan 1, 1987

Changes have been made in the Bulletin, Section I., for this month ; Personal and Employment columns have been added, and a Forum, in which will be included letters and discussions of general interest to members of the Institute ; live news and new matter have been inserted near the front; lists of officers and committees are placed next to the technical section, while standing matter and other information which is interesting chiefly when sought for, has been segregated as much as possible. Members are urged to co-operate with the Editor by sending in news items of themselves and others, and by giving some of their spare time to this department each month.

Jan 4, 1913

By REHMAN ATTA UR, Kwame Awuah-Offei

This work evaluated the effects of bucket orientation and operating parameters on resistive forces and penetration for rubber-tire loaders (RTLs), such as load-haul-dumps (LHDs) and front-end loaders (FELs). The work used a 1:16 scale LHD model to test an RTL bucket operating at different levels of traction (tractive effort), speed, digging height and rake angles in a full factorial design experiment. The test was repeated on two muck piles with different particle sizes, and generalized regression modeling was applied to test the association of rake angle, tractive effort, speed and digging height on penetration and resistive forces for RTL buckets. The results show that speed and tractive effort are more important in explaining RTL penetration and resistive forces than height above the floor and rake angle. Speed, tractive effort and height above the floor are positively correlated to bucket penetration, whereas the rake angle is negatively correlated to penetration. Similarly, speed, tractive effort, rake angle and height above the floor are all positively correlated to resistive forces incurred during initial penetration. The results show that the combined effect of speed and tractive effort is negatively correlated to penetration and resistive forces — a novel finding that enhances our understanding of RTL loading. The results also show that the effects of speed, tractive effort and height above the floor all change with changes in particle sizes. This work provides insights into the effects of rake angle, height above the floor, tractive effort and speed on penetration and resistive forces for RTLs to facilitate better design and efficient use of these loaders.

By Lawrence K. Nordell

Historical methods of designing steel cord belt splices are compared with modern finite element modeling (FEM) methods. Dependence of the belt strength rating on the splice dynamic fatigue strengths is reviewed. A number of splice schematics are examined, using simple spring theory and FEM methods. Steel cord wire rope design is discussed. The importance of the insulation gum rubber properties and their splice dimensional factors and tolerances are analyzed. Splice fatigue lie analysis procedure is reviewed. This may be used to predict splice life or time of failure, depending on how the conveyor belt is operated.

Jan 1, 1993

By Nigel Fung, J. D. Humphrey, R. H. Oats, J. H. Ingle

Production dozing of cast material is a cost effective method of improving dragline or mobile equipment overburden removal. Yet dozer productivity is reduced during the part of the process that requires the dozers to cut material away from the highwall. One solution is to use a hydraulic excavator to remove this material and throw it into a windrow for the dozers. By freeing up the dozers for more productive work the overall system productivity increases 25% and cost per yard is reduced by up to 10%. Dozer fleet sizing can be determined to match a specific production schedule or can be sized to balance with an excavator’s production.

Jan 1, 2004

By LUKAS FAHLE, JURGEN F. BRUNE, ANDREW J. PETRUSKA, ELIZABETH A. HOLLEY, Gabriel Walton

Adverse ground behavior events, such as convergence and ground falls, pose critical risks to underground mine safety and productivity. Today, monitoring of such failures is primarily conducted using legacy techniques with low spatial and temporal resolution while exposing workers to hazardous environments. This study assesses the potential of novel simultaneous localization and mapping (SLAM)-based light detection and ranging (lidar) data quality for rapid, digital and, eventually, autonomous minewide underground geotechnical monitoring. We derive a comprehensive suite of quality metrics based on tests in two underground mines for two state-of-the-art mobile laser scanning (MLS) systems. Our results provide evidence that SLAM-based MLS systems provide data of the quality required to detect geotechnically relevant changes while being significantly more efficient for large mine layouts when compared to traditional static systems. Additionally, we show that SLAM-specific processing can achieve an order of magnitude better relative accuracy relevant for change detection than quality metrics derived from traditionally deployed tests would suggest, while reducing SLAM-drift error by up to 90 percent. In collaboration with an operating block-caving mine, we confirm these capabilities in field tests on a minewide scale and, for the first time, demonstrate methods of rockfall detection using MLS data. While more work is required to investigate optimal collection, processing and utilization of MLS data, we demonstrate its potential to become an effective and widely applicable data source for rapid, accurate and comprehensive geotechnical inspections.

Jan 1, 2023

By C. H. Sampaio

The effectiveness of modem spirals in the processing of fines from Brazilian coals is assessed and discussed. Coals representing the four major coalfields in Brazil have been cleaned in Reichert LD 9 spirals in pilot and industrial plants and performance results are here presented. Normalized distribution curves for all equipment and splitters are presented and were modeled using an empirical model. These data have been compared with those for shaking tables and water-only cyclones (WOC), and it has been observed that, in the size interval investigated, spirals have indeed superior accuracy than WOC and comparative performance to tables. By analyzing experimental as well as simulation results it could be observed that although limited by the poor liberation characteristics of most Brazilian coals, significant ash and sulfur removal could be achieved using spirals.

Jan 1, 1995

By James W. Cooksley

This report concerns a seismic geophysical exploration program which was conducted 3 miles southeast of the Carlin Mine, in Lander County, about 18 miles north of Carlin, Nevada. A twelve-fold reflection seismic line was executed over a one-mile traverse in section 32, Township 35 North, Range 51 East. This study is part of an exploration pro- gram directed toward finding Carlin-type gold deposits which are concealed under younger alluvium and volcanics. The exploration objectives of this program are as follows: 1) measure the thickness of the younger, sedimentary and volcanic deposits which overlie the "productive rock sequence", 2) delineate the Roberts Mountains thrust fault, 3) investigate the origin of the geochemical anomalies present in the western portion of section 32.

Jan 1, 1985

By John D. Nelson

Unprotected uranium mill tailings impoundments can pose a significant risk to nearby inhabitants and the surrounding environment in the event of a prolonged or catastrophic release of contaminants contained in the tailings. As a result of this potential, reclamation plans for such facilities must include engineering designs to protect against disruption of the tailings and the potential release of radioactive materials. The goals for such engineering designs should be to provide overall site stability for long-term periods with no need for planned ongoing maintenance and to provide a repository for the tailings that will not place a burden on future generations. Although the goal is to provide a maintenance-free system that does not require monitoring, it must be recognized that some period of surveillance would be reasonable. The surveillance period could be relatively short and only needs to assure with reasonable confidence that the reclamation scheme that was implemented is functioning adequately. An investigation was conducted by Nelson, Volpe, Wardwell, Schumm and Staub (1983) entitled Design Considerations for Long-Term Stabilization of Uranium Mill Tailings Impoundments (NUREG/CR-3397). This report assesses the degree of confidence with which long-term reclamation plans can be expected to remain effective over specific periods of time, and to assess the additional effort required to extend the design period from one long-term period to a longer one. This paper presents a summary of that investigation and discusses some of the important conclusions.

Jan 1, 1984

By Ellis G. Goree, George A. Simmons, Andrew B. Pervis

The pneumatic classifiers are widely used for fine dry powders separation These classifiers can be used for either the removal of fines from coarse feeds or the removal of coarse particles from ultrafine feed To optimize the operation of pneumatic classifiers, a thorough understanding of the impact of operational parameters on the efficiency of classification is essential This paper describes the design features and effects of operational parameters followed by illustrations of pneumatic classifiers usage in two case studies

Jan 1, 1983

By Earl Sackett

In its 110-year history as a mining camp, the Boleo copper district of Baja California has weathered significant changes in its operation, ownership, and profitability, despite an inhospitable environment and unique ore body. For some 65 years, under the operation of Compagnie Boleo, the area ranked as the second largest copper producing district in Mexico, with over 560 km of underground workings. As its ore grade-and profitability-declined, operations continued sporadically and with varying degrees of success. Today, operations at Boleo are maintained -despite the economics -while work is underway to devise a viable metallurgical process. Lab tests on a hydrometallurgical method look encouraging and, though this may end the district's days as a mining camp, the feasibility of the process may result in an 18-kt/d full-scale operation.

Jan 7, 1980

By N. Oswald

As coal mines age and become more developed, ventilation modeling becomes more important for the planning and continued operation of the system. Numerous studies have been performed and presented that address the collection of data and measurement of airway friction factor and resistance per unit length values. However, a quantitative analysis of the resistance for stoppings in coal mines for different construction materials and methodologies has not been adequately addressed. In order to develop an accurate/realistic ventilation model both airway resistances and stopping resistance values need to be determined. Over the course of the past two decades Mine Ventilation Services, Inc (MVS) has measured the resistance of stoppings of various construction types in mines throughout the world. An analysis of this data is presented in this paper along with a discussion of measurement methodology.

Jan 1, 2009

By W. G. Pariseau

Recent advances in rock-mass mechanics and computational technology now allow for the stability analysis of excavations in "wet" mines where mining-induced changes in rock mass deformation and fluid flow are coupled and time dependent. In addition to water pressure and flow in jointed, possibly porous, rock masses, all of the usual dry-mine parameters, including the premining stress state and rock-mass properties, are taken into account. Finite-element analyses of shafts and tunnels, as circular, elliptical, rectangular and arched-rectangular hole shapes excavated in an initially stressed and pressurized rock mass, indicate that the usual guidelines for optimum shape and orientation of single openings apply. Here, optimum means maximizing the minimum wall safety factor or, equivalently, minimizing the peak stress concentration. The results also show that failure originates in elements at the wall and the minimum safety factor at the wall in the wet case is always less than the dry case, regardless of drainage time allowed.

Jan 1, 1997

By George W. Luxbacher

The inclusion of a new term "planned subsidence" in the Surface Mining and Reclamation Act of 1977 has lead the U.S. coal mining industry into a new aspect of engineering: subsidence planning. Subsidence planning has necessitated the integration of geotechnical, civil, and mining engineering disciplines. Although much of the foundation and application work has been completed, subsidence planning is still a developing area. This paper discusses the application of subsidence planning in several brief case studies (a high voltage transmission tower, a sewage treatment plant, and a slurry impoundment), emphasizing the risk assessment aspects necessary to account for some of the uncertainties that may exist.

Jan 1, 1986

By G. E. S. Valadão

This paper is concerned with studying the dewatering behavior of three samples of iron ore products. The objective is to improve the industrial filtration performance by taking into account the laboratory results. Mineral samples came from the Iron Ore Quadrangle in the state of Minas Gerais, Brazil. These samples represent products from the industrial processing of hematitic ores. The samples have almost the same chemical and mineralogical compositions, but they have different size distributions and different specific surface areas. The filtration tests were performed using a modified Büchner funnel apparatus. The results indicate that size distribution and specific surface area have significant influences on dewatering behavior. For Sample 1, the addition of flocculant and/or surfactant was not essential to improving filtration performance. For Sample 3, the cake porosity and the cake thickness were influenced by the addition of the flocculant. On the other hand, the simultaneous addition of flocculant/surfactant decreased the cake formation time and reduced the cake moisture. For Samples 2 and 3, it was also observed that the industrial operation could be improved by taking into account these laboratory results. Key words: Dewatering, Iron ore, Hematite, Filtration, Flocculation, Surfactant

Jan 1, 2003

By Dean J. Soderstrom

Soil and sands were contaminated with depleted uranium from weapons testing. This resulted in the formation of a complex mixture of uranium compounds. Characterization studies of the soil indicated the uranium was present as uranium metal, uranium oxides, silicon-bearing metallic uranium, and uranium silicates. A process was developed to selectively remove dense uranium compounds using gravity separation and a chemical extraction system to remove uranium which was not available for separation by gravity methods. Results from characterization studies and pilot scale testing are presented for background information. The primary purpose of this presentation is the report of the results achieved in the field application of the processes.

Jan 1, 1995

By 000-000-604

HISTORIACAL INTRODUCTION Mineral processing has three principle branches, to quote Taggart, "Ore Dressing, which comprises the methods of separation of solids in inorganic crude by means which do not affect substantial chemical change; Extractive Metallurgy, which utilizes chemical reactions for separations of constituents from solids in inorganic crude; and, Fuel Technology, which employs both physical and chemical methods for separating and rearrangement of liquid gaseous and solid components in crude oil and natural gas, tar sands, shale oil, or coal." The scope of this handbook covers the first two classifications, that is, "ore dressing" and "extractive metallurgy," which have been combined in one term: "mineral processing." For a brief history of the development of mineral processing, one could well refer to the Introduction, Sec. I of the Handbook of Mineral Dressing by Taggart, Froth Flotation, Principles of Mineral Dressing by Gaudin, and the original Richard's Ore Dressing, volume No. 1, first published in 1903-1905. In these references and the references given in them a coverage of the history of "ore dressing" can be found and studied at the reader's leisure. For the history of extractive metallurgy as well as ore dressing, the bibliography in General References, taken from a History of Ex¬tractive Metallurgy by F. Habashi, will give a good background for those who are interested in more detail on the history of metallurgy in general. Mineral processing covers a very wide field as is illustrated by the topics discussed in Part II of this handbook and dates back to the early history of man which started with the production and use of native minerals such as gold, silver, copper, mercury, and meteoric iron which were washed or picked from deposits on the surface of the earth and worked because of their malleability. Later, melting was discovered and then it was possible to cast objects of these metals, excluding mercury. The discovery of a method for reducing the metal¬lic oxide probably was developed from melting fragments of oxides or roasted sulfides with charcoal, so that the native metal could be produced in simple blast furnaces such as are used today in rural parts of Spain, China, and elsewhere. Eventually, it was learned that iron could be readily worked when hot, which resulted in its replacing bronze for tools, weapons, and cutlery. Carbon dating and correlation with the Brittle Cone pine has

Jan 1, 1985

By H. N. McLeod, M. J. Thom

The use of cyanide in gold mining requires the careful handling and storage of cyanide rich tailings. Cyanide in groundwater can frequently be both persistent and mobile, so that tailings basins need to be designed to limit and collect seepage. Assessment of the potential environmental impact requires an understanding of the hydrogeologic regime, both before, during and after mining. Groundwater monitoring wells provide a basis for monitoring tailings pond behaviour and for assessing the impact of mitigative measures to reduce or control seepage. A case example of Cheni Gold Mines Lawyers Project in Canada is presented to illustrate the use of groundwater monitoring to determine the amount of cyanide degradation and attenuation between the tailings pond and the receiving environment.

Jan 1, 1991