Search Documents

By T. M. Barton, M. Gauna, A. A. Campoli

Coal mine bumps, the violent failures of overstressed coal, present a safety hazard to miners when longwall mining is conducted in deep, bump-prone coal mines. Two different longwall gate entry systems were evaluated in a southern Appalachian coal mine located in the Pocahontas No. 3 coalbed under approximately 610 m (2000 ft) of overburden that included a massive sandstone member. Both gate entry systems employed a center abutment pillar flanked by yield pillars. The original design used a 24.4-m (80 ft) square abutment pillar, while the new design employed a 36.6-m x 54.9-m (120 ft x 180 ft) abutment pillar. Rock mechanics instrumentation data analysis and in-mine observations indicated that this increase in abutment pillar size significantly decreased bump potential. The new design in worst-case conditions increased effective bearing area 62%, with only a 9% increase in gate entry system width, and eliminated face bumps that were experienced with the original gate entry design.

Jan 1, 1993

By Martin Oatman, Lawrence Lenahan

The West Seattle Tunnel is part of a regional sewer conveyance system located in Seattle Washington. The tunnel was constructed for the Waste Water Treatment Division of the King County Department Of Natural Resources, from June of 1995 through the first quarter of 1997. The Geologic setting for this soft-ground tunnel consists of glacial, interglacial, glacio-lacustrine, and alluvial soils. This paper, prepared jointly by the owner and con-tractor, will describe project-related site geology, engineering considerations, construction, and dispute resolution/avoidance practices.

Jan 1, 1997

By T. M. Ruff, W. G. McCoy, M. J. Beus, S. Iverson

Monitoring conveyance position and wire rope load directly from the skip or cage top offers several significant safety and production advantages. The Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) developed a shaft conveyance monitoring system (SCMS). This system consists of position and guide-displacement sensors, a maintenance-free battery power supply and a new sensor, which is mounted on the wire rope with a Crosby Clip, to measure hoist-rope tension. A radio data link transmits sensor output to the hoistroom. A state-of-the-art automated hoisting test facility was also constructed to test the concept in a controlled laboratory setting. Field tests in full-size shafts are now underway.

Jan 1, 2000

By Mark Gershon

This paper describes a linear programming (LP) application that schedules mining operations in an optimal manner. The model is developed such that it can be applied to a broad spectrum of mining activities. While linear programming has been applied to mine scheduling in the past, the models have been either site-specific or they have only optimized one aspect of mine operations without regard to others. The Mine Scheduling Optimization (MSO) concept makes use of a mathematical model to: (1) Determine the optimal operation of a mine, from mine to plant to market. (2) Account for mine-plant-market interfaces. (3) Optimize operations over the life of the mine. (4) Accomplish long, intermediate, and short range planning.

Jan 1, 1982

By M. L. W. Tuttle, B. R. Berger

Our study focuses on the geology, hydrology, and geochemistry of a variety of molybdenum (Mo) porphyry systems. The systems are either high fluorine, granite, Climax-type, systems (e.g. Mount Emmons/Redwell Mo deposit, Colorado and Questa Mo deposit, New Mexico) or low fluorine granodiorite systems (e.g. Buckingham Stockwork Mo deposit, Battle Mountain, Nevada and Cannivan Gulch Mo deposit, Montana). The water quality of streams, natural springs, mine discharge, and ground water from drill holes were assessed in the region of these deposits. The ultimate goal of our study is to understand the environ-mental behavior of these Mo porphyry systems in the context of geologic setting, hydrologic regime, and climate.

Jan 1, 2004

By Y. Wang

China is a big mining country with a long mining tradition and history. At present, there are nearly 200,000 different mines and 21 million workers. The total production value of mining makes up 6% of GNP. With the development of economy, the mining industry has played a more important role in our economic market, supplying more than 95% non-reusable energy, 85% of industrial and agricultural raw materials, over 75% of fertilizers and 30% industrial and agricultural water.

Jan 1, 2001

By Suresh K. Bhatt

Appalachian coalfields have been the predominant source of quality coals since the inception of commercial mining in the United States. In a broad sense, Appalachian coalfields can be considered those east of the Mississippi River, representing about 55% of total US coal production. In this special feature on Appalachia in MINING ENGINEERING, emphasis is given to the four coal-producing states of Pennsylvania, West Virginia, Virginia and (eastern) Kentucky. These four states produce more than 90% of the coal from the total Appalachian region, or about 40% of the total US coal production. Historically, Appalachia has been the principal source of coal for domestic industries and for export. There have been numerous fluctuations in the Appalachian coal industry during the past 20 years. Appalachia was affected by cyclical and structural changes in various industries, particularly the US steel industry, and changing world coal markets. It was also the region of more mine worker labor stoppages than other parts of the country. In general, the factors that affected Appalachian coal production over time are identical to those that determined changes in coal production nationally.

Jan 1, 1995

By Joginder S. Bhore, Francis M. Keville, David E. Puza, Roger C. Borggaard

A portion of the Massachusetts Bay Transportation Authority's Red Line Extension through Somerville, Massachusetts consists of 1,553cm (5,092 LF) of hard rock tunneling 6.7m (22 ft.) diameter horeshoe, 148m (485 LF) of mixed face tunneling, 7.2m (23 ft.) diameter circular, beneath an active railroad in a heavily commercialized business district. This paper will deal with the excavation of the mixed face area without the use of a shield. It will address the special excavation and support problems encountered during tunneling operations using the floating crown bar and modified spiling methods. Topics covered will include excavation and support methods, cement grouting, compaction grouting, and instrumentation. PROJECT DESCRIPTION The Davis Square to Porter Square Tunnels and Shafts Somerville/ Cambridge, Massachusetts is part of the Massachusetts Bay Transportation Authority's (MBTA) 5.1km (17,000 ft.) Red Line Extension. This extension runs from Harvard Square, Cambridge, to Alewife Brook Parkway, Cambridge through Somerville. This portion (MBTA Contract #091-106) required the excavation and concreting of 1,701m (5,580 LF) of single track twin tunnels consisting of 1,553m (5,092 LF) of conventional hard rock tunneling under 56 residential properties and 148m (485 LF) of mixed face tunneling beneath an active railroad in a heavily commercialized business district. The mined diameter of the mixed face tunnel is 7.16m (23.5 ft.) Access to the tunnel was via the Summer Street vent shaft, and the two Grove Street access shafts where all tunnel excavated materials were removed.

Jan 1, 1981

By Robert C. Dunne, Maurice E. Freeman, Denis S. Yan

A laboratory tower mill was used to investigate the effect of some variables on the power requirements of a plant mill. The grinding laws were tested for fine grinding and Charles' law and Rittinger's law found to be most closely satisfy the experimental data. The effects of ball size, ball charge mass and media type were investigated. The screw speed was altered to control the power input as required. The results indicate that changes in these variables will change the grinding kinetics but in terms of the grinding efficiency they have no effect on the size-energy relationship. The main factor in the specific energy efficiency is the transfer of the input energy to the charge by variation of the agitation mechanism. The efficiency of a tumbling ball mill and a pin stirred mill were tested for comparison.

Jan 1, 1995

By R. L. Keaton

Since the earliest days of mining, the job of digging coal out of the earth has been considered one of the world?s most dangerous occupations. From 1880 to 1910, mine explosions and other accidents claimed thousands of victims. In 1907 alone, over three thousand deaths occurred in U.S. coal mines. Public concern has prompted the passage of much needed safety legislation; from the creation of the U.S. Bureau of Mines in 1910, to the comprehensive laws of the Federal Mine Safety and Health Act of 1977. This type of legislation, along with the cooperation of industry, labor, and MSHA has contributed greatly in making mining safer and more healthful. Mining deaths and injuries have declined Significantly since those early days. However, even though this trend is positive, none of US can afford to look at the injury numbers and frequency rates and label them as acceptable.

Jan 1, 1988

By J. Y. Kim, R. W. Stanley, L. Rosato

Silver contained in zinc calcines undergoes several phase changes as it proceeds through the leaching circuit of a roast-leach-electrowin zinc plant. In this study, the flotation response of silver, from leach residues prepared under a variety of carefully controlled operating conditions in the pilot plant has been examined. Flotation of neutral leach residue is shown to be technically viable and to merit consideration for those plants without a high-acid leach circuit, but having significant silver values in the feed. Residue leach conditions must be kept slightly acidic to promote the formation of Ag2S, (AgCu) 2S and Ag2S rims on residual unroasted sphalerite, while simultaneously avoiding the hydrolysis of soluble iron, which depresses silver recovery and grade. Factors to be considered during integration of a flotation process into an electrolytic zinc plant are discussed.

Jan 1, 1992

By Q. Xu

The new process consists of the selective coalescence of fine hematite particles by fine magnetite. The gangue minerals are dispersed by some dispersant; thus it can be separated by desliming. This process is particularly suitable for fine-grained hematite/magnetite-type deposits.

Jan 1, 1989

By Fathi Habashi

IT APPEARS that the phenomenon of ion exchange by which saline water was converted to sweet was known to Moses and Aristotle. However, the credit for the recognition of this process is generally attributed to Thompson (1850) and Way (1850), who reported that when a soil was treated with either ammonium sulfate or ammonium carbonate solution, most of the ammonia was adsorbed and calcium was released. It was later proved by Eichorn (1858) that the adsorption of ions from ground waters by clay constituents was a reversible process. The first attempts to utilize ion exchange phenomena was in the field of water softening around 1906, using natural and synthetic silicates. In 1935 Adams and Holmes in England observed that crushed phonograph records (phenol-formaldehyde and amine-formaldehyde resins) were capable of exchanging ions.

Jan 1, 1970

By J. P. Savely, D. E. Nicholas, R. D. Call

Slope stability is a probabilistic phenomenon and as such should be analyzed with probabilistic methods. Fracture orientations alone, insufficiently model the rock mass. Other parameters describing the fracture set characteristics are required with distributions that can be sampled to fit mathematical stability models. Important considerations are length, spacing, dip, waviness angle, and overlap. These parameters are of major concern in design and are difficult to measure. Reasonable estimates of the characteristics can be used to provide distributions.

Jan 1, 1977

By M. C. Baumann

The Getchell Mine is located in Humboldt County, Nevada, approximately 70 km northeast of Winnemucca. Slope management has been a critical factor in the feasibility of mining operations since they began in the early 1930's. Although underground entries began in 1937, underground production was limited because hanging walls consisting of clay gouge and crushed rock tended to collapse into the workings. Controlling these collapses required extensive timbering. Due to these poor ground conditions, surface open-pit mining was the primary mode of production from 1938 to 1967 with only minor contributions from underground operations. Mining was suspended in 1967 due to economic pressures. From 1960 to 1967, the previous operator mined the property in three open pits. Initially, these pits were constructed with footwall benches, but these failed. These failures were aggravated by construction of 60° slopes in footwalls with shale partings dipping into the pit at 43° to 60°, resulting in large planar failures and wedge failures. In response, the previous operator adopted a slope parallel to the bedding planes.

Jan 1, 1993

By Thomas G. Hayes

Track-type tractors remain one of the most cost-efficient stripping tools available to coal miners. Whether they are "sweetening up" a dragline operation with prebenching or serving as the primary tool, dozers are important in driving down mining costs. This article reviews the application zone of track-type dozers. It also provides suggestions for site setup, equipping tractors and machine operation. In recent years, the track-type tractor has become more of a production tool in mining. With the advent of bigger machines, bulldozers have become a typical component in mining operations, removing overburden down to the top seam of coal. Large tractors can also be teamed up with draglines and other systems to maximize the effectiveness of the mining system. Bulldozers remain the tool of choice for topsoil removal, spoil reclamation or any application that demands low ground pressure, or short distance. The introduction of the 523-kW (700-hp) track-type tractor to the mining industry has made the bulldozer a low-cost-per-ton means of removing overburden. The large tractors offer enough productive capability to be considered prime stripping tools. And they can lower mining costs by complementing other mining systems (dragline, cast blasting and loader/truck). Four criteria determine whether a track-type tractor is the right machine for a particular application: ? Production requirements - dozer may fit job requirements better than a second dragline. [ ] ? Product support - availability of parts, service and technical expertise. ? Labor situation - how much of the cost per ton goes to the operator. ? Resale opportunity - recover a percentage of capital cost. Mining efficiency is economically controlling the cost of any system. Most operations rate the most economical means of moving material as cast blasting, dragline and the track-type tractor. All three of these systems share one common value: They are all sensitive to distance. Regardless of the application, all mining systems have an economic range. Exceeding this distance will affect cost and productivity.

Jan 1, 1997

By Jack K. Lemley

This paper will provide an update of the Channel Tunnel Project including a discussion of the overall legal structure and management organisation. It is important to understand the mission that TML, as a design/build contractor, has undertaken and how the various interfaces have evolved between the other entities involved in the project. The paper will describe the evolution of the management organisation and the approach to completion of our contract, recapping the historic events and moving into a projection of how we will manage the completion of this very large transportation system.

Jan 1, 1991

By A. Arik

The accurate estimation of mining-block grades continues to be a challenging task for ore reserve practitioners. The estimation method used and the variability of the mineralization in the deposit are two factors that affect the accuracy of the estimates. The objectives of this study are to determine how different estimation methods perform on a given deposit and to determine the impact that the nature of the mineralization has on the results. A comparison of several estimation methods for prediction accuracy is performed based on conditional simulation results.

Jan 1, 2002

By Gábor Antal, József Bõhm, Barnabás Csõke

From the waste material of the production of aluminium foil aluminium pigment is produced for the paint industry by grinding it in white spirit. During grinding 1-2 % iron impurity gets into the product, weakening its quality, from the wear of the mill armour and the grinding bodies and from the contamination of the raw material. For deironing the product, a stage-operated electrically induced magnetic filter separator was developed and put into operation. The separator was sited in an explosive environment and therefore required a special design and safety system. The paper describes the results of the development work. the device that was developed, the safety system as well as the results of and experiences with the operation of the separator.

Jan 1, 1995

By S. Chander

Neutralization of acidity by addition of alkaline materials is a commonly used method to treat acid mine drainage. However, this procedure requires large amounts of reagents based on acid-base accounting. The potential use of organic additives in preventing or ameliorating acid mine drainage was investigated in this research. The tests were conducted in weathering columns using refuse samples from a coal cleaning plant. Both cationic and anionic compounds were tested. For a comparison, tests were made in the presence of limestone and lime. The results show that some of the reagents substantially retarded the rate of oxidation whereas others even enhanced it. The suppression of the rate of pyrite oxidation was ascribed to surface chelation. Formation of surface compounds prevented the pyrite particles from further oxidation. Such a treatment required only small quantities of reagents since the reaction was confined to the surface.

Jan 1, 1992