Search Documents

By R. L. Schmidt, Williamson. T. N.

INTRODUCTION This paper describes one of several research projects funded by the Advanced Research Projects Agency to extend the technology of rapid underground excavation. This study and field research effort are to investigate alternative means to determine rock and geological conditions in advance of a tunnel boring machine (TBM). Approximately 1 year of a planned 3-year program has resulted in the definition of three candidate drill systems. Hardware has been assembled to field test these candidates and testing has begun. The 3-year objective is to develop a single optimum prototype drill and test it in an active TBM operation. ACKNOWLEDGMENT This research was supported by the Advanced Research Projects Agency (ARPA) of the Department of Defense and was monitored by the Bureau of Mines under Contract No. H0210037. The authors and sponsoring agencies are indebted to the quarry operators in California, Virginia, and West Virginia who offered assistance including access to their properties.

Jan 1, 1997

By William Petruk

Performance assessments are carried out to monitor operations, to evaluate performance and to identify processing problems. The assessment involves collecting and analyzing representative samples from critical points in a flowsheet and interpreting the data. Sample analysis techniques include chemical analyses, mineralogical investigations, mineralogical analyses, and materials balancing. Chemical analyses provide the lowest cost assessment and should be used liberally, particularly in monitoring a process. Materials balances performed on chemical assays for a suite of samples are used as a first step in evaluating a process. Mineralogical investigations are more expensive than chemical analyses but need to be used only at the beginning of mining and metallurgical operations and as a second step in assessing processing problems. Quantitative mineralogical analyses combined with materials balancing provide the most complete performance assessment, but the procedure is expensive. On the other hand, the assessment has the potential of a large payback when carried out where warranted.

Jan 1, 1991

By Jeff Salai

The CP-3A contract is the final segment of the MWWST’s 28.3 km (17.6 mile)pressurized water supply tunnel for the metropolitan Boston area. The 1,288 m (4,226 feet) of U-shaped tunnel alignment passed through five rock zones employing four different primary support systems. The short tunnel began in Weston, Massachusetts, at Shaft 5A in soft, completely weathered argillite, passed through a fault zone, and ended in Dedham granite. An 18-foot diameter horseshoe starter tunnel was built to accommodate a 4.94 m (16-foot 2 1 / 2 inch) diameter Robbins TBM. Heavy water inflows were anticipated and subsequently encountered during probe drilling. Pre-excavation grouting was implemented at high pressures to displace high water inflows in the starter tunnel and consolidate the fault zone. This paper will provide an overview of the tunnel construction with an emphasis on ground control, grouting and survey control.

Jan 1, 2001

By Robert J. Auber, Thomas R. Scotese

The West Leg Interceptor is part of a new sanitary sewer system in the southwest suburbs of Cleveland. The first two construction contracts were excavated in glacial soils varying from hard tills to pressurized silts and flowing sands. These soil and groundwater conditions were locally problematic during shaft and tunnel excavations and final lining construction. A variety of solutions were developed primarily during construction. During the WLI-1R Contract, subgrade pressures, continued ground losses, and displacements necessitated extra eductor wells and modified inverts for stabilization of shafts. At the WLI-2Contract, one shaft excavation in similar ground required only one extra well. In the WLI-1R tunnel, localized inflows of groundwater, silt, and sand through the geotextile fabric were stopped by cement grouting. In one WLI-2 connector tunnel, damage to the TBM flood doors combined with wet, flowing silt and sand led to ground losses, surface settlements, plugging, patching, and chemical grouting. The concrete lining in the main WLI-2 tunnel required remedial work to improve watertightness at joints.

Jan 1, 1999

By G. Raspa

This article describes a procedure for calculating the recoverable reserves of stratified orebodies characterised by a thin and irregular layers. An application on the phosphate deposits in the N'Zeto region of the Popular Republic of Angola is also described. The procedure consists in building a block model of the deposit through the conditioned multivarial geostatistical simulation of small areal units. The recoverable reserves are then calculated and defined by applying to the model a selection processes based on measured geological/economic parameters taken from the drillholes: thickness of overburden and mineralised layers, economic grain-size fraction, grade. The procedure also takes account both of the geometrical constraints of the mining method and dilution. For reasons of confidentiality, a multiplier has been applied to the values adopted for the sampling data.

Jan 1, 1992

By Shibo Zheng, Zhengxing Gu, Zhizhong Gao

In recent years, beneficiation tests were conducted on high dolomite phosphate samples from Florida by the authors from China Lianyungang Design and Research Institute (CLDRI). The research results indicated that flotation is the most effective process for recovering phosphate from Florida high dolomitic pebble. Other operations like scrubbing, desliming and selective grinding might work to some extent, but they could only be applied as supplementary approaches in some cases. Heavy media separation and calcination-digestion technologies are hard to produce satisfactory performance. This paper presents the results of both lab scale and pilot plant tests on Florida high dolomite phosphate pebble using the fine particle flotation technology developed by CLDRI. Some discussions are made on the concerns of Florida phosphate industry and further research.

Jan 1, 2002

By Stefan Gerl, Werner Stahl

Steam pressure filtration combines mechanical and thermal processes in one filtration device. Steam condensation at the cold layers of the filter cake, build a condensation front, which even removes the capillary water from the porous filter cake. Depending on the choice of parameters it is possible to achieve a very low residual moisture content. The influence of the parameters on the dewatering results was systematically examined on a bench-scale apparatus. This paper explains the physical fundamentals, the influence of the cake dewatering parameters, and one possible method of applying the process to a disk filter device as well.

Jan 1, 1995

By Terry A. Ring

Sand bed filters are used to remove large and small particles from liquid streams. The large particles are removed by the straining action of the filter bed and the small particles are removed by particle deposition on the surface of the bed particles. Particle deposition, while being essential for the filtering action of colloidal particles, is not the only process that occurs in the filter bed. Other processes that occur are (1) the substrate becomes filled with particles limiting further deposition, and (2) some deposited particles are resuspended. The sum total of all these processes determine the performance of a filter bed.

Jan 1, 1982

By T. F. Torries

The primary criteria used by the mining industry to judge the merit of a project is internal rate of return (IRR) rather than net present value (NPV), although NPV is favored by academicians. This paper discusses the problems of IRR and NPV and compares the multigoal nature of the decision¬makers and their need for informa¬tion having the characteristics of NPV and IRR. The conclusions reached are that both NPV and IRR can be used for investment ranking, that NPV suffers the same multiple root problem as does IRR, and the use of conventional incremental IRR to reach NPV¬consistent project ranking is mis¬leading.

Jan 1, 1999

By John F. Abel

Convergence measurement across the 17.4 m (57ft) high shaft station/loading pocket at Mt. Taylor provided continuing verification of stability and safety. Three levels of instrumentation, consisting of three lines each, were installed and monitored. The instrumentation showed that the flexible lining restrained the adjacent rock. The flexible lining consisted of pea gravel with neat cement between rock and liner plate, wooden crush blocks between liner plate and steel ring beams. The loading pocket is elliptical, 11.6 by 9.6 m (38 by 31 1/2 ft) I.D. The crush blocks were designed to allow 15 cm (6 in.) of convergence. Maximum predicted convergence was 7.0 cm (2 3/4 in.) and 5.7 cm (2 1/4 in.) was measured. Convergence measurements also demonstrated decreasing deformation with respect to elapsed time and distance from the measurement station to the temporary bottom of the shaft excavation.

Jan 1, 1984

By Otto Braach, Wolfgang Frietzsche, Erdogan Gürkan

The Westerschelde Tunnel is located in the south of the Netherlands and links the two parts of the Provinces of Zeeland, Zeeuws-Vlaanderen and Zuid-Beveland, which are separated by the Westerschelde. Road traf?c has up till now taken the detour via Belgium or crossed by ferry. This unsatisfactory transport link signifies major economic disadvantages above all for Zeeuws-Vlaanderen. The first fixed link for road traffic between the communities of Terneuzen and Borsele are to be created by means of the two 6.6 km long tunnel tubes down to 65 m below sea level.

Jan 1, 2003

By J. Derwin King, Harrison R. Cooper

Applications of nuclear magnetic resonance (NMR) offer possibilities for on-line sensing of the concentrations of several elements in flowing sample streams. In addition to hydrogen, these elements, generally of low-order atomic number, include aluminum, phosphorus, fluorine, sodium, boron, and lithium contained in minerals having commercial importance. Many such elements have been difficult or impossible to successfully measure on-line using the more familiar X-ray fluorescence and neutron activation analysis techniques. The availability of practical on-stream analysis methods is essential to applying advanced controls to processes incorporating these elements. On-stream NMR instrumentation has been demonstrated in the past for several process applications including, as an example, coal flow and analysis; and the technology has recently been extended to the measurement of phosphorous BPL in Florida beneficiation plants. The technique involves simultaneous sensing of proton (hydrogen) and 31P intensities to provide data for continuous calculation of BPL in the phosphate through calibration to volume fractions of water and solids. Initial operating results are described using the PhospholyzerTM on-stream phosphorous analyzer designed for plant application.

Jan 1, 1990

By Aldino Campos, Frederico Carvalho Dias, Pedro Madureira, Patrícia Conceição, José Gomes-Pereira, Inês Tojeira, Andreia Afonso, António Calado, Luísa Pinto Ribeiro

Since 2008, the Portuguese Task Group for the Extension of the Continental Shelf has been operating the ROV "Luso" (rated for 6000m depth) for geological sampling of the deep North Atlantic seabed, performing surveys on, e.g., seamounts and hydrothermal vent fields. Amongst other sensors, the ROV is equipped with a full HD video camera with which still images of the deep ocean floor are recorded. Fixed on the ROV’s frame are two underwater "line" lasers, each generating a sharp green line (532nm) over the seabed. The two lasers are paralleled and calibrated at a set distance. Provided that the camera’s angle of view is known, numerical values for seabed surface area may be calculated using direct measurements taken from the pictures containing the laser lines. We present the corresponding main mathematical formulas, which are derived from simple geometrical considerations, and discuss how to generalize these results for an arbitrary camera tilt or pan. We present an example of application of our method by estimating values for percent coverage of rock substrate versus sediment. Our results are also relevant for determining seabed polymetallic nodule abundances from still images obtained during ROV surveys.

Sep 1, 2014

By R. L. Grayson, T. L. Dickinson, C. G. Anderson

Sponsored by the EPA, USGS, DOE, and NSF through the Committee on Earth Resources, the National Research Council’s Committee on Material Flows Accounting of Natural Resources, Products, and Residuals, created in August 2002, studied the value that material flows accounting, which can track the flow of a material from the time it is extracted to its ultimate disposal, may provide for making better integrated economic, social, and environmental policy decisions. This could be a crucial technology for the mining industry to incorporate. This paper will recount the statement of tasks, the study process, and the science-based conclusions and recommendations reached.

Jan 1, 2004

By O. E. Etheridge Jr., R. A. Lowe, C. I. Basilio, J. M. Randolph, S. W. Sheppard

The low-shear viscosity of kaolin slurries is one of the principal characteristics that determine whether a clay can be utilized for paper and ceramic applications. In this work, the causes of high low-shear viscosity and methods for improving the rheological behavior of the slurries were investigated. The presence of fine-grained smectite impurities within the kaolin was shown to detrimentally affect the low-shear rheology of the slurries produced from these clays. It was also shown that mechanically working (i.e., pugging) a crude kaolin followed by desliming to remove these impurities can reduce the low-shear viscosity.

Jan 1, 2000

By P. Tsang, S. S. Peng

The stability of longwall chain pillars depends not only on the mechanical properties of the coal and surrounding rocks but also on geological and mining conditions. To evaluate the effects of each variable, orthogonal experimental design was employed in a significance analysis. The study concluded that the stability of longwall chain pillars is mainly controlled by the ratio of pillar stress to pillar strength, the ratio of the Young's moduli of roof to coal and floor to coal, entry width, pillar width and the internal friction angle of coal. Additionally, horizontal stress, panel width and mining height also play a significant role.

Jan 1, 1996

By Vas Choudhry, Randhir Sehgal

Conventional clean coal technologies which consist of coarse coal cleaning by gravity methods and treatment of natural fines by flotation can only remove a portion of the pyritic sulfur and ash in the coal. Higher (+90%) pyritic sulfur rejection is attainable when coals are ground to ultrafine sizes to enhance liberation of the mineral matter and then cleaned. However, cleaning of coal at very fine sizes poses a number of unsolved problems, the chief one being the loss of cleaning efficiency. This, of course, means that liberation of pyrites does not always equal its rejection. In addition, the dewatering of fine- cleaned coal, and its handling, transportation, and acceptability to the utility industry a1 so pose considerable technical and economic problems, especially when compared to the FGD alternative. This paper addresses some of the critical issues involved in the cleaning of ultrafine coal s.

Jan 1, 1989

By J. F. Abel, R. J. Spengler

Convergence measurement across the 17.4-m (57-ft) high shaft station/loading pocket at Mt. Taylor provided continuing verification of stability and safety. Three levels of instrumentation, consisting of three lines each, were installed and monitored. The instrumentation showed that the flexible lining restrained the adjacent rock. The flexible lining consisted of pea gravel with neat cement between rock and liner plate, wooden crush blocks between liner plate and steel ring beams. The loading pocket is elliptical, 11.6 x 9.6 m (38 x 31.5 ft) inside diameter. The crush blocks were designed to allow 15 cm (6 in.) of convergence. Maximum predicted convergence was 7.0 cm (2.75 in.), and 5.7 cm (2.25 in.) was measured. Convergence measurements also demonstrated decreasing deformation with respect to elapsed time and distance from the measurement station to the temporary bottom of the shaft excavation.

Jan 1, 1987

By Pierre Louis, Jacques Duparque

ACTIRED is a new process for gold and silver elution from activated carbon based on the addition of hydrazine, needing no extra investment and which generates a systematic increase in elutions kinetics. This process either operates at a lower temperature and maximizes financial gain or reduces elution time or operates at a compromise between these two options taking into account the needs of each plant. Industrial use of the process at SNC Lastours, France (Zadra elution column 3,5 bars -125°C) has proved at 95 ° C the following points:

Jan 1, 1995

By A. Wahab Khair

There are a number of factors, including mine geometry, local geology, geotechnical properties of overburden materials, surface topography, sequence of overburden strata, and extraction rate, affecting characteristics of surface subsidence imposed by large underground excavation. Among the factors, the first three have the major impact on magnitude and area of influence of final subsidence. Hence, a model has been developed, considering mine geometry and geologic and geotechnical properties of the associated area, to predict maximum possible subsidence and subsidence profile at any cross-section within the subsidence influence zone. Based on extensive field measurements and mechanics of strata behavior, under the action of overburden pressure in the vicinity of the large underground excavation, the vertical plane of influence zone has been divided into five areas: 1) excavated, 2) caved, 3) fractured, 4) highly deformed but continuous, and 5) subsided zones. In the final state of subsidence each area maintains a certain volume expansion/contraction, i.e. a factor which depends on geologic, geotechnical properties of overburden strata and state of stress within the subsidence trough. The cumulative volume expansion and contraction partially compensates for the extracted volume and the difference between the two is reflected as the subsided area in the form of the area within a curve defined by a probability function. The input parameters for the model are mine geometry (i.e. length and width of the panel), depth of cover, and geologic and geotechnical properties of overburden strata (i.e. percentage of hardrock, sandstone and limestone, and soft rock, shale within the overburden strata and Rock Quality Designation). The model calculates angle of draw for the site, expansion factor for each zone utilizing empirical relationships, maximum possible subsidence and plots the subsidence profile curve. The model is developed for a longwall excavation with unique characteristics of prediction of angle of draw and maximum possible subsidence for a given geologic and mining condition at any cross-section within the influence zone of subsidence.

Jan 1, 1986