Search Documents

By Brent K. Nelson, D. Lee Petersen, Charles R. Nelson

INTRODUCTION The Soudan 2 Cavern was completed in 1986 as a physics research laboratory located 713 m below ground in northern Minnesota. A paper in the 1985 RETC proceedings presented the background and planned usage for the cavern, site investigation and rock conditions, contract documents, and a bid summary. This is a follow-up paper describing construction of the cavern. The Soudan 2 excavation, 71.8 m long by 13.9 m wide by 11.6 m high, was excavated by drill and blast methods and mucked by crawler tractor and mine hoist. The excavation sequence consisted of twin top-heading pilot tunnels followed by removal of the top heading pillar and finally the bench. Various blasting designs were used to achieve adequate breakage and acceptable levels of blast damage control at the cavern perimeter. The geologic conditions exposed in the cavern, and the support needs of the rock encountered, are compared to the conditions interpreted from the site investigation. The influence of specific geologic features on cavern performance will be described. Initial support and final lining consisted of full length grouted rockbolts and reinforced and plain shotcrete. Trials were conducted with steel-fiber reinforced shotcrete and microsilica additives. The performance of the rock and support systems was tracked with single point extensometers, convergence measurements

Jan 1, 1987

By J. B. Mitchell

Comminution methods for base metal and precious metal ores have had considerable attention from mine operators, equipment suppliers and design engineers for many years and much of their work has been well reported. This interest derives from a healthy concern with the costs of comminution, often the largest single cost factor in ore dressing of hard ores. Many imaginative innovations have resulted. One notices a trend toward autogenous and semi-autogenous methods, combined with a trend toward very large equipment. Unfortunately, there has been less obvious cost incentive to experiment with softer ores. This is unfortunate because the consequences of inappropriate comminution methods can have an important effect on overall economics by influencing down stream processing and salability of final products. This paper concerns some of the factors to be considered in the selection of comminution methods for potash ores, and gives some specific examples to illustrate some of the principles involved.

Jan 1, 1969

By Malcolm J. McPherson, Satya Harpalani

A thorough knowledge of coal permeability and its variation with factors like stress conditions, and time, is useful in simulation studies of mine ventilation and coalbed methane recovery, as well as characterizing coalbed methane reservoirs. An experimental investigation was carried out to study the gas flow characteristics of coal to enhance the under- standing of the mechanism of methane flow through it. The work consisted of measurement of permeability of coal samples under triaxial stress and an examination of the physical structure of coal using electron microscopy. Effort was made to fit the experimental data to several phenomenological models that have been used to describe fluid flow through porous media. It was realized that gas flow through coal cannot be described by models that assume this flow to be through a bundle of capillary tubes. However, results suggest that this gas flow could be predominantly through fractures and cracks in coal, and this could be represented by flow between parallel plates.

Jan 1, 1986

By V. Vesselinov, S. Orr

"Enhanced heap leaching - Part 1: Insights" (Orr, 2002), different flow and transport phenomena that could significantly reduce leaching recovery were investigated. The combination of such understanding with advanced flow and transport modeling establishes the link between cause and effect, thereby, directing operators to optimal design and construction of new heaps. Modeling of flow and transport in heaps could also point to a unique change in application method or rate that would maximize leaching enhancement of an existing heap under existing situation and leaching history. The use of such a model is cost effective in that it can simulate multiple scenarios of alternative leaching enhancement methods. By simulating a large number of irrigation scenarios, such a model can point to the optimal and/or the most promising alternatives for a particular heap. The authors' simulations concentrate on the effects of changes in application rates and heap design on changes in flow paths and enhanced leaching recovery. Based on such simulations, an intelligent control agent, such as Multiple Resolution Decision-Support System (MRDS) (Meystel and Albus, 2002), could build a new representation of the complex heap-leaching system. And, by learning from historical data and current information, it could provide optimal management of heap leaching and heap decommissioning.

Jan 1, 2003

By A. W. Khair, M. Ahmad

Bit wear has been proven to have a significant effect on respirable dust generation in coal cutting system. The mechanism of bit wear can be adhesion, abrasion, oxidation, or diffusion, depending on cutting conditions. This paper presents a portion of an extensive ongoing series of studies to better understand the principles of bit wear and dust generation. Used bits collected from underground coal mines were analyzed to identify the basic principle of bit wear in coal and rock cutting. Distribution of weight loss and conical height loss of worn bits were studied and bit wear was divided into four stages according to weight loss. Utilizing these worn bits, Laboratory experiments have been camed out to study the effects of bit wear on coal cutting system and respirable dust generation. An Automated Rotary Coal Cutting Simulator was use to perform the experiments. Acoustic emission monitoring is applied to study the effect of bit wear on fracture formation and dust generation.

Jan 1, 1992

For processing plant design it is essential to develop a consistent material and (usually) energy balance as a basis for equipment sizing. This paper discusses techniques for consistent material balance generation, from hand calculation, through spreadsheets to specialised computer programs and general purpose simulations. The appropriate matching of techniques to problem complexity is considered, as are some possible trends for the future.

Jan 1, 1991

By Sepp A. Kutschera

are gaining increased interest for over­burden removal and ore production at large open cast mines. The application of bucket wheel excavators is still tied to soft un­consolidated rocks and soils, while belt conveyors can cope with all kind of matri­als restricted only by the top grain _ size. Therefore, mode of transport and the re­quirement of down stream ore processing de­fine the materials size distribution. These requirements are usually met by primary crushing or scalping. The paper discusses general applica­ tion criteria of bucket wheel excavator with systems primary for in-pit overburden crusher removal. and It _indeapits scalper units and discusses their technical and operational features. It further com­pares the capital and operating cost struc­ture relative to the syste

Jan 1, 1992

By D. W. Olson

Garnet has been used as a gemstone for centuries. However, garnet’s angular fractures, relatively high hardness and specific gravity, being chemically inert and non-toxic and free of crystalline silica, and its ability to be recycled make garnet ideal for many industrial applications. Garnet is the general name given to a group of

Jan 1, 2005

By B. K. Parekh

The International Symposium on Comminution was organized at Camborne School of Mines, Cornwall England. Papers covered the fundamental and practical aspects of comminution in the mineral industry. Although comminution equipment design has not changed fundamentally during the last 50 years, methods of control and optimization have improved considerably. A simulation model for batch ball milling in the rotating mill was developed as a step toward continuous simulation of ball and autogenous milling. New concepts in jaw crusher technology design and the concept of a 1.6- x 2.1-m (66- x 84- in) jaw crusher with open feed throat has resulted in power savings. The use of cone crusher technology in comminution circuits with particular reference to machine design, plant flowsheet and control figuration has been reported by Boliden Allis, of Sweden. The Whiten steady state crusher model form has been used to develop a quantitative model of 2.1-m (7-ft) cone crushers. This was done by incorporating liner age (wear) and liner length as variables on the selection of particles for breakage and thus on the product size distribution. Another paper by Lira and Karetsky discussed the development of a model based on a multisegment ball mill developed by Whiten and Kavetsky. It is capable of simulating the performance of a coarse grinding ball mill of a given diameter, ball size and mill speed.

Jan 1, 1991

By Clay Haynes

While the Kansas River Tunnel is a relatively short, small diameter tunnel, the shaft excavation methods implemented were long and large on innovation and use of reverse circulation drilling equipment. ATS Drilling, L.P. used mechanical excavation techniques for both soil and rock segments of the 42.7 m (140 feet) and 38.1 m (125 feet) deep shafts that were 2.9 m (9.5 feet) and 4.1m (13.5 feet) diameter, respectively.

By W. W. Harvey

The work to be described was part of an exploratory research program directed toward identifying potentially useful but little known reactions in extractive metallurgy. In particular, the major copper sulfide minerals, as a group, have long been considered insoluble in nonoxidizing acids (e.g. Forward and Barren, 1J60; Parsons and Ingraham, 1970; Peters et al. 1972). This generalization was considered to include nonoxidizing conditions in warm aqueous MC1 solutions (Ingraham et al. 1972) and, indeed, was consistent with our own chemical and mineralogical experience. On the other hand, under hydrothermal conditions, copper and sulfide species are carried in solution and deposited as sulfides in mineralized veins. The question that poses itself is: what are the mildest conditions of temperature and fluid composition under which commercially important copper sulfide minerals can be solubilized in the absence of an oxidizing agent? A reference to H2S formation during oxygen-sulfuric acid pressure leaching (Warren, 1958) of chalcopyrite, when the oxygen partial pressure was allowed to fall, provided a clue. In the present study, experimentation with chalcopyrite concentrate in dilute hydrochloric acid, under re flux conditions (in Pyrex flasks) and with an inert purge gas, revealed substantial amounts of H2S production and iron solubilization, cite negligible copper solubilization, after 2 ½ -4 days. Under comparable conditions the extent of reaction with dilute sulfuric, acetic and phosphoric acids was markedly less.

Jan 1, 1976

By F. G. Boehm, T. S. Golosinski

This paper identifies the components of belt conveyor shifting force as a vertical force, Pv, a lateral force, Ph, and a longitudinal force, Pl. A method for estimating these forces is proposed that relates each of their values to the properties of the conveyor structure and rails, the shifting operation parameters, and other site-specific conditions. The effect of this force on the shifter behavior is analyzed, and guidelines are developed for selecting a suitable shifter. As well, other equipment requirements for the shifting operation are discussed.

Jan 1, 1988

By A. Vien

Over the past several years, Svedala has developed a continuous charge monitor (CCM) for tumbling mills. It consists of a strain gauge embedded into a rubber lifter and associated electronics. This paper describes the results of a research program to evaluate the technical and economical merits of such a device on a SAG mill. The evaluation includes validation through discrete element modelling and comparison to measured static volumetric load. Inclusion of the measurement into a control strategy and its potential for condition monitoring is discussed.

Jan 1, 2001

By Harry M. Edenborn, Richard W. Hammack

Experiments were done to determine if a mushroom compost-based sulfate reduction system could be used to treat nickel-contaminated mine waters. Sulfate reduction systems were established in columns containing acid-washed mushroom compost. Simulated mine waters containing 2000 mg/L sulfate and 50 to 1000 mg/L nickel were adjusted to pH 4.5 and pumped through the columns at flow rates between 15 and 25 mL/hr. During the first nine days of operation, virtually all influent nickel was removed in the columns by sorption and ion exchange mechanisms. The nickel removal rate then dropped to 18 to 30 mg Ni/day (7.8 to 12.8 nmol/ g-substrate/day), probably due to low sulfate reduction rates. When sodium lactate was added to the inflow, a sustained and seven-fold increase in the nickel removal rate was observed. Bacterial sulfate reduction rates measured in mushroom compost-based wetlands exposed to coal mine drainage are 2 to 20 times faster than the rates observed in this study. Low sulfate reduction rates in the columns may have been due to the inhibition of microbial activity by high nickel concentrations and the removal of labile organic compounds from the mushroom compost substrate during acid-washing. Results of this study indicate that bacterial sulfate reduction can effectively treat nickel concentrations up to 500 mg/L if labile carbon is nonlimiting.

Jan 1, 1992

By D. J. McCracken

The lithium review did not arrive in time for publication in the June issue The estimated consumption of lithium minerals as raw materials to the glass, ceramic and metallurgical industries in 1992 was 85.5 kt (94,200 st). That equates to about 12 kt (13,200 st) of lithium carbonate equivalent (LCE). An additional 150 kt to 200 kt (165,000 to 220,000 st), or 7.5 kt to 10 kt (8200 to 1100 st LCE), were used in the production of lithium chemicals. The 1992 consumption represents an overall decrease of 3.5 kt (3800 st), or 500 t (550 st) LCE, from 1991. This was a direct result of a worldwide reduction in glass demand due to the economic recession. There are three major producers of lithium minerals. Gwalia Consolidated Ltd. (formerly Lithium Australia Ltd.) in Western Australia and Tantalum Mining Corp. (Tanco) in Manitoba, Canada, both produce spodumene ore. Bikita Minerals, in Zimbabwe, is the largest producer of petalite. Bikita also has the capacity to produce small volumes of spodumene concentrate. The Cyprus Foote spodumene operation at Kings Mountain, NC, ceased production in 1992. It once produced about 2 kt/a (2200 stpy) of "high iron spodumene" for uses other than in the manufacture of lithium chemicals. The lithium products of the major producers are shown in Table 1. The current resources of 13 Mt (14.3 million st) of LCE in the western world will supply demand for more than 50 years.

Jan 1, 1993

By John S. Thayer, Frederick E. Brinckman, Kenneth L. Jewett, Gregory J. Olson

Interest and research in biorecovery of metals has focused mainly on cell-based metal leaching and precipitation. However, production of non-enzymatic metabolic products by microorganisms related to metals bioprocessing also deserves attention. For example, it is well known that biogenic inorganic (e. g. H2S04 ) and organic acids play a role in metal dissolution. There are other metabolic products of microorganisms which can catalyze useful metals transformations. These include methylated metabolites such as alkyl halides which can dissolve metals from ores and also reduce certain metal ions in solution to pure metallic particles. This paper describes some of our research on metal dissolution and precipitation by such metabolites. Examples include the production of high purity elemental metal particles of gold, platinum and palladium by volatile metabolic products.

Jan 1, 1989

By X. Shi

This paper presents design and implementation details of a fuzzy-behavior-based controller for an automated excavator. The robotic excavator is equipped with sensors, actuators and an embedded control system. The excavator controller uses neural-networks to interpret forces and torques gathered during the excavation process from bucket-mounted force sensors. Implementation details card experimental results using the fuzzy-behavior-based excavation controller are given for several excavation tasks. These excavation tasks demonstrate some of the complex skills that are essential for an autonomous mining-excavator controller.

Jan 1, 1997

By John F. Spisak

Versatile living organisms, historically exploited as functionaries in the food processing, pharmaceutical and chemical industries, have not been successful in achieving similar or significant acceptance within the minerals industry. The current biotechnical revolution coupled with its expanded understanding, dictate that a flagging minerals industry reconsider the use of biotechnology in metallurgical applications. Living resources, either singly, in commensal association or in complex communities, are capable of duplicating fully integrated and complex processing functions. Organisms can mine and extract metals, detoxify chemical effluents and synthetically produce compounds. They have been criticized as exhibiting poor kinetics, excessive energy consumption and environmental sensitivity. However, expanding knowledge reveals that these organisms are surprisingly adaptable, variable and extremely durable. Applied biotechnology in specific cases offers favorable economic returns, environmental benefits and aesthetic value. Selective implementation of living systems can offer opportunities for reduced labor, increased productivity and technological advance. Success will not come easily. Capital must be risked, controversial decisions made and new ground plowed. Traditional, specialist thinkers will of necessity give way to interdisciplinary expertise and unorthodox methodology if success is to be achieved. Those who vigorously persevere, however, are likely to be rewarded with a dynamic and profitable new role in a restructured minerals industry.

Jan 1, 1985

By Terry Mattioli, Buck Bradshaw, Terry Fagg, Larry G. Nisle

Deposition of calcium carbonate scale on activated carbon in the Pinson Mining mill carbon column circuit was causing erratic gold recovery rate, long acid wash time, high carbon attrition and long strip times. Continuous addition of a blended antiscalant into the mill thickener overflow at 8 ppm reduced the average carbon acid wash weight loss from approximately 10% to < 2%. Cleaner carbon improved the gold loading rate in the mill column. The loading on Column I was increased to 175-225 oz/ton carbon from 125-150 oz/ton for a two-day carbon advance cycle. The higher loading capability has given Pinson more flexibility and better control of gold flow through their carbon adsorption, stripping and electrowin­ning processes. Preventing calcium carbonate build-up on activated carbon with this antiscalant reduced acid wash batch time. This enabled Pinson to acid wash and regenerate every batch of stripped carbon for all the adsorption circuits. Shorter strip times have also resulted from the lowering of the calcium carbonate scale level in the loaded carbon. Carbon consumption has been reduced and is now averaging 0.046 lb/ton ore for the first six months of 1990 compared to 0.072 and 0.083 lb/ton respectively in 1989 and 1988.

Jan 1, 1990

By D. J. Fitzpatrick

The paper reviews current mining subsidence research at The Department of Mining Engineering, University of Notting- ham. Special attention is being devoted to prediction of ground movements between the mining horizon and the surface using physical and computer-based models. The paper presented discusses linear and non- linear finite element methods and compares results with those from physical models and field observations. Special attention is focussed on the determination of the effect of caved zones on overlying and underlying geological structures. The paper presents data from comparisons with U.K. case histories.

Jan 1, 1986