Search Documents

By S. Eugene Sankey, Geoffrey L. Payne

Fundamental choices in flocculant selection often come down to the lower cost of solid grade products versus the convenience of liquids. The ideal product would be a low cost solid grade flocculant which requires minimal handling and no sophisticated dissolving equipment. Recent polymer developments have lead to the commercialization of a limited range of dry polymers that can be screw fed at controlled rates directly to process streams without the need for predissolving. Other developments include dry polymers that can be directly added to mix tanks without the need for sophisticated wetting systems. The latter will make dry flocculants especially attractive for smaller users. Examples of these new products and their application in industrial and municipal waste treatment will be provided.

Jan 1, 1994

By I. Fafoutis

Laboratory column studies were conducted in order to assess the effectiveness of slag and red mud reactive barriers for cleaning up leachates generated at mining and waste disposal sites and loaded with copper and manganese. Solutions containing the metals of concern were prepared by dissolving the required quantities of CuSO4?5H2O and MnSO4?H2O in distilled water so that Cu concentration was 100 ppm and Mn 20 ppm. Flow rates of 25 mL.h-1 for Cu solution and 75 mL.h-1 for Mn solution were used in order to simulate aquifer water velocities of 1 ft/d and 3 ft/d respectively. Solutions were pumped upflow, in Plexiglas laboratory columns filled with each reactive medium, using peristaltic pumps. Measurements of middle and outflow column pH, redox potential, conductivity and elements concentration were performed to provide information regarding removal mechanisms for both elements and exhaustion/inactivation rates for each reactive medium. Both reactive media showed fairly good removal efficiency over the period studied. Copper was mainly removed by precipitation and formation of Cu(OH)2 while removal of manganese was due to precipitation of Mn(OH2).

Jan 1, 2006

By P. F. Ziemkiewicz

This project evaluated the performance of nine passive treatment methods by studying 137 treatment units in eight eastern states. Performance was normalized according to construction cost, projected service life and tons of acid load treated. Results were dimensioned as $/tons of acid load treated/year. These costs were then compared to those of chemical treatment. Sites that achieved acid load reductions at costs below those of chemical treatment were considered successful. In addition to evaluating the performance of the treatment methods, this paper describes the various passive treatment systems, their applications and performance data for individual treatment units.

Jan 1, 2003

By Richard W. Kimball, Richard F. Coon

This paper describes drill and blast excavation and groundwater control measures at the Lake Mead Intake No. 2 project. The construction includes a deep access shaft, intake shaft, surge chamber, forebay chamber, intake tunnel, 22 well shafts and East Tunnel. Grouting ahead of the excavation face was used extensively during shaft and tunnel construction. Lake Mead Intake No. 1 was constructed in the early 1970’s under less severe groundwater conditions and this work was delayed by ground conditions and water control problems. Excavations for Lake Mead Intake No. 2 must be completed in 23 months to meet SNWA’s water delivery schedule.

Jan 1, 1999

By Z. Stanojevic-Simsic

The aim of this paper was to study sludge dewatering. The sludge which was examined in laboratory scale was produced by neutralization of a mixture of metallurgical wastewaters. Experiments were carried out using synthetic wastewaters with chemical composition similar to that of metallurgical wastewaters, resulting from electrolyte regeneration, copper refining and precious metals recovery. During investigations gravitational and vacuum techniques were examined. Parameters such as water volume, height of sludge and time of dewatering were monitored. In this paper the results obtained are presented and discussed. The application of vacuum filtration enables better dewatering and compaction of sludge.

Jan 1, 2006

By H. F. Hennigar, D. L. Pawson, E. J. Foell

Results of an analysis of abyssal benthic megafauna based upon review of nearly 250 hours of videotape and 2149 bottom photographs are presented, and the utility and limitations of such analyses in deep sea biological studies are discussed. The images were acquired at depths of 4400-4800 m during a resource assessment cruise aboard the RV Prospector using a unique, deep-towed, television telemetry system coupled with 35-mm photography. The data review was carried out in support of NOAA efforts to provide adequate environmental baseline information before industrial exploitation of nodule deposits and concurrent monitoring begin.

Jan 1, 1991

By M. J. Klishis

This paper presents the findings of a study on roof bolter's hazard exposure. A "microanalysis" of accident data was combined with ergonomic observations of roof bolter operators to categorize bolting-related injuries, and, from this, a checklist was constructed. Bolting-related problems were identified as situations that could expose bolter operators to hazards. Approaches to avoid these situations were applied at six mining operations to evaluate specific problems in root bolting operations. The research emphasized the importance of analyzing worker behaviors in the context of mining situations and equipment-design problems that lead to human-error accidents.

Jan 1, 1996

By Wilhelm J. Kogelmann

The concept and operation of novel shaft sinking systems utilizing roadheader-type cutter booms, including mucking, conveying, and hoisting installations, are described. Selection criteria, performance data, and economic considerations for various shaft excavators are presented. Various applications of this low-cost and flexible system for civil engineering and mining projects will be discussed. The cutter booms can work in both soft ground and competent rock. Furthermore, the novel excavator can operate in ground stabilized by grouting, cementing, and freezing. The flexible cutting system can be used both for excavation of shafts, foundation pits, slopes, and for tunneling (drifting).

Jan 1, 1989

By Leszek W. Lunarzewski, Adam L. Lunarzewski, Raymond C. Pilcher

The Floorgas and Roofgas simulation programs are used to identify strata relaxation zones and their boundaries, to assess active gas sources from coal seams and gas¬bearing rocks and to determine relevant gassiness prediction coefficients for any local longwall. The paper shows that by use of the print-outs from the Floorgas and Roofgas programs the following benefits are achievable: • identification of the shear and gas discharge zone positions in the floor, strata relaxation angles and various gas discharge zone positions in the roof, which are both relevant to local geological and mining conditions • optimisation of cross-measure drainage hole length, location, number and angle of inclination calculation and definition of gas make prediction coefficients such as the release ratio from adjacent coal seams, specific gas emission during longwall extraction and the relationships between gas make, longwall width and coal production levels.

Jan 1, 1995

By Alec G. Richardson, S. H. Chiang, Ralph W. Lai, McMahan L. Gray

The potential of coal cleaning by selective agglomeration was examined for a Pittsburgh seam bituminous coal using isooctane as an agglomerating liquid. The effects of particle size, pH, degree of mixing, and dosage of isooctane on the pyrite and mineral matter removal from finely ground coals were investigated. The role of shear-enhanced-hydrophobic-association in the flocculation of fine particles was examined. The degree of liberation of pyrite from coal at different grinds was examined using an automated petrographic image analyzer. The effect of dispersant on slurry rheology during grinding was studied. The results indicate that over 95 percent of the pyritic sulfur can be removed from the coal. Final products containing less than 0.9 percent ash at a combustible recovery in excess of 90 percent have been obtained with multiple stages of cleaning.

Jan 1, 1989

By Z. T. Bieniawski, Nicholson G. A.

This paper describes an empirical constitutive model for underground excavations in rock which equates the deformation modulus to the ratio of the principal stress difference to the major principal strain. The model requires failure criteria which define both the stress difference at failure and strain as a function, in part, of rock mass classification ratings (i.e. Bieniawski's RMR and Barton, Lien and Lunde's Q). Available failure criterion allows reasonable estimates of the stress difference for intact rock as well as rock mass. However, a suitable failure criterion for estimating strains at failure for rock was not available. Toward this end, this paper describes the development of an empirical criteria for defining strain at failure for intact rock as well as methodology for developing similar criteria for rock mass.

Jan 1, 1986

By A. D. Trujillo, R. D. Wunder

The Chino Mines Co., a Kennecott- Mitsubishi partnership, located in Hurley, NM, recently completed a $405 million modernization of its mine, concentrator, and smelter facilities. The mine/concentrator modernization commenced in 1980, and the smelter modernization began during 1982. Modernization of the mine and concentrator facilities involved increasing the mining rate from 98 kt/d (108,000 stpd) to 152.2 kt/d (167,800 stpd). Ore mining was designed to increase production from 20.2 kt/d (22,300 stpd) to 34 kt/d (37,500 stpd). A new concentrator was con- structed near the mine using semiautogenous grinding. The new smelter uses the INCO flash smelting process, increasing capacity by 40.8 kt/a (45,000 stpy) to 99.8 kt/a (110,000 stpy) of saleable copper.

Jan 1, 1988

By Park. D. W., Y. M. Jiang, L. A. Morley, W. Keeton

Underground room-and-pillar mining operations in the Warrior Coal Field in Alabama frequently suffer instability due to soft floors and thinly-laminated immediate roofs. This investigation concerns a mine that was experiencing ground-control problems with weak floor conditions. Several roof falls occurred locally, and as much as 0.6 m (2 ft) of floor heaves have been experienced. The paper presents the results of comprehensive analyses conducted on floor heave, roof sagging, pillar- penetration and floor bearing capacity using instrumentation and numerical modeling.

Jan 1, 1993

By James E. Monsees

Extensive underground excavation will be required for construction of a mined geologic repository for nuclear waste. Hundreds of thousands of feet of drift will be required based on the conceptual layout design for each candidate nuclear waste repository. Comparison of boring and blasting excavation methods are discussed, as are special design and construction requirements (e.g., quality assurance procedures and performance assessment) for the nuclear waste repository. Comparisons are made between boring and blasting construction methods for the repository designs proposed for salt, volcanic tuff, and basalt. Differences in the geologic media and settings of the prospective sites influence the excavation method in terms of drift length, size of opening, drift slope, rock quality, and boreability. Support requirements, ventilation, and the ability of the geologic system to retard radionuclide migration are also directly impacted by the geology and excavation method.

Jan 1, 1987

By Darryl Amick, Keith A. Prisbrey, Lee E. Plansky

The problem addressed was to develop automated image analysis of metal welds to replace unreliable and costly 100% visual inspection. The objective was to evaluate neural networks combined with features from gray level surfaces. Photomicrographs of the welded seam in Zircaloy-4 channels used in nuclear fuel rod assemblies were examined. The methodology used was to select a set of morphological feature coefficients from Bessel Fourier morphological feature coefficients extracted from digitized photomicrographs. The selected morphological feature coefficients were then used to train a neural network. The approach was verified initially by successfully training a neural network using the known, secondary chemistry of the alloy welds. The results were good. The Bessel Fourier coefficients captured sufficient information from the metallographic images to distinguish weld quality. This approach has the combined advantages of compressing the images through Bessel Fourier coefficients and give the ability to rapidly process large amounts of data using neural networks.

Jan 1, 1993

By B. Ceccarelli

Many public domain programs useful in mining engineering, e.g., MULSIM, DZTAB, and EXPAREA, require tedious data input and generate pages and pages of printed output. To eliminate the tedium and to enhance the output, ETI U.S., Inc. developed GEM, Graphics for Engineering and Mining, a collection of application programs and underlying interface tools for VAX/VMS computers. This paper presents an example of how an application program in GEM enhances a specific public domain program. It describes how GEM provides automated graphics assisted input and output. The paper describes how this program uses the GEM User Interface: the 3D GKS device independent graphics, server and drivers, various mining, mathematical and statistical algorithms, the means of handling graphics, data including IGES, and the foreign language interface.

Jan 1, 1992

By Y. A. Attia, M. Elzeky

The effects of bacterial adaptation and partial replacement of leaching solution on the rate and extent of bioleaching reactions of a complex sulfidic gold ore were investigated. The ore was first concentrated by bulk sulfide, flotation, and the sulfide concentrate was treated by bioleaching using Thiobacillus ferrooxidans. The residues from bioleaching were treated by cyanidation to extract the gold and silver. Bacterial adaptation before bioleaching significantly increased the rate and extent of bioleaching reactions. Similarly, the daily partial replacement of leaching liquor enhanced to a great extent the leaching rate, and in some cases, increases of up to ten fold were observed. Both bacterial adaptation and solution replacement increased the gold recovery by about 2-fold and that of silver by about 1.3-fold. In this work, more than 95% of the gold and more than 98% of the silver could be recovered from the sulfidic gold ore when bioleaching was used ahead of cyanidation, compared with 18.3% and 52.3% by direct cyanidation.

Jan 1, 1992

By d&apos, J. A. Oliveira, A. K. L. Resende, L. F. G. Assumpção, J. D. Neto

Kaolin samples from Rio Capim Resources were treated in conventional and superconducting magnetic separators to study the main variables that influence the impurity removal process. Two coating clays and a delaminated clay were tested. The variables studied were retention time (cross-sectional velocity), magnetic-field intensity and matrix type. The feed brightness ranged, from 84.7% to 87.6% ISO, for the coating clays and ranged from 80.7% to 85.4% ISO for the delaminated clay. Using a conventional magnetic separator with an applied, field of 1.5 to 2.0 T (tesla), the brightness values were higher than 88% ISO for the unleached coating claw products and were higher than 87% ISO for the unleached delaminated product. With a maximum field intensity in the superconducting machine of 5.0T unleached brightness values higher than 88.5 % ISO were attained for both coating and delaminated clays.

Jan 1, 1997

By J. Dasher

Regarding the March 1991 ME technical paper by De Souza and Moore: For more than a decade since my February 1981 article on how to use modern metric, which SME-AIME had decided to do, I have monthly pointed out metric errors to the editors. In part, I do this because there has been no action to al low editors to fix figures and tables or to allow them to require authors to do so. The latest resulting atrocity provokes this discussion of vibrating drill handle units being stated in decibels.

Jan 1, 1991

A one-day seminar designed to help quarry and mining managers make their operations more productive, more efficient and less expensive was held in Harris- burg PA. "Rock-Solid Productivity" was sponsored by Pittsburgh Power & Light (PP&L). The seminar, one of a series sponsored by PP&L in 1997, proved to be well-organized and provided valuable information to the many quarry and mining professionals who attended. The information presented included a comparison of on-site diesel power vs. electric power, discussions of equipment improvements and topics on environmental management.

Jan 1, 1998