Search Documents

By Satoshi Honda, Mitsuru Shimizu, Tatsuji Nagao, Motoaki Kurisu, Hirokazu Izumi, Toshinori Takahashi, Hiroyuki Itoi

"1. INTRODUCTION Grade separation of roads and railway tracks is an effective method for solving traffic-related issues in cities. However, in urban areas where the existing traffic infrastructure is already overcrowded, construction of new roads often faces problems especially in the proximity of existing structures. This paper summarizes the construction plan and results of new road tunnel construction in the proximity of the piers of elevated tracks on the Tokaido Shinkansen railway.2. SUMMARY OF CONSTRUCTION AND ISSUES Auxiliary Route No. 26 as specified in the Tokyo urban plan is a project by the Tokyo Metropolitan Government, covering the construction of a new road with a total length of 22.3 km currently on the way to completion. In Shinagawa Ward, Tokyo, Auxiliary Route No. 26 is designed to cross the railway tracks of the Yokosuka Line and the Tokaido Shinkansen Line, so for this project, the East Japan Railway Company (JR East) was commissioned to design and build a road crossing under the railway tracks (Sumiyoshi Underpass). Figures 1 through 3 show a sketch of the Sumiyoshi Underpass. The Sumiyoshi Underpass was planned as a two-lane tunnel for vehicles, which was to cross under the railway tracks of the Yokosuka Line and the Tokaido Shinkansen Line at an angle of 70 degrees. The structure concerned is a single-story single-span box culvert structure with the following dimensions: 11.5 m wide, 7.7 m high and 31.6 m long. The Tokaido Shinkansen Line tracks were constructed on a girder-type elevated bridge built in the 1960s, and the foundation piles of the piers (P7 and P8) in the proximity of this crossing box culvert of RC structure were constructed using an earth drill method. The crossing structure for this project is located extremely close to the piers of the Tokaido Shinkansen railway tracks, with a minimal separation of 0.4 m, and the most significant issue of this project was construction in a manner that would not obstruct the normal operations of the Tokaido Shinkansen (Figure 4). Initially, we considered installing a temporary earth retaining structure in the proximity of the piers, cutting the ground and building an RC box, but concluded that it would be very difficult to apply this method because of probable excessive displacements in the Shinkansen railway piers. That is why we decided on the use of a non-open cut method in order to minimize the impact on the piers."

Jan 1, 2016

By Hai Lin, Renshu Yang, Yongliang Li, Shizheng Fang

With the aim of solving the large deformation problem of surrounding rock in coal mine roadways with a thin sand-mudstone interbed roof, transportation roadway 1603 in Haoyuan Mine was considered. The failure mechanism of surrounding rock was studied through comprehensive on-site investigations, borehole image analysis, mineral composition analysis, and other means. Numerical simulations were performed to determine the influence of roof layer thickness, lateral pressure coefficient, and coal rib strength on the stability of the interbedded roof. The main reasons for support failure and deformation of the roadway are softening and swelling of the sand-mudstone interbed roof upon exposure to water, insufficient support capacity of the roof due to the soft coal rib, an unreasonable support scheme, or poor construction quality, which can reduce the bearing capacity of surrounding rock. Based on our analysis, a control strategy was devised for a thin coal-mudstone interbed roof. The support scheme combines long and short cable support, strengthening of the coal rib to consolidate the roof, and partially shotcrete grout, and was found to improve the overall mechanical strength of surrounding rock and maintain the stability of the thin sand-mudstone interbed roof. The results of the numerical simulations and monitoring data indicated that the proposed support scheme effectively controls the deformation of the surrounding rock of thin sand-mudstone interbed roof of coal mine roadways while maintaining the safety and stability of the surrounding rock and supporting structure.

Dec 12, 2022

By M. D. McInnis

The Jualin Gold Prospect is centered on Johnson Creek, approximately 40 air miles north-west of Juneau, Alaska. The property is on the southern end of the Kakuhan Range with Berners Bay immediately to the south and Lynn Canal to the west. The property is accessible directly by helicopter from Juneau or by float plane to the head of a 5.5 mile gravel road that begins on the north side of Berners Bay and terminates at the old workings of the Jualin Mine near the center of the property.

Jan 1, 1989

By P. H. Qi

Activated carbon loaded with gold from different halide solutions has been characterized by thermal analysis techniques. The mechanism of gold uptake by carbon varies from predominately adsorption for gold iodide to predominately reduction for gold chloride. TGA and DT A measurements confirm the existence of adsorbed gold-halide species within the micropore structure of carbon. These results suggest that the ration of reduced; adsorbed gold increases for gold halides in the order Au-I > Au-Br > Au-Cl. In the case of Au-I, TA results for the loaded carbon were compared with pure compounds of 12, AuI and AuI3.

Jan 1, 1996

By M. Polat

Variations in flotation rate by particle size and specific gravity have been investigated for three different bituminous coals. The flotation rates for various components were determined by separating the products of bulk flotation into size-specific gravity fractions. The effects of feed size and reagent addition on the flotation response of individual size-specific gravity fractions were evaluated.

Jan 1, 1994

By Jerry C. Tien

In 2009 China mined 2.695 billion metric tones (Gt) of raw coal. It is estimated that only 3-5% or roughly 135 million metric tones (Mt) of these were mined from 300 some surface operations. Except for a dozen or so large modern operations, most of China's surface coal operations are small by western standards, with annual production ranging from a few thousand tones to 300,000 metric tones (mt). Depending on the size of operations, equipment used range from small trucks and shovels to large bucket wheel excavators and draglines in sizable pits. This article provides a brief overview of China's surface mineable coal reserves, mining methods commonly used and increasing environmental concerns; introductions of several large surface operations are also provided.

Jan 1, 2012

By John S. Summer

The induced polarization (IP) method of geophysical exploration is capable of detecting even small amounts of metallic luster minerals in a rock mass. Consequently, in the years since discovery, IP surveying has become the most popular ground geophysical survey method. It is not too difficult to understand many applications of IP surveying as used in the search for mineral deposits. However, the basic theory of the IP phenomenon is not well developed or understood, and there has been some disagreement on fundamental concepts. In order to most effectively apply the IP method in the field it is necessary to know the physical characteristics of the sought-for deposit including its size, shape, depth, and electrical properties. With this information an optimum IP search arrangement can be devised and one could use the best possible electrode interval, type of array, and line spacing. With uncertain target characteristics as encountered in the real world, geological guidance must be used to help direct an optimized IP survey.

Jan 1, 1972

By A. B. Cecala

Two recent Bureau studies evaluated workers' dust exposures in automated pallet loading processes. The first study involved a Bureau designed dust control system using a push-pull ventilation technique. The unit was shown to reduce workers' dust exposures by 76% during pallet loading at a ground silica operation. A hydraulic lift table was used to automate the bag stacking process; this kept the loading height constant throughout the entire pallet loading cycle. The second study evaluated different commercial automated pallet loading systems. These systems automatically stack the bags onto pallets, shrink wrap the pallets, and deliver the pallets to a fork lift pickup location. Results from a ground silica evaluation site indicated respirable dust samples taken were below the Threshold Limit Value (TLV) as established by the Mine Safety and Health Administration (MSHA).

Jan 1, 1990

By J. Alderman

In modern industry, cost and productivity concerns and environmental concerns are sometimes incompatible, but at other times only appear to be incompatible. Surface disposal of wastes from coal preparation plants appears to be an area of the production system with little opportunity for initiating measures which cut costs and concurrently benefit the environment. However, improving the recovery efficiency of fine coal circuitry can cost-effectively reduce the plant waste environmental burden by a substantial amount. Studies at Jim Walter Resources indicate that fine-coal waste measuring 50% ash contains over 50% recoverable, marketable coal. Modifications to the plant circuitry which reduce the amount of misplaced coal in the fine-coal waste stream could substantially reduce the volume of fine waste disposed aboveground. Studies at Jim Walter Resources indicated that episodic overloads of the vacuum filters in the fine-coal circuits at the preparation plants were a source of misplaced coal in the fine-waste stream of the cleaning plants. To improve the filtration rate and reduce overload episodes, conventional rotary blowers were replaced with high pressure air blasters on most of the filters. Subsequent testing indicated that measurable benefits can be derived from this modification.

Jan 1, 1990

By F. Ysla, M. Mendoza

This proposal, based on the CIEMAN Cajamarca - Hualgayoc initiative, focuses on “Transforming Abandoned Mine Lands’’ We aim to study and assess the feasibility of an innovative rehabilitation method. Contaminated soils will be moved from the upper to the lower site, encapsulated with geosynthetic barriers, and covered with topsoil. The decontaminated upper area will be used for planting trees and large-stemmed plants for hiking and tourism, while the lower encapsulated area will support livestock and short- stemmed crops. This study will evaluate the economic viability and multi-use potential of this technique, promoting sustainable land recovery in Cajamarca, Peru.

Feb 1, 2025

By A. A. Densmore

Telluric Current is that portion of the electric field observed at the surface of the earth which is of an alternating nature, and which is related to solar activity and events in the ionosphere. The primary electromotance which drives the telluric current is the result of the induction process associated with time variations in the earth's magnetic field. The relationship between the electric and magnetic components of this electromagnetic field depend upon the conductor. For our purposes, we are dealing with frequencies f in the range

Jan 1, 1972

By Charles E. Mauk

In 1970, recognizing the great need for an economical, high capacity chemical oxidation process for wastewater treatment, Houston Research began a fundamental study of the available technology, Included was waste characterization; oxidation chemistry for molecular oxygen, ozone and catalyst initiators; kinetics of reaction; gas-liquid contacting methods; and optimization of staged reactors for mixed wastes. Although ozone is the most powerful oxidizer available, the literature contains contradictory reports of its speed and effectiveness. It is now felt to be most likely that many of these early investigations were limited by the ineffectual transfer of ozone from the gas phase into the liquid, and so the investigators were really observing the effects of mass transfer and erroneously trying to interpret the results as if they were chemical reaction data. HR's work considered the cost and effectiveness of gas-liquid contacting in a packed tower, gas sparged contactor, ejector with hold-up tank, and a completely mixed, sparged contactor. The sparged, mixed contactor was found to be most effective and least expensive, and a later investigation settled on the reactor configuration shown in Figure 1 because of its effectiveness of mass transfer and because it lends itself to direct scale-up techniques using laboratory data to design larger reactors.

Jan 1, 1975

By J. Baz-Dresch

A custom-designed shotcrete system, consisting of an 8-m3 (10-yd3) transit mixer and a shotcrete spray boom carrier, is used bya 2-man crew to transport and place up to 25 m3 (32 yd3) of steel-fiber reinforced, dry, silica fume shotcrete per II-hour shift. Shotcrete is custom blended by a local supplier and delivered predampened. Mix design and quality control is performed with a computer program that develops and graphs a properly balanced mix based upon the materials sieve analyses.

Jan 1, 1991

By C. Zhou, R. Jacksha

This paper reports measurement results for radio frequency (RF) propagation around 90° corners in tunnels and underground mines, for vertically, horizontally and longitudinally polarized signals. Measurements of signal power attenuation from a main entry into a crosscut were performed at four frequencies — 455, 915, 2450 and 5800 MHz — that are common to underground radio communication systems. From the measurement data, signal power loss was determined as a function of signal coupling from the main entry into the crosscut. The resultant power loss data show there are many factors that contribute to power attenuation from a main entry into a crosscut, including frequency, antenna polarization and crosssectional entry dimensions.

Jan 1, 2016

By Martin Herrenknecht, Karin Bäppler

The last five years have seen a remarkable increase in tunnelling projects in both soft ground and hard rock applications. Part of the increase is a result of recent Research & Development efforts to improve Tunnel Boring Machine (TBM) adaptability, capability and reliability. This paper will review the latest innovations in the TBM industry and explain in detail the results of these innovations followed by a forecast where the technology will take the tunnelling industry in the future.

Jan 1, 2005

By Stephen W. Denton

Planning a mining operation in Alaska will involve the investigation of many parameters common to mine planning anywhere. However, there are some unique circumstances that must be recognized when one considers development of mining operations in Alaska. This paper will not attempt to provide a blueprint for mine planning in Alaska, but hopefully will provide a better understanding of the truly unique nature of the northern latitudes. Given this understanding, the mine planner can better assess the potential hurdles along the road to a successful mining operation. The regulatory trend towards uniform standards for mining throughout the United States exemplifies the necessity for Alaska to prove its unique position in the natural resources picture. The factors which make Alaska truly different from the "Lower 48" can be summarized by four points 1) Remoteness and Size 2) Seasonable Extremes 3) Geologic Immaturity 4) Vegetation and Wildlife

Jan 1, 1984

By L. Bloom

In 1996, lack of confidence in assaying methods and sample handling affected companies as diverse as Bre-X and Timbuktu. Share prices and the ability to raise financing are impacted when the quality of assay data is suspect. Overseas projects are subject to enhanced scrutiny when local facilities are used that are unfamiliar to brokers, financing agencies and banks. Quality control systems can be implemented but there are associated costs. These costs should reflect the risk to the mining company, investors and financiers and the size of the proposed investment. In this regard, assay control can be considered a form of insurance to enhance the value of an exploration or mining project. Providing reliable assay data in a production laboratory is challenging. Pressures such as time constraints and profitability affect data integrity. In Australia and North America, reliable assaying services have been provided by several laboratories. Mistakes are primarily due to human error but systems are available that monitor results and identify these types of errors. As the mining industry expands globally, mining companies encounter difficulties in some of these areas due to lack of infrastructure, poor communications, bureaucracy and political risk. These challenges also apply to the operation of laboratories, enhancing the risk of compromised data.

Jan 1, 1997

By Louis A. Panek

Using an approach based on the theory of similitude, the author develops a general equation and related concepts that provide new insights to an old problem. The load-bearing capacity (strength) of a square, rectangular, or cylindrical prism of a brittle material such as rock, coal, or concrete is expressed as the mathematical product of a size effect, a shape effect, and a function of the mechanical properties (deformability, cleat/joint spacing, and friction) of the pillar, roof and floor materials. Through an application of multivariate statistical analysis, the results of assorted tests and observations of failed pillars can be combined into a fundamental scaling equation, which provides a unified, consistent approach to the estimation of mine pillar strength. The form of the equation is sufficiently general to be able to incorporate refinements in the characterization of the basis factors, as they become available through future experimentation and analysis.

Jan 1, 1979

By H. J. Hutson

BRS, Inc. has utilized Carlson's Natural RegradeTM software to design the reclamation and stabilization of abandoned open pit uranium mine spoils, AML Project 16N, located in the Gas Hills Uranium District in central Wyoming. This work was completed for the State of Wyoming's Abandoned Mine Land Program (AML) on preSMCRA (Surface Mining Reclamation and Control Act) sites for which no reclamation obligation existed. The project successfully stabilized an eroding spoil dump, enhanced the local view shed, created habitat diversity and provided a significant source of fill material for open pit highwall hazard mitigation efforts. Additionally, the project served to evaluate innovative reclamation design methods, engineering software and grade control technology. This project was nominated for a National Association of Abandoned Mine Land Programs award by the State of Wyoming. The results of this project will be presented as a case history of the Natural RegradeTM approach to surface mine reclamation. Based on the successful application of this new mine reclamation technology on the AML 16N Project, reclamation designs for spoils associated with planned underground uranium mine operations at the Velvet Mine in the Lisbon Valley Uranium District of Utah for Uranium One USA, Inc have been prepared and will be presented. Critical elements will be the encapsulation of unsuitable materials, long term hydrologic stability, and sequencing and staging of ore and mine waste for final reclamation surface construction. The goal of the Uranium One Velvet Project will be to apply best available technology to reclamation planning and fully integrate the reclamation design with the mine planning. Benefits of the approach should include improved public and regulatory perception of the project, facilitate mine permit approvals and the eventual timely release of reclamation bonds, as it is anticipated the stable landform created through this process will result in more rapid stabilization of the site to pre-mine geomorphic conditions. NATURAL REGRADETM CASE STUDY AML Project 16N, D-9 and K Pit Reclamation Project, is located in an intensely disturbed area of the West Gas Hills Uranium Mining District in Fremont County, Wyoming. The overall design calls for the placement of approximately 7 million cubic yards of backfill materials in the D9 and K Pits, imported from adjacent mine spoils including the Central Spoils, and from local highwall excavation. Figure 1 shows the location of the Central Spoils excavation area, as well as the D9 and K Pits fill area. The entire project is located on public lands administered by the Bureau of Land Management, Lander, Wyoming District Office. No access controls are in place at the abandoned mine sites. The public lands are administered under a multiple use land policy including grazing of range land, public recreation, active mining and exploration, and oil and gas. The project site is located along Fremont County Road No. 5, which is a moderately well traveled road. Reclamation of the numerous and large abandoned open pits in the Gas Hills Uranium District has reduced the risk of death or injury to the public. Site History and Background The Gas Hills Uranium District was mined by multiple companies during the period from 1955 to 1981. The uranium was hosted in the Wind River formation, a sequence of soft sedimentary layers of interbedded sandstone, clayey shales, and conglomerates. Uranium was precipitated out of ground water in classic roll front deposits, which are found from very near surface to depths greater than 400 feet. Prior to the enactment of the Surface Mining Control and Reclamation Act of 1977 (SMCRA), very little reclamation work was performed when mines were abandoned or closed. The State of Wyoming Abandoned Mine Lands Program has worked to mitigate hazards associated with large open pits, control migration of unsuitable materials and restore watershed functionality of lands in the district. Additional reclamation is being performed by mining companies on bonded lands. Figure 2, Gas Hills Uranium District aerial photograph, shows the extent of the mining disturbance in the district. [ ] Project Hazards and Concerns The purpose of AML Project 16N is to mitigate hazardous conditions and risk to the public associated with open pit highwalls and toxic, acid forming, and /or radioactive mine waste materials. The D9 and K Pits are contiguous open pits characterized by an 8,800 foot long hazardous highwall that averages over 200 feet tall. In addition to the physical hazard presented by the highwall, the project addresses

Jan 1, 2009

By C. L. Glorioso

As an introduction and credentials for our talk, let me take a moment to introduce you to Wimpey Worldwide and specifically to Wimpey Minerals, USA, Inc.

Jan 1, 1995