Search Documents

By J. E. Miller

The development of a new means of measuring the relative abrasivity of a slurry came about by necessity in 1967 during a full scale loop test of a 560 H.P. reciprocating pump handling magnetite slurry. In order to evaluate the life of expendable fluid end parts, the question of the amount of attrition in a re-circulated slurry had to be considered. An expected reduction in abrasivity as a result of this attrition would certainly give erroneous data on a parts life test. There- fore, some means of measuring such change in abrasivity became imperative. Several test methods were investigated1 but it was felt that these did not fully represent the wear due to back and forth rubbing action associated with a reciprocating pump. A "rubbing block" device used some years ago to determine the quality of hard facing materials was recalled, along with its shortcomings, in that an attempt was made to suspend a small percentage of abrasive particles in a colloidal viscous "mud". Erratic results were attributed to the fact that it was difficult to maintain a consistent slurry concentration under the metal wear block and the reciprocating speed was not great enough to maintain good agitation.

Jan 1, 1973

By A. D. S. Gillies

The use of refuge chambers for use in handling underground emergencies is an issue of topical relevance within the US mining industry. Chamber design is of importance to meet some new safety requirements of US federal and some state government mine regulations. A review has been undertaken of a steel mine refuge chamber design to predict what will be internal temperature within the chamber over an extended period with miners present? The design has been examined for the situation when the chamber is sited in still mine air. Spreadsheets have been developed to allow various design assumptions to be tested. The evaluation has been undertaken using thermodynamic heat transfer models with some assumptions specified to produce a model of appropriate simplicity but with adequate degree of accuracy. Under normal still air conditions it can be seen that internal chamber conditions rise quickly to often arduous conditions. There will always be quite a few assumptions necessary in complex heat transfer process evaluations. Some important refuge chamber design parameters are: ? External surface area of the chamber, its wall thickness and construction. ? Metabolic heat generated and number of persons making use of the chamber. ? The temperature of the external mine atmosphere to the chamber over the year and the influence of geothermal gradient on temperature at depth. ? The maximum internal chamber Apparent Temperature considered safe. ? The distance inside the underground mine and adjacent ventilation conditions.

Jan 1, 2012

By Walter E. Kramer

The advantages derived from the use of pellet burdens in blast furnaces are so great, that hematite ores are being converted into pellets in greater quantities each year. The conversion of these ores into pellets appears on the surface to be relatively simple. In reality, this is not so. Serious difficulties are encountered in drying these pellets that do not exist in the drying of taconite concentrate pellets. The ores that present problems are goethite and earthy hematites. Green pellets prepared from these ores have very law shock temperatures, 200-600° F. The shock temperature of a green pellet according to our definition is the highest initial temperature to which a green pellet may be exposed without suffering decrepitation. Decrepitation may involve spalling, fracturing or total disintegration. The poor shock properties of these green pellets result from the inability of the vaporized water to escape freely and easily as it is formed with¬out affecting the integrity of the pellet. As a consequence, the pellets must be carefully dried prior to induration. This careful treatment is costly. The slow drying process restricts productivity and requires larger furnaces than desired. The use of an additive to elevate the shock temperature of the green pellets would increase productivity. Bentonite is used in some pellet plants to improve balling but it raises the shock temperature only slightly. Nalco became interested in the shock temperature problem because of its activity in the development of organic pelletizing aids for taconite concentrates. The findings reported here are an outgrowth of our experimental work on the development of shock temperature additives.

Jan 1, 1967

By W. R. Junge

The investigation, selection, and implementation of remedial activities for large, complex mining and milling sites is dependent on the cost-effective management of tailing and waste materials. Site investigations evaluate the contaminant source areas, assess the potential release rate of contaminants, and determine the acceptable contaminant release rate for the site. Selection of appropriate remedial activities is based on evaluation of constructability, reliability, performance, effectiveness, permanence and cost. Remedial technologies available for tailing and waste material include removal, consolidation, capping and drainage control. Proper implementation and documentation of the selected remedial activities are critical to the overall success or failure of the remedial program. A step-by-step process, established at the initiation of a project, should accurately document all construction activities, monitor environmental conditions at the site, assess the performance of the remedial activities, and, ultimately certify that the remedial activities have met relevant and appropriate standards. Case histories are presented for a uranium mill at Uravan, Colorado and a lead, zinc mine at Gilman, Colorado. These case histories provide examples as to the combination of remedial technologies that have been applied at these specific sites.

Jan 1, 1989

By R. F. Hadley

Alluvial valley floors constitute a valuable land resource and have been important to ranching operations in semiarid western United States. This resource may be in jeopardy locally if the alluvial deposits are disturbed by surface mining of coal deposits. Erosion problems caused by poor land-use practices can cause trenching of the unconsolidated alluvium with a consequent lowering of the water table and depletion of soil moisture needed to support vegetation. Historical evidence of this sequence of events is abundant in geologic literature and serves as the basis for assessing potential impacts of surface mining. The potential geomorphic impacts of surface mining on alluvial valley floors with regard to fluvial processes are: (1) disruption of the longitudinal profile followed by valley trenching and high sediment yields downstream and (2) replacement of the excavated alluvium with unconsolidated material that does not have similar physical characteristics and may be susceptible to erosion. Mining may disrupt the existing hydrologic framework affecting streamflow, ground-water levels and water quality of both surface water and ground water. Although functional hydrologic and geomorphic processes are similar, each valley represents a complex environment that does not submit to broad generalizations.

Jan 1, 1978

By J. D. McKay

Flotation columns have been readily accepted for use in most sulfide flotation plants; however, recently columns are being used in many other areas. Recent improvements in design methodologies have overcome many operating problems and led to improvements in metallurgy. In addition, physical improvements in column design have simplified their operation while leading to better control. The Turbo-Air External Bubble Generator has provided a method for bubble size control and variation in air holdup and carrying capacity. These have enabled commercial operations to improve grades and recoveries by optimizing performance.

Jan 1, 1990

By M. Beale

Fuzzy logic and neural networks are new technologies being applied in many areas of engineering and business. While it is not always clear which kinds of problems are best suited to these technologies, and which problems are best approached with more standard methodologies, both fuzzy logic and neural networks appear to show great promise in the field of control systems. This paper demonstrates two advantages that these technologies offer: Easy controller design in the absence of a mathematical model of the plant to be controlled, and adaptive control capable of quickly responding to changes in the plant.

Jan 1, 1994

By Fengmei Chen, Na Liu, Bingrui Li

A quantitative analysis method based on the airflow influence factors is proposed to evaluate airflow stability and discriminate airflow directions in complex ventilation networks. The law governing the changes in airflow caused by changes in branch resistance is revealed based on simulations of the airflow state in a ventilation network and a statistical analysis of the results. Then, three evaluation indices (airflow sensitivity, airflow influence factor, and critical airflow) are determined, matrices of the airflow influence factors and critical airflows are constructed, and a quantitative evaluation method for ventilation system stability and an airflow directional discriminant are proposed. The results show that the stability of a ventilation system can be reliably evaluated based on the airflow influence factors. The sensitive branches and dominant branches in the ventilation network can be determined based on the matrix of airflow influence factors, and the reversed branches, the trigger branches, and the reversal conditions can be determined based on the critical airflow matrix and the matrix of airflow influence factors. The proposed airflow directional discriminant is suitable for evaluating arbitrarily complex networks.

Nov 15, 2023

By Edward S. Plotkin, Gary A. Almeraris, Thomas F. Peyton

The lining of the tunnel and shafts for a new section of New York City's- water system required extensive components to produce, deliver and place a continuous tunnel linning. The project placed approximately 153,000 CM (200,000 cy) of concrete for 5,340 M (17,520) of drill and blast 7.3 M (24 ft.) ID tunnel, located at depths of 152 M (500 ft.) to 213 M (700 ft.) . This section of tunnel will be connected to the surface water distribution system via four shafts of varying diameters ranging from 5.8 M (19 ft.) ID to 1.5 M (5 ft.) ID . All work was done beneath the streets of Manhattan under the rigid constraints of the City of New York and the Bureau of Water Supply regulations.

Jan 1, 1987

By Stephen D. Schwochow

Aggregate producers nationwide well recognize the numerous problems often faced in securing local approval to open and operate new gravel pits and rock quarries. Similar problems are faced in Colorado, but this region also presents certain political, social, and geological complexities that have become particularly troublesome in the last 10 years. The gravity of the local permitting dilemma can be related directly to the worsening supply-demand imbalance for aggregates in the state's most populated area, the Front Range urban corridor, particularly the Denver metropolitan area. The drive to develop crushed-rock reserves to supplement dwindling alluvial supplies and to meet increasing regional growth demands was somewhat predictable but perhaps more a "last resort" alternative forced onto producers by a hesitant and often apathetic government.

Jan 1, 1982

Energold Drilling Corp. is a leading specialty drilling company servicing the mineral and energy sectors in the Americas, Africa and Asia. Energold specializes in mineral exploration in remote locations with limited infrastructure. Such locations require the smallest footprint possible going in, leaving as little or no evidence on their way out. Energold?s rigs can be transported by helicopter or manually on footpaths as narrow as 1 m (3.3 ft). They set up quickly and then are struck and packed out, with any sign of their presence quickly disappearing behind them. Energold has teamed up with Atlas Copco and its team of engineers in North Bay, Ontario to design small rigs capable of drilling to a variety of depths, as required for each project.

Jan 1, 2013

By Stephen C. Moore

The Grossschloppen vein-uranium deposit, Bavaria, West Germany, was examined utilizing underground workings during 1980-82 by Esso Erz GMbH, an affiliate of Exxon Minerals Company (EMC). Geologic evaluation entailed dense drilling of a portion of the deposit from workings constructed specifically for the program. Discovered in 1977, the deposit was initially explored by surface diamond drillholes which allowed definition of a 30-60 m wide vein system discontinuously mineralized along a 1000 m strike length and to at least a 450 m depth. The underground program was conceived as a cost effective procedure to answer questions on vein correlation, grade continuity and variability. A 1200 m decline allowed access for detailed sampling of approximately 10% of the known area of mineralization. Fanned drillholes, logged by gaga probe, were spaced to provide intersections of veins at 10 to 20 m intervals. Six cross cuts also penetrate the pitchblende and uranophane mineralization which occurs in 0.1 to 2.5 as thick quartz veins. Detailed cross-sections and level plans were constructed for resource estimates of the intensively studied portion of the vein system. The program resulted in the discovery of local, high grade areas and an average grade in the evaluated area nearly double that expected from surface drilling.

Jan 1, 1983

By William Gleason

"With desert temperatures climbing high at Caterpillar’s Tinaja Hills Demonstration and Learning Center near Tucson, AZ in September, a group of editors were given a reprieve from the sun and stepped inside the new Cat Minestar Command Center. The movie theater-like temperatures inside were a welcome relief, and the computer screens stationed around the room were an indication of not just how much things have evolved in the mining equipment sector, but also a peek into the future of where mining is headed.Equipment manufacturers like Caterpillar have always had to deal with peaks and valleys in demand that come with mining, perhaps never more so than in the last five years. Sudhanshu Singh, global product manager for Caterpillar, said that in one month in 2012, at the height of the mining Super Cycle, Caterpillar produced more than 150 large mining trucks (haul trucks that carry 136 t/150 st or more). By contrast, Caterpillar produced about 80 of those trucks in the full year of 2016. Between 2012 and 2016, Caterpillar saw its profits drop by 40 percent.“This shows how cyclical the industry is, and it is a testament to the strength of Caterpillar to be able to tolerate the wide swings,” said Singh. Demand for commodities is once again on the rise as are commodity prices with many signs pointing toward a recovery for the mining sector, and Caterpillar has positioned itself for the recovery. During its 2017 press event in September, company officials emphasized that Caterpillar has added strength in its technology divisions by forming new partnerships and adjusting its operating plan.“At the heart of our enterprise strategy is the operating & execution (O&E) model, a strategic framework to identify areas of the business that either create or consume the most value,” said Caterpillar chief executive officer, Jim Umpleby. “Using the O&E model as a guide, we gain a deeper understanding of where we have a competitive advantage, which is key to generating high returns.”"

Jan 11, 2017

By Andrew Thomson, Peter Wright

"A section of a London Underground expanded segmental lined tunnel constructed in the 1970’s progressively deteriorated after 2001, with extensive radial joint spalling and mid-segment cracking. As part of the PPP contract Tube Lines Ltd and their partners carried out various analyses of the tunnel, including analysis of laser scans of the tunnel, geotechnical testing through the tunnel walls, geotechnical desk studies, real-time monitoring and even full-scale segment testing. This paper discusses the behaviour of the tunnel lining in this setting, the causes of failure and the lessons that can be learnt from this rare example of a tunnel which was progressively failing in service. It is finally noted that a replacement tunnel lining was installed during night-time possessions and completed in 2015. INTRODUCTION In 2003, Tube Lines Ltd. was established under a Public-Private Partnership (PPP) scheme to provide maintenance services and upgrade projects for London Underground (LU). The Deep Tube Tunnel Knowledge and Inspection Programme comprised the assessment of all tunnels, shafts and other underground structures. This included a number of lengths of tunnel constructed using segmental concrete linings. First used by LU in the 1960s, the savings both in cost and speed of construction led to concrete linings replacing cast iron for new tunnel construction in all but a few cases. During the initial scoping phase of this programme, inspections identified potential issues with the expanded concrete segmental linings on the Jubilee line. The inspections found a number of segments with surface spalling (Figure 1a), which did not appear on the post-construction defect records. These were generally relatively shallow, up to 40mm deep, spread over a wide area of segment. These were different to spalls caused by handling damage, which are typically localised at segment corners. Subsequent inspections over the following years identified an increasing number of segments with these types of spalls as well as an increased incidence of longitudinal mid-segment cracking (Figure 1b). The increasing occurrence of these defects was hypothesised to be caused by tensile stresses developing in the vicinity of the joint."

Jan 1, 2016

By P. C. Miller

The paper reports laboratory results from the bioleaching of chalcopyrite ores and concentrates using a mixed moderate thermophile culture. Copper dissolution in excess of 95% was achieved in all cases with the majority of tests indicating copper dissolution in excess of 98%. Aspects of downstream processing are discussed in relation to iron rejection by precipitation. The laboratory results indicate the need for careful control of the pH value to prevent co-precipitation of the copper with iron. A comparison of capital and operating costs is given indicating potential differences between the use of toll smelting and bacterial leaching on site. A discussion is given highlighting the sensitive cost areas of these two process routes.

Jan 1, 1997

By Andrew Kaczmarek

The mining industry is enjoying a much needed and long awaited increase in demand for natural resources. However, consolidations in the mining and mining service industries, along with a generational departure of experienced industry professionals, is challenging today’s mining companies. These challenges are not only in maintaining their existing operations, but also in securing qualified resources for developing new projects. These challenges are compounded for junior mining companies. They oftentimes lack for operating properties to draw experienced professionals from. Also, juniors have to compete with the majors’ “mega-projects” for experienced project personnel from the reduced ranks of engineering companies. This article discusses some strategies developed by Anatolia Minerals Development (Anatolia) in developing its Çöpler gold project in central Turkey.

Jan 1, 2006

By J. R. Riding

In situ solution mining of uranium has environ- mental advantages over conventional mining. The leaching of uranium, however, alters the groundwater quality in the aquifer where the mining occurs. Currently, regulations require that the groundwater be restored to approximately its original condition. This paper, a summary of a study funded by the Bureau of Mines, reviews the state of the art in restoring groundwater quality after in situ uranium leaching. Current restoration practices discussed include disposal of liquid wastes in deep disposal wells and evaporation ponds, producing from all wells during restoration, and recirculating water purified in surface plants. Methods for predicting the effectiveness and cost of current techniques are presented. Possible alternative techniques are also described. Two restoration operations are discussed.

Jan 1, 1979

By Georgene Renner, Chee Theng, William Gleason

"More than 6,300 people attended SME’s 2016 Annual Conference & Expo in Phoenix, AZ and many of them made the trip to the conference to take part in the excellent technical sessions that are presented on a yearly basis by the Society.Holding true to form, this year’s conference was full of options. In fact, this year there were 121 technical sessions and 751 presentations to chose from. The following is a sample of some of the technical sessions as seen through the eyes of the editors of Mining Engineering and SME technical papers.SME Sections Sharing Success: Changing thePublic Perception of MiningThis session was a workshop on how several local sections were effective in getting the message out to their communities and schools about the value of the extractive minerals industry. Several sections shared their outreach successes, including the Mining in Society merit badge activities by the Minnesota Section by Julie Lucas and SME’s participation in the World Scout Jamboree in Japan by Frank McAllister.Dan Alexander highlighted activities by the Pittsburgh Section, such as preparing minerals kits and pamphlets for elementary school classes and regional science fairs. The West Virginia University Student Chapter used the kits as handouts at their local gem and mineral show. School speakers in full mining gear were especially interesting to the young children.Other speakers were Michael Linn, Paradise Valley Unified School District — Business and School Partnerships; and Greg Kruse, Central Wyoming Section of SME — What makes a successful section?Engineering Competency ModelAmerican Association of Engineering Societies and the U.S. Department of Labor, with a grant from the United Engineering Foundation, developed a guide to the set of skills necessary for success in the engineering community -- Knowledge – Skills – Abilities — needed for all disciplines.Various engineering societies are now writing the Tier 5 occupation-specific requirements. The Competency Committee is charged to write concise and discipline-specific mining engineering, mineral processing engineering, geological engineering, and geophysical engineering by Sept. 30, 2017."

May 1, 2016

By Samuel M. Brock

Problems related to strip and auger coal mining have grown with the development of the industry and the economy. New technology has produced equipment that has made mining by surface methods not only highly productive, but potentially highly destructive of water resources and natural environments. On the other hand, growth of the economy has produced an increased demand for clean water, and created new demands for amenity values that natural environments provide. Thus, opposing forces have created conflicts in resource use. And these conflicts have made surface mining highly controversial. Resolving the controversy will require the solving of complex economic and social problems. The essence of the economic problem created by surface mining is that, in the absence of proper regulation, substantial costs resulting from the process are borne by the public rather than the mine operator.

Jan 1, 1968

By H. V. S. Tingley

My topic today is future trends in compensation for the mining industry. I seldom get the chance to speak about a subject of such immediate interest to an audience, so I would like to make the most of this opportunity by telling you that everybody in this room will become rich beyond his wildest dreams in the next few years. I would like to open my talk that way, but in compensation, like everything else, there is a great gap between dreams and reality. Back to reality. When we talk about compensation, we?d better define our terms because the compensation is really an umbrella for five basic types of payment made to management personnel. Slide 1 identifies these elements of compensation.

Jan 1, 1980