Search Documents

By W. Petruk

An investigation was conducted to determine the minimum number of samples that must be studied by image analysis of polished sections in order to characterize a mill product and to determine the apparent mineral liberation. It was found that a representive polished section cannot be prepared from an unscreened sample that has a wide size range of particles. Similarly individual screened' fractions are not representative of the sample because minerals are partitioned during screening. Consequently the quantities of soft brittle minerals are increased in fine grained fractions and quantities of hard minerals are increased in coarse grained fractions. It is assumed that results obtained by combining data for a series of narrow size range screened fractions (1 Tyler size range) are representative of the sample, and relatively accurate apparent mineral liberation data can be obtained for a mill product by analysing each fraction and combining the data. Somewhat less accurate data would be obtained by analysing a series of screened, fractions that have a wider size range of particles (5 Tyler size ranges). Mineral liberation analyses show that the most reliable apparent mineral liberation in each screened fraction is a value taken from a smooth curve drawn through the lowest points on a graph of % free vs size. A correlation between the apparent mineral liberation in screened fractions and calculated mineral liberations using Kings liberation model is good for sphalerite but not for chalcopyrite and galena.

Jan 1, 1985

By Marcel F. DeGuire

Pilot plant operations are described for the treatment of manganiferous zinc concentrates from the Gamsberg ore deposit in South Africa via conventional electrolytic zinc processing. Two methods were employed for the control of excess manganese ions in the pilot plant electrolyte involving (1) chemical oxidation and (2) anodic oxidation. The chemical oxidation method for manganese control was very successful. It also was found that the addition of manganese dioxide ore was not required for oxidation of ferrous iron during the neutral leach or jarosite precipitation steps. A new method (JAR process) for iron removal also was tested in the pilot plant.

Jan 1, 1978

Sinter mixes of three iron ore types were prepared with a range of water contents in a laboratory investigation. The mean diameter of the granulated mixes and the void fraction of beds of the mixes were determined experimentally. Pressure drop measurements over a range of flow rates were made in a laboratory permeameter with pressure tappings at several depths in the bed. The Ergun equation was applied to the results to determine the shape factor of the granulated mixes. The pressure readings down the bed were used to estimate the local void fraction in the bed using the Ergun equation and the calculated granule shape factors and it was found that there was a decrease in void fraction with depth in the bed. The significance of this and the variation of the shape factor values with the amount of water used for granulation is discussed in relation to the strength of granules of the sinter mixes.

Jan 1, 1984

By Iga Trisnawati, Fitria Puspita, Himawan Tri Bayu Murti Petrus, Gyan Prameswara, Idi Amin, Andi Nurfaadhilah Ulfah

Laterite ore is a valuable resource due to its high content of metals essential for modern technology, including nickel, iron, and cobalt. However, extracting nickel from laterite ores is challenging due to their complex mineral composition and low nickel concentrations. This study examined the leaching behavior of pre-roasted laterite ore and the effect of roasting on leaching kinetics. The ore was roasted at temperatures of 280°C and 610°C for 3 h, followed by sulfuric acid atmospheric leaching. The results demonstrated that pre-roasting at 610°C significantly enhanced nickel leaching recovery, with up to 93% nickel successfully recovered. The leaching process of pre-roasted laterite ore was found to be controlled by diffusion through the ash layer, with activation energy values of 20.97 and 18.97 kJ/mol for laterite roasted at 280°C and 610°C, respectively. These findings indicate that pre-roasting can improve the leaching performance of laterite ore, potentially leading to more efficient and sustainable nickel extraction processes.

Feb 27, 2024

By Gerrit V. R. Goodman, Fred N. Kissell

The issue of miner safety in case of an underground mine fire has been extensively examined by both government and industry. These efforts have intensified in recent years following a number of fatal fires at underground coal mines. As a result, there is an increasing interest in the reliability of coal mine escapeways during a mine fire. This paper discusses the use of fault tree analysis for evaluating escapeway reliability. A fault tree is developed using standard logic formulations. It is later evaluated using commercially available software. The computer model uses Boolean reduction to obtain the minimal cut sets and minimal path sets of the tree. A brief analysis is also conducted to determine the occurrence probability of the TOP event. This study shows that fault tree analysis is a viable means of analyzing escapeway reliability. The cut and path sets reveal those event sequences leading to fatalities. Such information is useful in safety training and accident prevention. The probability of the TOP event shows the frequency of occurrence for fatalities in an underground mine fire. The usefulness of this value, however, is limited by the accuracy of the data for the initiating events. For mining events, the data is difficult to estimate precisely.

Jan 1, 1989

By K. Chandrasekaran

Carbon-in-Leach (CIL) is conventionally used in gold processing operations when preg robbing components are present in the ore. CIL process is becoming attractive even in other situations when preg robbing is not a factor. This paper discusses the situations in which the CIL circuit can be applied. The results of Leach/CIP and CIL circuits at Newmont's Mill No.2, 4 and 5 are presented for comparison. Newmont's Mill No. 4 was initially designed for a throughput of 4500 tons per day. The mill is presently operating at an average throughput of 7300 tons per day without significant changes to the original design. The design considerations of the Mill No.4 CIL circuit are discussed.

Jan 1, 1991

By Steven M. Bishoff

The reclamation of surface land areas disturbed during the course of coal recovery became a major, universal consideration upon the implementation of the Surface Mining Control and Reclamation Act of 1977. This legislation not only established reclamation as an absolute requirement, but also presented guidelines for reclamation standards and required bond-posting procedures to assure completion of the reclamation process. The Office of Surface Mining was established to enforce the provisions of the Congressional mandate by promulgating specifically detailed regulations and supervising the State participation in this regulatory process. The major operational consequences of the reclamation-related provisions of the Act and the OSM regulations are the increased costs and complex procedures necessary to accommodate the regulatory authorities. It is anticipated that many of these costs and procedures have not been adequately evaluated by either the coal operators or the regulatory bodies. It is, therefore, necessary to proceed with an examination of the general reclamation processes, the effect of these processes on product costs, and the methods, if any, which may be utilized to minimize their impact on the overall operation.

Jan 1, 1981

By J. Villeneuve, M. A. Reute, E. Verhoe

The objective of EU waste policy is to reintroduce used materials into the economic cycle, especially by recycling, or to return them to the environment in a useful state or at least a harmless state. To support decision-making in complex systems, the standardised ISO 14040 life cycle assessment (LCA) method can be used to quantify and to interpret the environmental repercussions of (changes in) a product system from cradle to crave related to a functional service unit. The use of the standardised LCA method at European level can be characterised as a damage-oriented or top-down method, which is often used in product design. Winning, extraction and processing of metals are part of the interconnected worldwide metals production system linked to product design, manufacture and recycling. This complexity cannot be dealt with using LCA. This paper will discuss a dynamic model that deals with this complexity, at the same time providing detailed bottom-up insight into the complex web of materials referred to as Metal Ecology. An example on the replacement on lead in solders will be discussed to illustrate this.

Jan 1, 2005

By Paul D. Tomlingson

During the next several months, SME’s E-Newsletter will feature 15 articles on maintenance management. The articles may be read online or downloaded and distributed within your organization. They will address maintenance management topics, offer guidelines to mining managers and provide techniques that the maintenance manager can use. The articles will stress equipment management, a strategy that the mining industry has accepted as a modern replacement for outdated maintenance practices. Equipment management is the mutually supportive interaction of all mine departments as they establish equipment needs, procure equipment, test, commission, operate, maintain, modify and eventually replace equipment. The successful application of equipment management principles can quickly and reliably produce cost reduction and performance improvement results while providing a dependable way of sustaining them. Equipment management embraces modern management techniques. These include reliability-centered maintenance, life-cycle costing, capital performance, the effective use of information and productive organizational models.

Jan 1, 2003

By M. T. Ityokumbul

Concentrate flowrates have been measured for the flotation of -100 mesh Lower Kittaning coal in a computer controlled 0.076 m x 3.5 m pilot flotation column. The variables studied were recovery zone height), air flow rate, and solid feed concentration. The size distribution of concentrate and tailings samples were determined. The results obtained show that the concentrate flow rate was independent of collection zone height, but dependent on the gas flow rate, solid loading and particle size. New correlations for column carrying capacity and yield are provided as a function of these fundamental operational parameters.

Jan 1, 1997

By H. B. Charmbury

The acid mine drainage problem in Pennsylvania is of continuing and growing interest to the coal mining industry, the state government and the citizenry at large. Approximately one-third of the total volume of mine drainage presently polluting the streams of the Commonwealth originates from active coal operations and two-thirds come from ?abandoned mine discharges.? For this reason the Pennsylvania Department of Mines and Mineral Industries has mounted a significant research and action program seeking solutions to this two-fold problem. The Coal Research Board of the Department has sponsored a wide variety of research projects in an effort to study the treatment of acidic and highly ferruginous mine waters. A review of the published literature on the treatment of mine waters indicated that many laboratory and theoretical studies had been undertaken on various aspects of the coal mine drainage problem, but little applied, developmental, or engineering study had been undertaken. In January of 1964 the Board commenced a rigorous program using state and industry funds in an effort to find a ?least cost? solution or solutions to this vexing problem.

Jan 1, 1967

General. Data for the operating information given in the 15 tables in this chapter was obtained from voluminous questionnaires sent to over 100 operating companies in 1972. There has been a considera¬ble change since then in supply and power costs and many companies have had expansions or revisions since that time, so it must be realized that information is valid for the year 1972. This is true except for the three new properties of Sacaton, Metcalf, and Pinto Valley. These three operations started up since 1972 and all information for them was obtained in 1975. The questionnaires were sent to all major copper properties throughout the world as well as to many smaller units and to some mines that had complex or unusual conditions. Properties for which no information is given did not submit completed questionnaires. Several operations were unable to supply information requested be¬cause of company policy prohibiting it. However, data is presented for 75 different operating properties. The reference number of the left-hand column is the same for all 15 tables of data. If the company had several operating properties as of 1972, then subsequent properties use the same number but a different letter. For example, Anaconda's property at Butte, Mont., is IA, whereas Anaconda's (now Anamax) Twin Buttes property in Arizona is IB. Table I gives general data for the properties including exact loca¬tion, milling rate, pertinent assay values and recoveries, and a brief listing of ore and gangue minerals. It was not possible to obtain any more information from the properties in Chile except that given in Table I. Crushing. Crushing plant operating data is given in Table 2. This table gives data on the crushers, feeders, and screens used at each property. The data obtained on feeders was confusing, but, rather than completely eliminate this information, it was decided to report it as given. The confusion lies only in the description of where the feeder is located. Where a primary feeder is listed it was not possible to determine if this feeder was on primary feed or primary discharge. For secondary feeders it is known that the feeder listed usually is feeding the secondary crushers, but at some properties it is handling the secondary crusher discharge. The same reasoning holds true for tertiary feeders-they handle either tertiary feed or discharge. This table contains a voluminous amount of data. A column giving tons per day per square foot of screen area would have been very informative, but some properties included circulating load in the feed rate and others listed new feed only, so calculations were meaningless. Autogenous Mills. The use of autogenous or semiautogenous mills for any property must be given serious consideration in the future. Table 3 lists data for four properties that are fully autogenous and four more semiautogenous mills that use balls to supplement the chunks of ore. This method of grinding is especially applicable when the ore is of such a nature that crushing problems would be severe, such as when ore is wet or sticky or contains a lot of fines. Paradoxically, it should also be considered when ore is tough and hard and blocky because then the competency of the ore means it can serve well as the grinding media. Where the ore varies greatly in hardness, as at Cyprus Pima and Lornex, semiautogenous grinding has been especially beneficial with capital costs and operating costs both 10-20% lower than could be obtained with conventional crushing and grinding. Rod Mills. For a great many years the standard milling operation used two- or three-stage crushing followed by open circuit rod mills and then ball mills in closed circuit with classifiers of some kind. A surprising number of properties crush to the fine size of about 3/8 in. and then use ball mills only, in closed circuit, with no rod mills. It is difficult to say whether rod mill-ball mill circuits or ball mill only is the best. One can be certain of two things: (1) the argument will go on for a long time and (2) for some mills one method obviously was superior over the other. As ball mills of 14, 15 ft, and larger came into use, more properties like Duval Sierrita (16b ft diam by 19 ft long) and Bougainville (18 x 21 ft) were built with single-stage ball mill grinding. Although there are larger rod mills used, especially in the iron ore industry, the largest rod mills on copper ore are at Twin Buttes (14 x 18.5 ft) and at Gibraltar (13'A x 20 ft). Table 4 lists operating data for rod mills. If a company is listed in Table I

Jan 1, 1985

By Paul C. Miclea, Robert E. Murphy

The behavior of fire and airflows in a confined tunnel differ significantly from more familiar fire situations outside, due to the buoyant effect which tends to create a layer of hot smoke and gases flowing away from the fire near the crown of the tunnel, while air supporting combustion moves toward the fire beneath the smoke layer. A subway emergency ventilation system is designed to force air to flow through the tunnel, shifting the balance of heated air in the direction of the forced flow and avoiding the "back-layering" of hot gases and fumes. This paper presents a computer program, called the "Subway Environment Simulation" (SES), which can be used to predict airflows created by the emergency ventilation system. It utilizes the latest state-of-the-art analytical treatment of fires in enclosed spaces, including observations from mine fires and gas explosions. The program allows designers to reduce construction cost by identifying unnecessary ventilation shafts and by verifying fan capacities. In addition, the program allows the designers and operators to determine safe evacuation routes, in case of a train fire, by predicting the occurrence of back-layering. It can be used to determine when the ventilation system can control the direction of smoke movement to provide a clear and safe path for evacuating people and facilitate fire fighting operations.

Jan 1, 1989

By J. S. Gardner

Fortunately, few mining professionals have dealt with what all mining professionals fear---a mine disaster. Unfortunately, many have dealt with ?accidents? which may or may not claim lives but nevertheless rise to the level of a ?disaster? given the fallout of liability and litigation in today?s society.1 The undersigned authors published an article some ten years ago regarding crisis management2 based upon their collective first-hand experiences in actual disasters to that point in history. Unfortunately, disasters have occurred since that time, prompting legislation, and a fresh analysis and expansion of those basic principles is certainly in order. Without question, no two disasters are ever alike, yet general guidelines for forming an effective plan of action can be formulated?and if a mining operation is to have any chance of survival after a disaster, such a plan is vital. The primary concern as any disaster evolves remains as stated a 2003 SME article3--the protection of human life. From that point, the focus moves to any assistance that may be needed given the magnitude of the situation. Permeating throughout this process is "damage control." The first step in dealing with a disaster, however, begins long before any threat of danger arises?formulation and implementation of an Emergency Response Plan.

Feb 23, 2014

By Güldane Atesoglu, İsmail Atilgan

The changes in the elemental contents and the structural properties of chalcopyrite concentrate when roasted were studied, and the main reactions contributing to the leaching process revisited. Firstly, TG/DTA measurements were performed to identify the roasting temperatures that influenced the type of species reacting with sulphuric acid leaching liquor. The temperatures of main reactions, whose output may affect the subsequent leaching process, were analysed for the concentrate at hand, and concluded to be generally lower than those reported in literature. Secondly, the obtained results were confirmed by images and XRD measurements on the roasted concentrate at temperatures in between 350 and 600 °C with increments of 50 °C. Finally, the leaching behaviour of the roasted specimens in a stirred sulphuric acid solution examined and the Cu/ Fe selectivity investigated that the maximum Cu/Fe ratio in the pregnant solution would nearly be achieved for the roasting temperatures lower than 500 °C, since the oxidation temperature of iron sulphate is found lower than that of copper sulphate.

Aug 11, 2022

By Horace M. Varner

Under sponsorship of the USBM and later of the DOE, a new type of rotary rock drill has been developed by The Bendix Corporation. Originally developed for the production of holes for the installation of longer than seam height roof bolts, the flexible drill is a useful tool for many drilling applications. This drill allows hands-off or remote production of holes for increased drilling speed and greater operator safety in any strata suitable for rotary drilling. The paper discusses various applications and experience for the flexible drill system in coal mining, metal/nonmetal mining, and for general civil engineering uses. Manual, remote control, and automatic roof bolter modules are also discussed.

Jan 1, 1982

By Lyman H. Hart

Michiquillay is a major copper deposit situated about 70 km (44 miles) northeast of Cajamarca in northern Peru (Fig. 1). It occurs largely in quartz monzonite in a shatter zone produced by the intersection of northwest- and northeast-trending fault systems. The geology is described by Hollister and Sirvas (1974). The ore deposit was drilled in 1963-1964 by Asarco, with results indicating a resource of 575 Mt (634 million st) averaging 0.72% Cu-0.03% Mo. A decision to bring the project to production has been deferred because world capacity to produce copper has been more than adequate to serve world requirements since 1964. The chain of events leading to the discovery of Michiquillay was set in motion by a decision by the management responsible for the Chilete mine to undertake an investigation of the surrounding area for a possible supplementary source of mill feed to bolster its decreasing lead-zinc reserves. Chilete, located 100 km (62 miles) inland from Pacasmayo, is the most northerly, important mining project in Peru, and little was known of the mineral potential north and east of that point. Relatively unimpressive reports of Colonial silver mining had attracted little investigation, and little was known of the regional geology. One study by Benavides (1956) had been made of the Cretaceous in the region of Cajamarca.

Jan 1, 1991

By G. Sciocchetti, G. F. Clemente, F. Scacco

INTRODUCTION Radon, thoron and their airborne daughter products may result in a significant biological hazard when they are concentrated in enclosed places such as mines, houses and caves. High concentrations of radon and its particulate daughter have long, been known to be a causative agent for lung cancer to uranium miner: (Archer 1973). More recently increasing concern has been expressed on the possible health hazards associated with long term exposures over large population groups to low levels of radon daughters (Cohen 1980, Stranden 1980). Due to its peculiar geological features, Italy has various natural environments where the content of uranium and thorium in the soil may increase underground radioactivity. The presence in Italy of many underground waters rich in radon may be considered a further important source of radon in underground mines. A preliminary survey of the radon and radon daughter air concentrations in italian underground mines was started in 1971 (Bottino 1973). Furthermore many studies (Sciocchetti 1978, Sciocchetti 1980, Clemente 1980) have been performed during the last ten year to characterize the natural radiation environment in Italy. It has been also demonstrated that 21OPb/21OPo skeletal burden in spa workers and non-uranium miners can be heavily increased by the exposure (short or/and prolonged) to high levels of radon daughter air concentration (Clemente 1980). All these studies have been of great help to put in the right prospective the radiation hazards linked to the underground working activity in non-uranium italian mines. Two main actions have been prosecuted from 1971 until today in order to evaluate in greater detail such radiation hazards and then, when needed, to obtain their reduction to levels which may be considered acceptable. The two actions may schematically described as the following: - Measurement of the radon and daughter (and thoron and daughter when needed) concentrations in most of the italian non-uranium mines. The assessment of the radiation hazards linked to both the annual average lung exposure and the 210 Pb - 210 Po annual average dose to the skeleton is then performed for each considered mine by taking into account the main parameters characteristic of the mine. - Set up of a national regulatory recommendation on the permissible limits for the radiation exposure of workers due to underground mining activity. Such recommendation have been established in 1978 and have been designed in order to implement a national radiation protection practice during the underground mining activity. In this paper a summary description of the results obtained during the execution of these two actions will be given. MATERIAL AND METHODS Measurement of Radon, Thoron and their Daughter Products The excution of the planned survey requires the availability of specific techniques and instruments for measuring the different parameters characterizing the radon, thoron and their daughter exposure in mines. A reference laboratory was set up for the development and the standardization of the measurement procedures. Measurements of radon, thoron and daughter concentrations are performed by various methods: instanteneous or grab sampling methods and continuous read out monitors. The radon concentration is usually measured by a modified version of the two filter method. Mine air is drawn into a polyethylene bag and the sample is there after injected into a two filter tube; after sampling the exit filter is counted by the alpha spectrometric technique. The measurements is completed in a total time of less than 25 minutes at a sensitivity level as low as 3.7 Bq/m3 for a tube volume of 15 1. The measurement of radon and thoron daughter concentration and of the relevant potential alpha energy concentration is performed by means of a portable spectrometric apparatus which was developed at our laboratory (Sciocchetti 1981). The device allows multiple operating modes: instantaneous or brief sampling period and automatic cycles; computer data processing is then provided. The instruments that measure continuously radon concentration over long periods of time are of two types: a continuous scintillation monitor and an automated two filter

Jan 1, 1981

By B. K. Slone

The depth at which it becomes more economical to use slope access as opposed to box-cut access for near-surface coal reserves, termed "transition depth," can be established for a given coal property by considering cost estimates for those parameters that determine respective access method. Fourteen parameters that influence access cost were identified and ranges determined. A Transition Depth Formula was developed to permit determination of the better method of accessing a reserve, given such information as highwall slope, road width, total bench width, pit dimensions, road grade, belt component costs, pumping costs, and cost of overburden removal and reclamation. In most cases, in Appalachia, studies indicate that the transition depth ranges between 20 and 30 m.

Jan 1, 1998

By L. Barry Phelps

The application of an open-pit Materials Handling Simulator (OPMHS) to analyze mine planning and scheduling problems in large surface mines is discussed. The mine chosen for this application employed a large stripping dragline working in tandem with a shovel-truck haulback system for removing overburden. Large bottom-dump trucks were employed behind a coal loading shovel to transport the exposed coal out of the pit. Specifically, the current operations and the recommendations for short term and long term improvements were simulated on OPMHS. The effects of changing the operating parameters of the equipment on the total system were evaluated. Several alternatives were also studied for the best use of the existing equipment if the current operating parameters could not be improved upon. The results of the application are discussed.

Jan 1, 1978