Search Documents

By Richard Campbell, MEHMET KIZIL, Ismet Canbulat, Serkan Saydam

The design and effectiveness of ground consolidation to regain stability of longwall faces vary widely and are often based predominantly on-site precedence or what were considered successful applications at other sites in similar situations. Little is known regarding product migration characteristics or change in rockmass conditions as a result of the application of consolidation chemicals. This paper presents the in-situ testing rationale designed and implemented recently across several longwall operations in the Bowen Basin, Queensland, Australia to provide quantitative measurement of the actual zone of influence of various resin injection products. Product migra- tion was physically measured by monitoring the change in rockmass temperature as a result of the exothermic chemical reaction of the various strata consolidation chemicals used. In conjunction with strata coring and Lugeon transmissivity testing pre- and post-injection to characterise the improvement in rockmass conditions due to consolidation product injection. The results of the testing programme, migration measurements, and rockmass assessment are presented, along with a discussion on how site- based Rock Mechanics Engineers can incorporate the data into the design of strata consolidation plans.

Jun 25, 2024

By J. H. van Laar, C. S. L. Schutte, M. Le Roux

Highly energy-intensive systems prone to wastage are significant causes of unnecessary energy losses in industry. Deep-level mine chilled water reticulation systems fall within this category of inefficient energy-intensive systems. Some techniques (measured baselining, zero-waste baselining, leak detection, and control valves) exist to identify and reduce wastage in mine water reticulation systems. However, these techniques have not been compared, which begs the question of which is more accurate. A need, therefore, exists to compare these methods to determine the effectiveness of each. This study investigates each method and applies them to a case study mine, providing a platform for comparison. These methods identified wastage ranging between 2 and 20 l/s (3–30% of water consumption). The comparative effectiveness of the methods from best to worst was found to be zero-waste baselining, leak detection, control valves, then measure baselining. This study proposes an application procedure combining the considered methods to identify and eliminate wastage on deep-level mine systems more efficiently.

Jan 31, 2024

By Neel Gupta, Brijes Mishra

Coal mining activity disturbs the natural equilibrium of in situ stress state such that the induced stresses deform the surrounding rock mass. Although the installation of roof supports typically prevents rock deformation, rock mass failure may still occur in bolted roof. The erratic failure of rock mass after few days to months and years of excavation is the result of time-dependent deformation of roof rock under constant surrounding stresses. In the current research, the triaxial laboratory creep experiments proved that Marcellus shale exhibits time-dependent deformation under constant stress that was smaller than the failure strength. However, unlike conventional experimental results, the time-dependent deformation did not depend on the level of constant stress. The often-neglected initial state of specimens and intrinsic heterogeneity highly influenced the time-dependent failure of Marcellus shale.

Jul 27, 2021

By S. Potgieter-Vermaak, T. T. Chiweshe, W. Purcell

Complete isolation of chromium (III) from the reference material (SARM 131), Upper Group 2 (UG2) chromite ore, and Merensky Reef mineral ore was achieved using ammonium phosphate salt as flux. Optimum pH (3.2–3.8) conditions and sample to flux ratios (1:25) were some of the factors that were critical for the complete isolation of chromium. Increasing the sample to flux ratio (1:50 excess) however resulted in the conversion of all the elements in the melt into a green solution (pH, 5.8–6.7). A different chromium compound was subsequently isolated from the green solution by allowing this solution to stand in an open vessel in a cupboard for a month during which time the pH decreased to pH 3.5–4.2. Quantitative analyses of chromium from the isolated precipitates of SARM 131, UG2 chromite ore, and Merensky Reef mineral ore indicated chromium contents of 41.87, 60.41, and 23.93% respectively which were very close to the chromium content in the original samples. Analysis of the chromium precipitates using IR indicated the presence of phosphates (1100–1200 cm−1 ) while SEM-EDX analysis showed the presence of microscopic crystalline particles with Cr, P, and O as the major elements. Further characterization of the chromium precipitates using XRD and Raman successfully identified the product as chromium (III) metaphosphate C-type (Cr(PO3)3, JCPDS no. 01-077-0672), in the isolated chromium precipitates.

By Fernando Jorge Dick

Artificial sulphides have been produced on the surfaces of heavy metal-oxide, minerals at elevated temperatures (1) and these sulphides gave consistently similar flotation characteristics as the respective natural sulphides. In the case of tin, the only natural tin sulphide known is herzembergite (SnS) which is found only in minor quantities, and its flotation behavior is not known. Balberyszki, Dorenfeld, and Carmi reported (2) tests with artificial tin oxide and pure cassiterite treated with hydrogen sulphide at temperatures above 750oc. They confirmed that the product could be floated in acid pulps. However, iron sulphides derived from pyrite, limonite, and hematite which are generally the major impurities in tin bearing ores could not be separated from tin sulphides under the conditions used by previous investigators. As a practical matter, if complex tin ores or complex low grade tin concentrates are to be treated by this process, it is necessary to be able to separate sulphidized cassiterite from other sulphidized minerals in the feed. The major metallic minerals, by weight, in complex tin ores are the iron minerals--pyrite, hematite, limonite, magnetite and pyrrhotite. These minerals become (or remain) sulphidized during the sulphidization process.

Jan 1, 1978

By Michael J. Mujadin

Since the late 60's, planners at American Natural have known that natural gas supplies from traditional sources will be insufficient to maintain a consistently high level of service in the near future. This dwindling of traditional gas reserves will force American Natural and other gas companies to seek new and more exotic sources of supply. In recent years a number of alternative supply sources were considered, including arctic gas, LNG, and SNG based on naptha, LPG and coal feedstocks. Several combinations, all of which included SNG from coal were selected as the most suitable alternative sources of gas supply for American Natural, and thus our company embarked on the formation of a coal gasification project in the early 70's. Work began with the evaluation of available coal supplies in the United States in late 1970. Western North Dakota was selected for several reasons: large contiguous reserves of lignite were available near the surface, similar to German brown coal for which the Lurgi gasification process was originally developed; the conditions for land reclamation in the area are favorable; and the people in the area have a positive attitude toward well ordered development.

Jan 1, 1977

By Joseph M. Zigich

The Anaconda Minerals Company operates a molybdenite and copper producing mine and mill facility near Tonopah, Nevada. Included with the milling facility is a ferric chloride leach plant for removal of copper mineralization from the molybdenite concentrates. Discussed are the engineering and construction schedules associated with the leach plant. The chemistry associated with the process along with a description of the process flow, equipment, and operating parameters are contained in the paper.

Jan 1, 1983

By Michael J. Friedel

The scale-dependent hydraulic properties in a fractured porphyry copper oxide deposit are investigated for relevance to in situ leach mine (ISLM) design. In most well field designs, mine operators assume that hydraulic properties represent a continuous spatial function, or continuum. The problem, however, is that the representative elemental volume, the volume over which hydraulic properties are described as a continuum, is a domain (if it exists) that occurs between end members representing varying degrees of heterogeneity. At the Cyprus Cas a Grande mine, transmissivity fluctuations are spatially correlated suggesting that at the scale of ISLM, the hydraulic process is heterogeneous and a typical continuum representation is inappropriate for design. Alternatively, a conditional stochastic approach using the simulated annealing (SA) technique is deemed useful for the imaging of heterogeneous hydraulic properties. Specifically, SA preserves transmissivity extremes and spatial complexity, both necessary for accurate conditioning of a flow simulator. Also, the stochastic continuum approach provides an avenue whereby uncertainty (or risk) may be addressed. Currently, the SA weaknesses are that it is computationally time consuming, and uncertainty may increase when simulating under conditions of statistical isotropy. Recognizing that ISLM exerts a dynamic influence on hydraulic properties with time, the mine design should be reevaluated at intervals throughout the evolution of the leaching process.

Jan 1, 1993

By K. V. Raj

As open pit mines continues to grow deeper, managing air pollution can become challenging. During arctic air inversion, the temperature of the air over the mine increases with altitude, and the cold, heavy, surface air is trapped in the pit. This problem is complex, and any solution will require an extensive understanding of the interactions between the aerodynamic movement of air, air inversion, meteorology, pollutant sources, and transport phenomena in the open pit mines. The availability of computational fluid dynamics (CFD) has elucidated the pollutant flow mechanism in open pit mines. Very few CFD studies have been published, especially the Large Eddy Simulation (LES), on the contaminant transport in deep open pit mines under arctic air inversion. The contaminant transport in an open pit mine under arctic inversion is due to a stable or nocturnal boundary layer in micro-meteorological terms. Understanding the physics of the stable boundary layer (SBL) is relevant to air flow and pollutant transport in deep open pit mines. This paper focuses on a Large Eddy Simulation (WMLES as Sub-Grid Scale Model) modeling of the SBL and pollutant transport in a large open pit mine.

Feb 23, 2014

By T. S. Govindan

The first step in energy conservation in any industrial plant involves implementing many of the day-to-day "house-keeping" items such as fixing leaks, turning out lights, etc. When this step has been accomplished, additional opportunities require a detailed analysis of the energy systems, evaluation of risks and costs, and assignment of priorities. Examples of conservation schemes drawn from the experience of Du pont's Energy Management Consulting Services will be discussed. The utility of heat balances for kilns and dryers in minerals processing will be outlined. The inputs needed from Management for the success of conservation efforts will be discussed.

Jan 1, 1978

By R. W. Culbertson

During the 1920's, approximately 11,000 small gasifiers were in operation in the United States. They converted about 15 million tons of coal per year into low Btu gas. In some cases, hot raw gas was used for applications such as firing open hearth furnaces or brick kilns. In other cases the gases produced in the gasifiers were cooled, cleaned and desulfurized for various utility and industrial purposes. The steel industry was by far the largest user. The most important fact was that the conversion of coal to a usable fuel gas was demonstrated to be commercial. During the late 1940's and early 1950's, this form of energy was largely replaced by natural gas as the pipeline net work was expanded. Producer gas was no longer economically competitive. Over the past twenty-five (25) years, government controls on the interstate price of natural gas have maintained this situation. At present only three commercial small coal gasifier plants are still in operation in the United States. These facilities are operated by the Glen-Gery Corporation which is located in eastern Pennsylvania; the National Lime and Stone Company which is located at Carey Ohio; and Holston Defense Corporation which is located at Kingsport, Tennessee. There are, however, numerous operating gasifiers in other parts of the world. Recent events indicate that this situation is changing. The quantity of domestic natural gas available to the interstate market has been declining at the same time that demand for all forms of energy has been increasing. The current potential market for gas with a heating value ranging from 100 to 500 Btu per cubic feet has been estimated at sixteen (16) quads (16 x 1015 Btu) per year. This is expected to grow to twenty (20) quads by the year 2000.

Jan 1, 1978

By Roger Storry, Arnaud Hochart, David Harris, Olivier Martin

"INTRODUCTIONThe Port of Miami Tunnel (POMT), designed and constructed by Bouygues Civil Works Florida between 2009 and 2014, was a Public Private Partnership between the Miami Access Tunnel Concessionaire, Florida Department of Transport, Miami-Dade County and the City of Miami. The project comprises dual 11.3m internal diameter, 1.27km long, twin lane road tunnels running between Watson and Dodge islands under the main shipping channel in Biscayne Bay. Five cross passages (CPs), spaced at 200m centre to centre, provide emergency access between the two tunnels, as shown in Figure 1.The CPs were constructed by open-face excavation methods but the particular geological conditions at the project site (loose and variable carbonate sedimentary strata with very high permeability) required specific ground treatment solutions to provide safe excavation conditions and to ensure the long term serviceability of the permanent works construction. Where access allowed, ground treatment was performed from the ground surface using deep-mixing techniques; however, at two locations (CP2 and CP3) surface access was restricted and ground treatment by freezing, performed from the tunnels, was required. The CPs are 12.3m long with an excavation diameter of 5.8m and are located up to 30m below the water table partly or wholly within the Key Largo limestone (termed Layer S7 in the ground model). Layer S7 is a coralline limestone having a metastable honeycomb structure and high variable porosity. At CP2 the upper portion of the excavation was within the overlying Anastasia Formation limestone (Layer S6), comprising a highly permeable coquina. The geological profile along the project is shown in Figure 2.This paper presents aspects of the freeze design and the risk mitigation necessary to successfully achieve the construction of the CPs in the unique geological conditions."

Jan 1, 2016

By L. O’Connor, E. Tarshizi

The objective of this work is to provide a detailed review and a list of references in chronological order, comprising 80 recent technical papers, on the use of discrete-event simulation (DES) modeling in mining engineering. In this article, the review papers of published mine simulation projects through 2007 are summarized, and then a comprehensive review of individual articles published from 2008 to 2015 is presented. This survey work also includes analyses of the simulation tools used in the published projects, mining types and applications in order to assess these key features and evaluate the recent state of research in mine DES simulation. In addition, an interactive map visualization for the locations of the simulated projects is made available on a website to benefit current and prospective scholars in the field. The results of this investigation revealed that the most common application of DES in mining had been mining equipment selection and analysis, while ore processing and risk management projects were less frequently reported. The results also showed that modeling surface mines were in the majority, but the trend of publications for underground mine simulations had also increased. According to the results, ARENA was the most popular simulation software package, but several simulation tools that were only used once or twice in the mining projects are also included in this review.

Jan 1, 2018

By L. O’Connor, E. Tarshizi

The objective of this work is to provide a detailed review and a list of references in chronological order, comprising 80 recent technical papers, on the use of discrete-event simulation (DES) modeling in mining engineering. In this article, the review papers of published mine simulation projects through 2007 are summarized, and then a comprehensive review of individual articles published from 2008 to 2015 is presented. This survey work also includes analyses of the simulation tools used in the published projects, mining types and applications in order to assess these key features and evaluate the recent state of research in mine DES simulation. In addition, an interactive map visualization for the locations of the simulated projects is made available on a website to benefit current and prospective scholars in the field. The results of this investigation revealed that the most common application of DES in mining had been mining equipment selection and analysis, while ore processing and risk management projects were less frequently reported. The results also showed that modeling surface mines were in the majority, but the trend of publications for underground mine simulations had also increased. According to the results, ARENA was the most popular simulation software package, but several simulation tools that were only used once or twice in the mining projects are also included in this review.

Jan 1, 2017

By D. L. Whiting

Dump leaching and ,in-situ solution mining have received considerable attention during the past few years due to their apparent economic viability and minimal environmental impact. Solution mining actually dates back to the 17th century when leaching of copper ore was first reported. However-, modern day leaching didn't begin on a wide scale until the mid-1900's. In-situ mining for copper, nickel, salts, and oil shale is currently looking more attractive as the technology advances. Presently, about 15 percent of the copper production in the United States is from leaching operations at approximately 14 active sites, the largest of which are the waste dumps near the Bingham Copper Mine, Utah. To establish a common background, the discussion is centered around state-of-the-art conditions. For dump leaching, complications inherent to the physical conditions and chemical reactions such as channeling, porosity and permeability, sorption, air flow, rock alteration and pH control are discussed. Emphasis is made on those conditions which render solution recovery rates and solution mineral concentrations unpredictable. By illustrating typical and actual field conditions, the generally accepted flow theories for both dump leaching and in-situ solution mining, including rubblization, are presented. For in-situ mining, hydrogeologic techniques such as geophysical well logging, aquifer testing and digital computer modeling are also discussed. The importance of artificial fracturing and well stimulating to solution injection and recovery is made with regard to project development. Finally, the subject of water pollution control techniques and the potential impact of the

Jan 1, 1977

By SHANTAE LEE, ELAHEH TALEBI, Frank A. Drews, W. Pratt Rogers

Fatigue in mining operations is a serious issue and a significant contributor to incidents and accidents. While mine operators are using or introducing new technology to monitor operator fatigue, there is little work that focuses on the subjective experience of fatigue and the use of fatigue monitoring technology. To investigate this issue, eight focus groups with a total of 44 operators of heavy haulage equipment working for two mining companies in the Mountain West of the USA participated in 1-h focus groups. The topic of the focus groups was the experience of operator fatigue and issues surrounding fatigue at the workplace. The results of the content analyses suggest that operators are well aware of the signs of fatigue, and that they understand the severity of these signs as well. In addition, they are aware of the effect of fatigue on driving performance and are using a wide range of methods to manage fatigue. Finally, based on participants’ assessment, current fatigue monitoring systems lack face validity and reliability and are perceived as not being effective. The results of this study emphasize the importance of a socio-technical systems perspective in the context of miner health and safety management. Only such a comprehensive perspective can result in improvements that are sustainable.

Jun 17, 2020

By B. A. Filas, H. N. Lammers

Responsible environmental, social, and governance (ESG) practices are not new to mining. It is the ESG acronym that has become the “flavor-of-the-day” with the stock markets, accounting firms, and investment strategists. This increased interest from the financial sector has heightened executive awareness and accountability to where corporate leadership and directors are proactively prioritizing ESG issues from the top down within their companies. This paper aims to convey what the authors believe one needs to know to be able to conduct and prepare effective ESG audits and reports. The emphasis is on how ESG fits within the mining sector, some of the ways that many mining companies have been practicing ESG responsibility for decades, the importance of effective communications with stakeholders, and the roles that regulatory and international lending institutions play in enhancing ESG practice on a global scale as a precursor to the discussion on ESG auditing and reporting. Without this background, the ESG audit may become a purely academic exercise.

Feb 1, 2023

By John W. Barnes

In seeking cost reductions, control methods are a fertile field because they significantly affect labor and other costs. While process control in uranium mills is excellent by the evidence of high recovery, the costs seem high to those familiar with extractive operations for other metals. To some extent this high cost is inevitable, because of exacting quality control-, the technically complicated recovery processes; poor control over grade and nature of mill feed- special problems arising out of the radioactive property of the material. Practices used in uranium mills and the limitations indicated for instrumentation and automation are discussed. It is concluded that any large investment in automatic controls should be preceded by a careful study of their reliability and maintainability, and an estimate of the net income after taxes smaller plants my find it more profitable, or at least less risky, to concentrate their efforts on the possible reduction of some control problems and to development of a stable force of skilled employees. The observed experience does not inspire optimism that ore-dressing plants can be extensively automated although certain unit operations offer a challenge for improvements in instrumentation and machine design.

Jan 1, 1960

By Adrian C. Dorenfeld

The lesser developed countries (LDC's) may be classified into two categories: 1) oil producers, and 2) non-oil producers. The non-oil producing LDC's, as a class, are at present in very difficult financial straits. (1) Since the quadrupling of world market crude oil prices in 1972, an ever greater share of the LDC's export earnings have gone to pay for oil imports, in-stead of national reinvestment. The LDC's inter-national debts--much of it to pay for oil--have soared to record levels, with consequent limits for future credits. (1) Again, this inhibits future national investments, and there does not seem to be an end to the future increase of Organization of Petroleum Exporting Countries (OPEC) prices. Indeed, some of the economic difficulties in some metal markets--particularly the imbalance of production vs. markets for copper, can be traced indirectly to the OPEC cartels' heavy-handed impact on copper producing LDC's which must produce copper at any price to meet their oil bills. (2) Among the major oil importing LDC's are the Philippines and South Korea. 50th nations have substantial cement industries. The South Korean industry is geared for major export markets in the Far East. Both nations have ambitious plans for economic growth in order to accommodate burgeoning populations with ever increasing expectations for high standards of living. These plans had some success, more or less, until the high OPEC oil cartel charges had to be borne. Now, in common with all oil-deficit areas, the Philippines and South Korea are seeking lower cost sources of energy. Both countries have coal deposits. In the case of the Philippines, the reserves are in scattered, relatively small deposits. Most of the coal deposits are faulted, folded and, in general present formidable production problems for limited reserves. Nonetheless production has been on the order of about 70,000 to 150,000 tons per year in the last 30 years. Prior productions (1920-1941) varied between 9,000 Co 150,000 tons per year. (13)

Jan 1, 1978

By W. V. Bluck

Higher coal quality is being recognized in potentially lowering the cost of power as measured at the bus bar. Assessment of potential coal supplies for most any given power plant is now going beyond buying at the lowest delivered fuel cost and is now taking into consideration other factors such as handling, storage, pulverization cost, boiler fouling, post combustion cleanup, and waste disposal costs. New measurements of quality are being considered now by those producing and those consuming the fuel by assessing numerous variables in the total fuel cycle to achieve the lowest possible power costs.

Jan 1, 1983