Search Documents

By S. C. Nordeng

The program described in this paper is primarily a test of the possible utility of multiple regression in ore search, It was carried out as a cooperative project between White Pine Copper Company, the Institute of Mineral Research and the Department of Geological Engineering of the Michigan College of Mining and Technology. The authors wish to thank Dr. Cleaves Byers, Associate Professor of Mathematics, MCM&T, and Mr. Robert DeBaubien, Graduate Student in Mathematics, MCM&T, for their work in programming the project for the computer,

Jan 1, 1964

By John P. Weir

The planning of an underground mine for successful extraction of a bedded deposit in sedimentary rocks requires the integrated evaluation of many interdependent problems. The development and coordination of feasible solutions are the responsibility of the mining engineer. One of these problems will be discussed herein; this is the design and .layout of mine workings to secure effective control of the strata above and below the deposit. The objective is the simplest possible repetitive system permitting safe maximum recovery at optimum cost. Mining conditions to be encountered must be predictable. The best mining equipment is ineffective unless strata are controlled. Conversely, a mining layout is only of academic interest, if equipment can not be adapted to work it with adequate provision for ventilation, compliance with mining laws, proper ingress and egress and other practical requirements. Strata control, then, is but one of the mining engineer's problems, and the solutions must be worked out concurrently with solutions to other problems. Dr. Karl F. Fetters in his introductory remarks before the Fourth International Conference on Strata Control and Rock Mechanics at Columbia University said that mining engineering ?has come from the stage of empiricism backed by intuitive reasoning, to where it is based on fundamental scientific and engineering principles?. The standard curriculum in mining engineering now reflects such a change. In common with other branches of engineering education, less and less emphasis is placed on practical skills and more and more on broad scientific education. Science, research and the quest for basic truth are stressed, while descriptive courses and the teaching of specific skills are limited.

Jan 1, 1966

By Paul Wellman

The energy problem of the U. S; was emphasized by the oil embargo of late 1973 and early 1974 and it seemed for a time that the Federal Government, under pressure from the general public, might take some corrective action. However, this was not the case. With the gasoline lines gone and an apparent plentiful supply of petroleum products, public concern quickly dissipated., This country is more vulnerable to an oil embargo today than we were in 1973-1974 and this fact should be of concern to all our people. Since 1968, we have used oil and natural gas at a much more rapid rate than we have been able to find new domestic sources; thus, there is an increasing gap between domestic production and consumption and we have filled the gap with ever increasing oil' imports. These imports have increased at an alarming rate in the recent past, some 58 percent in 1976 compared with 1975. Imports are nearing 8 million barrels per day. Then, by applying some simple arithmetic, at $12 per barrel, the resulting trade deficit is $96 million per day or $35 billion per year. Obviously, this cannot be tolerated by our economy over a long period of time. Historically, we have shifted from one fuel to another as is shown in this slide. In 1850 about 90 percent of our fuel requirements came from direct combustion of wood, by 1900 we shifted to coal for 70 percent of our fuel, and now about 78 percent of fuel requirements comes from oil and natural gas. The difference is that the previous shifts were voluntary and the one facing us now is of necessity.

Jan 1, 1977

By Syd Peng, W. B. Guo, F. Du, L. Yang, J. Yw. Cheng

The annual ICGCM China was initiated in 2014. Up to 2023, ICGCM China has been held 9 times. In the 9 conferences during the past 10 years, about 559 papers in 17 topical areas were presented and attendance ranged from 200+ to 400+ each conference. The 42nd ICGCM China was held in Xiangtan, Hunan, China, 10/20–10/22/2023. There were 86 papers presented in 26 topical areas. In addition, an MS and PhD Research Forum was held concurrently with 36 papers presented by MS and PhD candidates in mining engineering from 8 schools. The conference plays an important role in cultivating advanced degree student talents. In this paper, all 559 papers reviewed previously were summarized. In addition, the 42nd ICGCM China is used to illustrate the current and future development trends of coal mine ground control in China. It summarizes the 122 papers (including 36 MS and PhD forum papers) grouping into, and in terms of, 26 topical areas. In addition, its unique and innovative subject areas, short summary of developments as well as conference strengths and shortcomings will also be presented.

Jun 25, 2024

By W. G. Pariseau

Face and pillar bursts, bumps and bounces are violent failures that occur in underground coal mines in response to a complicated interplay of face and pillar geometry, seam depth, coal strength and moduli and interactions between roof, seam and floor strata. Additional complications arise from the presence of gas, mainly methane, and associated pressure and flow that vary with time and are further influenced by the rate of face advance. Numerical models provide a means of quantitatively accounting for the various complications of mining geometry, the stratigraphic column, mechanical properties, gas flow properties and associated interactions. A fully coupled hydromechanical finiteelement code, utAH4, serves the purpose well and allows study of the important interaction between stress concentration and gas pressure in determining safety and stability of the face during the advance of a longwall panel in a deep underground coal mine in central Utah. Face advance is relatively fast compared with gas flow and depressurization in coal seams of low gas permeability. Consequently, gas pressure is high at the face. When a longwall is stationary, depressurization occurs at the face, so effective stress and strength increase. thus, when gas flow at the face is high and requires a pause in face advance to bring gas concentration to an acceptable level, a second benefit occurs because of timely depressurization. However, quantitative analysis of a deep coal mine shows that regardless of gas pressure, high stress concentration is more likely to pose a threat to face and pillar wall stability.

Aug 1, 2013

By Rajat Gangrade, Haotian Zheng, Jarrett Smith, Daniele Nebbia, Mike Mooney

The application of artificial intelligence (AI) to improve tunnel boring machine (TBM) operations requires a significant amount of information to train robust performance prediction models, e.g., for tunneling-induced settlement, productivity, tool wear, etc. This paper presents the AI framework applied to the North-East Boundary Tunnel (NEBT), the largest component of the Clean Rivers Project in Washington, DC. The paper focuses on required elements for real-time AI use to estimate tunneling-induced ground and building deformation and cutter tool wear. Keys to the framework include defining the necessary quantities of data required as well as the process of windowed training, validation and model testing. To date, the models developed for ground deformation and tool wear show satisfactory performance when compared to observed field observations during tunneling.

Jun 13, 2021

By S. V. Tracy

The Outokumpu Skim-Air Flash Flotation machine was developed to separate valuable mineral from gangue as early as practical by floating it with specially designed flotation equipment installed in the grinding circuit. Machines already in service have shown the ability to produce final grade concentrate with an increase in overall recovery and flotation rate while decreasing filter cake moisture and reducing fluctuating feed grades to conventional flotation circuits. The first US production test was carried out in a southwestern copper concentrator with successful results. This report describes the results of the test along with an explanation of the process and the benefits obtainable.

Jan 1, 1986

By Arshad Ali, Mudassar Khan, Waqas Ahmad, Nisar Muhammad, Muhammad Salman

Talc is an important industrial commodity due to its wide-ranging intrinsic properties; however, the presence of iron oxide hinders its industrial utilization. Herein, we report the purification of Pakistani talc through acid leaching assisted by chlorination techniques. Among various acids (i.e., HF, HCl, H2SO4, HNO3, H3PO4, Aqua Regia, H3BO3, and CH3COOH), HF was the most effectual, removing up to 67% of iron oxide at optimized conditions of temperature, 90–95 °C; time, 120 min; HF concentration of 5%; and at a pH of 1. In the second step, chlorination of the talc sample was performed separately by both wet chlorination and dry chlorination. Wet chlorination was carried out using KMnO4 and HCl in slurry phase which shown about 52% removal of iron oxide, whereas dry chlorination with CaCl2 at high temperature attained about 48% removal of iron oxide from talc sample. Further, the wet chlorination of HF leached samples was also performed under optimized conditions which showed up to 87% iron oxide removal. The original and treated talc samples were characterized by EDX and XRD analysis to monitor the changes in the elemental and mineralogical composition of the talc. It can be concluded that HF leaching followed by wet chlorination is an effective method for the upgradation of low-grade Pakistani talc ores.

Aug 9, 2021

By R. V. Stewart

This chrysotile asbestos orebody is located near the northern tip of the Province of Quebec, Canada. It is some 1818 km (1130 mi) north of Montreal; 480 km (300 mi) north of the tree line and is situated within the zone of continuous permafrost. The open pit ore zone is approximately 0.4 km (1/4 mi) in length some 61 m (200 ft) in width and plunges at 25-30 below surface to a vertical depth of at least 610 m (2000 ft). The orebody was originally evaluated by programs of surface mapping, diamond drilling and bulk sampling. The fibre is semi-crude, possesses excellent strength, and good fibre length distribution.

Jan 1, 1978

By A. H. Kaksonen

Numerous reactor designs for biological sulfate reduction have been reported. Fluidized-bed bioreactors (FBR) can efficiently retain biomass and allow high mass transfer and reaction rates. This work reviews the development of various sulfate-reducing FBR processes for treating acidic metal- and sulfate-containing waters and recovering metals from bioleaching liquors. The FBR process performance was evaluated with continuous flow experiments under various operational conditions: fluidization rates, influent pH values, metal, sulfate and salt concentrations, hydraulic retention times, electron and carbon sources, and temperatures. Substrate utilization and sulfide inhibition kinetics were determined with batch FBR-kinetic experiments. An artificial neural network (ANN) model was used to predict the performance of the FBR. Sulfate-reducing bacteria (SRB) were characterized in FBRs with molecular and culture-based approaches with the aim to gain a better understating of the bioprocesses. Based on the studies, FBRs are well suited for the combined removal of metals, acidity and sulfate from water.

Jan 1, 2010

Controlled blasting experiments in small development drifts were conducted at CANMET's Experimental Mine, from August 1992 to November 1993. The objective of these experiments was to develop suitable controlled blasting techniques for small development headings drilled by jackleg with 32 mm diameter holes. The experimentation also aimed to provide insight into blast damage mechanisms. Particular attention was given to the physical-mechanical properties of the rock and the rockmass structural data in order to make the results applicable to other geological environments. The drift faces were approximately 2.4 m by 2.4 m with 36 to 43 holes drilled to a depth of 2.4 m. Cartridged water gels, emulsions and semigelatin dynamite were used in the cuts and as primers, ANFO as the main explosive and decoupled 19 mm diameter semigelatin dynamite charges were used in the perimeter holes. Smooth blasting techniques and pre-splitting were tested in the underground mine. All the blasts were monitored with a multi-channel blast vibration monitor to which was attached sets of high frequency geophones and accelerometers. This first set of experiments has illustrated the efficiency of con-trolled blasting techniques to reduce blast damage and demonstrated the need for further research to improve the safe and efficient use of explosives.

Jan 1, 1995

By Patrizia Pereyra, M. Guzman, C. Toledo, J. A. Rau, A. Ruiz

The use of mining tailings-based geopolymer binder as a substitute for cement can be an interesting alternative to the problem of final disposing of large volumes of them. Indeed, mining tailings have a high silica content, which makes them suitable for geopolymerization. The tailings samples contain Cu, Pb, Zn, As, Sb, Cd and Bi, mainly. X-ray diffraction results show that the tailings are composed of quartz, SiO2 (81%). Geopolymerized tailing samples (GTPS) were obtained by varying the ratio of SiO2/ Al2O3 and SiO2/NaOH. The compressive strength of the GTPS varied between 2 MPa and 8 MPa. The electrical conductivity in the leaching tests varies between 13.91– 16.11 mS/cm2 indicating that ions are present in the solution. However, the pH = 10.5 indicates that acidity is not being generated. The element that mostly leaches is iron. The highest percentage of leaching is observed for cadmium (69%) and chromium (93%). The concentrations of elements are under the maximum permissible limits for water according to the Peruvian legislation. However, mass transfer leach tests and immersion leach tests must be realized.

Feb 1, 2024

By S. A. Elmquist

Research activities performed by Cleveland-Cliffs Research and Hibbing Taconite plant personnel during the last decade have resulted in the development of an improved autogenous mill grinding circuit. Minus one (1) inch autogenous mill trommel oversize material, con-sidered to be a critical size, is magnetically cobbed and then crushed to 100% minus 3/8" prior to reentry into the feed end of the mill. Autogenous mill capacity increases, up to 25%, have been measured in pilot plant tests using this approach and are also anticipated for the Hibbing Taconite concentrator which presently has reached a 15.5% improvement.

Jan 1, 1994

By Richard P. Killmeyer, Carl P. Maronde, W. W. Wen, Peter J. Suardini

Under a cost-shared Department of Energy contract, awarded as part of the Coal Preparation Program&apos;s High Efficiency Preparation subprogram, Custom Coals International will be installing and testing a 227 kglhr micronized-magnetite cycloning circuit in PETC&apos;s Coal Preparation Process Research Facility. The project includes the design, construction, testing, and decommissioning of a fully integrated circuit complete with feed coal classification to remove the minus-30-micron material, dense-medium cycloning of the 300 by 30 micron feed coal using micronized magnetite (<10 microns), and medium recovery via drain & rinse screening and various stages and types of magnetic separation. This paper will describe the micronized-magnetite beneficiation technology and the scope of work for this project including an update on the status of the project, the circuit, and the proposed test plan.

Jan 1, 1995

By N. H. Coates

The Bureau of Mines designed, constructed, and operated an 18-inch- diameter, fluidized-bed combustor for highly caking coals to evaluate the method for possible application to power generation. In initial tests, combustion was carried on successfully, with carbon losses as low as 0.8 percent. Coal ash was not satisfactory as a bed material, but mullite proved to be acceptable. Overall heat-transfer coefficients from the bed (-20 + 50 mesh mullite) to a water-cooled tube were about 75 Btu/hr-ft2- °F.

Jan 1, 1970

John C. Greenway was responsible for much of my success in the seven years from what I called the end of my apprenticeship in exploration until I entered the Army in World War I. I first met Green- way on my return from Promontorio and, as he was replacing Powell, he was to be my boss. Even at first glance you couldn&apos;t help liking and trusting him. He was tall, well built, and erect-an old Yale athlete. After college he became a captain in the Rough Riders and a friend of Theodore Roosevelt, distinguishing himself in the Cuban campaign. He made good friends in all ranks of the Rough Riders, some later becoming leaders of industry and others following Greenway where-ever he went. After the Spanish War Greenway worked for iron mining companies around the Great Lakes and when the directors decided that Calumet and Arizona needed a new manager the ones who were also prominent in Oliver Iron Mining Co. selected Greenway It was a lucky choice for Greenway and for me. He became the best manager among those who ran the big copper mines He was open-minded in encouraging discussion and even opposition-until he made up his mind. Then, in military fashion, everyone must follow his decision without question. I think this is an essential of good management. Unfortunately a few did not feel this way and they had to leave. It was characteristic of those times that respect for the boss was so great that in the 16 years in which he was one of my best friends I, like all under him, always called him "Mr. Greenway." Soon after he arrived Greenway asked the leading mine operators in the southwest, Dr. Louis D. Ricketts and James S. Douglas, son of the Dr. James Douglas who had made Phelps Dodge great, to do special work for Calumet and Arizona. I found later that the object of the study was to determine the terms on which the half-dozen Warren District properties of Calumet and Arizona were to be joined in one

Jan 1, 1976

By Zoë Dugdale, Gerald Poplin, Tim Bauerle

"Fatigue presents several challenges for the mining industry. Depending on the specific occupation, daily work or operational setup on any given mine site, mining jobs can have a fair amount of labor-intensive tasks mixed with monotonous and repetitive duties. Combined with the long working hours and shift-work schedules of mining work, the prevalence of fatigue in mine workers may seem rather unsurprising.Mining is certainly not alone in facing the challenge of addressing worker fatigue. Indeed, many of the characteristics above mirror the similarities of fatigue in other industries, such as health care, aviation and security. To the extent that fatigue in mining acts like fatigue in any other industry, then any fatigue management applications, trainings, or interventions in existence can be borrowed from other industries and applied to mining in a cookie-cutter approach. However, some have argued that mining in particular is especially susceptible to increases in the prevalence of fatigue beyond the characteristics listed above due to the multifaceted combination of factors in mining environments associated with fatigue: dim lighting; limited visual acuity; hot temperatures; loud noise; highly repetitive, sustained, and monotonous tasks; shiftwork; long work hours; long commute times due to mine site remoteness; early morning awakenings; and generally poor sleep habits (Canadian Centre for Occupational Health and Safety, 2012; Legault, 2011). Legault (2011) in particular argues that it is the combination of these factors simultaneously that can make mineworkers particularly susceptible to sleep deprivation and fatigue in comparison to other industries where these factors are often not present all together. If fatigue looks and acts different in mining, as others have argued, more research is needed to determine if, how, and why worker fatigue might need to be managed differently in mining.While the burden of fatigue on the mining population has not yet been evaluated thoroughly, methods and measures of fatigue management remain a popular point of discussion. Many commercial suppliers and consultancy groups have begun to develop technologically based fatigue monitoring systems (McMillian, 2013). Some technologies can monitor vehicle operators for indicators of wakefulness, such as percent eyelid"

Jan 3, 2018

By James P. Rider

Significant advances in longwall mining technology and equipment have occurred over the last decade by the late 1990s, longwall mine output accounted for 40% of all underground output in the U.S. and today longwall mines account for approximately 50% of coal produced underground in the United states. A 51% increase in average shift production rates has occurred over the last 15 years. this increased longwall productivity has meant that far more dust is being produced and controlling respirable coal dust presents an ongoing challenge for coal mine operators the National Institute for Occupational safety and Health (NIOSH) conducted a series of benchmark surveys at longwall operations across the country to identify current operating practices and the types of controls being used. Gravimetric and instantaneous dust sampling was completed to quantify the dust levels generated by major sources on the longwall section and to identify different control technologies in use today substantial reductions in dust levels were realized at sampling locations on the face when compared with ongwall surveys conducted in the 1990s results from the underground dust surveys and current longwall dust control technology and operating practices will be discussed. Mining Engineering, 2011, Vol. 63, No. 9, pp. 74-80. Official publication of the society for mining, metallurgy and exploration, Inc.

Jan 1, 2011

By K. C. Kocsis

Underground ventilation systems, which require electricity to operate the fans and fossil fuel for heating in winter, can account for a significant portion of the energy consumption of mines. Recent studies have shown that the ventilation system in deep and highly mechanized metal mines could be responsible for 40 to 60 percent of their overall energy consumption. Presently, underground ventilation systems are designed for peak air volume requirements, which usually occur well into a future stage of the mines’ operating life. As a result, during their early operating stages, the intake air volume of the mines could be well in excess of their true air volume needs. Such ventilation systems could be considered as uneconomic, and to remain competitive the ventilation design needs to improve while the mines are trying to reduce energy consumption and their carbon footprints. This paper introduces a new mine ventilation design method where an underground base-metal mine’s ventilation system is designed by integrating discrete-event mining process simulation (DES) with mine ventilation modeling techniques. Furthermore, based upon the output data generated by means of discrete-event mining process simulations, the air volume requirement for the operating life of the mine is determined for “traditional” versus “activity-based” ventilation requirements. The output data generated through ventilation simulations are then used to quantify the economic and environmental benefits of an activity-based ventilation delivery system.

Jan 1, 2018

By S. C. Howell

The mining of taconite, to provide feed for a processing plant, requires that the flow of material continue uninterrupted. This means first, that the crude must be of a size acceptable to the primary crusher in order to reduce the delays caused by plugging the crusher with chunks. Secondly, elimination of oversize in the pit will reduce costs of all wear parts used in the mining and processing of taconite. Savings in wear parts is readily recognized in dipper teeth, bases, buckets, truck boxes, and crusher parts, both primary and secondary. During the early days of taconite mining, it was soon recognized at reserve mining company&apos;s Babbitt operations that experience in mining other ores was not always (or ?necessarily??) Applicable to excavating taconite. This was especially true in drilling and blasting. Blasting of small tonnages in single or double rows simply filled the pit with scattered chunks and provided very shallow banks for shovel loading. It also created problems for the jet piercers, since all drilling had to be performed in fractured areas. Drilling efficiency suffered and costs were extremely high. Shovel and truck efficiencies were also low and again costs were high. A high percentage of secondary breakage was required. This necessitated the use of numerous man hours to jackhammer holes in chunks, preparatory to loading and blasting. After the chunks were reduced, bull- dozer and grader hours were needed to pile the taconite for acceptable shovel loading.

Jan 1, 1968