Search Documents

By G. V. Borquez

For many years drilling and blasting has been considered more of an art than a science. This is still true in some respects, but today scientific approaches to drilling and blasting design must be used to plan an efficient operation which achieves desired fragmentation within constraints. These constraints involve minimizing damage to the wall or nearby permanent structures and avoiding undesirable fragmentation and mine dilution which can adversely affect operation costs. The degree of fragmentation by blasting is the most important single factor in any attempt to optimize the overall cost of the mining operations. The mining cycle begins with the drilling and blasting operations, which result in a given blasted rock size distribution. While this operation represents only about 20% of total mining costs, the efficiency and costs of the subsequent operations are strongly dependent on the fragment distribution obtained.

Jan 1, 1986

By R. W. Henn

Introduction Shotcrete, by the American Concrete Institute definition, is mortar or concrete pneumatically projected at high velocity onto a surface. The term gunite is still common in literature. It is a trade name established by Cement Gun Co. of Allentown, PA, around 1911 for a dry mix of fine aggregate material, hydrated at the nozzle, and pneumatically projected at high velocity onto a surface. This article will discuss shotcrete applications, ingredients, mix proportioning, batching and mixing, admixtures, testing, and steel fiber vs. conventional shotcrete. Applications Shotcrete is used primarily by the mining and underground construction industries to temporarily stabilize an excavated rock surface until a permanent cover can be installed. It may also be used as the permanent covering material. Other uses include refractory material, architectural finishes, slope stability, wearing surfaces, repairing existing concrete structures, fireproofing, and corrosion protection of steel. Wet Versus Dry Process In the wet process, all ingredients, including water but not accelerator, are mixed the same way as normal concrete before its placement by pneumatic projection. The accelerator is added in a liquid state through the nozzle at the point of placement. In the dry process, all ingredients, including acceleration in dry form but not water, are mixed just before placement by pneumatic projection. Water is added through the nozzle at the point of placement. Liquid accelerator may be added at the nozzle in the dry process. Ingredients Shotcrete consists basically of the same ingredients as concrete with some limitations. Type I, II, and III cements are used. However, Type II seems to be used most in underground applications. This can be attributed to ground water at most sites having slight to moderate concentrations of sulfates. Air-entraining cement or air-entraining admixtures are generally not used in dry mix shotcrete. It is generally agreed that it is impossible to entrain air due to the absence of the usual concrete mixing action, and the high velocity of impingement of the material on the application surface. Air-entraining cement or air-entraining admixtures are used in wet mix shotcrete. Their use, however, is not widespread due to the placement method and the fact that high velocity air drives off most of the entrained air. Test results are not conclusive in showing any durability increase of shotcrete to freezing and thawing by using entrained air. In spite of current practice, the trend is toward additional research, with more agencies and owners requiring the use of entrained air. The philosophy behind this is that some entrained air is better than no entrained air to increase durability to freezing and thawing. The aggregates used in shotcrete are the same as those used in concrete. However, the largest coarse aggregate presently used is 19 mm (0.75 in.). A typical gradation requirement is shown in Table 1. The water quality requirement for shotcrete is the same as that for concrete. Accelerators are by far the most important admixture in shotcrete.

Jan 6, 1984

By J. H. Kelley

In this paper, we show that the methane emission and the dust generation in under-ground mining currently and in the future pose operational, health and safety conditions which adversely Impact face productivity and worker satisfaction. One solution is the use of a dual-aircourse system of ventilation. In this concept, one aircourse captures and exhausts to the surface the dust generated and the methane emitted in coal/mineral fragmentation while a second aircourse provides workers with cleaner air for breathing and comfort. Various dual-aircourse configurations adapted to the Variable Wall Miner are analyzed and compared with conventional mining in gassy seams, indicating a marked reduction in the required air quantity and the number of aircourses.

Jan 1, 1996

By Kerry Lahti, Bryan Ulrich

On Feb. 11, 2005, more than 20 mining professionals gathered in Elko, NV for a day-long round-table discussion on heap leaching. Attendees included project managers, operators and environmental professionals. They represented 10 mining organizations. Knight Piésold sponsored the special event. Its seven representatives included three staff members from the company’s Elko Operation, and one each from its Denver, Cajamarca (Peru) and Vancouver offices. The roundtable format was chosen to allow people from the mining industry to share ideas and experiences in an open forum. Rather than presenting prepared talks, spontaneity was encouraged. This resulted in a lively and enjoyable discussion.

Jan 1, 2005

By J. Patrick Powers, Arthur B. Corwin

Modern improvements in hydrogeology make it possible to predict with good reliability the performance and cost of ground water pumping systems in many tunneling situations. The testing and analysis techniques are presented. Data from the Buffalo NY LRRTS (1978-1980) illustrate the successful application of the technique for tunneling in rock. Data from the Red Hook Interceptor Tunnel in Brooklyn NY (1978) illustrate the application in soft ground. The Red Hook project also illustrates concerns for the side effects from dewatering, such as ground settlement and damage to timber structures. At Red Hook protective measures included compressed air, artificial recharge and controlled dewatering. Given the uncertainties of the underground, the possibility of unexpected situations must be considered. A hard rock sewer tunnel in Atlanta, Georgia (1982) illustrates an unexpected problem, and the emergency measures used to solve it.

Jan 1, 1985

By Bruce Watzman

"Few issues are more important to the National Mining Association (NMA), the U.S. mining industry and NMA’s MINExpo International 2016 exhibitors than safety.Global mining safety and health is a journey necessitating continuous improvement, collaboration and innovation on the part of both mining operators and their suppliers.MINExpo 2016, which takes place Sept. 26- 28, 2016, in Las Vegas, provides attendees with the opportunity to view technologies to help refine management of mining safety and health, utilizing NMA’s CORESafety system. CORESafety ‘One of the best’Launched by NMA in 2011 and moving forward ever since, CORESafety is driving continuous improvement in safety and health performance among participating industry companies by shifting from a command-andcontrol regulatory approach to a risk-based systems approach built on the Plan-Do-Check-Act model (Fig. 1).Considered an exemplary safety and health management system, NMA’s CORESafety system helps mining operators change their approach to safety and health management by enhancing the safety and health culture throughout their organizations. Although it is challenging to consistently and completely control all the factors and variables occurring in daily mining operations, experience has shown that applying systematic controls to as many variables as possible is the most successful approach for improvement in mining safety and health.When embarking upon the development of the CORESafety framework, NMA’s leadership set an ambitious goal to eliminate fatalities and reduce the injury rate 50 percent in five years, or the “0-50-5” goal. While the goal has not been met yet, the steady progress has been extraordinary with fatalities among participating companies dropping 45 percent during the period 2011-2015 (Fig. 2). Data also demonstrate that, as participating companies increase their level of implementation, total injury rates have also declined (Fig. 3).In a September 2015 interview with NMA, Penn State University mining engineering Professor Jeffrey Kohler praised CORESafety as “an inspired and timely program that brings together key elements to achieve safety and health goals.”"

Sep 1, 2016

"The National Mining Hall of Fame and Museum (NMHFM) announced the 2018 National Mining Hall of Fame inductees. This year’s inductees, selected by the National Mining Hall of Fame’s Board of Governors, represent exploration, extraction, management, education and research and development in the U.S. mining industry. Their contributions have had significant and lasting impacts on the mineral and mining industry; these individuals were selected for being mavericks, thought leaders, researchers, educators, mentors, wealth builders and philanthropists.Professor John M. Guilbert, Dr. Leo J. Miller, Robert E. (Bob) Murray and Douglas (Doug) B. Silver will join 240 other mining industry luminaries when formally inducted into the National Mining Hall of Fame on Sept. 29, 2018. Additionally, the Prazen Living Legend of Mining Award will be presented to the Freeport- McMoRan Foundation. The 31st Annual Induction Banquet and Ceremony will be held at the Ritz-Carlton in Denver, CO.2018 National Mining Hall of Fame inducteesProfessor John M. Guilbert was a renowned geologist and professor of economic geology at the University of Arizona; he had a distinguished 50-plus year career in academia and business. Guilbert, together with J. David Lowell, worked on the most important breakthrough in mineral exploration in the last 100 years, the Porphyry Copper Model. This work, known as the Lowell and Guilbert Model, was utilized by exploration geologists worldwide over the next four decades to discover hundreds of millions of tons of copper metal and numerous profitable mines including the prosperous Bajo de la Alumbrera copper mine in Argentina. Guilbert was a founder of The World Museum of Mining in Butte, MT. He was the recipient of countless awards including the Society of Economic Geologists (SEG) R.A.F. Penrose Medal as well as the D.C. Jackling Award from the SME.Dr. Leo J. Miller was a maverick in the mining industry and no armchair geologist. He believed that active fieldwork, on foot with a rock pick, was indispensable for exploration. His basic tenet was to absorb as much information about an exploration target up front, formulate ideas – sometimes novel ones — and then get out into the field to prove those ideas. Miller was known to diverge from the standard interpretation of the geological processes, which formed the mineral deposits, and to apply innovative applications of high-tech tools to more usual exploration programs. This approach resulted in a 50-plus year career that included the discovery of the Kidd Creek massive sulfide deposit and the development of the Lee Creek phosphate deposit; which other explorers had previously given up on, believing whatever phosphate might be present would be too difficult and expensive to mine. The recipient of many honors and awards, Miller received the SME Robert M. Dreyer award in recognition of outstanding achievement in ore discoveries."

Jan 8, 2018

By Alain Broussaud, Guy Fourniguet, Jacques Franck, Pierre Conil

Steady-state simulation is now in current use to assist mineral processing plant design and optimization. However, the reliability of results generated by simulators has not until now been seriously investigated. A simulator supervision algorithm was designed and programmed to study both the influence of the reliability of experimental data on the accuracy of unit operation model calibration, and the influence of unit operation model accuracy on the results of direct plant simulations. An application to a grinding flotation plant is described and discussed. The approach may open the way to the quantitative analysis of the risks taken in mineral processing projects, which would be similar to the application of geostatistics to mining projects.

Jan 1, 1990

By James G. Tilton

Subsidence resulting from mining operations, has been the object of sporadic study for many years. Reports have shown that subsidence has ranged from minor settlement detected only by precise measurements to great slips where buildings are destroyed, roads disrupted, and large fissures opened at the surface. For years, a controversy has raged over the question of whether there is a positive or negative angle-of-draw. None of these questions can be given a flat answer for the variables controlling, subsidence are infinite. Generalizations can be made for various situations and areas but some means of control must be executed.

Jan 1, 1966

By Jim Dunn

For decades many of us who are associated with the mineral industry have tried to show the public its economic and strategic importance. Some of the mineral industry's proponents have been politically powerful figures and have been widely quoted. Yet, as measured by public opinion, legislative support, or almost any other standard, our efforts have been inadequate. It is apparent that a set of environmental beliefs that discredit industry, firmly held by a number of idealistic persons, has had wider coverage in the media and in schools than has the mineral industry's message. Although the fervor of our idealistic friends is often unfounded and, their stands unscientific, they must be considered seriously. Unless we address the issues in terms the idealists will understand, the mineral industry will have little influence on them or on the general public. A. striking thing is that, quite often, translation of idealists' views into action has been counterproductive. The reason is obvious. Excessive amounts of money and energy have been spent on relatively minor problems. The common result is that larger problems have been created. It may be possible to help anti-industry idealists understand their own dependence on minerals, and thus render their views more realistic, if they are shown more effective ways to reach their stated goals. If those goals can be shown to be held in common by all sensitive human beings -- including those in business and industry - the dialogue becomes one of how to achieve common ends. Individual mining companies acting by themselves have little possibility of success, and companies working in unison through trade associations have not been successful. Further, it is unlikely that industry in general can be successful in changing minds unless it seeks outside help. But friends among those who influence public opinion have been hard to find. Historically, help from media has proven difficult to get. Nor has enough help from educators been forthcoming. Yet, a war is going on in the technological, philosophical, and political trenches, even though much of the public is not aware of it. For the first time in years, there is row a significant and growing number of eloquent and brilliant thinkers on the side of free enterprise and industry, many of them environmentalists, but without the anti-industry mind-set. They have had remarkably little help from the private sector or even from the present administration. Industry may do far more for itself in the long run by encouraging these brave but bruised individuals and their organizations than by trying to work alone. These friends of free enterprise are working against a seemingly stacked deck relative to much of the media, the bureaucracy, and the educational system. However, despite their problems, their success to date has been remarkable. With more cooperation from industry they should do even better.

Jan 1, 1987

By S. J. Schatzel, K. M. Ajayi, E. N. Rubinstein, Z. Khademian

This study simulates the impact of a shale gas well casing breach near a longwall mine. Field studies are conducted to measure mining-induced permeability changes over the abutment pillar of a longwall mine, and a geomechanical model is developed in 3DEC, a three-dimensional numerical modeling code, to predict the aperture of fractures in the overburden at the study site. The predicted aperture values are used to determine mining-induced permeabilities and the results are compared with the field measurements. These aperture values are provided as inputs into fracture flow code (FFC), which generates a stochastic discrete fracture network (DFN) model for the study site and predicts the potential shale gas flow to the mine. Results from 100 DFN realizations are statistically analyzed using the bootstrapping method to compensate for notable variation in fracture geometry. The results show a significant difference between the gas inflow for nearby panels due to increase in the induced permeability during mining of the second panel. The average gas flow to the mine was calculated as 4.72×10−2 m3/ s (49 cfm) for a hypothetical breach at the Sewickley horizon during the first panel mining, 8.97×10−3 m3/ s (19 cfm) for a hypothetical breach at the Uniontown horizon during the first panel mining, 2.16×10−1 m3/ s (458 cfm) for a hypothetical breach at the Sewickley horizon during the second panel mining, and 8.07×10−2 m3/ s (171 cfm) for a hypothetical breach at the Uniontown horizon during the second panel mining. Depending on the mine ventilation system, this could result in methane concentrations exceeding regulatory limits. Hence, these findings provide insights into the potential risk of an unconventional gas well casing breach near a longwall mine under shallow cover.

Feb 15, 2023

By Rajendra K. Devala, Sukumar Bandopadhyay

In order to be able to design an adequate mine ventilation system it is necessary to understand how pollutant masses disperse into turbulent ventilation air streams. The mixing of gases and dusts with ventilating air, and dispersion of these pollutants in mine airways, are important flow or transfer problems. For the solution of such problems, the finite difference technique is often used. In this paper, numerical approximation schemes for the solution of the mass transfer problem have been developed using several explicit finite difference schemes. Results from these schemes have been compared with the analytical solution for spatial and time increments using the concept of Root Mean Square error. The comparison of various schemes reveals that the explicit finite difference schemes analyzed here give more accurate results at lower velocities, though the results are dependent on the spatial and time steps considered. At higher velocities the schemes tends to oscillate about the analytical solution. INTRODUCTION In mining, most of the mine air pollutants, such as respirable dust, methane, blasting fumes and diesel exhaust, are produced at the mine face and in haulageways. Injection of any of these pollutants in the mine ventilating air causes disturbances of the equilibrium state of the pollutant concentration of the ventilating air. The mixing of these gases and dusts with the ventilating air are typical examples of mass transfer processes. Pollutants are diluted by the stream of ventilating air flow along airways and discharged into the outside atmosphere of the mine through a return shaft. The dispersions of these pollutants in mine airways are important flow or transfer problems. Knowledge about pollutant sources, emission and transport of these pollutants are essential for ventilation planning and design to ensure good engineering control over air quality, quantity, and environmental conditions. Modeling of mass transfer phenomena in mine ventilation is largely based on extensive studies of turbulent dispersion in wind tunnels and the lower atmosphere of the earth. The general approach in the formulation of models lies in the recognition that these mass transfer phenomena can be conceptualized as a flow problem that can be solved by the general application of Taylor's theory (1954) of turbulent flow and diffusion with modification appropriate static and dynamic parameters. If the face zone is initially contaminated by a pollutant over a long section (e.g. instantaneous exposure of large gas accumulation, rapid methane release etc.), the process of decontaminating the mine workings can be regarded as displacement and diffusion of the tailing edge of the cloud of contaminates in the form of a semi-infinite gas body, for which a one-dimensional mass transfer equation is represented by: [at + u • ax = Ex ex2 + f (x,t)(1.1)] In Eq. (1.1), the term [~~] is the rate of growth of the concentration in the differential element, while a [(5xx )] is the net gain of material due to convective transfer. The two terms balance the total loss of material due to turbulent dispersion that is represented by [Ex . 21] and f(x,t), the source term for the pollutant in the roadway. Several cases of mass transfer that occur in mining can be identified and modelled using the conservative volume element method. The governing equation, along with the associated boundary and initial conditions, source terms and their solutions are detailed elsewhere (Bandopadhyay and Ramani, 1988, Devala, 1989). Only one mass transfer situation is presented (Figure 1) here for the present analysis. Mixed Evolution of Pollutant (multiple pulses) Typical examples of these situations are emission of pollutants from multiple diesel vehicles in the face area, and gas emission from standing pillars as well as from broken coal seam during coal cutting with a continuous miner. The mathematical statement of the problem along with the initial and boundary conditions are given below, Governing Equation: [do+u- =E d2c(1.2) ataxx dx2] Initial conditions:

Jan 1, 1993

By J. H. Tu

The technical paper correctly points out that the kriging variance is not a good measure of the uncertainty of the estimated (i.e., kriged) value of individual blocks. The authors claim that their proposed jack-knife method, which is a rekriging of each block by eliminating, in turn, one sample from m the original sample set and then taking the average of the rekriged estimates, not only gives good block estimates, but the resulting jackknife kriging standard deviation is a useful indicator of the "true uncertainty associated with block estimates." However, they immediately abandon the idea of using the block-by-block standard deviations, reasoning that these standard deviations are not independent and that there is no easy way to utilize them. There may be another reason for not using them. The jackknife standard deviations for individual blocks given in their example are mostly in the range of 0.004 to 0.005 oz/st (0.14 to 0.17 g/t) with only one block having a high value of 0.012 oz/st (0.41 g/ t). These individual block standard deviations are as low as the jackknife standard deviation for the mean grade of the entire shape, i.e., 0.0041 oz/st (0.14 g/t). Do they represent the "true uncertainty" .of the individual block estimates? Could the authors explain this? In a global shape consisting of a large number of blocks, any given sample will affect the kriged estimate of only those few blocks within its vicinity. This is the rationale for the authors' selective rekriging, making the jackknife algorithm more efficient. On second thought, why not do away with jackknifing altogether? Just cumulate and normalize, if necessary, the kriging weights of each sample used during the ordinary block kriging process, and then compute the global variance from these kriging weights and their respective sample grades? After all, isn't the global mean grade nothing but the weighted average of the samples used in the estimation? Reply by G.S. Adisoma and M.G. Hester The jackknife is one of the many tools in a practitioner's toolbox to solve estimation problems. The strengths of the technique lies in its simplicity, i.e., it uses the concept of mean and standard deviation and the fact that it can be easily combined with other tools, in this case kriging. Because the jackknife kriging (JK) estimate is also the mean of the pseudovalues, the JK standard deviation is attractive just as the standard deviation of the mean explains the variability of the data. The difference is that the pseudovalue calculation in jackknife kriging uses the ordinary kriging (OK) weighting scheme instead of simple arithmetic averaging. The data used to illustrate the jackknife technique in the paper con¬sist of high values that are roughly three times the low values. The resulting JK estimate of the block grades show that the highest estimate is roughly twice the grade of the lowest estimate. The contrast between the low and the high estimate is more evident in the JK estimate than in the OK estimate, even though the mean grades of the blocks for the two estimates are very similar. Nonetheless, in this paper, we are concentrating more on the need for a more realistic measure of uncertainty, or precision, for the estimate. Unlike its OK counterpart, the JK standard deviation of the blocks clearly reflects the original data variation. The highest JK standard deviation of the blocks is three times its lowest value. This follows our intuition that, when the samples used to estimate a block is more variable, the resulting estimation variance (or standard deviation) should be higher than the case where the samples are more uniformly valued. However, block-by-block standard deviation or variance is of little practical value in reserve estimation and classification, as well as in mine planning. One is usually more interested in quantifying not the variance of the individual block estimate, but the uncertainties associated with a much larger dimension, such as the minable reserve. Thus, the thrust of the paper is to find a simple way to obtain a single estimation variance or standard deviation associated with the reserve grade estimate. The discussion by J.H. Tu did not mention how one would obtain the global variance from the OK weights and the sample grades. As a technique that offers a data value-based measure of uncertainty for its estimate, the "leave-one-out" jackknife fills this need nicely through the block kriging shortcut approach described in the paper. Note: The first column and the last two columns of Table 3 in the paper should have contained a single number each, namely, an OK estimate of 0.0317, a JK estimate of 0.0333 and a JK standard deviation of 0.0041 oz/st, respectively, for the shape, as are obvious from the text.

Jan 1, 1997

By L. Westerstrom

Supply and Demand After a dismal first half, the industry saw a marked improvement in its markets during the final six months of 1983. Domestic consumption was 17.6% higher in the second half of the year, primarily due to a surge in electric power requirements. The sharp increase in demand for electric power during the third and fourth quarters afforded utilities the opportunity to lower stocks that had accumulated to record levels during 1982. Consumer stocks were reduced from 179 Mt (197 million st) at the end of June to 153 Mt (169 million st) by the end of the year. That is the largest inventory drawdown on record during a six-month period without a major coal strike. Despite the huge depletion in inventories, coal production in the second half of 1983 rose 1.3% above output in the second half of 1982. However, because of the disappointing first half, production in 1983 totaled only 712 Mt (785 million st), 6.4% less than the 760 Mt (838 million st) produced in 1982. Demand The extent to which the economic recovery affected coal markets in 1983 varied: • total domestic coal consumption increased 4.2%; • electric utility coal consumption increased 5.3%; • exports declined by about one-fourth; • coal consumption at coke plants declined 9.5%; and • coal consumption in the other industrial sectors increased 2.9%. Domestic coal consumption totaled 667 Mt (737 million st) it 1983, 27 Mt (30 million st) more than 1982. Electric utility consumption increased from 539 M1 (594 million st) in 1982 to 567 M1 (625 million st) in 1983. Coal consumption at coke plants declined from 37 Mt (41 million st) to 34 M1 (37 million st). Residential and commercial use increased 181 kt (200,000 st) - from 7.4 to 7.6 Mt (8.2 to 8.4 million st). Electric Utilities: Electric power generation increased 3.1% in 1983. Demand for electric power increased in all major consumer categories. Residential and commercial use rose 2.7% and 3.3%, respectively. The most striking increase, however, and indicative of the economy's strong upturn, was the increase in industrial electric power use. Industrial power requirements, which declined 9.8% in 1982, rose 4.1% in 1983. The electric utility sector continued to expand its use of coal last year while lowering its requirements of oil and natural gas. In 1983, electric generation from coal increased 5.7%, while genera-

Jan 5, 1984

By C. H. Grant

On the Mesabi Range, Ammonium Nitrate is used for blasting a variety of materials having widely varying blasting characteristics. The materials vary from hard, dense, magnetic taconite, which requires heavy blasting, through relatively soft, earthy, direct shipping ores, which require only light blasting to facilitate shovel operation. In view of the fact that materials gradational between these two end members are encountered in large tonnages, it is evident that a wide range of blasting situations face the mine operators on the Mesabi Range. In April of 1956, at Cleveland-Cliff s Hawkins Mine near Nashwauk, Minnesota, a fertilizer grade of Ammonium Nitrate prills was first used as a blasting agent. This first attempt was made without the addition of any carbonaceous material and even though it did go off, the force was not sufficient to produce the required results. Fuel oil was then added In the amount of one gallon for each 80 pounds of Ammonium Nitrate, with the oil and Ammonium Nitrate being added to the hole simultaneously. This blast was successful. Since then most of the mining companies have used Ammonium Nitrate, experimenting with various ratios of oil and fertilizer, mixing these ingredients either before or during loading of the holes. Since the additional of fuel oil to the Ammonium Bitrate before loading produces a more uniform saturation, most companies have adopted the method of pouring the fuel oil directly into the Ammonium Nitrate bags and then pouring the mixture into each hole. The ratio of 3- ½ quarts of fuel oil to each 80 pound bag of Ammonium Nitpate prills is now being used.

Jan 1, 1958

By R. F. Balazik

By March 2001, shrinking global markets, reduced consumer spending and declines in domestic manufacturing and industrial output ended the longest economic expansion in US history and pushed the nation’s economy into its first recession in a decade. Aggravated by the terrorist attacks of Sept. 11, the recession led to large reductions in the domestic production of processed mineral materials. Some of the most significant production declines in the US metals industry were registered by aluminum, copper and steel producers. They faced strong foreign competition, higher energy costs and lower prices for their products. However, homebuilding and other domestic construction sectors — major users of nonmetallic mineral products such as cement, brick, glass and stone — remained strong enough to help raise the output of industrial mineral materials slightly above previous year levels. A strong US dollar continued to weaken the competitive stance of US metal and nonmetallic mineral materials companies alike against foreign producers in markets at home and abroad.

Jan 1, 2002

By Stephen G. Hardcastle, Michel G. Grenier, Kevin C. Butler

Today there are numerous electronic rotating vane and thermal (hot-wire) anemometers, as well as vortex meters available to measure air velocity. Of these, a laboratory and field evaluation has found that certain instruments are better suited to routine airflow measurements in mine roadways and ventilation ducts. This paper concludes a study sponsored by the Atomic Energy Control Board of Canada, that was introduced at the 5th U.S. Symposium. The study investigated the suitability of currently available electronic anemometers as replacements for the traditional mechanical analog devices while maintaining standard methods such as the continuous traverse. Six electronic instruments were subjected to extensive tests under controlled conditions both in a wind-tunnel and in the field at an underground mine. The evaluation concluded that ergonomics and design were major considerations in unit preference as most of the instruments had very similar performance characteristics. Specific findings were: a) In the wind-tunnel the vane anemometers, especially the "micro" vanes, were more susceptible to misalignment or yaw effects but these were not noticeable in the field; b) Both the vortex and hot-wire anemometers were suitable for continuous traverses of mine roadways; c) Traversing ventilation ducts was more practical than a Pitot-tube multi-point assessments or discharge measurements; d) Yaw is a major concern in duct measurements; e) The continuous traversing method for roadways overestimates the average air velocity; f) Hot-wire anemometers can require significant air density corrections; and g) Hot-wire anemometers are better suited than rotating vanes to mine roadways of less than 1 m/s average air velocity. Based on research detailed in this paper, the ventilation engineer should be able to match the mine's requirements with the presented instrument performance characteristics, thereby optimizing the purchase of a new anemometer and the efficiency with which air velocities are measured.

Jan 1, 1993

By A. Henchiri, G. A. Gruber

INTRODUCTION Phosphatic resources may be quantified in terms of ore tons and phosphate analyses; however, to quantify phosphate reserves it is necessary to estimate the tons and quality of phosphate rock that can be extracted from the ore. The yield and grade of phosphate rock that can recovered from sedimentary phosphate deposits are usually difficult to estimate because of variations in stratigraphy and/or mineralogy. Prospecting phosphorite ores for purposes of estimating reserves and preparing mine plans requires considerably more effort than defining ore thickness and P205 content. In Florida, for example, it is standard practice to prospect by core drilling and to subject each strata (split) to beneficiation testing, and to perform detailed chemical analyses on the beneficiated products from each strata. For a completed drilling pattern the area of influence of each hole is 2.5 acres. The number of strata per drill hole typically varies from two to five, and thus complete prospecting of a 40acre tract requires drilling 16 core holes and beneficiation testing of about 48 ore samples. Florida practice is not appropriate for all phosphorite deposits. Functional drill rigs and trained drillers may not be readily available. Water for core drilling may be unavailable and the characteristics of either the overburden or ore may require careful attention and excessive cost to obtain representative core samples. Alternate ore sampling methods include auger drilling, rotary drilling to obtain cuttings, and the excavation of trenches, pits, and shafts. Drill cuttings samples are generally the least expensive to obtain, but they are usually unsuitable for beneficiation testing because of particle size reduction during drilling. Ore samples from surface trenches and pits are expensive and may not be representative of deeper ore. Ore samples from shafts are the most expensive to obtain, but if taken properly they are reliable for use in laboratory and pilot plant testing. Regardless of the prospecting technique used, reliable estimates of the yield and grade of phosphate rock that can be extracted from an ore deposit are required: • to justify capital expenditures for a new mine • for mine design and mine planning • for beneficiation plant design • for production forecasts, quality control, and marketing. This paper describes models that predict the beneficiation response of ores from three phosphate ore deposits. The purpose of these models is to obtain maximum utilization of available prospect data with the least cost. ORE DEPOSITS Simple beneficiation models have been developed for ores from three sedimentary phosphate deposits around the Mediterranean area. The first deposit, herein described as "A" ore, is located north of the Mediterranean Sea. The second deposit, designated as "B" ore, is located east of the Mediterranean Sea, while the third deposit, "C" ore, is located south of the Mediterranean Sea. Ore "C" is from the Sra Ouertane deposit in northwestern Tunisia.

Jan 1, 1993

By Rudolf Fahn

Bentonites are best suited for the preparation of acid activated clays with efficient adsorption properties. They are weathering products of acid volcanic ashes and their natural deposits are world-wide spread. The main constituent of bentonite is the aluminium hydrosilicate nontmorillonite with a high ability to swell. Süd-Chemie owns bentonite deposits in Germany and subsidiaries in Italy, Mexico and Arizona.

Jan 1, 1979

By L. Tercero Espinoza, F. Marscheider-Weidemann, C. Gandenberger

"A reliable supply of non-energy raw materials is a precondition for the functioning of the European economy. In line with its importance, the issue of raw materials supply has become more prominent in the past years, especially owing to turbulent raw material markets. However, these turbulences are not due to depletion of the geological resources but to a missmatch of (expected) supply and (expected) demand, with several interacting factors influencing the markets both from the supply as well as from the demand side. A recent evaluation, published in June 2010 within the framework of the EU Raw Materials Initiative, sought to bring together these two sides of raw material markets and asked the question "which raw materials are critical for the EU?" Herein we present the methodology used by the Ad-hoc Working Group on Defining Critical Raw Materials and the results obtained, complemented by results from the study "Raw Materials for Emerging Technologies"."

Jan 1, 2011