Search Documents

By H. Maleki

As mining continues toward deeper reserves in thick western US coal fields, the control of mining induced-seismicity has become a priority in many operations in Utah, Colorado, and Wyoming. Gradual floor heave, common in many coal mines, has historically not been a safety issue. However recent occurrences of sudden floor heave accompanied with seismicity in a few deep mines have fueled this investigation. The focus is to identify and study the mechanisms resulting in sudden heaving of the mine floor in western U.S. deep coal mines through analytical calculations and back analyses of an actual event in a cooperative mine. Based on review of available data in three mines, underground observations and back analyses of an actual event, the authors have identified the following contributing factors (1) presence of stiff stratigraphic units and thick seams mined at depths exceeding 1000-ft (2) presence of geological discontinuities reducing the in-situ strength of the coal with calculated factor of safety near 1 for the mine floor (3) mining approaching areas of higher than normal stress gradient associated with previous mining or structural anomalies or surface topographic highs and (4) an additional source of energy triggering sudden failure such as periodic caving or slip along geological discontinuities. Preliminary examination of seismic data for the actual event in the cooperative mine and underground observations excluded fault slip at the mining horizon as the triggering mechanism but highlighted the significance of weak, anisotropic strata conditions near the intersection of two faults.

Jan 1, 2009

By Gail L. Achterman

Most mining companies today perform site assessments and operational or compliance audits regularly. The purpose of these audits is to review company facilities and operations to determine whether they comply with applicable federal, state and local environmental laws and regulations. Why Audit? Companies adopt assessment and audit programs for legal and business reasons. The business reasons include: (1) ensuring efficient and cost-effective compliance through early problem identification and resolution; (2) planning and implementing business transactions such as real estate conveyances, loans, mergers and acquisitions, and waste disposal service contracts; and (3) employee training and relations. Legal reasons for audits include: (1) avoiding enforcement actions and penalties; (2) meeting environmental permit certification requirements; (3) avoiding corporate officer liability; and (4) meeting Security and Exchange Commission disclosure requirements. The Environmental Protection Agency ("EPA") encourages environmental auditing by regulated entities. The EPA Environmental Auditing Policy Statement was published in the Federal Register on July 9, 1986 (51 Fed Reg 25,004). Although the existence of an auditing program does not create a defense to or otherwise limit a company's regulatory responsibilities, EPA considers compliance programs in setting inspection and enforcement priorities. If a company makes an honest effort to identify and correct its own problems, EPA's enforcement approach is influenced, especially if violations are promptly reported. Perhaps more significant to many executives, the U.S. Department of Justice issued guidelines last year on when it will pursue criminal prosecution for environmental violations. See Department of Justice, "Factors and Decisions on Criminal Prosecutions for Environmental Violations in the Context of Significant Voluntary Compliance or Disclosure Efforts by the Violator," (July 1, 1991). It is now commonplace to read about major companies pleading guilty to criminal violations and paying millions of dollars in penalties. For example ALCOA recently agreed to pay criminal fines and civil penalties totaling $7.5 million for unauthorized excavation of PCB-contaminated soil and improper dumping of spent caustic solution. No executive wants to explain to the Board of Directors or shareholders why the company was criminally indicted. The Department of Justice considers factors such as voluntary disclosure, preventive measures and compliance programs, such as a regular compliance auditing program, the effectiveness of the disciplinary system for employees who violate the company's environmental policies, and subsequent compliance efforts by companies to remedy ongoing noncompliance. The Department of Justice looks closely at whether audit recommendations were implemented in a timely way and whether environmental compliance was a standard by which employees were judged. The Lawyer's Role. The role of the lawyer in an audit team deserves special attention. When enforcement action or litigation has begun or is contemplated or a government agency has asked for information, attorneys always should be directly involved in environmental audits. In most situations, however, environmental audits are management tools, and the attorney's role should be to advise the team. The attorney can help make sure the team understands the laws and regulations the facility must

Jan 1, 1992

By K. Boakye

This paper presents the results of a review of historic blast design practices at the Dragon Products Company, LLC (Dragon) Quarry Operation, along with the results of two different blast design vibration monitoring programs. A blast pattern design modification was initiated to determine if production volume per shot could be increased and highwall instability could be decreased. A vibration monitoring program was undertaken to investigate peak particle velocity (PPV) and relate the data to the blastability of the jointed onsite rock mass, utilizing the relationship between PPV and dynamic stress and strain. The Dragon Quarry Operation has historically used a 6-in. diameter, 14-ft by 14-ft production blast pattern, with blast holes loaded manually using cartridge style explosive products. In 2011, Quarry Operations introduced a 6-in diameter, 16-ft by 16-ft production blasting pattern, using pre-mixed, truck-loaded, bulk emulsion/ammonium nitrate/fuel oil (ANFO) blends. This paper summarizes the results of the blast design modifications, the results of the vibration monitoring data, and describes how production blasting and excavation at the Dragon Quarry has benefited from such modifications.

Feb 27, 2013

By A. B. Cecala, G. W. Klinowski

Introduction The US Bureau of Mines has designed and evaluated total mill ventilation systems (TMVS) at two mineral-processing operations. Both systems have proven proficient at cost-effectively reducing respirable dust levels throughout the mills. An 11.8-m3/sec (25,000-cfm) system installed at a clay-processing mill provided about 10 air changes per hour (acph). This system reduced respirable dust concentrations by about 40% throughout the mill building. The second evaluation was performed at a silica sand operation. Tests were performed with 23.6 and 47.2 m3/sec (50,000 and 100,000 cfm) of ventilation to the mill building, corresponding to 17 and 34 acph. Average millwide respirable dust reductions were 36% and 64%, respectively. This work was done to determine general guidelines and design criteria for operations that may be interested in implementing TMVS. TMVS should be designed to draw clean make-up air in near the base of the mill. This air provides general purging and may clear some dust-laden areas throughout the mill structure. It is discharged at or near the top of the structure. Without the TMVS, dust can exit the building through open doors, windows, etc. and contaminate outside plant workers. This dust can also be recirculated back into the mill building causing additional contamination problems. TMVS is not a stand-alone system. It is a supplemental technique to assist other localized dust control systems (Mody et al., 1987). Testing Total mill ventilation systems were evaluated at two processing operations. For both tests, the primary goal was to determine the reduction in respirable dust throughout the structure. Test site No. 1. The first evaluation was performed at a clay-crushing and screening mill in New York. The mill's base dimensions were 39.6 x 9.8 m (130 x 32 ft), giving a volumetric capacity of 4250 m3 (150,000 cu ft). The TMVS was designed to provide 12 m3/sec (25,430 cfm) of ventilation air to the mill, representing about 10 acph. This was accomplished by three 4 m3/sec (8475 cfm) roof-powered exhaustors that were evenly spaced across the roof. Three wall louvers provided inlets for make-up air at the mill's base. Two evaluations were performed at this mill. The first occurred for two days in December when outside air temperatures ranged from -12.2° to 4.4° C (10° to 40° F). Temperatures with the wind chill factor dropped as low as -34° to -40° C (-29 to -40° F) during the early morning. The second evaluation was in April when outside air temperatures ranged between 10° to 26.7° C (50° to 80° F). These two evaluations verified the effectiveness of TMVS in lowering respirable-dust concentrations throughout the mill. Gravimetric-sampler respirable-dust concentrations in December ranged from 0.22 to 2.39 mg/m3 under normal conditions, compared to 0.13 to 1.55 mg/m3 with TMVS. In April, respirable dust concentrations ranged from 0.29 to 4.84 mg/m3 under normal conditions compared to 0.21 to 2.37 mg/m3 with the system on. TMVS also increased visibility throughout the mill building. Dust reductions for gravimetric and RAM-I instruments are listed in Table 1. Each value was determined by comparing the average concentration for the entire day of testing for normal and TMVS values. The mean/standard deviation values for gravimetric and RAM-1 results were 42.5/17.6 and 37.1/16.8, respectively.

Jan 1, 1996

By L. E. Sausa

Measuring the specific gravity of a pulp in concentrating plants is a relative, y simple procedure, but the desired accuracy is often difficult to attain. Many plants use the system of weighing a known volume of the pulp on a scale. In many cases, this method is quite accurate, but obtaining a true sample presents quite a problem. This is especially true when the pulp tends to froth, the solids settle rapidly, or the flow is fast at the point of sampling. There is also the problem of the operator neglecting to take the sample because of duties elsewhere, or, if everything Is apparently running smoothly, he assumes the pulp density is also all right. In 1952, the Pine Creek plant of Union Carbide Nuclear Company began working on a better method for measuring and controlling pulp density. After an extensive investigation of different methods for measuring the specific gravity of moving pulps, the Research Department decided that the bubble tube method appeared to be the simplest and most promising for our applications. It consists of two bubble tubes, of different lengths, submersed in a pulp. Low pressure air is supplied to, the two tubes through sight bubblers to maintain approximately equal volume of air to each bubble tube. The bubble tubes are also connected to a differential manometer, one to each side. Therefore, knowing the vertical distance between the outlets of the bubble tubes, the manometere can be calibrated to measure directly the specific gravity of the pulp. (Figure No. 1 illustrates this model.)

Jan 1, 1960

By W. J. Aitken

The pneumatic conveying of relatively large abrasive materials by dilute-phase conveying techniques has been applied in the underground mining industry for many years especially for backfilling mines and the hoisting of ore, coal, or rock out of the mines. The technique was extensively used in Europe, especially Germany and Britain for backfilling coal mines with rejects from the coal cleaning plants which not only helped to reduce environmental problems on the surface, but offered support to the overlaying strata in the deep underground mines, Similar techniques are being employed in the U.S.A. especially in uranium mines for the disposal of tailings, the main purpose being to extract a larger percentage of the ore from the pillars especially under weak roof conditions. Other than for the backfilling of abandoned mine entries, pneumatic conveying has not been applied in the mining industry in surface applications. In this paper, some consideration is given to three applications for open pit mining which may prove beneficial, namely hoisting coal up the high wall, sealing off auger holes, and stabilizing the high wall when being undercut by a longwall system.

Jan 1, 1981

By James N. L. Lukanuski

Three porphyry copper districts in southern Arizona are partly overlain by post-ore fanglomerates which share certain physical and petrologic characteris¬tics and which may comprise a distinct and significant class of rock. These units are the Locomotive fanglomerate of Ajo, the Helmet fanglomerate of Twin Buttes-Mission-Pima, and the Cloudburst formation of San Manuel-Kalamazoo, termed "Locomotive-type fanglomerates" herein. Post-ore units at Poston Butte and Lakeshore, Arizona, and Sar Chesmeh, Iran, also appear to fit this class. "Locomotive-type fanglomerates" are composed of poorly sorted conglomerates, lenticular sandstone beds, andesitic to rhyolitic flows and tuffs, and unique monothologic landslide breccias. They contain fragments of holyokeite - - a rare oligoclase lava of porcellaneous appearance. Their basal contacts are considered to be depositional and overlapping, sometimes complicated by later low-angle faulting. They arc quite different than the younger Cila, Pantano, and most "Whitetail" alluvial beds, and the older Amole, Recreation, Claflin Ranch, etc. elastics; in particular they are thinner and less widespread. Their ages are Eocene to late Oligocene. "Locomotive-type fanglomerates" may be genetically related to porphyry coppers as products of subsequent differentiation and volcanism, and sedimentation in short-lived basins of restricted area and extreme relief. They might be utilized as reconnaissance guides to target areas and as structural guides within target areas in the southwestern U.S., Northern Mexico, and elsewhere.

Jan 1, 1975

By Kevin Andrews, SETAREH GHAYCHI AFROUZ

Ground control analysis and groundwater inflow assessments for underground coal mines require in-depth field investigations including, but not limited to, geological and geotechnical core logging, downhole geophysical logging, laboratory rock strength testing, and packer (Lugeon) testing. Field and laboratory data collection are time consuming and expensive, and an initial understanding of the expected trends among various geotechnical and hydrogeological parameters can assist with the planning and optimization of geotechnical characterization studies and grouting plans. In this study, a comprehensive database is analyzed, comprised of important rock mass characteristics (hydraulic conductivity, rock quality designation (RQD), and lithology) for coal-bearing rocks in the Central Appalachian Basin. Statistical analysis of the data is completed to establish an enhanced understanding of geotechnical and hydrogeological conditions expected to be encountered as underground coal mining passes near and beneath streams and rivers. The results of the study provide valuable reference material for the coal mining industry for completion of shaft installations, mine stream crossings, environmental assessments, and grouting and mine dewatering designs.

Jul 1, 2023

By R. H. King

This paper describes the results of an underground coal mine trial installation of a shielded trailing cable. The cable was a three conductor, round, type SHC-GC, and was installed on a shuttle car in a conventional room and pillar mining section. The purpose of presenting the information is to prepare mine operators for proposed legislation that will require shielding on low-voltage trailing cables. Specifically, machine modifications are required to cable reels, packing glands, and couplers. Cable splicing is not as complex as expected but additional materials are needed in the kit and splice training is necessary. Even though shielding will cause some problems for the mine operator, it can reduce the hazard of electrical shock to mine workers. This paper will present information that mine operators can use to solve most of the problems that will be encountered if they are required to install shielded cables. The in-mine evaluation was funded by the U.S. Bureau of Mines.

Jan 1, 1980

By John T. MacWaters, George H. Milly

INTRODUCTION This paper describes operational procedures and instrumentation which were developed to implement a patented method of detecting and locating uranium ore bodies. All equipment was designed for accurate and reliable use under difficult field conditions. Data resulting from these developments, some of which are incorporated in a companion paper for this conference*, have contributed to our understanding, of the nature and significance of naturally-occurring radon exposures. Further applications of these techniques may prove useful in studying anthropogenic radon in evaluating the significance of variability in radon flux, or in taking proper account of the contribution of natural radon to ambient radon concentrations, particularly in mineralized regions. OPERATIONAL PROCEDURES The uranium search technique employed by GEOMET begins with a [reconnaissance mode], which utilizes a series of ambient air filter samples taken from a moving or standing vehicle to detect anamalous concentrations of radon. These samples are normally taken at night under stable (temperature inversion) or neutral atmospheric conditions, to avoid the rapid dispersion of the radon clouds typical of daytime turbulent conditions. Radon daughters formed by the decay of radon quickly attach to ambient aerosol particles and are captured on the surface of a membrane filter during a five-minute sampling period. The filter is placed in a portable alpha scintillation counter, and a five-minute count is started at a preset time after the completion of the sampling period. This count is followed immediately by a second five-minute count to enable determination of the cloud age, based on consideration of the relative half-lives of the initial radon daughters. With the use of tables computed from the mathematics of the uranium decay process, and with the measured radon background accounted for, the first and second counts are used to estimate the time which has elapsed since the pure radon initially emanated from the earth's surface. This cloud age, combined with wind speed and direction measurements made at the beginning and end of each sample, as well as with an understanding of the effects of local terrain features on wind trajectory, provides an estimate of the Probable location of the source. In practice the reconnaissance mode involves one vehicle with a single operator to take the five-minute samples, moving or standing, along any available roads or trails in the area to be covered. Under the usual nighttime stable conditions the cool air flows downslope and downvalley, and the operator will pay special attention to locations along the axes and confluences of the natural downflow patterns. These facilitate sampling of large air drainage areas. Successful detection of sources of radon based on high concentrations of radon daughters, and substantiated by evidence of "fresh" clouds, are frequently made on the basis of a relatively few samples taken judiciously by an experienced operator during a reconnaissance. At this point he has a choice: he can continue to cover the designated reconnaissance area, leaving the localization of any anomalous radon detections to await the ranking of detections by priority, or he can continue with localization of the detected source, either alone or by radioing for another vehicle to assist in triangulation operations. Localization of a source involves skillful and experienced use of the continuously collected data on concentration, age, and wind speed and direction, together with knowledge of the terrain from observation and contour maps, and exploitation of the available roads. Since age ratios are dependent solely on proximity of the source and wind speed, decreasing [cloud ages] based on statistically significant increasing age ratios represent the most useful. information in localization. The [magnitude of the concentration] of radon daughter products is also useful; however, it may vary widely for a variety of reasons during sampling for a localization, thus making this a secondary parameter for localization. Large values of concentration are of course useful; typical results for successful detection of a strong anomaly would yield alpha counts ranging from 10 to 25 times background values. These counts are convertible to ambient radon concentrations by appropriate consideration of the decay process. Successful localizations of radon sources using this procedure with ambient atmospheric measurements normally will narrow a source location to within an area ranging in size from less than a quarter of a square mile to at most a square mile, and frequently give information on the probable shape of the source (in plan view) on the earth's surface. Judicious use of this procedure could undoubtedly provide finer localization, but the coarser results just described are adequate for this Phase of GEOMET's uranium exploration procedures.

Jan 1, 1981

By Isabel F. Barton, Matthew J. Gabriel, CARSON ROBERTS, JOHN LYONS-BARAL, LEON DUPLESSIS, Mark D. Barton

Geometallurgical characterization is increasingly used in the mining industry to model ore types, predict process performance and identify potential recovery issues ahead of time. However, most geometallurgical assessments are based on bench- or laboratory-scale analyses of relatively sparse samples, leaving most of the orebody characteristics known only by inference until the rocks are actually mined. In this pilot study, we test drone- and tripod-based hyperspectral imaging for mapping mineralogy across mine highwalls, dumps and leach pads. The results show that hyperspectral imaging can successfully map the types and distribution patterns of key minerals (especially carbonates, sulfates, clays, other phyllosilicates) and other important features (such as lixiviant ponding on leach pads), bringing geometallurgy into the field to provide crucial inputs to process decisions.

By C. J. Bise

Virtual Reality (VR) is a concept in which the human experience of perceiving and interacting with a computer-modeled environment is achieved through the use of sensors and effectors. It is an advanced fonn of computer graphics where the images are generated based upon where the user looks and how the user moves. As personal-computer-based (PC-based) instruction gains acceptance as an innovative approach to providing safety training, VR offers the capability of providing a multisensory, rather than merely a multimedia, mode of presentation. VR has been effectively used by the military for training tank commanders and by hospitals for training surgeons. However, these applications have been limited to small numbers of highly skilled participants. The purpose of this paper is to examine VR's potential for enhancing the hazard awareness of larger numbers of individuals in a broad-based approach to mine safety training, such as new-miner, annual-refresher, and independent-contractor training.

Jan 1, 1996

By Bernd Friedrich, Elif Emil‑Kaya, Merve Papakci

In the production of SmCo permanent magnets with excellent temperature stability, corrosion resistance, and oxidation resistance, samarium (Sm), one of the rare earth elements (REEs), and cobalt (Co) are employed. Cobalt (Co) is a crucial component in tool materials, nickel-based alloys, tablet and smartphone batteries, and electric car batteries. REEs and Co have been listed as critical raw materials by the European Union Commission for many years. Due to the ever-growing demand for Co and REEs in technological applications, the recovery of these elements from secondary sources has garnered significant interest. There are two types of SmCo magnets, one of which contains a high amount of iron, approximately 15.2%. This paper focuses on the recycling of Fe-bearing SmCo. In this study, an oxidative leaching process with nitric acid was developed to eliminate iron through in situ hydrolysis and to dissolve REEs and Co. The influence of experimental conditions on the formation of an amorphous iron compound through the hydrolysis of Fe3+ in a nitric acid environment was thoroughly examined based on a Taguchi orthogonal array. The optimal parameters for oxidative leaching were determined to be an acid concentration of 3 mol/L, a solid-to-liquid ratio of 1/10, and a process temperature of 60 °C.

Feb 15, 2024

By E. L. Michaels

Laboratory and pilot scale tests have been made to deter- mine the utility of heavy media separation, particularly a cone type separator, as a means of recovering aluminum from shredded municipal solid waste. The effect of the method of shredding on the behavior of aluminum in a heavy media system was deter- mined. Two-stage pilot scale heavy media separations were made with size fractions of shredded refuse. Recoveries of aluminum, as well as other components of the refuse, were measured and medium losses were determined. The experimental results indicate that with certain reservations a heavy media cone system can be utilized for aluminum separation and recovery from shredded and air classified municipal solid waste. Observations made using two-stage heavy media separation in a drum unit are included. Qualitatively, the results from the two types of separators are similar.

Jan 1, 1974

By Charles A. Bankston, John C. Rowley, Robert J. Hanold, Joseph W. Neudecker

The basic concepts and processes of soil and rock melting as applied to excavation technology are reviewed. The electrically heated, small diameter prototype penetrator development sequence is presented. Emphasis is placed on the different methods of handling the fluid rock and soil melts and their significance in providing new solutions in hole support and debris handling problems. The refractory materials requirements, penetrator life and electrical heater technology are presented. Consolidating penetrators, which form stable glass-lined holes in low density rocks and soils, require no debris removal and will find applications in horizontal holes for utilities, cables, and pipeline installations. Extruding penetrators are being developed to make holes in dense, hard rocks. Melt is conditioned into a variety of debris forms, i.e., glass rods, pellets or rock wool, selected to match appropriate debris handling systems. Unique use in drilling into very hot rock or magma for geothermal exploration or production wells is projected. Some of the results of laboratory and field tests of these devices are compared with theoretically derived operating performance. Coring-consolidating penetrators for geological sampling in alluvium are projected to larger diameter self-propelled and guided coring devices for prospecting along proposed tunnel alignments. Application to the melting of annular shafts for pipeline support piles in difficult conditions such as permafrost has been scoped. Conceptual design studies of large diameter tunneling equipment have indicated the system contributions and economic aspects of rock melting relative to material comminution, wall and roof support and materials handling.

Jan 1, 1974

By D. C. Sisti

A paper was presented during the 1970 SME Fall Meeting on the Stinson Preparation Facilities by representatives of Beaver Creek Consolidated Cool Company and Heyl & Patterson, Inc. This paper summarized a combined approach to development of a flow diagram and selection of cleaning equipment required to produce a uniform metallurgical coal at maximum recovery with special emphasis on sulphur reduction. These facilities were located in the Elkhorn. Coal Fields of eastern Kentucky and, in particular, the area of Wayland, Knott County, Kentucky, where approximately forty-five- million tons of Elkhorn No. 3 coal could he recovered. The facilities incorporated a Bradford Breaker for reduction of the ROM coal to minus 1-1/2 x 0, 6000 ton-raw coal storage, preparation plant, water clarification and thermal drying facilities, clean coal storage and a 4000 TPH unit train loading facility.

Jan 1, 1973

By A. C. Lyons

Foreword Sir William Halcrow and Partners are responsible for the design of the Ahmed Hamdi Tunnel as Sub-contractor to the Contractor, Osmac, a joint venture formed by the Arab Contractors, Osman Ahmed Osman and Company of Cairo, and Tarmac International of London. Throughout the paper the term "Client" refers to the Employer, the Ministry of Housing and Reconstruction, which latterly became the Ministry of Development and New Communities of the Arab Republic of Egypt. At the time of writing of this paper only a few hundred metres of the tunnel have been driven, but the design is substantially complete. Introduction The Ahmed Hamdi Tunnel, which is at present under construction, will be a two-lane tunnel crossing beneath the Suez Canal approximately 15 km north of the town of Suez at El Shallufa. It will become the first permanent connection across the Canal since 1967 and is visualised by the Egyptian Government as an early step in the development of the Sinai Desert along the eastern bank. The tunnel will carry pipelines for treated water and electric power cables to assist in this development. The tunnel, which will be 1640 m in length, is being driven through hard clay and mudstone using a tunnel shield fitted with hydraulic excavators. The primary lining is being constructed with precast, bolted reinforced concrete segments with an internal diameter of 10.4 m. The road deck structure and the walls of the air supply ducts beneath it are formed with precast, reinforced concrete units erected immediately behind the shield.

Jan 1, 1979

By R. Snoby

Since its introduction in 2002, the modern air jig has processed a wide array of coals throughout the world. This paper explores the reasons and justifications for the installations and provides case history performance data. Specifically highlighted are air jig plants processing metallurgical coal in Colombia, bituminous coal in the United States and India and lignite in the United States and Spain. Each installation has unique reasons to justify an air jig facility. It is important to note that not all of the justifications were based on the ?most cost effective yield?, normally a mantra for coal preparation plant designers and owners. Dry jigging of coal has long been a proven technique for upgrading coal, the modern air jig, with its improved efficiency and operating systems simply extended the range of applications. In some cases, it even allows market quality coal to be produced when no other option is possible.

Jan 1, 2009

By J. R. J. Edwards

Jaspilite, a mineral consisting of silica and iron oxide in varying proportions, is one of the host rocks of the high grade ore deposits situated in the Middleback Range of South Australia. As a result of laboratory investigations, a flowsheet was postulated for the beneficiation of jaspilite to produce an acceptable grade product for feeding to blast furnaces, The flowsheet involved the reduction of the hematite in the haspilite to magnetite, the grinding of the reduced product to 95 pct minus 325 mesh Tyler followed by wet magnetic separation, hydroseparation and filtration to yield a magnetite concentrate. Agglomeration of the fine concentrate would then be necessary to meet the physical requirements of blast furnace feed. To prove the postulated flowsheet, to obtain a more accurate estimate of costs and to obtain design data for a commercial installation, a pilot plant was constructed at Whyalla, South Australia.

Jan 1, 1960

By F. T. Paleari

Radial gas holdup profiles have been measured in a 50x400 cm flotation column using a multi-cell conductivity probe. Three different bubble generation systems were examined: up to eight vertical filter cloth spargers, three horizontal filter cloth spargers, and three (horizontal) Cominco-type spargers. The variables tested were: number of spargers, symmetry of their arrangement, and height above spargers. Batch water with up to 20ppm frother concentration was used. The general observation is that the profiles tend to be uniform (i.e. flat) with some exhibiting a slight wavy shape. The vertical sparger arrangement proved the most difficult to achieve profile symmetry. The horizontal spargers gave uniform profiles at right angle to their length but a decreasing gas holdup along their length; the Cominco-type spargers gave slightly less scatter in the data. Switching off selected spargers (to simulate malfunction) did not produce strong asymmetry in the profiles.

Jan 1, 1993