Search Documents

By W. C. Dailey

The National Steel Pellet Company is owned by National Steel Corporation, managed by the M. A. Hanna Company and located near the town of Keewatin in northern Minnesota. Annually, the concentrator processes 15.24-Mt (15.0 million It) crude taconite with eight 8.2-m diameter by 5.5-m long (27 ft x 18 ft) wet semi-autogenous (SAG) mills to produce 4.57-Mt (4.50 million It) of iron ore pellets. To improve operating costs and primary mill grinding circuit efficiencies, a task force on liners was formed with the operation, maintenance and engineering staff at N.S.P.C. along with the local supplier of mill liners. Results of the task force recommendations since 1980 along with improvements made in the primary circuit operations, are presented. Mill Liner Design and Metallurgy Changes The primary mill liner task force was formed in 1977. Its function was to improve the operating costs and milling efficiencies of the ten 8.2-m x 5.5-m (27 ft x 18 ft) wet SAG mills that were operating at the time. The SAG mills are driven by two 3500 HP motors drawing a total of 5450 kW at 76% of critical speed.

Jan 1, 1985

By Arash Habibi, Anna Cable, David Loring, Aleksandar D. Bugarski, Logan Ingalls, Calvin Rutter

The results of diesel particulate matter (DPM) monitoring were used by the underground mining industry to mitigate adverse effects of exposure to DPM. NIOSH Method 5040, currently used for ambient and personal exposure monitoring, does not provide needed real-time information. The objective of this study is to develop a methodology for continuous monitoring of DPM concentrations in an underground environment, founded on the application of the Dekati electrical particle sensor (DePS). The DePS, which measures concentrations of submicron aerosol in real time using a diffusion-charging sensor, was evaluated by comparing the results of the concurrent measurements with reference methods at several locations downstream of the diesel-powered equipment. The DePS results were found to correlate well to those obtained by reference methods. However, it was found that dependence of the response on the physical and chemical properties of aerosols necessitates sitespecific correlation factors for the targeted matrices. The site-specific factors for number and mass of diesel aerosols were derived using the results of concurrent measurements with TSI NanoScan, FLIR Airtec, and carbon analyses performed on the concurrently collected filter samples. The results showed that methodology based on compensated DePS measurements would be suitable for continuous monitoring of DPM in underground mining operations.

Dec 1, 2022

Water and wind erosion of toxic zinc and lead smelter waste is one of the most urgent environmental problems to be solved in the Silesia region of Poland. Over 87 x 106 Mg of various mining wastes were disposed of in uncontrolled piles leading to soil, water, and air pollution in highly populated areas. Welz and Doerschel process Pb/Zn smelter wastes were stabilized in the summer of 1994 by application of heavy loads of CaCO3 (30 Mg/ha), CaO (1.5 -15 Mg/ha), and municipal biosolids (150 -300 Mg/ha), followed by seeding with a mixture of acid-and salt-tolerant grass species selected in a pot experiment. Vegetation was successfully established on 85% of the Welz material demonstration plot area (0.5 ha), even though it was initially high in water-soluble Zn, Pb, and Cd ranging from 0.4 to 1311,0.1 to 5.8, and 0.05 to 55 mg/kg, respectively. Standing biomass averaged 3.3 Mg/ha on the stabilized Welz waste zone by the end of the third growing season (1997). The revegetation of much of the Doerschel material area failed initially because of extremely high salinity (16 dS m-1), high content of water soluble metals (Cd in particular), and heavy compaction. The area was capped (15 cm) with waste lime and retreated with bio-solids (300 Mg/ha) in 1995, and standing biomass averaged 2.9 Mg/ha in the fall of 1997. The observed plant response to bio-solids and lime indicates this approach to be an environmentally beneficial technology as compared to the traditional methods utilizing topsoil covers.

Jan 1, 1999

By Richard R. Klimpel

The first part of this two-part article summarizes the result of a 10-year, multimillion dollar research and plant testing program involving operating mining companies throughout the world. The program was aimed at developing a better understanding of the influence of slurry rheology on the performance of mineral/coal grinding circuits. Part 1 presents the basic concepts identified, including typical laboratory results showing the influence on grinding behavior of controlled changes in percent solids, particle size, slurry temperature, and viscosity control chemicals. Part 2, in January, will illustrate typical industrial scale test results on both open and closed circuits using the concepts presented in Part 1. Special emphasis will be placed on identifying some industrial operating implications of controlling rheology by different methods. Introduction The industrial-scale practice of wet grinding minerals and coals in tumbling media mills (ball, rod, and pebble) is well-known to operating mineral processing engineers and plant design personnel. Over the last century, considerable experience and data has been collected, correlated, and put into rules or guidelines for successful circuit design and operation. Typical factors influencing circuit throughput that have been analyzed in some depth are mill diameter and length, grinding media size and loading, feed and product particle size, mill power use, and the interaction of classifier type and efficiency with the grinding device. Until recently, knowledge of slurry rheology influence on large scale grinding circuit performance has been limited. Even today slurry rheology effects are essentially ignored in plant design. Indeed, in most plant operations only qualitative guidelines are followed. For example, too thick a slurry causes throughput losses and too thin a slurry uses excessive water or causes water handling problems such as pumping limitations. A search of published literature and numerous discussions with experienced plant operating personnel has shown an awareness that changing the percent of solids in the mill influences grinding or the response of grinding involving fine feeds versus coarse feeds. However, most the work identified relative to rheology effects in mineral/coal grinding was qualitative. Even in the few studies that were more quantitative, the scope of the work was usually too narrow to draw general conclusions. Also, the detailed rheological characterization tied to observed breakage and the combination of laboratory to industrial-scale testing that is required to develop a broad understanding of any factor influencing grinding had not been done. In this environment, this detailed program began in 1967. It had three distinct goals: • To develop a basic understanding of slurry rheology influence on breakage characteristics in the laboratory. • To test general rheology concepts developed in the lab on the industrial scale. • To develop a commercially viable chemical approach to controlling slurry rheology that would lead to the use of chemical grinding additives or grinding aids. The goals have been met, at least in part, this year. A small fraction of the extensive laboratory and plant results have been made available in published literature. Much of the research program dealt with identifying and developing chemical grinding aids, but a lot of useful and practical information on percent solids, particle size, and slurry temperature influence on grinding circuit performance also was collected. The purpose of this article is to present a clear and concise sum¬mary of the results of the entire program. The importance of rhe¬ology control in grinding circuit behavior will be demonstrated using a series of carefully per¬formed industrial scale experi¬ments (both open and closed cir¬cuits) that have not yet been reported in general literature. Mining companies participating in the test program on a proprie¬tary basis have found the informa¬tion in this article to be useful in better understanding and improv¬ing circuit performance. Viscosity Effects in Grinding Studies In this program&apos;s previous labo¬ratory studies, it was shown that there is a consistent pattern of change in specific rates of break¬age of both mineral and coal slur¬ries as slurry fluidity changes. Using the net production rate of material smaller than some spec¬ified size-for example, kg/hr of <75 µm (200 mesh)-as an index of mill production in a standard batch mill test (with a given feed material, feed size, mill, and mill conditions such as constant time of grind), the following facts were established (see Fig. 1): • The normal range of low den¬sity, low viscosity slurry (region A) gave no variation in mill produc¬tion. The measured rates of break¬age exhibited normal first order grinding. • Grinding of a somewhat higher viscosity slurry (region B) could give increased production. The higher viscosity was obtained

Oct 12, 1982

By M. Sadegh Safarzadeh, Stanley M. Howard

The two-dimensional predominance area (Kellogg) diagram (PAD) surfaces bounding the three-dimensional Cu-As-S-O system were constructed at 900 K. The computations employed gases As4O6(g), O2(g), and SO2(g) as the independent coordinate species to generate diagrams of As4O6(g) − O2(g),O2(g) − SO2(g), and As4O6(g) − SO2(g), while the third gas (As4O6, O2, or SO2) was fixed. The results indicate that there is no shared boundary between enargite (Cu3AsS4) and copper sulfate (CuSO4); however, at PO2 < 10−6 atm, PAs4O6 < 10−10 atm, and PSO2 > 10−4 atm, CuSO4 is the stable phase at 900 K. The chemical driving force for oxidation of intermediate phases between enargite and copper sulfate is substantial except for basic sulfate (CuO · CuSO4).

By R. K. Singhal

In an underground coal mining environment, a frictional ignition may be defined as the ignition of an explosive air/ methane/coal dust mixture by mining machinery. As the use of power loading equipment has become more widespread, frictional ignition incidents have increased. There have been many fatalities and injuries from this cause including the death of eleven miners in Sydney coalfield of Nova Scotia, Canada in 1979. This paper reports on the findings of a preliminary study carried out under the auspices of the Coal Research Laboratories, Department of Energy, Mines and Resources Canada. The objective of this study has been to identify a Longwall face cutting system that is inherently safer than the conventional shearer loaders used in Nova Scotia.

Jan 1, 1985

By J. A. Cremeens, D. D. Overton, J. C. Varnier

"Slope failures that occurred in 2008 and 2009 at the Pikeview Quarry in El Paso County, Colorado, USA were investigated using three-dimensional discrete element modeling methods. Large scale block sliding failures occurred along weak bedding planes that dip steeply into an excavation located at the toe of the slope. Several mining sequences at the toe of the slope were simulated to evaluate the effects of various degrees of extraction and backfill on slope stability. Slope stability back analysis was conducted using pre-failure and post-failure conditions to determine the joint shear strength properties. Laboratory testing was also conducted to determine intact rock properties. Three-dimensional discrete element analysis was uniquely applicable to this evaluation because it allowed representation of shear stress of the basal sliding surface and it afforded evaluation of several scenarios of extraction and backfill at the toe of the slope. INTRODUCTION The Pikeview Quarry is an aggregate quarry located approximately five miles northwest of Colorado Springs in El Paso County, Colorado, USA. The quarry has been operated by several owners since the early 1900s. The Pikeview Quarry has been a major source of construction aggregate for the Colorado Springs area for many years (MSHA 1986). In the 1950s, the site was mined by Peter Kiewit and Sons to provide limestone for the construction of the nearby Air Force Academy. A large scale slope failure occurred on December 2, 2008, which stopped mining activity at the Pikeview Quarry. A second, related slope failure occurred on September 13, 2009. The second slope failure was located immediately adjacent to the initial December 2008 failure. The objective of this publication is to discuss the three-dimensional slope stability evaluation. The causal relationships of slope instability are not within the scope of this publication. However, omitting the precursors to slope failure would limit understanding of the nature of the slope stability evaluation. The regional and local geology and the history of slope instability at the Pikeview Quarry aid in understanding these precursors. Two main failure mechanisms were hypothesized during the failure investigation to explain the triggering of the 2008 and 2009 large slope failures at the Pikeview Quarry. Both mechanisms are given equal credence in this publication. Quarry excavation was a key factor in the slope instability for both failure mechanisms. The objective of the three-dimensional model was to evaluate the effects of extraction and backfill at the toe of the slope with respect to slope stability. GEOLOGY Regional and local geology are both important factors in slope instability at the Pikeview Quarry. Geologic structure at the quarry is related to regional mountain building and basin development associated with the Laramide Orogeny and the Rocky Mountains. Lithologies at the Pikeview Quarry are also related to regional trends. Localized geologic features, primarily related to weathering and erosion, have also been major contributing factors to slope instability at the Pikeview Quarry."

Jan 1, 2017

By Sandip K. Mukherjee

This paper describes the application of pressure foam to control respirable dust in a double-drum longwall mining section. The feasibility of passing an adequate quantity of pressure foam through the shearer drum was initially established in the laboratory. Thereafter, underground testing of the foam system to determine its effectiveness on an active operating longwall was conducted in a mine in West Virginia. The foam system proved superior to the water spray system. The de- tails of the laboratory and field investigations, the results obtained, and the degree of acceptance of this system by the mining company are discussed in this paper.

Jan 1, 1984

By F. Brost

In 1976, a decision was made to install a conveying system to transport ore 10.3 km (6.4 miles) from the new Eisenhower Partnership Mine to Twin Buttes. The system, supplied and installed by Cable Belt Limited, of England, represents a radical departure from conventional conveyor systems. The driving tension is applied through two endless wire ropes while the belt acts only as the carrying medium. Features of the system are a single 2240 kw (3000 hp) drive and a 60° angle bend. Construction was completed in two years. Full production was attained after several months&apos; operation.

Jan 1, 1979

By Yuting Xue, Danqing Gao, Brijes Mishra

Heterogeneity and discontinuity significantly affect rock strength. For accurate stability prediction, intact rock behavior is imperatively included in rock mass behavior. However, past research largely used arbitrary scaling approaches to produce rock strength. This paper considers a stochastic approach in order to determine the strength of a rock. Based on the laboratory data, a MATLAB® with extreme value stochastic model generates a database for each physico-mechanical property. Then FLAC® simulates laboratory-sized rock specimens. The grids developed in the numerical model can in turn develop random material properties in MATLAB®, which researchers then applied to the final FLAC® model. Model runs simulate the approach performed in the laboratory. The results from the model indicate that a stochastic approach produces strengths that are lower than a deterministic approach. Failure modes for each specimen are different, similar to observations in the laboratory. In addition, random density also influences the failure mode, highlighting the importance of stochastic analysis in rocks.

By Angela Binder, Oliver Langefeld

"The future of mining will be characterized not only by the application of modern technology, but also by the harmonization of economic, environmental and social issues. These areas set major future challenges which are complex and demand extensive knowledge. As an example, mining of highly complex orebodies for the supply of often critical raw materials, needs to consider technically demanding and cost-intensive extraction issues. The amount of tailings, which need to be stored, increases with the amount of ore mined. Therefore, the negative impact on environment and society increases. Hence mining becomes expensive with regard to all three aspects: economy, environment and society. In view of a sustainable mining practice this challenge should be used as an opportunity. The positive impact should be maximized for present and future generations. The objective is to create and use the mining openings in an optimum way related to sustainability. The approach of Blue Mining, which focuses on energy and ergonomics in the field of Sustainable Development, enhances the closure planning by recommending subsequent usage of such openings for energy storage. The approach fosters among others the implementation of the 7th Goal for Sustainable Development defined by the United Nations with the assurance of access to affordable, reliable, sustainable and modern energy for all. The usage of underground storage increases the stability of solar and water power usage, which are otherwise unreliable. Blue Mining embeds these issues in the main planning effort long before groundbreaking. This approach involves experience from past and current projects. This paper introduces the concept of Blue Mining with respect to post-mining utilization of a mine for energy storage. Methods and perspectives are presented with examples covering best-practices and lessons-learned."

Jan 1, 2017

By H. Fayed

Froth flotation technology is the backbone of the minerals pro-cessing industry where minerals are concentrated by selective separa-tion; either direct or in-direct flotation. In direct flotation useful minerals are conditioned to become hydrophobic (water-repellant) and attach to air bubbles while impurities (non-useful particles) remain in water. The hydrophobic particles are transported by air-bubbles to the top froth (foam) layer in flotation tank which can be removed as a concentrate. There are many factors that controls this selective separation process such as: particle’s degree of hydrophobicity, size, mass loading, air holdup and bubble size distribution. Turbulent fluctuation of the slurry in the tank is another important factor that controls the collisions rate between particles and bubbles and hence attachment rates. The turbu-lent fluctuations are measured by the local distribution of turbulent dissipation rates. Conventional flotation machines are restrained by residence time of the slurry that is about 3-5 minutes that results in a large footprint and limits the capacity of flotation plants. The designers of conventional flotation machines try to reduce the footprint of flota-tion tank by scaling up the flotation machines to increase plant throughput. The scale-up process reduces the specif power consump-tion and the local distribution of shear rates and turbulence dissipation rates. This scale-up results in a larger mean bubble size and lower particle-bubble attachment rates.

Feb 1, 2023

By R. D. Grove

The control of Florida phosphate flotation plants is largely based on the visual observations of experienced operators, both in recognizing good and bad froth conditions and in making judgments about the composition of feed, concentrate and tailing streams. Chemical analyses lag the process by at least two hours and therefore only assist in recalibrating the operators&apos; vision when major deviations occur. An image analysis system has been developed by IMC Fertilizer to improve upon the accuracy and precision of the composition estimation process. It still relies upon the operator taking a representative sample, but provides a measurement in about 15 minutes after that sample is obtained. This paper describes the system and its use and presents comparative results for various process streams.

Jan 1, 1993

By V. Svalbonas, M. Fresko

The present versions of the Welding Codes, such as BS7608, have long been known to be compatible with hand computations of membrane and bending stress, rather than detailed finite element solutions. However, in the last five years, in the mining industry, this incompatibility has been largely ignored, and the code interpretations have been pushed into the realms of ground welds, residual stresses, and even flaw growth. Such techniques have to be recognized as extrapolations not necessarily sanctioned by the original code documents. The safety of such extrapolations, as they are related to grinding mill fatigue design, is investigated herein.

Jan 1, 2002

By A. J. Kwitowski

Remote control is usually associated with deep mine, continuous mining machines. This is because thin-seam operation precludes an onboard operator&apos;s compartment or the mine has approval to conduct extended cut mining. Using a tethered or radio-linked control box, the remote operator is typically situated 3 to 15 m (10 to 50 ft) from the working face. The operator receives direct operational cues through senses like vision, hearing and feel. Remote control is sometimes touted as a safety feature. However, this is not always true, as operators are not provided protection from roof and rib falls or being crushed between the machine and a rib. Remote control operators are also left exposed to dust and noise. Teleoperation described here is the computer-based, distant control of mining machinery from a protected operator compartment located out of the line-of-sight from the operational site. Video, sound and other sensory information are gathered through sensors and electronically transmitted to and displayed at the operator&apos;s location. The teleoperator responds to the information and makes decisions that are initiated by control devices (usually switches). These control commands are then electronically transmitted to the re¬mote machinery and the appropriate machine function(s) are carried out. Teleoperation increases the safety of mining machine operators as it removes them from the immediate vicinity of hazards. The US Bureau of Mines&apos; involvement with teleoperation dates back to 1979. Following feasibility studies, a highwall milling system (HMS) was developed and tested. A deep, thin-seam, room-and-pillar system (TSRPS) has been designed and is currently being surface tested.

Jan 1, 1992

By Brent Chamberlain

MARY KORPI: As has been typical today, our next speaker is filling in for one of his co-workers. Scott Lawson will be discussing "The Role of the Supervisor in Mining Operations" written by Brent Chamberlain of Independence Mining Corporation. Scott has more than 25 years in human resources management in the mining industry. He has worked in surface and underground mining environments in both precious and base metal mines. A graduate of Ohio University, Scott is currently manager of human resources at the Independence Mining Company&apos;s Cripple Creek and Victor Gold Mining operation located in Victor, Colorado. The only direction that I received from Scott was that he has to leave by 11:45 a.m. as he has a tee-off time with his boss at 1:00 p.m. Thank you to Scott for filling in today.

Jan 1, 1998

By T. A. Toney

With new lightweight designs, spirals have become standard equipment in coal preparation plants worldwide. To their credit, spirals typically show very low coal losses to the refuse stream under most operating conditions. However, spirals do tend to separate at cut points in excess of 1.80 S.G. Attempts to obtain lower cut points have typically resulted in coal losses to middlings. Middlings retreatment with secondary spirals is therefore becoming common place. Other forms of retreatment with water-only cyclones, hydrosizers, and recirculation have been attempted with some success. This paper reports on a novel (Patent Applied For) approach to retreating spiral middlings m a heavy-media-cyclone circuit.

Jan 1, 1998

By L. D. Ellison

The ventilation of a bituminous coal mine by means t of a Forced and, or, Exhaust system of ventilation is certainly not new to the mining industry, however, we know from experience that the ventilation of every coal mine presents a variety of problems which are in some instances approached by different methods or means, As in every such problem, there is some difference of opinion as to the advantages and disadvantages of s Exhaust versus Forced ventilation, particularly with regard to safe and effective ventilation of an active pillar area in a gaseous coal mine. We at Island Creek, certainly concede that it is possible to safely ventilate a coal mine by means of Forced ventilation, However, following many years experience in operating a coal mine in an extremely gaseous coal seam, we prefer using an Exhaust system, that is, to reduce the inside mine pressure to a minus atmospheric pressure by means of a mechanically operated fan. This method assures that the return air moving through established airways toward the fan will continue to move in that same direction for a limited time should the fan stop for any reason, also assuring that in the event of a large area fall, the air from the abandoned workings will move directly to the suction side or to the return airways.

Jan 1, 1960

By J. A. Botín

In modern mining, the core of mine planning and design is the block model, a simplified representation wherein the ore deposit is divided in a number of virtual rock cubes, each characterized by technical and economics parameters. Mining engineers use this model to design the mine and develop production schedules. Traditionally, sustainability issues are not considered in the mine design, planning and engineering processes but rather are incorporated in the later stages of the feasibility evaluation as necessary expenditures and operating costs. This paper describes the results of a research project aiming to develop a methodology to incorporate sustainability parameters directly into the block model, so that they become an integral part of the design, planning and scheduling processes. It is considered that the incorporation of sustainable parameters into the block model would yield a more responsible mine design and improve mining projects sustainability performance

Feb 27, 2013

By A. S. Polubinsky, V. P. Chernyak

A further development of the theory of heat- and mass transfer in the system “strata - mine opening" is necessary for an improvement of the existing technique of heat calculation of mines and other underground constructions. A generalized boundary problem of heat- and mass conduction in strata around an opening as a theoretical ground for that purpose and several particular situations, important from the point of view of an opening and surrounding strata heat state analysis, as well as results of numerical experiments executed for such analysis are presented.

Jan 1, 1997