Search Documents

By J. W. Markham, M. Atiemo, K. Yoshida

INTRODUCTION In open-pit mining of high grade ores, operators of mining equipment in a pressurized cab are protected from inhaling radioactive aerosols by the use of filtered air through a pre-impactor and a HEPA (high efficiency particulate air) filter. At present, a limited amount of scientific information is available on the worker exposure to airborne alpha emitters in the mining of high-grade ores. (Miller, 1977, Nielson, et al, 1979). Factors affecting the worker exposure to alpha radiation are: the grade of uranium containing ores, the environmental conditions inside the mine pit, the protection factor of the cab filter system, the workers' attitude towards the hazards of radioactivity and the adopted contamination control in the cabs. Four series of field samplings were conducted during the fall of 1980 and the summer of 1981 at a mining site in northern Saskatchewan to investigate the extent of protection an equipment operator has against cab internal exposure to airborne alpha emitters with short and long half-life radionuclides. The variation in the breathing zone concentrationnof aerosols as a result of resuspension is discussed, however no attempt was made to isolate and investigate the factors and the associated parameters of the aerosol resuspension phenomenon. AEROSOL RESUSPENSION IN A CAB Mechanisms of Resuspension [Sources]: The presence of radioactive aerosols inside a cab and in the breathing zone of an operator may be due to initial concentration inside [(CO)], concentration in the filtered (HEPA) air (CC, at the flow rate [QC]), the concentration of the aerosol through resuspension ([CR]), the aerosol concentration in the air outside the cab ([CE]) and the concentration of the aerosol in the leaking air [(CL)], at the flow rate of [(QL)]. [Volumetric Equilibrium]: Assuming a uniform concentration of the aerosol in the cab, the aerosol concentration in the breathing zone[ (CBZ)] may be expressed as, [CBZ+CO+CC+CR-CL] If [QC] remains greater than [QL], there is pressurization in the cab. There is particle loss as a result of the leaking air from the tight cab, however the condition of adequate pressurization ensures that [CL ~ CC]. Also for dust particles filtered through HEPA [CC – 0] thus [CBZ + CO + CR] For the radioactive gases, [CBZ - CO + CC] Over long periods,[ CBZ – CE] but if [CBZ] exceeds the value of CE then the aerosol build-up in the cab has, occurred. [Resuspension]: Turbulent bursts are generated within the core region of a cab confinement, such that the down sweeps and the up sweeps of the air bursts cause resuspension of dust from the surfaces. Particles initiate resuspension by four major modes: namely, sliding, rocking, rolling, bouncing or sudden ejection or by combinations of these. Nevertheless the adhesion force between the particles and the surface must be overcome by ejection forces before ejection takes place (Kline et al, 1967, Corino and Bradkey 1969, Kim et al 1971). The phenomenon of particle resuspension from a surface may be expressed in a generalized form as: CR =f (Uz . R . D . H) where CR = Rate of particle resuspension UZ = Surface shear velocity R = Surface roughness parameter D = Aerodynamic diameter of particle H = Frequency of surface airburst A detailed discussion of the individual parameters was attempted for the case of farm tractor cabs by Atiemo (1981), such a treatment is out of the scope of this study. Only the effects of the properties of surface roughness will be discussed. Effect of Surface Properties The roughness of the surface from which dust particles are ejected plays a significant role in the deposition and resuspension of the dust. The roughness or the amount of protrusions greatly influence the intensity of air turbulence in the immediate vicinity of the surface (Schmel 1976). For most roughened surfaces therefore, larger particles may be dislodged in greater quantities than smaller particles. The deposition and the resuspension of dust particles from different surface materials of glass, cloth, metal and rubber have been studied in a wind tunnel (Atiemo, 1981). Field Conditions Mining equipments used are: a backhoe, a bulldozer with ripper attachment and two dumptrucks for high-grade ore operations; a payloader and two dumptrucks for waste handling; and a jumbo drill which drills dynamite holes for ore blasting. All this

Jan 1, 1981

By D. R. Gagnon

Mining companies are continually looking for product-ivity and efficiency improvements with their equipment to reduce operating costs. This paper will review the results of a productivity analysis conducted at the Luscar Ltd. Boundary Dam and Bienfait mines near Estevan, Saskatchewan using a Computer-Aided Earthmoving System (CAES) installed on a track-type dozer. The CAES TTT system is a Global Positioning System that provides the operator with constant survey guidance. The study includes a productivity comparison between two similar test sites, one with the aid of the CAES system and the other, without. The CAES TTT system shows a productivity improvement of between 20 and 35% in the reclamation slope leveling application. Even with the CAES TTT system deactivated, some of the advanced features of the system were used to: retain terrain data for volume calculations; track the equipment position; and, accurately record and separate idle time from working time.

Jan 1, 2002

By B. F. Buie

In South Carolina and Georgia an area about 20 miles wide situated near the inner margin of the Coastal Plain and extending from the vicinity of Columbia, S.C. southwestward about 180 miles to the vicinity of Macon, Georgia is the principal kaolin-producing area of the world. It is especially important as the world's major source of clay used for paper coating. Essentially all of the land known or likely to be productive of quality kaolin in this area is now owned or controlled by producing companies. The least-fully developed portion is that in the vicinity of Wrens, Georgia which has been explored and developed since 1961. For the two decades following the end of world war II, demand for kaolin increased at approximately twice the rate for other industrial minerals. From 1945 to 1965 production increased four-fold. Since 1965 the rate of increase has been less, but the outlook now is that production and demand will double at least once again before the year 2000. A substantial part of this increased demand has come, and will continue to come, from industrial development, especially in the paper industry, outside the United States. The general effect, in addition to a continuing increase in production in the U.S., will be to cause: 1. Intensive research for development of more effective and more economical methods of beneficiation; 2. Concerted research effort to find an economical way of modifying high-viscosity kaolin so that it can be used for paper coating; 3. More active exploration in the U.S. and overseas, especially for deposits to supply the foreign markets; 4. More intensive study of the geological factors responsible for the accumulation of commercial deposits of kaolin; 5. Some modest rise in price, relative to the cost of other industrial minerals. The effect on kaolin producing region of Georgia and South Carolina will be to cause: 1. Working of progressively lower-grade deposits; 2. An increase in the acceptable thickness of overburden; 3. Mining of deposits farther down-dip, the use of which is now inhibited by large volumes of groundwater; 4. Increased threat of invasion of the kaolin in industry's market by substitute materials; 5. A substantial increase in concern over environmental factors; 6. More attention to be paid to the large opportunity offered for mining of silica sand and other co-products.

Jan 1, 1972

By B. A. Massey

Sooner or later, we'll encounter a subordinate, peer, or boss that will test our management skills to the limit. The chances are good that our formal educations have not fully prepared us to effectively handle the situation, and through trial-by-fire, we have learned that the management of people is often as much an art as it is a science. Assertiveness - as opposed to agressiveness - is basically positive persuation. Assertive management techniques can help combine the art and science of managment to sell ideas, accomplish goals, direct the workforce, and generally promote the corporate - as well as our own - objectives

Jan 1, 1986

By James J. Fallon

Last summer Larry Miller of Roberts & Schaefer told me that his AIME committee would like me to present some thoughts on the marketing of industrial mineral fillers and pigments to this illustrious group in Las Vegas. Shortly after, Brian Coupe of "Industrial Minerals" (the magazine) notified me that I would be presenting a paper to the Fourth International Industrial Minerals Congress in Atlanta this June. It seems to me now it might have been more appropriate to reverse the papers. Las Vegas, a town based on risk, might want to hear what we have to say in Atlanta. The subject for June is "Risk Philosophies of U. S. Industrial Minerals Companies". However, upon reflection, marketing of industrial minerals reflects risk philosophies to a considerable extent, so we'll cut the deck and deal on the subject of marketing.

Jan 1, 1980

By L. W. Ashton

Geochemical exploration guidelines were developed from a study of 460 rock chip samples collected at nine disseminated gold deposits in Nevada. Obtaining high grade Au samples is difficult because gold content is extremely variable, even over 8 m (25 ft) distances. For reconnaissance sampling, pathfinder elements are reliable indicators with threshold values of 100 ppm As, 1 ppm Hg, and 50 ppm Sb. Arsenic is the most reliable of the three elements, being significantly enriched in all deposits. If the pathfinder threshold levels are reached with low Au content, more samples should be collected. Successful disseminated gold exploration requires large numbers of samples.

Jan 1, 1990

By P. J. Rua

The Piedras Verdes copper mine is a new run-of-mine (ROM), heap leach, solvent-extraction/electrowinning (SX-EW) operation located 21 km (13 miles) north-northwest of the town of Alamos in the state of Sonora, Mexico. The Piedras Verdes copper mine is wholly owned by Frontera Copper Corp. (FCC), a Canadian corporation, through its 100 percent beneficial interest in Cobre del Mayo S.A. de C.V. (CDM), a Mexican registered company. The January 2008, minable reserves were estimated to be 193.6 Mt (213 million st) at a grade of 0.36 percent copper. The overall recovery of total copper was estimated to be 61.9 percent. The property has an additional 17-year life and is designed to produce 31.7 kt/a (70 million lbs/year) of cathode copper. Construction commenced in early October 2005. The first copper cathode was produced 12 months later at a total capital cost of $100 million. Elevations at the site range from 150 to 300 m (490 to 985 ft) above sea level. The area has excellent infra-structure in the form of towns, power, water, roads, rail, airfield and access to the deepwater port of Guaymas (Fig. 1). The surrounding area is also famous for its numerous polymetallic (lead, zinc, copper, silver and gold) epithermal veins. Some of these were mined for more than 200 years and provided the wealth on which the town of Alamos was built. The original village of Piedras Verdes was located in the area of the proposed openpit mine and, consequently, it was necessary to construct a new townsite 6 km (3.7 miles) to the south before project development could commence. The new town site (Fig. 2), complete with power and water supplies, roads, sewer system, schools, clinic and recreational facilities, was completed and occupied by 49 families in September 2005. CDM received its remaining permits from the Mexican environmental authorities on Sept. 20, 2005. This enabled the company to proceed with full-scale development. CDM owns or controls 27 mining concessions covering the resource. Surface rights to the Piedras Verdes project were controlled by four Ejidos (communal agrarian and/or ranching societies) and five individual landowners. CDM has acquired all surface rights necessary for its mining operations and associated facilities either through outright purchase or long term lease agreements.

Jan 1, 2008

By W. J. McDonough

Rapid growth and acceptance of engineered materials have changed the way we live. We have come to expect improved performance at less cost. At the same time, our awareness of societal and environmental issues created by these materials during and after their lifetime has been heightened. As a result, material lifecycle analysis is receiving considerable attention. Material lifecycle analysis evaluates the cost/effective tradeoffs at each stage of a material's life: feedstock, fabrication, performance, recycle, and disposal. The U.S. Bureau of Mines investigates a material's lifecycle using technical cost models augmented with decision and impact analyses. Results of these studies are useful in gaining a better understanding of current material selections and illustrating the multifaceted issues associated with engineered materials in today's society.

Jan 1, 1992

By D. W. Carson, R. J. Trembley

Thoron daughter WL&apos;s measured by alpha-spectroscopy and the Kusnetz method are about one-half those of radon daughter WL&apos;s in a uranium mine in Canada.1 A diffusion model can account for the relative concentrations.l Since the Kusnetz technique is most widely used for measuring radon daughter WL&apos;s in uranium mines, a general procedure is derived to extend this method to measurement of WL&apos;s of radon and thoron daughters in air containing their mixtures. Coté P. and Townsend M.G., 1981. A procedure is also suggested for counting radon and thoron daughters by 3-channel [a]-spectroscopy. Errors in WL(Rn) are calculated for standard radon daughter counting procedures when a-decay of both thoron and radon daughters is attributed to radon daughters alone. Providing overall counting times are short, [<]30 min, these errors are generally small. The precision of ß -counting methods is also investigated. A portable 3-channel alpha spectrometer for measurement of radon and thoron daughters in uranium mines or homes is described, Carson D.W., 1979. The computer programs for analyzing the data to give, depending on the mode employed, some or all of the concentrations RaA, RaB, RaC, ThB, ThC and WL of radon and thoron daughters by alpha spectrometric, modified Kusnetz, Rolle and Tsivolglov methods are presented.(l) A commercial apparatus, based on the above prototype, incorporating a microprocessor and built under contract to EMR is now available.(2) A number of personal radiation dosimeters for miners are now being tested in mines. One of these is the CEA dosimeter which uses the track-etch film method, Duport P., Chapuis A.M. and Pradel J., 1979. An apparatus for rapid reading of track-etch films by the spark technique has been described previously, Cross W.G. and Thomasino L., 1970 and Huang V.F., 1975. We have developed such an apparatus for rapid semi-automatic reading of films exposed to radiation from mixtures of radon and thoron daughters in CEA dosimeters. The films used, Kodak LR 115 Type II Strippable, may be stripped rapidly and easily, for counting after irradiation and developing, by use of a special punch and suction technique. The method promises to provide an inexpensive and rapid technique for reading large quantities of personal dosimeter films. However, the present CEA dosimeter has faults in design, leading to a contamination problem. Those films that show contamination cannot be read by automatic means. A commercial apparatus based on the above prototype spark counter and built under contract to EMR is now available.3 1. These computer programs are available on request. 2. Pylon Instruments, Ottawa 3. Bondar Clegg, Co. Ltd., Ottawa. REFERENCES Carson, D.W., 1979, "Canalph-3, a Portable Three-Channel Alpha-Spectrometer for Measuring the Daughter Products of Radon and Thoron", CANMET Division Report MRP/MSL 79-108 (TR). Coté, P. and Townsend, M.G., 1981, "Mixtures of Radon and Thoron Daughters in Underground Atmospheres", Health Physics, Vol. 40, pp 5-16. Cross, W.G. and Thomasino, L., 1970, "Rapid Reading Technique for Nuclear Particles Damage Tracks in Thin Foils", Radiation Effects, Vol. 15, pp 85-89. Duport, P., Chapuis, A.M. and Pradel, J., 1979, "Appareil Individuel pour lu Dosimetrie des Descendants du Radon", Advances in Radiation Protection Monitoring, IAEA Vienna, pp 435-443. Huang, Y.F., 1975, "Determination of Uranium in Minerals using Fission Tracks", M. Sc. Thesis, University of Toronto, 48 pp.

Jan 1, 1981

By Jacob L. Brinkman, Catherine E. Johnson

Unmanned aerial vehicles (UAVs) are being explored by researchers to measure concentrations of gas emissions in situations where such measurements are otherwise extremely difficult to obtain, such as NO and NO2 (NOx) emissions from surface mine blasting. Recently, countries have imposed or are planning to impose surface blasting gas pollution regulations, which creates a need for an improved understanding of UAV-based gas measuring systems. The experiments detailed in this paper were performed to determine if airflow generated by the rotors, also known as downwash, unnaturally alters concentration measurements. Downwash turbulence could create locations of varying pressure, which could affect concentration. A UAV fitted with gas sensors was attached to a stand in a controlled environment containing a mixture of NOx. The gas sensor measuring points were placed at various distances on and from the UAV body to evaluate downwash effects on gas concentration. Results show that the presence of downwash turbulence causes no statistically significant changes to concentration measurements at any distance or direction from the UAV. Based on these results, it is possible to use a UAV-mounted gas monitor to measure concentrations without concern for downwash interference, provided the UAV and measuring point are entirely contained within the gas cloud.

May 20, 2021

By Michael J. Robison, Wojciech F. Klecan, Robert L. Horner

Since 1928, nearly 64 km (40 mi) of tunnel have been excavated within the relatively soft Cooper Group, more commonly known as the “Cooper Marl,” for water supply and transporting wastewater in the Charleston area. The majority of these tunnels are unlined and still in operation, while others collapsed shortly after excavating. Tunnel behavior and support requirements vary considerably in this material due to differences in geotechnical properties. The 4.8 km (3 mi) long, 2.4 m (8 ft) diameter Bushy Park Water Tunnel, completed in 1997 for Charleston’s Commissioners of Public Works(CPW), required no ground support. By comparison, the 1.6 km (1 mi) long, 2.4 m (8 ft)diameter Harbor Wastewater Replacement Tunnel now under construction needs continuous support close to the advancing face, despite being located in the same geological formation. Case histories and general guidelines for designing tunnels in the Cooper Marl are presented.

Jan 1, 2001

By J. A. Hartlage

Four years ago, Ashland Chemical Company introduced a new copper solvent extraction reagent for hydrometallurgical utilization. The reagent, an alkylated 8-hydroxyquinoline, is called Kelex 100 ®(1). Since the time of introduction, the reagent has been investigated by several workers for its solvent extraction utility in the separation and purification of transition metals (2-7). In the following text, those factors which are essential to the optimum performance of Kelex 100 on concentrated copper solutions will be discussed. To date, the reagent has been found useful in active concentrations of from 1 to 20% Kelex 100. In order to achieve the best performance for Kelex 100, it has been found that a phase modifier is essential. Various alcohols and phenols have been evaluated in order to improve phase performance and stripping characteristics of the solvent system. Modifiers and diluents are especially important when solvent activities between 3 and 20% Kelex 100 are employed. A 15% Kelex 100 solvent, for example, containing 15% nonyl phenol in Escaid 100 (Exxon) can be utilized to remove greater than 33 grams per liter of copper from an aqueous feed without interstage neutralization, and in the same process scheme the reagent can be stripped to less than 1 gram per liter barren organic producing a pregnant electrolyte containing greater than 40 grams per liter copper and less than 120 grams per liter sulphuric acid. The unusually efficient stripping of Kelex is accomplished by protenation of the extractive molecule during the stripping process.

Jan 1, 1974

By D. A. Bird

Geochemical models using published thermo-dynamic data and laboratory derived kinetic rate laws allow prediction of post-closure pit lake geochemistry at open pit mining sites. A combination of "forward" and "inverse" modeling techniques can predict the pit lake geochemical evolution from initial infilling to eventual steady state attained decades or centuries after closure. Computer codes have been developed to model chemical reactions such as pyrite dissolution, describe the ground-water flow regime, and provide rock-water ratios. The incorporation of site specific information, such as ultimate pit dimensions, geologic and hydrologic data, acid generating potential (AGP) vs. acid neutralizing potential (ANP), and laboratory derived kinetic rates, allows application of the model to open pit mines at any stage of development.

Jan 1, 1994

By Kefton H. Teague

Olivine was first described and named by Warner in 1790. It is an olive green to greenish gray colored magnesium-iron silicate containing a mixture, in solid solution, of fosterite (Mg2SiO4) and fayalite (Fe2SiO4). Ratios between fosterite and fayalite in olivine are somewhat variable, but in general olivine contains at least 85% fosterite. Specific gravity is variable also, depending on the ratios of fosterite to fayalite. As a rule it is in the 3.2 - 3.4 range. All commercial olivine is obtained from the rock dunite, the most basic member of the peridotite group. Dunites, in addition to being composed primarily of olivine, generally contain assessory pyroxenes and spinels (chromite and magnetite). Dunites&apos;, when altered by hydrothermal solutions or metamorphism, often contain alteration minerals such as talc, serpentine, chlorite, vermiculite and amphiboles. In the 1930&apos;s and 40&apos;s considerable research was conducted on olivine for use as a refractory, plant food raw material, magnesium source for metal, and a source for magnesium chemicals. This research met with only limited success.

Jan 1, 1977

By H. Y. Sohn

Considering the two most important issues the ironmaking industry faces today, i.e., energy consumption and greenhouse gas emissions, it would be advantageous to utilize the concentrate-size raw materials directly without pelletizing or sintering, especially without the use of coke. This plenary lecture describes two such processes developed at the University of Utah. One is the Flash Ironmaking Technology (FIT) and the other is a moving-bed process for continuous ironmaking with gaseous reduction of iron ore concentrate (MBIT). These technologies are designed to produce iron directly from iron concentrate without requiring pelletization/sintering and cokemaking in two significantly different temperature ranges. They take advantage of the high reactivity of the concentrate particles and will considerably reduce energy consumption and carbon dioxide emissions compared with the current processes. The process of the development from the conception of the idea, to kinetic feasibility establishment, to laboratory flash furnace, and finally to the operation of a prototype facility for the development of the FIT is discussed. The development of the MBIT also started with the formulation of the process concept, followed by kinetics feasibility establishment, and the design of a potential industrial reactor. The results of economic analyses on the FIT are briefly described.

May 12, 2023

By Thomas C. Anderson, Terry Weiss

The Mount Gunnison No. 1 Mine of the West Elk Coal Company (wholly owned subsidiary of ARCO Coal) had secured contracts to provide low sulfur, high Btu steam coal to various utility companies. This called for the development of the B-Seam at the Mount Gunnison Mine located some 400 feet below the operating F-Seam workings being mined with conventional room and pillar techniques. The B-Seam, to meet production goals, will be mined by a new 600-foot longwall machine making a 13-foot high cut. American Mine Services was awarded a competitively bid contract to drive two 2000-foot, 13-foot by 16-foot slopes at -15 percent, sink a 16-foot diameter ventilation shaft 400 feet between the F- and B-Seams, install a 60-inch conveyor in one of the slopes, remove 7000 feet of existing conveyor and rehabilitate 7000 feet in two entries to accommodate the placement of the longwall machinery. The slope portals were located 7000 feet in by the surface portal. Unique to the project was the placement of work shops and other infrastructure 7000 feet underground with an entry height of 6 feet. The $7 million contract was completed in less than one year using a mix of permissible (Schedule 31) and standard (Schedule 24) LHD equipment, all pneumatic jumbos and shaft sinking gear.

Jan 1, 1993

By S. D. Rosenthal

"This paper will share my ‘shift in career direction’ journey from corporate mine engineer, with 31 years of mining various commodities with a wide range of responsibilities in a variety of countries, to the world of academia. There are times in one’s career that a change is required, albeit perhaps not as drastic of a change as moving to teaching. This paper will share how the transition arose, the decision to make the change, the challenges of the first year in academia, and the journey within academia going into the second year. INTRODUCTION As a graduate of the Montana College of Mineral Science and Technology (Montana Tech) with a B.S. Mining Engineering degree in May of 1982, my first job with Utah International in the Farmington area took me back to my home state of New Mexico. Some of you will remember that the early 1980’s was not a period of prolific opportunities for mining engineers; given low commodity prices, especially for copper (for example, Anaconda Company had been taken over by Arco and was in the midst of closing down its Butte operations). Coal was good and the learning opportunities abounded with Utah (which became BHP and then BHP Billiton). Gold was taking off in the mid to late 1980’s thanks to use of cyanide and heap leaching technology improvements, coupled with deregulation of the gold price, so I ventured off to work in the gold industry with a (then) junior Canadian company called Barrick at a new acquisition of theirs known as Goldstrike. That same gold surge was causing a shortage of iron ore mining engineers in Australia so after a few years in Nevada, I uprooted the family and left for a little town in the Pilbara of West Australia, known as Newman, to work in the iron ore industry with BHP Iron Ore. An initial short overseas posting turned into six plus years before transferring to BHP’s Indonesian steam coal mines in Kalimantan on the island of Borneo. BHP was going through a rough period following some ill-fated projects (Magma copper purchase, Beanup and HBI) and was reviewing assets and staffing so internal opportunities became scarce. Employees were encouraged to ‘leave the company and find work elsewhere.’ So, off I go to Argentina to try copper mining in the Andes with Minera Alumbrera. This short stint in South America was followed by a move to another mining town, Morenci, Arizona, and a posting with Phelps Dodge (now Freeport McMoran). After 12+ years without living close to snow we moved to the Denver area in a new position with Newmont Mining Corporation. Along the way I became a Professional Engineer (Nevada) and completed a Masters in Project Engineering and Management. After 11 years with Newmont, I moved to Butte, Montana where I accepted a position as Assistant Professor of Mining Engineering."

Jan 1, 2015

By R. K. Steinhorst

Multivariate cluster analysis, MANOVA, canonical analysis, and discriminant analysis of hydrochemistry data were used to investigate the directions of ground water movement in basalts in the vicinity of the Hanford Reservation, Washington. The statistical analyses indicate that the hydrochemistry of the ground waters in these basalt formations is distinctly different on each side of the Columbia River. This suggests that the river is a ground water divide or that the river is roughly coincident with a hydrogeologic barrier boundary. The statistical procedures used in this study constitute a quantitative means for differentiating ground waters according to hydrochemistry.

Jan 1, 1990

By F. Alsobrook

Industrial minerals are receiving increased attention by metals, coal and other companies seeking to diversify and stabilize earnings. Each industrial mineral has a unique set (and sub-sets) of business dynamics, however, and the diversity can present a bewildering maze to the corporate planner. Shrugging off this complexity and relying on serendipity for entry opportunities often results in unsuitable acquisitions. An effective alternative used in exploration can also be applied to strategic planning. By providing focus and direction, this flexible methodology can prevent wasting corporate resources on random pursuits and result in a quicker, more satisfactory achievement of diversification goals.

Jan 1, 1990

By R. E. Ray

As coal reserves at shallow depths continue to be exhausted, a number of US coal companies are developing seams previously considered too deep to mine economically. Because of increased cover load, mines operating in deeper seams face unique ground control problems. In addition, the volume of methane gas in coal beds increases with depth, and ventilation requirements are much more stringent for deep mines than for shallower mines. When the longwall mining method is wed at great depths, ventilation, ground control, and operational considerations all influence the design of longwall panels. This paper examines these influences, particularly ventilation and operational considerations, on the feasibility of two-, three-, and four-entry longwall development panels in Jim Walter Resources&apos; four deep mines.

Jan 1, 1988