Search Documents

By W. E. Hale

The Institute of Applied Geology (I.A.G.), a joint project sponsored by the University of the Philippines, the Philippine Bureau of Mines and the United Nations Development Programme (Special Fund) undertook during 1965-66 a number of field projects in Northern Luzon Island (Fig. 1). These field operations were of a two-fold nature: during approximately six weeks an orientation survey, involving, geology, geophysical surveying, and geochemical prospecting, was conducted over a partly developed, disseminated copper deposit at Sto. Nino (Fig. 1). The Sto. Nino study demonstrated (Hale and Govett, 19677 Govett and Hale, 1967) the feasibility of geochemical prospecting relative to other exploration methods for the location and delineation of disseminated copper occurrences, the major source of metal in the expanding mineral industry of the Philippines. A vein occurrence at Suyoc (Fig. 1) was similarly subjected to

Jan 1, 1968

By James E. Lawver

During the past century, the Florida Phosphate Industry has established an enviable record of innovative technology in nearly all aspects of mining and beneficiation. A notable exception is the lack of technology to improve the present practice of storing waste clay in earthen dams. The rule which has been adopted by the Department of Natural Resources states, "Since storage of clay wastes for long periods of time interferes with expeditious reclamation and since above grade storage of clays takes otherwise useful land out of production and raises potential health and safety problems, below grade storage and rapid reclamation techniques are encouraged." The two waste products from the beneficiation plant are clay slimes (-0.1 mm in size) and sand tailings. The sand tailings do not present a problem since the tailings rapidly dewater to a dry weight of about 100 pounds/ft3 and make good land fill. By contrast, disposal of waste clay slimes is a formidable task. The basic problem is simply that the waste clay not only dewaters very slowly, but also that the ultimate solids content is very low and in most cases the volume of the clay greatly exceeds the available volume of below ground storage of the mined land.

Jan 1, 1984

By B. K. Cantrell

A miner working in an underground coal mine with diesel equipment is exposed to a wide array of pollutants from the diesel exhaust. These include CO, CO2, NO, NO2, SO2, diesel-exhaust aerosol, and a variety of hydrocarbon compounds. A quantitative definition of the health risk resulting from these exposures remains elusive, but during the past several years, progress has been made in defining the problem. Results from epidemiological studies by Garshick, et al. (1988); animal inhalation studies by Mauderly, et al. (1986); Iwai, et al. (1986); and Brightwell, et al. (1986); and in vitro studies by Lewtas, et al. (1986), have provided sufficient data for the National Institute of Occupational Safety and Health (NIOSH) to recommend that "whole diesel exhaust be regarded as a 'potential occupational carcinogen,' as defined in the Cancer Policy of the Occupational Safety and Health Administration," NIOSH (1988). NIOSH further stated that "though the excess risk of cancer in diesel-exhaust-exposed workers has not been quantitatively estimated, it is logical to assume that reduction in exposure to diesel exhaust in the workplace would reduce the excess risk."

Jan 1, 1990

By M. De Ladurantaye-Noël, M. Laliberte

Selenium is widely present in the environment at usually low concentration. It is mostly present in the environment at higher oxidation states, i.e., as selenites and selenates (+4 and +6 oxidation states respectively). It is rarely present as selenides (-2 oxidation state) and almost never found as the element (0 oxidation state). Selenites and selenates are generally soluble in water, as such they cannot easily be removed from water by precipitation. Selenites can form insoluble surface complexes with metal oxides such as ferric hydrous oxide and manganese hydroxide, and can therefore be removed that way. However, it is not so common to find selenites in natural environments as it will quickly oxidize to selenate in aerobic conditions. Elemental selenium can also be produced from selenites or selenates by using a reduction process; the end product is a colloid that can be destabilized to be removed from water using the right chemistry. Because of their toxicity, selenides need to be handled with care, and if present, it can form insoluble metal salts or, at low pH, be emitted as H2Se, a noxious and highly toxic gas. The most favorable selenium forms for its removal are therefore selenite and elemental selenium. Organo-selenium species play a crucial part in understanding selenium toxicity. There are a great number of these species. Basically, any organic species that contains sulfur has an equivalent that contains selenium. Of particular interest is the substitution of sulfur by selenium in the two sulfur-bearing amino acids, cysteine and methionine, resulting in selenocysteine and selenomethionine. Methylseleninic acid (CH3SeO2H) is another organo-selenium specie which has been detected in water treated by biological processes and which is biologically active.

Feb 1, 2023

By D. Tahija

"Hecla's Greens Creek silver-gold-lead-zinc mill began using carbon dioxide rather than sulphuric acid to control pH in April, 2015. High pH levels in the grinding and lead flotation circuits are caused by the presence of re-mined cemented paste backfill in mill feed and need to be lowered to achieve good flotation response. Carbon dioxide has proven to be quite effective at controlling pH in the lead circuit with greatly improved pH target attainment. The allowable amount of carbon dioxide used is not limited by effects on lead-zinc selectivity and by poor froth characteristics, as was the case with sulphuric acid. Startup and implementation went smoothly, with few operational issues needing to be resolved. Early results from implementation of the system and its effects on mill performance will be presented. INTRODUCTION Hecla Greens Creek is a silver-gold-lead-zinc mine producing flotation lead and zinc concentrates, as well as a gravity gold concentrate. Besides their base metal contents, both the lead and zinc concentrates carry precious metals. The circuit is largely conventional, with SAG and ball mill grinding being followed by graphite removal preflotation, then conventional lead flotation and conventional zinc flotation. Both rougher concentrates are treated in regrind steps, followed by cleaner flotation. The cleaners tails are treated in an unorthodox bulk circuit to produce a low-grade zinc-lead concentrate marketed to Imperial Process smelters (1). BACKGROUND Backfill and Flotation pH The Greens Creek mine is an underground operation in which mined areas, after ore extraction, are backfilled, using rammed paste or pumped slurry. The backfill consists of mill tailings to which approximately five percent Portland or similar cement is added to enhance its compressive strength. Later mining near backfilled areas inevitably results in a considerable amount of old backfill being mixed with new ore before being shipped to the mill. Depending on orebody geometry, mining methods etc., the amount of backfill in mill feed is often 20% to 25% and sometimes even higher. Commercial cement, and consequently backfill prepared using it, contains excess lime. Because of this, backfill in mill feed is indistinguishable from the addition of a large amount of lime, so mill natural pHs often range above 10 or even 11. Similar situations have been recognized for many years at mines throughout the world (2)."

Jan 1, 2016

By Natasa Mitevska, Predrag Djordjevic, Zivan Zivkovic

This paper presents the results of an experimental investigation into the distribution of copper in the slag of an industrial reverberatory furnace sulfide concentrates smelting process in the copper smelter RTB Bor (Serbia). The influence of copper content in the matte, the temperature and the height of the slag on the content of copper in the slag was determined as Cuoxide, Cusulfide and Cutotal and was based on possible mechanisms for the loss of copper in a silicate slag from the smelting of sulfide copper concentrates. The greatest quantity of copper in the silicate slag was found in the form of matte particles, which were captured in the slag as a result of the “flotation” of SO2 gas which was formed by magnetite reduction with FeS at the slag–matte interphase boundary.

The prediction and control of ground deformations due to underground mining are important considerations in the permitting, planning, and monitoring of coal mining operations. The prediction of mining-induced ground movements using the influence function method is a mature technology and is widely used in many coal basins around the world. Such movements mainly include subsidence, horizontal displacement, and horizontal and/or ground strain. Predictions can be accomplished using regional subsidence parameters and site-specific data.

Jan 7, 2020

By William J. Miles

The markets and applications of Wyoming bentonite deposits are primarily determined by the functional properties of a bentonite ore which results from the unique mineralogy and chemistry of each deposit. Commercial bentonite products contain sodium montmorillonite as the major mineral component, with minor concentrations of accessory minerals such as quartz, opal (silica hydrate), mica, feldspar, gypsum and zeolites. The chemical composition of the sodium montmorillonite influences the functional properties of the bentonite in significant ways. The type and concentration of various accessory minerals also influence the acceptability of the bentonite in each market.

Jan 1, 1995

By G. Ferrara, P. Bozzato, B. Chinè

To obtain a reliable comparison between conical and cylindrical separatory vessels used in dynamic dense-medium separation systems, the following two studies were made: a study of the swirling flow in conical and cylindrical vessels using laser-Doppler velocimetry (LDV) and a study of the behavior of suspensions of magnetite and ferrosilicon in water in both separators. It was found that the tangential velocity profiles differ in conical and cylindrical vessels. In a conical cyclone, free vortex conditions affect the largest part of the vessel, while in a cylindrical vessel, the motion approaches that of a forced vortex, i.e., that of a centrifuge. It was also found that the conical vessel manifests higher centrifigal acceleration and very strong densifying (the density differential) and, hence, the density gradient inside the vessel is large. It was found that the cylindrical vessel manifests lower centrifugal acceleration and low densifying, i.e., low-density differentials, and hence, the density gradient inside the vessel is small. Also, due to greater densifying, the density cut-point in cyclones is higher than the operating medium density, while, in cylindrical vessels, the density cut- point is closer to the medium density. The results provide an interesting description of the differing behaviors of conical and cylindrical vessels, and they help explain the differences in pegormance between the two types of separators.

Jan 1, 2000

By Yang Ge, Yuzhu Pan, Mansheng Chu, Jue Tang, Cong Feng, Lihua Gao, Zhenggen Liu

The low-grade nickel laterite ore used in this study was successfully upgraded through selective reduction by industrialized rotary kilns followed by magnetic separation. The results indicated that both iron metallization extent and nickel metallization extent showed obvious linear correlation. In addition, rational roasting temperature and prolonged grinding time could enhance the overall fineness level of reduced laterite nickel ore. The moderate roasting temperature at a range of 1100–1150 °C should be suitable enough to a conversion of total nickel to metallic nickel and partly inhibited the conversion of total iron. Ultimately, the obtained ferronickel alloy with a nickel content of 7.32% and an iron content of 84.15% was prepared successfully from the lowgrade nickel laterite ore containing a nickel content of 1.92%. Nickel and iron recoveries were 96.72 and 89.08% respectively, which achieved the highly efficient recovery and utilization of iron and nickel from low-grade laterite nickel ore

By J. J. Harrington

The pH control system at Kennecott Copper Corporation's Nevada Mines Division concentrator consists of two independent systems, lime dilution and lime addition. Lime dilution is accomplished in a mixing tank where slaked lime and water are introduced proportionately. The desired dilution of the milk of lime is determined by the electrical inputs provided by eight pH probes, one per grinding section. The inputs are averaged and applied to a time base generator. The summation output of the time base generator determines the proportion of lime and water that are to be mixed and applies this input to a voltage sensitive switching device. The switching device provides a signal to one of two relays which will add either slaked lime or water, dependent upon the summation output. The entire cycle is based on a two-minute repetition rate to allow for sufficient mix time. Responsivity is controlled by maintaining a limited maxi- mum solution level in the mix tank. Lime addition is controlled independently within each grinding section. The electrical input from the pH probe in a given section controls the solenoid valves which provide lime to each of the ball mills. The valves remain open within a time range capable of maintaining the pH of flotation feed at a given set point.

Jan 1, 1975

By William D. Hanson

Celestine (celestite) (SrSO4), the primary ore mineral of strontium, is present in the DeQueen Limestone Member of the Trinity Group (Lower Cretaceous) in Sevier, Howard, and Pike Counties, southwest Arkansas. Two mappable celestine beds have been identified. One bed is commonly 3-5 in. thick, but ranges up to 18 in. in thickness; the other bed is generally 2-3 in. thick. The beds are concordant within the DeQueen Limestone and were formed by precipitation from periodically restricted sea water. Reports concerning celestine date back to 1929, when Hugh D. Miser and A. H. Purdue mapped the geology of the DeQueen and Caddo Gap quadrangles. A small amount of celestine was produced in the early 1940s in Howard County. During 1941, the J. W. Hintze Company collected 1,500 pounds of celestine for testing purposes. In 1942 and 1943,750 test holes were drilled by the Bennett-Clark Company in Howard County. Afterward, approximately 90 tons of celestine was open-pit mined and shipped to Texas for processing. Since then, no mining of celestine in Arkansas has taken place.

Jan 1, 1999

By J. C. Yingling, R. J. Sweigard, S. T. Mickleborough

The geostatistical technique of conditional simulation is applied to measure the uncertainty inherent in the factor-of-safety (FS) predictions for soil slopes in which there is an incomplete knowledge of the spatial distribution of soil properties. A case study that considers a natural clay slope in Canada is presented. The sequential-indicator simulation technique was used as a means of generating a series of spatial maps of the soil properties at the site. These maps approximate random draws from the conditional probability density function that characterizes existing uncertainty in the spatial distribution. FS determinations were made for each simulated map using the simplified-Janbu approach. In using this approach, computations are performed using a new computer program that can operate on irregular spatial profiles of soil properties specified on a discrete grid. A unique capability of this approach is the ability to generate the FS distribution conditional to the type, position and value of existing site-characterization measurements. This capability should reduce uncertainty in FS predictions.

Jan 1, 1996

By George Hufford

An investigation is made into the applicability of queueing theory to simulating the operation of a large open pit copper mine in the southwestern United States. Actual data from a working mine was used to construct curves for truck loading time, haulage and return time, and dumping times. Known results of investigations of queueing models (Koenigsberg - 1958, Gordon and Newell - 1967, Cabera and Maher - 1973) were used to simulate the actual operation. These did not give acceptable results so commonly used probability distributions were fitted to the actual data. A large computer program known as Q-GERT was used with the various parameters obtained from fitting the curves. Kolmogorov- Smirnov tests were run that showed that this was not satisfactory either. Finally, Q-GERT was used with the actual data from the mine. An appropriate correction factor is then found to apply to the exponential probability distributions tested previously and satisfactory results are obtained.

Jan 1, 1981

By D. Jepsen

Land access and tenure certainty for exploration and mine development is absolutely critical to the foundation of a healthy, sustainable and environmentally-sound mineral exploration and mining sector. Without certainty, mineral exploration will be severely eroded, resulting in reduced possibility of discovering and developing new mines. The development of positive relationships based on a shared commitment of understanding, mutual respect and trust by First Nations and the mineral sector can provide this increased business certainty and social and economic benefits for local First Nations. As a sector, we face many challenges in regard to building relationships with First Nations. The root solution to addressing these challenges lies in recognizing and understanding the unique cultural differences that exist between indigenous people and the business community. From the Canadian perspective, the First Nations culture differs vastly from non-Aboriginal culture. It is equally as imperative that cultural differences be acknowledged and respected at home as they are when seeking business opportunities in other countries. The traditional “business” approaches and relationships that one understands and incorporates with one’s contractors, legal counsel, investors and Board are generally not be the best approach for the introductory and subsequent meetings with indigenous peoples. This paper is written from the perspective of my experiences accumulated over the past ten years, first as Manager of Aboriginal Affairs for one of the largest forest companies in British Columbia and now, as President and CEO of the Association for Mineral Exploration BC (AME BC). My opinions are not necessarily endorsed by AME BC. Before the gritty issues of consultation and benefit sharing are dealt with, it is worthwhile to clear up the confusion surrounding terminology. “Indigenous Peoples” is used in a global context; “Aboriginal Peoples” is used in the Canadian context therefore includes Métis, Inuit and First Nations Peoples. The term “First Nations”, in the context of British Columbia, perhaps has its roots in the fact that treaties have largely not been settled. Therefore it is important to reaffirm that British Columbia was not discovered. First Nations have resided in British Columbia since time immemorial.

Jan 1, 2007

By Alten F. Grandt

Surface mining consists of the removal of the geologic strata overlying the coal seam usually with large electric shovels, draglines or bucket wheels. The method produces more or less parallel ridges or peaks of cast overburden, usually called "spoil banks". The mined lands vary widely in their inherent characteristics to produce a vegetative cover and thus can be put to a wide variety of uses. Use is the key to economic and social benefits. Physical and Chemical Characteristics of Soil Material of Surface Mined Lands after surface mining operations, the soil material is a heterogeneous mass whose physical and chemical properties are dominated by the character of the geologic strata overlying the coal. These strata are highly variable in thickness and character. They may include the surface soil, loess, glacial till, sands, shales, slates, limestone and sandstone rock. The method of mining with the several types of mining equipment will also affect the resultant mined area.

Jan 1, 1968

By Allan M. Johnson

Dewatering is a major operational cost at sane mines. Under certain conditions, costs associated with water disposal may continue beyond the productive life of the mine. For mines with mineralized waters, this is of special concern. Since 1974 experience has been gained from the examination of a number of closed underground metal mines that exhibited drainage problems. It was observed in certain cases, that had appropriate steps been taken prior to closure, that the resulting drainage problems could have been largely avoided. The pre-closure steps would have involved alteration to the "plumbing system" of the mines: i.e., the drifts and crosscuts interconnecting the workings of the mine. This could have best been accomplished by the placement of bulkheads and/or selective drifting. In addition to reconfirming that hindsight is 20-20, a lesson learned from these case studies shows that a relatively simple hydrologic evaluation prior to mine closure may avoid a troublesome and costly drainage problem.

Jan 1, 1983

By E. A. Devuyst, G. Robbins

A unique process for removing cyanide and base metal complexes from industrial waste streams was patented by G.J. Borberly et al. (1984). The process uses SO2 (liquid or gas, or solutions of sulfite salts, or from burning elemental sulfur), plus air that is dispersed in the effluent using a well agitated vessel. Acid produced in the oxidation reactions is neutralized with lime at a controlled pH generally in the range 7 to 10. The reaction requires the presence of soluble copper as a catalyst which can be supplemented by copper sulfate if necessary. The process can be applied to the detoxification of gold and silver mining waste streams, such as carbon-in-pulp (CIP) tailing pulps, barren solution bleeds, pond waters and heap leach rinse solutions and also to plating shops wastewaters. The SO.jAir process has substantial advantages over two of the main alternative methods of cyanide destruction, namely alkaline chlorination and hydrogen peroxide. Alkaline chlorination is highly penalized in terms of reagent consumption. Chlorine is a strong oxidant reacting with species other than cyanide present in the effluent such as thiocyanate and sulfides. Furthermore alkaline chlorination is an incomplete detoxification process. Iron cyanide is not removed and the potential for harmful by-products species exist. Consequently final effluents may be subject to additional treatment in order to comply with regulatory demands.

Jan 1, 1991

By T. R. Jr. McMillan

Introduction Examining the short- and long-term job prospects for engineers in the coal industry might include looking at coal tonnage projections, future export markets, federal regulations, and the decrease in overall graduates. But coal is the US most competitive basic industry. As such, why not go back to basics? That is, there are three basic challenges that need to be faced by students, faculty, and members of the coal industry. These challenges are counseling, career placement, and professionalism. Counseling Counseling can include elementary, high school, and college students, as well as individuals already employed. But what happens to students after they have selected a course of study at a particular university? As shown in Fig. 1, only 87,000, or 7.25% of our graduates have technical degrees. Generally, there is a strong market projected for these engineering graduates. However, many students who have majored in other nontechnical curriculums, have to scramble for jobs. This says something about our ability to make students aware of where the real job opportunities are. As a student spends four or five years pursuing a degree, he or she is looking for professional guidance. The student has the right to expect "real world" counseling - counseling that is not "the way it should be" but "the way it is." The influence of faculty members is significant. They should take this long opportunity to tell students not what they want to hear or what the problem's of academia or the industry are, but what the real job market is all about. If faculty do not use this opportunity, they in-advertently-through omission - mislead their students. Once a student graduates and is a working alumnus, faculty should take advantage of their relationship with the student and continue to stimulate conversation leading to a two-way exchange of ideas and information. Faculty should also encourage and solicit financial support for their mining departments from their alumni. These monies, in many cases, will be matched dollar for dollar or more, depending on the company the alumnus works for. In the private sector, the responsibility is to communicate with faculty and students. Alumni can be effective by participating in this two-way dialogue with their professors at meetings, technical seminars, and conventions. In many cases, alumni will employ summer or co-op students in their organizations. While getting to know these students, industry members should level with them on where the true opportunities are and what it takes to be successful. It is important to communicate with both faculty and students candidly on both the posi-

Jan 2, 1985

By M. Govinda Raj, S. Sridhar, M. Aruna

Hand-transmitted vibration (HTV) exposure is associated with various health risks for operators of mobile mining equipment (MME). The case–control research was conducted to determine the musculoskeletal disorder (MSD) risks associated with exposure to HTVs in the exposed (case) and non-exposed (control) groups. HTV readings were measured at the interface between the hand and the steering device using the SV 105B triaxial hand accelerometer connected to the SV106 human vibration analyzer involving 40 MME operators in accordance with ISO 5349:2001 guidelines. A questionnaire survey was also carried out among both the study groups using Cornell Musculoskeletal Discomfort Questionnaire. The European Union's 2002/44/E.C. was used to assess the health risks posed to the MME operators. Twenty-eight out of the 40 MMEs were generating HTVs exceeding the stipulated daily limits of vibration, putting 70% of the operators at increased risk for developing MSDs. The case group was found to have an elevated risk of exposure with odds ratio (OR) 7.56 (95% confidence interval (CI), 1.159, 49.39) and OR 12.80 (95% CI, 2.436, 67.285) times more likely than the control group to suffer discomfort in the left shoulder and left wrist, respectively, indicating increased risk of exposure to HTV. Additionally, cases had elevated risk associated with exposure to tobacco, OR 9.35(95% CI, 1.856, 47.129) compared to those who did not use tobacco. MSDs were more prevalent in the case group compared to the control group. This observation was validated by the field investigations and the responses of MME operators to the questionnaires.

Aug 2, 2022