Search Documents

The dissolution kinetics of cobalt in iodine/iodide solutions was investigated using a rotating disc technique. Variables studied here included temperature, rotating speed, concentration of lixiviants, and pH of the solution. The overall dissolution reaction was found to be limited by mass transfer of tri-iodide through the diffusion boundary layer with Arrhenius activation energy of less than 16.2 kJ/mol (4 kcal/mol) over the temperature range, 2-42°C. The pH of the solution had little effect as long as the pH of the solution was less than 8. However, when the pH of the solution became greater than 8, the dissolution rate decreased dramatically due to passivation. The rate of dissolution was in good agreement with the dissolution model developed by the authors earlier.

Jan 1, 1994

By P. Mousset-Jones, F. Calizaya

Ultrasonic anemometry is a relatively new method of measuring the air velocity in underground excavations and is not widely used. The method has been mainly used for surface applications, such as meteorology and fluid flow measurement. Several instruments were looked at to determine their applicability for continuous underground monitoring systems. The units fall into two main categories: variable distance units and fined distance units. The method relies on the acceleration and deceleration of ultrasonic pulses transmitted through a moving airstream. This study presents some of the results of the testing of variable and fixed distance ultrasonic anemometers in a wind tunnel and a mine drift.

Jan 1, 1995

By Robert Hochscheid

A patent issued to J.N.J. Leeman (1957) described the change in performance that takes place when a cyclone is installed in the horizontal position rather than the vertical position. Although this patent was directed more toward improvements that could be realized in the heavy medium cleaning of coal, it contained specific references to reducing the quantity of fine solids that would report in the underflow, and an example for fine sand classification is also included. The three cyclone installations for which data is given in this paper demonstrate that horizontal mounting of large cyclones can improve classification efficiency, eliminate some operational difficulties, and reduce cyclone maintenance requirements in closed circuit grinding installations. Cyclone Experience at Serrana S.A. Each of four grinding circuits at the Serrana S.A. de Mineracao Apatite flotation plant in Brazil have a 2.7 X 4.6 meter (9 X 15 foot) rod mill and each originally operated in closed circuit with two vertically mounted Model D20B (500m nominal diameter) Krebs Cyclones. New feed size is 25mm. The Apatite is liberated at a relatively coarse 35 to 28 mesh grind, but the 500mm cyclones had to be fed at 66 pct. solids in order to obtain an overflow analyzing 12 pct. coarser than 42 mesh. Because dilution water in the cyclone feed had to be limited, classification was inefficient, and there were other significant circuit difficulties as summarized in a recent article by C. A. Busnardo (1984):

Jan 1, 1985

By G. Ferrara

Hydrocyclones and other dynamic separators are normally fed with pulps of water and solid particles. The particles have different sizes, shapes and densities and, except in the special case of mono-characteristic particles, are segregated into size, shape and density. Segregation is magnified by the high values of centrifugal acceleration in the hydrocyclones. This paper develops the theory of the segregation, indicates the major variables involved and reports experimental data of segregation under different operating conditions for mixtures of magnetite and/or ferrosilicon and non-magnetic minerals.

Jan 1, 1995

By Deepak Malhotra, Linda Battich

INTRODUCTION Mineral processing plants generally operate efficiently within the technical, economic and management constraints applied to them. They have no choice, because the dynamic and competitive nature of the mineral business dictates that survival and/or prosperity of the company depends on being a low cost producer. Progressive mineral companies realize that market downturns will occur, and they must continuously strive for lower unit production costs rather than be satisfied with the status quo. Mineral companies generally tend to reduce costs during market downturns. This short-term solution is achieved by high grading of ores, and cut-backs In waste stripping, exploration, and capital expenditures.(1) However, to remain a low-cost producer in the long term, companies must enhance revenue and reduce cost simultaneously. This Involves continuous evaluation of technologies and reagents, periodic audits to locate revenue losses; and gathering and analyzing statistical plant data to clearly understand the Impact of process variables on efficiency. Mineral companies are caught in a Catch-22. They need resources to accomplish the objectives outlined above. Most mill stuffs have been cut to the minimum level necessary to maintain production. Resources such as time, manpower and money are scarce, and mill metallurglsts struggle to use these resources productively. Is your flotation plant optimized? History Indicates that successful operations constantly tune the flotation circuits to Improve metallurgy or reduce cost. This Is the essence of evolutionary change In mineral processing operations. A plant auditing approach can play a key role in assisting the process engineers to achieve the overall objective of enhancing metallurgy and reducing cost with limited resources through evolutionary improvements. FLOTATION SYSTEM The flotation process is the most widely wed concentration process In the world today. The number of variables that can affect the flotation results Is very large, maybe over 100. These variables can be divided Into three main groups: (2) (1) ore and mineral properties; (2) reagent treatment; and (3) flotation machine characteristics. Some of these variables can be controlled while others have to be accepted. Recently, Investigators (3,4) have attempted to describe the flotation process as an engineering system which includes chemistry, equipment and operating variables. Though some of the variables are Independent, most are co-dependent. thus making it difficult to develop simple cause and effect relationships. For example, it is easy to understand the effect of reagent change on recovery and grade In the rougher circuit, but very difficult to quantify Its impact on filtration downstream. Plant audits on a periodic basis are necessary to develop an understanding of the Interactive nature of the system. Auditing provides comparisons of plant operating performance before and after variable changes. OVERVIEW OF PLANT AUDITING An audit Is a formal, thorough and periodic examination of a system. There are various types of audits (i.e., geological, environmental, metallurgical. economic, etc.), and each serves a different purpose. (5) The discussion here is related to plant and/or metallurgical audits. Neale and Flintoff note that two key factors governing changes In an operation are: (1) the opportunity must be recognized; and (2) the justification for change must exist. (6) Both factors emphasize the critical role of successful plant auditing. Without plant audits. many opportunities for improvement must go unrecognized. On the other hand, when a situation ripe for improvement Is recognized. the hard data from a plant audit can reveal the expected impact of an operating change.

Jan 1, 1993

By A. W. Khair

This paper presents an analysis of the dynamics of bit wear on the productivity of the continuous miners. Two field surveys have been carried out. The first survey was to assess the impact of bit wear on productivity and production cost. The second survey was to study the wear characteristics of the cutting tool (i.e. magnitude, forms, and mechanisms of bit wear). Primary factors affecting bit wear is identified and laboratory experiments were carried out to study the effects of some of these primary factors on wear in detail. Results indicate that bit wear has a significant effect on the productivity of the continuous miners. Furthermore under the severe geologic conditions (i.e. cutting rock partings and roof and floor rocks) bit wear not only hampers the productivity, but also increases the production cost due to a higher number of bit consumption. This study also indicated that bit wear accelerates beyond 20% of the conical height loss which corresponds to 7% of the weight loss. This increase rate of wear is an indicative of higher abrasion between bit body and cutting material, resulting in a dustier environment.

Jan 1, 1993

By T. W. West

INTRODUCTION This paper presents an assessment of conventional flotation technology. In addition it presents some ideas which can be used to change the perception of what may be done with conventional flotation equipment to maximize its efficiency. Perspective of Conventional Flotation Technology 1. Flotation in many coal preparation plants is defined as something between a necessary evil and a non-viable concept because: -Too much art is required on a continuous basis to achieve uniformly acceptable results. -It is expensive, the capital cost in dollars per ton of circuit feed for flotation and dewatering is high. -It is a difficult process to use when SO2 reduction governs system design and equipment selection. -It creates a product (fine coal froth) that is difficult to dewater in the presence of BTU/lb as-received pressures. -It is a difficult process to control from a management standpoint, there are no dependable set points to rely on. 2. Many froth cell circuits are 0.5m x 0 (nominal 28 M x 0) feed which is sourced from screen/cyclone underflows. The original intent was to obtain maximum yield at acceptable product quality and moisture using disc filters. (See Figure #1) 3. An alternate to conventional flotation and its perceived to be limits of efficiency, capital costs, etc. is to move towards such developing flotation technologies as column flotation, reverse flotation, and microbubbles. A lot of work is being done to move these concepts thru pilot stages into full scale, commercial plant operation. The majority of the coal producers and coal preparation plant designers view these concepts as being in the development/pilot plant stages. OBJECTIVES Based on the preceeding comments of the perspectives of the coal producers and plant designers, the options are limited. They can make do with what they have available to them in the way of industry standard equipment and practices or they can move forward with developing technology. I feel there is a third option: what can we really do today with what is available to us, without reinventing the wheel? APPROACH 1. When processing coal against ash and SO2 restrictions, the fine clean coal stream can be the best stream on the clean coal conveyor due to the release by size and the ability to create a high BTU/low sulfur (dry basis) product. 2. Targets: -Consistent raw coal size consist in the plant feed . -Do not put pyrites in the froth cells. -Adjust criteria defining good flotation away from yield towards maximum BTU recovery at minimum ash. -Limit the froth cell feed size consist to 0.15 mm x 0 (nominal 100M x 0). -Establish and maintain a correct, consistent percent solids in the froth cell feed. -Select flotation reagents with care. -Introduce reagents in the proper sequence.

Jan 1, 1988

By Paul Soros

Lord Robens, Chairman of the National Coal Board of England announced recently to the world press plans for construction of the largest bulk terminal in Western Europe. This should result in annual freight savings of 22.4 million dollars and between 150 and 190 million dollars of new export business. These are rather substantial amounts for any mining enterprise. Or to put it another way, opportunities to make substantial savings in the delivered price of a highly competitive commodity such as coal are few and far between. One area where such opportunities still exist is in the economical; movement of bulk materials between producer and consumer.

Jan 1, 1966

By R. Mathur

Cu isotope fractionation in low temperature aqueous environments has been well documented. Here we apply Cu isotopes to two distinct, yet related mining problems. First, an exploration geological application where we measured copper isotope fractionation in oxidized leach caps, chalcocite enrichment blankets and hypogene mineralization in 4 porphyry copper deposits located in South western USA. Cu isotope patterns exist in the lateral and vertical distribution within the mines coupled with distinct relationships with Cu grade. Second, a hydrometallurgical application where we measured the leach fluids, feed and residues from a quick leach text of Cañariaco ores. The results indicate the relative proportions of the minerals providing Cu during leaching. Interpretations of the QLT test measurements indicate covellite is the dominant ore mineral providing Cu during leaching. Both applications clearly demonstrate the power and ability of using the Cu isotope technique to understand low temperature aqueous processed involving copper.

Jan 1, 2010

By R. Stefanko

Rock bolting as a method of support continues to increase with applications in many other industries in addition to mining. Nevertheless, with nearly 55,000,000 roof bolts installed in coal mines alone last year, this remains as the single greatest use. While bolts have frequently supported ground where conventional timbering could not, there are relatively few design criteria; and trial-and-error procedures prevail. Furthermore, development of suitable instrumentation that is simple to install and readout, sensitive, durable, reliable, safe and economical in evaluating the effectiveness of a bolt over long periods of time lags behind. Therefore, the pull test continues to be the most popular method of evaluating the applicability of a certain type of roof bolt under specific installation conditions. At Penn State in the Department of Mining, research has been conducted for a number of years to measure bleedoff in carefully controlled laboratory experiments as well as in underground investigations.1,2,3,4 Unfortunately, most of the instrumentation developed has been primarily suitable only for research purposes, not possessing all of the aforementioned characteristics desirable for routine underground use. Other groups also have met with restricted success. Therefore, while relatively crude, the torque wrench continues to remain as the most widely used load measuring device. While both field and laboratory tests continue to be conducted, analytical analyses are attempted to discover the more important design parameters in order that more efficient anchorage might be devised.

Jan 1, 1969

By Jun Ho Lee, Dae Young Kim, Ebrahim Farrokh, Ki Chang Hyun

"The Jinhae Geoje gas pipeline tunnel project is the largest (7.8 km) and the deepest (90 m) subsea tunnel in South Korea. This tunnel will house a pipeline to carry natural gas from the mainland to Geoje Island southeast of the country to alleviate the increased demands for natural gas, especially in the winter season. Tunneling is currently underway using two slurry shield TBMs of 3.5 m diameter. This paper describes the major design elements of the tunneling machines and their performance evaluation. For this purpose, a thorough analysis of geotechnical information was performed to evaluate the tunnel elevation to reduce the risk of tunneling under high water pressure in unstable and permeable rock mass under 9 bar water pressure. TBM specification and TBM performance were also analyzed using different methods, including well-known models as well as a rotary cutting machine test developed in house in Hyundai Engineering and Construction Company. INTRODUCTION High demand for natural gas, especially in winter season was the primary driving factor for the design of the Jinhae Geoje gas pipeline project. This project is located southeast of South Korea between Jinhae district and Geoje Island and runs for over 50 km length. The mid part of this project includes a 3.5 m diameter subsea tunnel consisting of two sections of Geoje to Jiri Island (4.3 km) and Jinhae to Jiri Island (3.5 km). Figure 1 shows the tunnel project location and its layout. Figure 2 shows the geological profile along the tunnel. As can be seen, the tunnel passes mainly through three rock types: granite, tuff breccia, and andesite tuff. This tunnel was planned to be constructed by two face pressurized shielded TBMs and to be lined with a segmental lining of 2.8 m internal diameter. The major challenge for this tunnel is its maximum expected water pressure at the tunnel invert (8.83 bar). At such a high water pressure, the TBMs required special design to ensure they can handle unexpected water pressure and to ensure the risks for the TBM maintenance intervention are minimal. In this regard, a thorough analysis was conducted on the TBM design parameters and geotechnical information to define required TBMs’ design parameters and to identify the safest tunnel elevation. This paper provides a brief overview of the project geotechnical information, TBM selection and its design specification, tunnel elevation selection, and TBM penetration rate evaluation. In this regard, a rotary cutting machine testing equipment was used to perform trial tests on a similar rock type encountered along the tunnel for performance evaluation and optimization."

Jan 1, 2016

By Thomas P. Kwiatkowski, Len Cobb, Christopher D. Orlandi, Judith H. Jones

The Inland System supplies raw water to the industrial and domestic users in the City of Birmingham, Alabama. The Inland System, which is nearly 60 years old, consists of an approximately 57.9m (190 feet) high earthen dam across the Blackburn Fork of the Black Warrior River, a 39.6m (130 feet) high reinforced concrete intake structure, a 1524mm (60inch) diameter Dresser coupled steel transmission pipeline, and various distribution lines extending into Birmingham. The Inland System was owned, operated and maintained by the Industrial Water Board (IWB) of the City of Birmingham, an agency of the city government, from 1958 until 1994. In 1994, the City of Birmingham consolidated all water and distribution functions under the Birmingham Water Works Board (BWWB). In 1988, the IWB determined that the Inland System had reached a point where its reliability could not be assured without an in-depth evaluation and renovation. The IWB engaged Christy/Cobb, Inc. (CCI) of Birmingham as its consultant for the renovation work. CCI evaluated the Inland System and submitted a report to the IWB in April, 1992. The report contained several recommendations for capital improvements to the system including increasing the emergency spillway capacity, reconstructing the fuse plug, relocating public access to the lake away from the dam area, constructing a new intake structure, and constructing a tunnel through the dam abutment to deliver the water from the proposed intake structure to the existing 1524mm (60 inch) diameter supply line. The new intake structure and tunnel would provide for a future maximum demand flow rate as well as provide bypass and level control capabilities. CCI was authorized in 1992 to proceed with the engineering design for the renovation of the Inland System with emphasis on the spillway and intake structure. PROJECT DESCRIPTION The major component of the renovation of the Inland System was the new intake structure and tunnel through the dam abutment. CCI engaged Jenny Engineering Corporation (JEC) of Springfield, New Jersey as a consultant for the tunnel design. JEC was responsible for the design of the tunnel, the connecting shaft between the intake structure and tunnel, and the steel pipe final lining, while CCI was responsible for the intake structure and the connection to the existing supply pipeline as well as overall project management. CCI and JEC evaluated the project site in order to select the location for the new intake structure and set the alignment for the tunnel. A factor in the evaluation process was that the level of the lake could not be lowered to construct the new intake structure since the supply of water from the Inland System had to maintained. Therefore, a location was required which was

Jan 1, 1997

By S. Page, R. Bhaskar

The development is described of a real-time tracer gas sensing system for use in fell-scale laboratory studies of air flow behavior around mining machines. A semiconductor sintered tin-dioxide gas sensor is used for gas analyses. A data acquisition and analyses software specific to the sensor characteristics was also developed as part of the system. The system permits the study of transient behavior and assists in obtaining a better understanding of the movement of air around mining machines and in the study of the effect of potential airflow modification devices on the dust exposure of face personnel. It seeks to replace the current method of using a centralized infrared gas analyzer that polls several sampling points using an array of solenoid valves and gas line purgers. The polling results in a significant time lapse between the first and the last set of readings. The system described in this paper has the advantages of real-time sampling and safe operation.

Jan 1, 1992

By L. Meier, M. Dennis, J. Schieffer, K. Murray

"INTRODUCTION Contrary to popular belief, Arizona State Trust land is not public land. All uses of the land must benefit the Trust, a fact that is considered with the review of each application received for sale, lease, or permit. This includes applications for activities ranging from commercial development to recreation. In 1863, the Territory of Arizona was established by an act of Congress. This act reserved sections 16 and 36 in each township to be held in trust for the benefit of the common schools. Later, the Enabling Act of 1910 allowed the Territory of Arizona to prepare for statehood. This act reserved the additional sections 2 and 32 of each township for the common schools and granted another 2,350,000 acres to be held in trust for other beneficiaries. In all, Congress granted the State of Arizona almost 11 million acres. The State was to manage those lands and maximize revenue for 13 separate beneficiaries. To meet this mandate, the State established the Arizona State Land Department (ASLD) in 1915. During fiscal year 2015, the ASLD contributed $136 million to the permanent fund, bringing the total value to over $5.1 billion, through the sale and leasing of the land and natural products which includes minerals. The current inventory of State Trust lands includes 9.2 million acres representing about 12.7% of the State.The ASLD Minerals Section manages the exploration, development, and leasing of mineral products on State Trust land. We are not a regulatory agency, but a department guided by our fiduciary responsibilities to the Trust. Our mineral programs include: Exploration Permits, Mineral Leases, Mineral Material Leases, Geothermal Leases, Oil & Gas Leases, and Special Land Use Permits. INDUSTRIAL MINERALS ON ARIZONA STATE TRUST LAND Industrial minerals fall under the category of either Mineral or Mineral Materials Leases. Common industrial minerals found on Arizona State Trust land include potash, limestone, gypsum, salt, specialty clays, zeolites, crushed stone, and sand and gravel."

Jan 1, 2016

By Greg Sanders, Michael Gilbert, James G. Shaughnessy

"A new raw water intake from the South Holston River to the Kingsport water treatment plant is under construction. The exploration for the 335 meter long horseshoe shaped tunnel design took advantage of the site topography along the alignment to better define the complex geology consisting of Knox Limestone and Sevier Shale formations separated by a fault zone. To assess the geological conditions and to determine the extent of the fault zone, a 183 meter long horizontal boring and geophysical investigation was performed along a portion of the tunnel’s horizontal alignment. Explorations defined the fault zone width at approximately 5 meters and packer testing along the alignment provided a means of estimating groundwater inflows. As the tunnel excavation advances, comparisons of exploratory data versus encountered conditions will be made. This paper provides details on the geotechnical investigation, lessons learned, and the influence of the geology on the tunnel design. PROJECT OVERVIEW The Kingsport WTP is supplied with raw water via the South Holston River. The City of Kingsport (City) owns and operates the Kingsport Water Treatment Plant (WTP). The existing raw water intake system, consisting of pumps, power supply, raw water piping and appurtenant facilities has been determined to be vulnerable to failure. The original Raw Water Pump Station (RWPS) was constructed in 1928 as part of the original Kingsport WTP project. The 1928 RWPS operated until 1970 when it was replaced by the existing RWPS. This existing system still utilizes the 1928 piping and piping tunnel. Improvements to the RWPS hydraulics and capacity are required to meet the City’s future water treatment needs. The system extracts water from the South Fork of the Holsten River and coveys it via three pressure pipelines to the WTP. The conveyance piping exits the RWPS, ascends approximately 23 m up a near vertical rock outcropping then enters a 120 m long tunnel. Upon exiting the tunnel the piping continues underground to the WTP. The drill and blast tunnel is horseshoe shaped and nominally 3.3 m high by 3.3 m wide. The easternmost 62.3 m of the tunnel is without any type of support. The remainder is lined with concrete. According to the City of Kingsport, the concrete lining was installed in the 1970’s as part of upgrades to the facility. An evaluation of the current facilities concluded that the conveyance piping was in poor condition and required replacement."

Jan 1, 2016

By Mark C. Holton

The mining industry has recently been. - experiencing a difficult period. Escalating costs, lower grades and deeper level mining, are a few of .the reasons' why interactive graphics or CADD (computer aided design and draughting) systems are increasingly being used. CADD systems which support powerful and flexible mining applications have great potential for making all forms of mining more efficient and effective. There are many application programs which address almost every aspect of mining. Most of these programs originated to satisfy a particular need. Graphics and other features were added until they, reached a point where they were commercially viable as a mining package. Because of their evolution these packages, lack many CADD-type features. Today there are powerful personal computers (PC's) and engineering workstations running the best CADD systems available. These systems, support hundreds of applications in almost every discipline. Mining was until recently not well supported by interactive graphics vendors because of the highly variable nature of mining and the lack of common standards. Users of CADD systems have experienced the benefits of CADD and come to expect similar features from graphic mining packages. Several developers of mining packagers have either attempted to include some CADD features or make their packages compatible with one or other CADD system. Mining can benefit greatly From a combination of interactive graphics (or CADD) and the right mining application software.

Jan 1, 1989

By Christopher J. Bise

INTRODUCTION Traditionally, the purpose of mine ventilation has been defined as diluting, rendering harmless, and sweeping away hazardous gases which may accumulate in the mine workings. In addition, the ventilation sys- tem must keep the mine air as close as possible to the composition of the outside air in order to provide a healthy environment for mineworkers and to prolong the useful life of mine equipment. When plans are being developed for opening a new mine, sound engineering dictates that a calculated estimate be made of both the maximum air quantity requirement and the accept- able mine pressure (head) loss related to the under- ground layout and projections. For efficient mine ventilation, the two problem areas that demand constant attention are (1) the control of fugitive air (through short circuiting or leakage) and (2) the provision of ample airway capacity. Fugitive air is that quantity of air which enters the mine but short-circuits the mine ventilation system through improperly constructed stoppings, doors, overcasts, etc.; it represents an investment in power consumption (to move the air by the fan) while providing little, if any, return on the investment. Typically, efficient mines are those that can deliver 50% of the air handled by their fans to the working faces. Paying close attention to a new mine's ventilation system at the outset can provide numerous benefits during the later stages of mine development. It has often been noted that the main cause of trouble in many mine ventilation systems can be found within a radius of 2500 ft from the fan installation. Ample airway capacity is essential to maintain the mine's head loss within manageable limits. Similar to an industrial ventilation setting, the mine's headings are the ductwork for the handling of air. The difference between normal industrial ventilation and mine ventilation is apparent when more capacity is needed; a plant can install new or larger ductwork, but it is difficult for a mine to install new entries or enlarge existing entries. Air velocities are usually maintained under 800 fpm to limit the stirring up of dust in the intakes. With this in mind, it is usually simple to estimate the number of entries required in the ventilation system. The problem that often arises, though, is when the system's capacity is overestimated and the required head loss to achieve the desired quantity is excessive. Experience has shown that problems are often encountered when the mine's condition requires much more than three inches of water gage to ventilate the mine on a day-to-day basis. Thus, if proper attention is not paid to these parameters in the preplanning and initial development of a new mine, it may take an extremely high water gage to achieve the ultimate quantity. This chapter will not delve deeply into the theory of mine ventilation; many other books have been writ- ten on that subject. Instead, the following sections will point out the important considerations that should take place before the development of a mine ventilation system, as they relate to normal industry practice. FUNDAMENTALS OF AIRFLOW Volume Versus Water Gage The common method of measuring ventilation pressure is in terms of inches of water gage (wg); one inch of water corresponds to a pressure of 5.2 psf (pounds per square foot). Further, airflow follows a square-law relationship between volumes and pressures where, as shown in the previous section, a doubling of quantity requires a quadrupling of pressure. Table 1 shows how heads and quantities are related. Using Table 1, it is readily apparent that, for the same mining conditions, an increase in pressure from one inch wg to three inches wg results in only 34,640 cfm when the initial quantity is 20,000 cfm. Pressure Losses Pressure losses in mine ventilation systems are caused by friction between the heading walls and the air stream and by shock losses due to abrupt changes of the air stream caused by obstructions. The common pressure-loss formula for mine ventilation is: [ ] where H is the pressure loss in inches of water gage, K is the coefficient of friction, L is the length of the airway in feet, 0 is the airway perimeter in feet, V is the air velocity in feet per minute, and A is the cross-sectional area of the airway in square feet. Table 2 lists the US Bureau of Mines schedule of friction factors (K) for mine airways. Recent research indicates that the values of K are slightly less for coal mines than those presented in the USBM Schedule, and Table 3 should be consulted in this instance. It should be

Jan 1, 1986

By Sergio Flores, Nate Long, William Hodder, Phil Rhodes, Tim McQueary

The Surface Water Supply Project Segment B3 is a 4 miles section of tunnel that will run East- West in Houston TX, from Hopper St to I-45. The tunnel will be mined by using a 128" Dia refurbished 1987 Lovat Tunnel Boring Machine capable of operating in Open or EPB mode. The tunnel will be temporarily supported with ribs and lagging and a 96" Dia pipe will be grouted into place. All four miles of this project are within Petroleum Pipeline Easements. The project includes seven shafts, 2000' of tunnel in potentially petroleum contaminated ground, crossing the Hardy Toll d, I-45, the nion Pacic ailroad ight of Way and multiple oil and gas pipeline crossings. This paper summarizes the planning and drive performed to date.

Jun 23, 2024

By B. A. Wills

With the increasing need to mine lower grade ores, high energy-related costs in comminution are of major concern. Very fine grinding is needed to liberate the very fine mineral particles in these ores. Not only is this expensive but it leads to greater losses in 'slimes'. In the early 1970's, 50% of the tin mined in Bolivia, 30% of the phosphate mined in Florida and 20% of the world's tungsten were lost in this way (Somasundaran, 1979). Gravity concentration techniques become unacceptably inefficient for particle treatment below 25-50µm, and even flotation fails in the ultra-fine range. Two approaches can be adopted to try to overcome this problem. The first involves increasing the efficiency of existing equipment or developing new slimes treatment processes. Gravity devices such as the Bartles-Mozley concentrator have been developed for this purpose and good recovery has been reported from 100µm down to 5µm. Such machines, however, have relatively low throughputs, so that large areas of plant space are generally required. Flotation is rapidly growing in importance for the treatment of ultra-fine minerals traditionally treated by gravity concentration.

Jan 1, 1986

By D. M. Thayer

Laboratory and pilot plant investigations have indicated that copper recoveries of 50% can be achieved with fine grinding and flotation of a copper reverberatory furnace slag, Microscopic and microprobe studies indicate that the recoverable copper is in the form of matte, chalcocite, and metallic copper; the percentage of copper in particles appearing to be copper-free was from 0.23 - 0.54%.

Jan 1, 1969