Search Documents

By M. F. Goodrich

The concept of using water-only cyclones as a clean coal scalping device preceding a heavy media cyclone circuit shows considerable promise, as it can considerably reduce the feed to the heavy media cyclone circuit. The system will not perform as well as a heavy media cyclone circuit alone, but the resultant loss in yield is small and may be negligible under some conditions. The concept of water-only cyclone scalping has previously been suggested by others. By reducing the amount of raw coal to be processed in the more expensive circuits overall capital and operating costs may be reduced. There are a few commercial plants with circuits operating on this concept. In the Warwick and Rowland plants water-only cyclones are used to scalp the feed to a heavy media vessel and Deister tables respectively while Amherst Coal Company's McGregor plant uses them to scalp the feed to a heavy media cyclone circuit. The system was evaluated on a technical basis, both from a theoretical viewpoint and by analysis of a computer simulation, in order to gain a fuller understanding of its usefulness and limitations.

Jan 1, 1977

By C. E. Tackett

The Greenwich Collieries Co. is a subsidiary of the Pennsylvania Mines Corporation, and a wholly owned subsidiary of the PP&L Co. which serves the northeastern portion of Pa. PP&L annually consumes about 11 million tons of coal per year and is the largest consumer of both bituminous and anthracite coal on the eastern seaboard. Development work for Greenwich started in 1969. The coarse coal plant was constructed in 1970, with the raw fines bypassed. This worked very well for our requirements at that time; however, the Greenwich mining plans were extensively changed, longwall mining units were installed and low coal was encountered, resulting in dirtier coal, a finer coal and an ever increasing ash in the shipped product. All this demanded a more efficient ash removal process for the fine coal fraction. In 1971, the Pennsylvania Department of Environmental Resources and the Federal Environmental Protection Agency were pushing for the now stringent sulphur emission limits at our power plants. The Greenwich Mine coal reserves contained large quantities of 3.5 to 4% sulphur along with some low sulphur reserves. It was, therefore, essential that any new plant have the capability of efficient sulphur removal to meet the Pennsylvania Department of Environmental Resources and the Federal Environmental Protection Agency required limits. To meet these limits our design would have to be capable of producing a product of 2.0% sulphur or less.

Jan 1, 1977

By John S. Livermore

I feel very privileged to be added to the distinguished group that has received this award since the first recipient, Reno Sales, received it in 1954. If my research is correct, the last geologist to be honored was Bill Callahan in 1982. Perhaps the Awards Committee decided it was about time to select a geologist, and I became the beneficiary. Regarding the discovery of the Carlin ore body, it was the culmination of several studies - one going back as far as 1939 when a US Bureau of Mines engineer named W.O. Vanderberg recognized an unusual type of gold mineralization in sediments in northern Nevada. What was unusual was the fact that the gold was so fine that it would not concentrate in a pan. This, plus the study of the Roberts Mountain thrust by Ralph Roberts (1960) and conversations with Harry Bishop, manager of the Gold Acres Mine, pointed Alan Coope and me in the direction of the Lynn Window and, eventually, the Carlin discovery. There has been a great deal written about this discovery. I thought it would be interesting to discuss the evolution of Carlin gold exploration in Nevada since this time and to discuss the changes in perception of this unique type of mineralization. The method used by Coope and me in following up on Roberts' work was to map geologically the Roberts Mountain thrust and conduct geochemical sampling of favorable outcrops and float. Coope was highly experienced in geochemical exploration, as he had graduated from the Royal School of Mines in London, studying under John S. Webb, one of the pioneers of geochemistry as applied to mineral exploration. We first considered using pathfinder elements, but finally concentrated on gold analyses alone, even though the sensitivity of fire assays used at that time was only about one-half part per million. According to the spatial relationship of the mineralization to the Roberts Mountain thrust, as pointed out by Roberts (1960), we were looking for mineralization within the thrust itself. Our models were the known Gold Acres and Getchell mines, which contained reserves on the order of 0.9 to 1.8 mt (1 to 2 million st). These were not of substantial size, but I had hoped we might find more than one of these tributary to a mill that would justify an operation for our employer, Newmont Mining Corp. What we ended up with was the type of deposit we were looking for - an open pit deposit of micron gold, which the old timers had missed because the gold was not capable of being panned. But never in our wildest dreams did we think there was a chance of finding a body containing 10 mt (11 million st) of ore at 0.30 oz/st (10.3 g/t).The deposit was not in the thrust proper but was found in a favorable horizon of Roberts Mountain siltstone that was below the thrust. This is the first example of how a model should not be followed blindly. Newmont was successful in keeping this discovery quiet for some time. After a considerable amount of drilling, a rumor circulated that they had discovered a large low-grade ore body of around 1.7 to 2.1 g/t (0.05 to 0.06 oz/st), which of course would not have been economic with gold at $1.13/g ($35/oz), which was the fixed price at that time. The company, for obvious reasons, did not discourage the rumor. When, however, the true results came out there was a lot of feverish activity. Because of this new type of so-called "invisible gold," which could have been missed by the old timers, the thought was that other deposits would be discovered very soon. The Carlin and other smaller deposits, including Bootstrap, Blue Star and Gold Quarry, were in windows where the lower plate of the Roberts Mountain formation (below the thrust) had been exposed by erosion. This then became the new

Jan 1, 1997

By William C. Dixon

Since the mid 60's, several haul cycle simulation programs have been developed. However, most of these programs are believed to employ the continuous, rather than the discrete, event-oriented simulation approach to determine the haul cycle times. This paper describes the recently developed haul cycle simulation approach where time is advanced in varying amounts only as the system changes occur. This approach results in greater computational accuracy and increased computational efficiency. The program is written in FORTRAN and requires equipment performance curve and haul road profiles as input. Unique program capabilities include the handling of switchbacks and intersections. The program uses a master data file concept in which various haul road profiles found during the mine life can be simulated all in one job submission. The results of the model validation using the actual time study data provided by an open pit mine operator near Tucson, Arizona, are also described in this paper.

Jan 1, 1978

By David L. Giles

The alkalic igneous province of Montana consists of centers of laccolithic and stock-like intrusive complexes with associated sills, dikes, and breccia pipes (e.g., Judith, Highwood, Little Belt Mts.); isolated plug-like mafic bodies (e.g., Smokey and Eagle Buttes); and clusters of kimberlitic diatremes and ultrabasic dike swarms (Missouri River Breaks). The province extends in a belt throughout central Montana from the North Absaroka Range in the south to the Sweetgrass Hills on the Canadian border. Intrusive activity ranged in age from Late Cretaceous to late Miocene, peaking at about 50 m.y, ago. Diverse types of significant epithermal gold mineralization occur at many of the laccolithic centers. This mineralization took place in large part during the waning stages of, or following, igneous activity. Large remnant travertine blankets in the region attest to comparatively recent hydrothermal activity. The quartz-pyrite-gold mineralization ranges from igneous- hosted stockworks or fracture sets (Zortman-Landusky and Neihart districts) and breccia pipes (North Moccasin Mts.) to replacement zones in flanking and upwarped Madison Group limestone (Gilt Edge and Kendall districts). The latter are mostly localized by intraformational solution breccias in the upper Madison, notably near porphyry contacts. Gold mineralization in the province was accompanied by varying amounts of silver, base metals, sulfosalts, and tellurides, with quartz, fluorite, carbonate, and barite and gangue. Gold occurs as auriferous pyrite, sylvanite, or in native form. Since the 1880's, primary gold production from numerous scattered deposits in the Judith, Moccasin, and Little Rocky Mountains, along with byproduct gold from the Neihart silver district (Little Belt Mountain), has totalled around 2 million oz. The major deposits were in the 1-2 million ton range at an average gold tenor of 0.3-0.6 oz per ton. Most of the ore was mixed oxide or carbonaceous sulfide ore and was treated either by amalgamation or by roasting-cyanidation. Current activity includes heap-leach operations on bulk- tonnage low-grade (approximately 0.03 oz per ton) ores at Zortman-Landusky, and several small-scale, experimental leach or mining operations on carbonaceous replacement ores, as in the Kendall district and Spotted Horse mine. Current exploration efforts for gold are focused not only in the old established districts, but also in and around other alkalic centers, which have been unproductive to date, such as the Crazy Mountains, Sweetgrass Hills, and Bearpaw Mountains. Target concepts in these efforts are porphyry-hosted stockwork or disseminated gold ores and Carlin-type replacement lodes in the flanking Madison or other favorable carbonate units.

Jan 1, 2013

By J. M. Wempen, M. K. McCarter

"Differential Interferometric Synthetic Aperture Radar (DInSAR) is a satellite-based remote sensing technique capable of measuring centimeter-level surface displacement with high spatial resolution over large areas. Regular monitoring of subsidence due to underground mine development is one potential application of DInSAR, and in this study, the application of DInSAR for subsidence monitoring is evaluated for two mining regions in the mountain west of the United States. In general, DInSAR has potential to identify the shape and extent of subsidence; in some cases, magnitudes and rates of subsidence can be defined. Importantly, the effectiveness of DInSAR for subsidence monitoring depends on the radar band (wavelength), the subsidence rate and the time between image acquisitions, and the topographic and vegetative surface characteristics. INTRODUCTION Differential Interferometric Synthetic Aperture Radar (DInSAR) is a satellite-based remote technique that can be used to measure small surface displacements. Under good conditions, centimeter-level displacements can be measured with subcentimeter accuracy (Buckley, 2000; Massonnet and Feigl, 1998). Additionally, DInSAR data have relatively high spatial and temporal resolutions. Pixels in Synthetic Aperture Radar (SAR) images can have a ground resolution as small as about 3 m, and images often include tens to hundreds of thousands of pixels and cover tens of kilometers. Regions are imaged regularly, and periods between images typically range from weeks to months. In DInSAR, phase measurements from two radar images acquired over the same region at different times are used to precisely measure relative distances (Rosen, 2014). Surface deformation, topography, and changes in the satellite position all contribute to differences in the length of the path that the radar wave travels in each image. SAR sensors use radar with relatively long wavelengths; L-band (24 cm wavelength), C-band (6 cm wavelength), and X-band (3 cm wavelength) radar are used most commonly. Because the wavelengths are long, small changes in the path length of the radar signal can be quantified by measuring the change in the phase of the radar signal between the images. In general, changes in the path length due to changes in the satellite position and topography are known or can be estimated, and centimeter-level changes in the path length due to deformation are measurable. This study evaluates the effectiveness of DInSAR for measuring subsidence in two mining regions in the mountain west of the United States. L-band data from the Advanced Land Observing Satellite (ALOS) and X-band data from the TerraSAR-X mission are evaluated. Imaging characteristics, including the radar band and the time between image acquisitions, are important for effective subsidence monitoring."

Jan 1, 2017

By Ralph Spickermann

UK Seabed Resources (UKSR) signed a manganese nodule exploration contract with the International Seabed Authority on 8 February 2013 for a 58,000 km2 tract on the eastern edge of the Clarion Clipperton Zone (CCZ). UKSR is a private company based in the United Kingdom and established primarily to develop the commercial potential of the CCZ deposits. This is the first of many anticipated regulatory, market and technical milestones that are requisite for (1) environmentally responsible commercial scale production of nodule derived metals and (2) generation of revenue through their sale in the global commodities market. This presentation will describe the progress made to date in this effort and an industry-based perspective on the tasks and challenges that may lie ahead.

Sep 1, 2014

By R. H. Bartlett

Hydrometallurgical processes for copper flotation concentrates avoid the S02 emission problems associated with smelting, but they require oxidation of copper to obtain solubilization during leaching. The resulting copper ions must be reduced to metal, which normally requires large amounts of energy or energy equivalent reagents such as hydrogen or iron. The conventional reduction method is electrowinning which is labor intensive and involves 35 to 40% of both the en-tire operating and capital cost of the better hydrometallurgical processes. Smeltermen are correct in criticizing the available hydrometallurgical processes for being more energy intensive than modern smelting processes. Clearly, there is considerable incentive to reduce the cost and energy required for reducing copper ions from solution. Furthermore, it is thermodynamically possible to do this using sulfur contained in the concentrate itself. In fact, the thermodynamic potential of oxidizing sulfur from S+4 to the S+6 state is greater than required to reduce cupric ion to metallic copper. (1) Realization of this potential in a practical process would significantly reduce the cost of hydrometallurgical processing of sulfide concentrates because sulfur would become a cost-free reducing agent. An apparently practical method is to use SO3 and HSO3 ions, obtained by ammonia scrubbing of SO2 from a concentrate roaster gas, to reduce leached copper to metal in an autoclave. This reduction step is the Jumau 1907 patent. (2) A series of steps including sulfite reduction constituting a crude flowsheet was suggested by Parker in 1976(3), but apparently little development work has been done by him, since he has been interested in new routes of refining the resulting copper powder. The purposes of the present paper are to elaborate on the Jumau-Parker thrust. Describe a detailed complete sulfite process flowsheet based on materials and energy balances, discuss the chemistry, and discuss further work that is required to develop this process. The results of the present paper are largely based on a synthesis of the steps using handbook chemistry. Process materials, utilities costs, and energy requirements are projected to be unusually low.

Jan 1, 1978

By R. Elias

Botswana is a mining-dominated sub-Saharan country. Workforces are characterised by poorly educated operators and front line supervisors, with equipment and management to 1st World standards. Poor communication, ignorance of business objectives, inability to meet targets, and lack of problem-solving capacity are the norm. Training leads to high expectations and is of concern to management as a source of dissatisfaction, despite the long-term benefits higher skills have for mine viability. The aims of a technical training programme are presented with various models and approaches being implemented at operations in Botswana. These are used to construct a series of guidelines for technical training initiatives.

Jan 1, 2000

By P. Zhang, S. Al-Thyabat

"Phosphate rock contains traces of rare earth elements (REEs) and can be a secondary source of these critical materials as large tonnages of phosphate rock are mined annually. Attention has mostly focused on the extraction of REEs from phosphogypsum, which contains more than 70 percent of the REEs reporting to phosphate concentrate, with only limited work conducted on REE extraction from sand tailings and slime even though they account for 16 percent and 15 percent, respectively, of REEs mined with phosphate matrix.In this work, phosphate flotation tailings were upgraded by gravity separation and froth flotation. Gravity separation was conducted using a laboratory shaking table, while flotation was conducted in a Denver D-12 flotation cell. The concentrated tailings were then leached by nitric acid followed by REE extraction with solvent and ion-exchange resin.The sand tailings were assayed as having 2.6 percent phosphate (P2O5 ) and 198.1 µg/g REEs. It was found that the shaking table could produce tailing concentrate assayed as having 8.6 percent P2O5 and 616 µg/g REEs but with only 20 percent REE recovery, while the froth flotation produced froth concentrate assayed as having 8.1 percent P2O5 and 368.2 µg/g REEs with 63.5 percent REE recovery. Leaching the flotation concentrate with 5.2 M (25 percent) nitric acid followed by extraction with solvent and ion-exchange resin yielded precipitates with REE contents of 0.926 and 0.314 percent, respectively, compared with 0.716 and 0.213 percent when table concentrate was used.IntroductionRare earth elements (REEs) consist of a group of 17 elements: the 15 lanthanides along with yttrium (Y) and scandium (Sc). They are rare not because of their scarcity in the Earth’s crust but because they are rarely found in economic and mineable deposits. REEs are called “seeds of technology” because of their importance to some critical technological industries such as renewable energy, hybrid cars, electronics and batteries. On average, an electric car or a hybrid car contains about 10 kg of REEs (Grasso, 2012; Radhika et al., 2011).REEs are usually categorized into light (LREE) and heavy (HREE). LREEs consist of lanthanum (La), cerium (Ce), praseodymium (Pr), neodymium (Nd), promethium (Pr), samarium (Sm), europium (Eu), gadolinium (Gd) and scandium (Sc), while HREEs consist of terbium (Tb), dysprosium (Dy), holmium (Ho), erbium (Er), thulium (Tm), ytterbium (Yb), lutetium (Lu) and yttrium (Y). About 200 minerals contain traces of REEs, but only three are considered economically significant: bastnasite, with the formula La,Ce(CO3)F; monazite, with the formula(Ce,La,Nd,Th)PO4; and xenotime, with the formulaYPO4 (Jordens, Cheng and Waters, 2013)."

Jan 1, 2016

By B. L. Bobo

To ensure the continued growth and economic viability of the Western coal industry, both in the domestic and inter- national markets, it is essential for the industry to become more creative and active in confronting the most serious obstacle in this objective; and that is, the inherently long distances which Western coal must be transported inland to reach its major markets. Figure 1 shows the 1982 coal consumption by state for those states where Western coal was consumed. (Except as noted in this paper, Western coal producing states are defined as Colorado, New Mexico, Arizona, Utah, Wyoming, Montana and North Dakota. Any exceptions used will have only an insignificant effect on the content of the paper). This figure illustrates the long distances that are required for Western coal to reach its markets. The total production for 1982 from the Western coal producing states was approximately 220 million tons, of which only 85 million tons was consumed within the boundaries of these states. The remainder was transported to markets outside the area. This map also shows, based strictly on the consumption of the states to which Western coal was shipped during 1982 and not considering other factors which are involved in the marketing of coal, the total market potential of Western coal would amount to a total of 445 million tons. This does not include export coal from the West Coast, which is now estimated to be less than 2 million tons for 1983. In 1980, it had been estimated that by 1985 the West Coast exports would have been at least 10 million tons per year, which will not be attained.

Jan 1, 1983

By E. McCarthy

"INTRODUCTION Talc is a hydrous magnesium silicate with the approximate elemental composition 4MgO.3SiO2.H2O. It is one of the layered phyllosilicates (like kaolin and mica) but it differs from these in that it is relatively hydrophobic. This is due to its unique crystalline structure whereby a brucite inner layer is sandwiched between silica layers and the adjacent silica layers have no interlayer bonding other than van der Waals forces. This allows talc to be sheared easily along this basal plane, and the surface is covalent not ionic. Talc occurs both as a relatively pure material (>90% talc content) and in conjunction with many other minerals in proportions all the way from 1% to 90%. At lower concentrations, it is often considered a nuisance mineral when it occurs with base metals like copper, molybdenum or nickel or with precious metals like platinum or palladium. It floats readily with these materials and often is suppressed using guar gum or carboxy methyl cellulose which will absorb along the basal surface and make it hydrophilic. Alternately if the reduced ore is hydrophobic, like MoS2, then a partial oxidation of the sulfide will convert the surface to a hydrophilic oxide and the talc can be floated away in a separate step. Talc in grades from 20 to 90% has been commercially exploited in a wide range of pigment (paint and paper), material (ceramic, construction and cosmetic), reinforcing (polymers and composites) and functional (pitch adsorbent, lubricating agent) applications. Initially these tended to be local or regional markets, but eventually with certain higher purity grades, cosmetic, polymer and ceramic applications became valuable enough to be national and trans ocean markets. TALC FLOATATION PLANTS This drove the need for higher purity grades of talc and initially this need was met primarily by ore sorting. This works well for certain deposits with well crystallized talc lenses, but for ores, such as those from widely available ultramafic deposits, where the liberation size is closer to 100 microns, sorting is not effective. That drove the need for floatation and the first investigations were published by Clemmer and Cooke of the US Bureau of Mines in 19362. The first commercial floatation plant was installed in Johnson, VT by the Eastern Magnesia Talc Co in 1937. The circuit is shown in the schematic (Figure 1). The ore was an ultramafic, serpentine derived talc; mineralogy was about 55% talc, 40% ferroan magnesite and 5% oxides, sulfides and other silicates. The oxides include hematite and chromite, sulfides pyrite and gerstorffite and silicates chlorite, serpentine and mica. After crushing, the ore was dry ball milled and then air classified to remove minus 325 mesh fines. The coarse fraction was further classified to cut at about 100 mesh and the fines from this were the feed to floatation. The -325 mesh (about 15% of the ore) was sold as a paint grade and the plus 100 mesh (about 25% of the ore) was screened to make an asphalt backsurfacing grade."

Jan 1, 2018

By Nora M. Hutt, Kevin A. Morin

Geochemical static tests are a basic component of geochemical assessments and predictions for acidic drainage, and include acid-base accounting and total-metal contents. A key database for such information is the International Static Database (ISD), which currently contains more than 45,000 static-test analyses from over 200 minesites. Such large databases are useful in identifying general trends and, just as important, the percentage of exceptions. General trends and significant exceptions can be seen in the ISD by comparing one parameter against another. This paper shows that bulk neutralization potential (bulk NP) obtained from acid titration is often a good indicator of neutralizing capacity above values of 10 t CaCO3/1000 t. Other types of calculated neutralizing capacity are then compared to bulk NP to determine if they, in fact, reliably represent actual neutralizing capacity and if they can substitute for the more time-consuming and expensive bulk NP. For example, bulk NP correlates better with Carbonate NP (from carbonate analyses) and Total-carbon NP (from total-carbon analyses) than with (Ca+Mg) CaNP (from solid-phase analyses of calcium and magnesium). This means that, in general, (Ca+Mg) CaNP is a less accurate substitute for bulk NP than the other types, and thus requires intensive site-specific justification if a substitution is attempted. This also means that measurement of the frequently less-expensive parameters of total carbon and carbonate can often substitute, within site-specific error bars, for the bulk-NP titration. However, the ISD also shows that non-carbonate minerals make the primary contribution to neutralization in up to 20% of samples, so Carbonate CaNP and Total-carbon CaNP do not always reveal the full neutralizing capacity of a sample.

Jan 1, 2000

By Jr. Smith

Industrial minerals are just other rocks, except for the unique characteristics that make them useful in an industrial process. There is not a ready market for this type mineral and one or more uses must be developed to sustain production. The name "olivine" is a generic term used to indicate a group of orthosilicate minerals in a solid solution series, with forsterite (Mg2SiO4) and fayalite (Fe2SiO4) as endpoints. Since neither is found alone in nature, the mineral is always a combination of the two. The commercial deposits are high in magnesium and on the high end of the melting scale in the series. The name comes from the olive-green color.

Jan 1, 1992

By K. Ananthpadmanabhan

Hydrolyzable surfactants such as fatty acids and amines undergo, in addition to micellisation and precipitation, various associative interactions in aqueous solutions to form ion molecular complexes such as acid-soap, dimers etc. depending upon the solution conditions such as pH. The interaction of these collector species with the mineral surface and with other dissolved species in solution will play a significant role in determining the interfacial processes such as adsorption and flotation. Marked differences in the hydrophobicity imparted to the mineral surface depending upon the solution conditions such as Ph can be attributed to possible differences in surface activities of the above complexes. This aspect of solution chemistry of flotation systems is discussed here for two widely used collectors namely, oleic acid and dodecylamine. Equilibrium species distribution diagrams based on the available literature .data and on estimates of energy of interactions between molecules, have been obtained for oleic acid and dodecylamine solutions.

Jan 1, 1978

By Derek J. Penrice

A critical element of the Transbay Transit Center Program, the Caltrain Downtown Extension (DTX) will extend commuter rail service into downtown San Francisco and accommodate future statewide high-speed rail service. The DTX project includes 1.8 miles of underground construction, comprising significant sections of mined and cut-and-cover tunnel. At the request of stakeholders, an updated cost estimate was prepared early in the project?s preliminary engineering phase. Unsurprisingly, this yielded a cost substantially higher than the available budget. This paper provides a summary of the management processes and planning decisions taken to bring the project back to budget, resulting in a configuration which derives maximum value from available funding and retains maximum flexibility for future system expansion.

Jan 1, 2008

By H. Huang, R. N. Gow

"In Part I, Gibbs’ phase rule was applied to mass-balanced EH-pH diagrams for the Cu-As-S-H2O system. The diagrams were generated using the stoichiometry of enargite as a basis. In this study, the calculations were expanded to cover the stoichiometries of three other Cu-As-S minerals – tennantite, sinnerite and lautite – and compared with enargite. Stability regions within the resulting EH-pH diagrams were found to change with stoichiometry such that a particular mineral would predominate if its stoichiometry was used in the calculation. Solution speciation was also found to vary, with thioarsenate being the best example. This stoichiometric effect helps to explain results reported in the literature and would be difficult to realize if it were not for mass-balanced calculations. IntroductionA comprehensive thermodynamic review has been conducted on the aqueous copper-arsenic-sulfur (Cu- As-S) system (Gow et al., 2014, 2015a, 2016b; Gow, Huang and Young, 2016c). Data on the free energies of more than 100 species were collected from various authors, and thermodynamic databases collated to produce mass-balanced EH-pH diagrams using the thermodynamic equilibrium calculation software STABCAL (Huang, 2014). The full database is listed and discussed in Gow et al. (2015a). Diagrams were generated for enargite and confirmed with Raman spectroscopy using bulk mineral electrodes in order to identify reactions spectroelectrochemically. Theoretical calculations agreed well with the experimental results under alkaline conditions (Gow et al., 2015a), acid conditions (Gow et al., 2014) and alkaline sulfide leaching conditions (Gow et al., 2015b).In the present study, additional mass-balanced EH-pH diagrams were generated by changing the Cu-As-S stoichiometry from enargite (Cu3AsS4) to tennantite (Cu12As4S13), sinnerite (Cu6As4S9) and lautite (CuAsS). Regions for the thermodynamically stable species were shown to change with the four different mineral compositions. Potential leach conditions, both for co-dissolution and selective dissolution techniques, were examined for differences in predominant species according to changing copper-to-arsenic ratios, sulfur compositions and sulfur oxidation states."

Jan 1, 2016

By J. M. Wempen

As development in underground coal mines progresses away from the critical components of the ventilation system, including the main fans and ventilation shafts, resistance is markedly increased. This results in higher pressure and flow requirements from the main fan(s) to maintain adequate face ventilation, which often requires that the primary ventilation system is upgraded with additional shafts and surface fans. The use of booster fans underground is a potentially practical alternative. This study presents simulations of the use of booster fans in two underground ventilation scenarios, one longwall and one room and pillar. The booster fan effects on the power requirements of the ventilation systems are evaluated.

Jan 1, 2011

By Hélio Blak

The Paranapanema Group was created in February 1996 when a group formed by the Brazilian pension funds acquired four companies dealing with nonferrous metals. The new Paranapanema Group, basically related to the tin and construction business, became the sole Brazilian primary copper producer, the second zinc producer and one of the most important producers of copper products, mainly tubes and fittings. To put together such different companies, managed before by family groups and with different cultures and principles, was and still is a big challenge. The strategy of developing and consolidating it as an homogeneous group is based in three pillars: an increase in production, quality and technological improvements on products and market mix and a permanent cost reduction program, using all the potential synergies founded.

Jan 1, 1998

By J. Drelich

The highly-efficient and economically-feasible technology for bitumen recovery from US oil sands using a water extraction approach was developed at the end of the last century. This water-based bitumen extraction process has been optimized based on observations and analysis of microscopic mechanisms of bitumen release from oil sands and the bitumen transfer to a froth product as well as measurements of interfacial properties of bitumen. The wetting mechanisms that occur in the diluent-assisted water-based processing of US oil sands include bitumen film rupture and recession on sand grains and bitumen transfer to nucleated and injected gas bubbles. These mechanisms are reviewed in this contribution.

Jan 1, 2007