Search Documents

By Zhenqi Cai, Mike Lichte, Kimberly Kennedy

The Ohio River Tunnel is the first of three combined sewer overflow tunnels to be constructed under Allegheny County Sanitary Authority's Clean Water Plan. The project consists of a total of approximately 5.5 miles of 18-ft and 14-ft finished diameter, segmentally lined deep rock tunnels and smaller diameter dewater and flow connector tunnels, as well as 8 deep flow drop and access shafts varying from 25-ft to 70-ft in finished diameter and 130-ft to 170-ft in depth. This paper describes the project components and the primary engineering challenges faced during design, including tunnel alignments and shaft site optimization with tight right-of-way constraints and multiple railroad and highway crossings. Assessment of tunneling methodology as well as tunnel and shaft designs and constructability included overcoming 5-bar hydrostatic pressure, abrasive bedrock, and the selection of the appropriate support of excavation systems in high-permeability alluvial soils adjacent to the Ohio River.

Jun 23, 2024

By Dan Nilsson

Open pit mining is the strong sector of the American mining industry. In the middle of the 60's. 17-18% of the ore in metal mines was mined with underground methods. From the middle of the 60's to 1980 the production in open pit metallic mines increased from about 400 to close to 600 million short tons while at the same time the underground mine production decreased a little, from about 90 to about 80 million tons. Less than 15% of the ore prodction now come from underground mines. Large amounts of waste rock were also handled in the open pits. In the middle of the 60's about 600 milion tons were handled, in 1980 1,200 million tons were moved. This means that the average stripping ratio increased from about 1.5 to over 2.0 tons of waste rock per ton of ore, figure 1.

Jan 1, 1983

By David Wright, Colin Burns

Successful leaching of gold depends on appropriate chemical conditions; contact between leach solution and the gold particles; separation of the leach solution from the solids and extraction of the valuable ion from the solution. Irrespective of the leaching method employed the chemical conditions required are similar as is the dependence of solu­tion/gold contact on liberation. The various leaching methods available vary in the means by which gold/solution contact and solid/liquid separation are achieved. The essential difference between heap or vat leaching techniques and those involving agitation of a slurry is dependence on percolation for effective gold/solution contact. The most significant factor preventing uniform percolation is the presence of fines or clays. The quantity and character of the fines fraction is ore type dependent and may result from crushing, degradation during stacking or leaching, or the natural size distribution of the ore. The problems associated with fines can be aggravated during stacking and preparation of the heap. Segregation during stacking can result in concentration of fine particles at the centre of heaps. Further concentration of fines may also occur during irrigation by the movement of the fine particles with the solution. The end result is that the areas in which fines are concentrated become areas of low permeability. The contact between leach solution and the ore in such areas is, at best, slowed down dramatically and, in some cases, prevented altogether. The consequences of this phenomena are slow leaching and a reduction in recovery. The conventional solution to this problem is well known. Agglomeration of ore prior to heap leaching is practised widely. The effect of agglomeration is to immobilise the fines by causing them to adhere either to each other or to larger ore particles. The net effect is that the ore behaves as if no fines were present. The use of agglomeration is limited only by its cost, the most significant components of which are the cost of binding agent, commonly cement, and the capital cost of the agglomerating equipment.

Jan 1, 1995

By Bobby G. Cahoon

The ( ) Tayaaja ( ) . The deposit ( ) 130 kilometers due east of the continental divide and approximately 290 kilometers east-southeast of Lima (Figure 1). Relief in the immediate vicinity of the mine, which lies or the west side of the Mantaro river, is in excess of 2,000 meters, and the elevation varies from a low of 2,000 meters above sea level on the Mantaro River to a high of 4,386 meters at point T-27 (Figure 2). Although the Cobriza deposit was first reported by the Italian Geographer Antonio Raimondi in 1866, only three reports have been published on the deposit, which began production in 1966 (Duefias, 1908; Fernandez Concha and Garcia y Garcia, 1961; Petersen. 1965). Many private reports have, however, been written by geologists employed by the Cerro de Pasco Corporation. These reports and the author's observations, while employed as the Cobriza Division Mine Geologists form the basis of the present paper, which describes the relations between-the ore controls in the Cobriza mine and the regional and local structure.

Jan 1, 1971

By R. V. Ramani

An improved mine environment is the single most critical factor affecting the health and safety of workers engaged in underground coal winning. A very important subclassification of this wide field is mine ventilation, which essentially deals with 'mine atmospheric environmental control.' To ensure proper mine atmospheric environmental control, adequate quantities of air must flow through working sections in the mine. In recent years much attention has been paid to the fan and its prime movers, but the efficient use of the fan output in the workings has not received an equal amount of investigation. In mechanically ventilated mines friction losses in main airways often account for 70 to 90 percent of the total pressure loss sustained in the system. Also the leakage losses are a serious detriment to the efficiency of mine ventilation systems. It is not uncommon to loose 60 to 70 percent of the air between the fan and the last open cross-cuts due to leakage directly into the return Proper assessment of these losses in simulating and projecting complex ventilation systems is vital. Network analysis of ventilation systems is not new. Scott and Hinsly (1951) presented the detailed mathematical framework. Since then work has been done in adopting this technique to analog, and within the past few years, to digital computers. Development of computer programs to solve ventilation network problems has been reported in United Kingdom, Japan, U.S.S.R., South Africa, Germany, and the United States. The purpose of these programs is to serve as an experimental mine wherein analysis of proposed alternatives or ventilation planning can be tested. The great power of the computer as a planning tool lies in the ability to input empirical or Projected data into programs with predicting ability. But, however good a computer program is, unless fairly accurate input information is available accurately assessing the engineering factors of the ventilation system, the output will be suspect. Thus, to simulate and project mine ventilation systems, good estimates of leakage and friction factors are important. Yet, relatively little work has been done in the past three decades to determine these more realistically.

Jan 1, 1973

By C. D. Kuchera

Ore crushing facilities at the Phelps Dodge Morenci Reduction Works became operational in January of 1942. This plant, with a capacity of 25,000 tons per day, was part of a project started some five years earlier with development of the Morenci Open Pit Copper Mine. In the following year, World War II's heavy copper demands prompted an 80% expansion in concentrating capacity to 45,000 tons per day resulting in a doubling of the secondary crushing plant. In the late 1950s and early 1960s, grinding capacity was again expanded to the present 60,000 TPD. This time the then 20 year old crushing plant was obliged to meet a 20% increase in production demand with no additional equipment. The ore, principally a medium hard monzonite porphyry, is dumped from 40 yard rail cars into an ore pocket over the primary crusher at a rate of approximately one car per minute. The primary crushing flowsheet, Figure 1, has remained essentially unchanged over the years. Equipment consists of a 40 by 16 foot grizzly set on a 40° incline and having 6" openings, a 60" gyratory crusher nomin¬ally set at 62" + 1" on the closed side and two 72" by 38' panfeeders which load crushed ore and grizzly undersize at a rate of 4,000 tons per hour onto a twin 54" belt conveyor system for delivery to the coarse ore bin. Ore is distributed across the bin by two single side discharge tripper cars. Bin capacity is extremely limited at 23,000 tons of which only 12,000 is available or "live".

Jan 1, 1975

By F. G. Crack

This paper is based on the philosophy that the management structure and strategy required for mine construction and development projects are different from that required for routine production and maintenance operations in a mine. The purpose of this paper is to present an integrated approach to the management of mine development projects. This paper highlights the four major aspects of the integrated approach. First, a brief review of the various types of contract documents is provided. Second, the management organization of a project is discussed. Third, the project manager's role and the field supervisor's responsibility are briefly outlined. Finally, the use of scientific techniques for planning, scheduling, executing, and controlling projects is presented. Each of these aspects is important; however, each by itself cannot be expected to bring order or unifying impact to the complexities involved in overall project management. When all these aspects are coordinated, the result will be a sore successful project from conception to completion.

Jan 1, 1982

By J. J. Antony

The Cactus Gold Mine is a joint venture comprised of Middle Buttes Partners Ltd. (CoCa Mines, Inc.--operator, T. Congdon and W. Carey) and Compass Mining, Inc. The project includes 2.4 sq. miles of contiguous mining claims and leases in the Mojave Mining District, Kern County, California, approximately B5 miles northeast of Los Angeles. The property is readily accessible year round by all-weather roads and is within 6 miles of the main line of the Southern Pacific Railway.

Jan 1, 1988

By Nikhil Dhawan, SHAILA MIR

Consumer preference for ever-higher laptop performance coupled with laptops’ declining lifespans make them a significant contributor to electronic waste. An in-depth evaluation of elemental composition and distribution is important for determining metal recovery potential and sustainable recovery processes. In this work, the characterization of individual components of laptops is studied for the systematic identification of important elements and for streamlined and structured recycling, to reduce processing steps and improve economics. A process flowsheet highlighting various recycling routes by targeting metals and various components is also proposed.

By Randall Smith, Leslie Stayner

At the request of the Mine Safety and Health Administration, a quantitative assessment of the risk of lung cancer associated with occupational exposures to diesel exhaust was performed. This assessment was primarily based upon the results from a study of the effects of chronic inhalation exposure to diesel exhaust in Fischer-344 rats (previously reported by Mauderly et al., 1987). An adaptation of the Armitage-Doll multistage model, which allows for an age-dependent effect of exposure, was used to model the tumor response data. This model was fitted to all tumors (benign and malignant), and to malignant neoplasms alone. Estimates of unit risk (potency) were derived based upon a linear approximation to the results from the multistage model. A biologically equivalent dose was developed to scale the results from airborne exposure in rats to humans, which was adjusted for differences in weight, ventilation rate, deposition fraction, and the percentage of time actually exposed. Comparisons are made with risk estimates derived from modeling other rat inhalation bioassays and from applying different models to the study by Mauderly et al. (1987). We emphasize that our risk estimates are based upon a series of assumptions and carry a great deal of uncertainty. In particular, uncertainties regarding the effects of exposure on lung clearance mechanisms, the deposition rates in humans, and the relevance of our exposure index limit our confidence in these risk estimates. Because of these uncertainties, this risk assessment would best be viewed as an exploratory effort. Key words: Diesel, lung cancer, risk assessment

Jan 1, 1991

By A. K. Bakshi

Mineral suspensions show Newtonian flow properties at lower solid concentration, but change into non-Newtonian regime as the solids content is increased. For Newtonian fluids viscosity is independent of shear rate, but for non-Newtonian fluids it varies with rate of shear. Therefore, measurement of viscosity at a shear rate, different from the process will be futile unless the slurry is Newtonian. This is especially true for hydrocyclone operation, where the rate of shear is different at different points within the hydrocyclone. In this case, it is very important to determine the flow type of the suspension before attempting to establish any correlation between viscosity and process efficiency. A new technique to distinguish such changes in flow type has been developed. This involved a co-axial cylinder type viscometer which measured apparent viscosity at a low shear rate, and a vibrating sphere type viscometer which measured the apparent viscosity at a high shear rate. Special precautions were taken to allow measurements of viscosity of rapidly settling mineral suspensions. Because the vibrating sphere viscometer operated at a much higher shear rate than the rotating viscometer, the two instruments together could determine the shear-rate dependency of the viscosity. Ground silica of 80% passing 65~m size in water was used to prepare slurries at concentrations ranging from 1O-70wt% solids. Viscosity of each slurry sample was measured simultaneously by both the viscometers and the results were compared with each other. With this technique, it was found that all the silica slurry samples were in the Newtonian flow regime.

Jan 1, 1995

By A. K. Bakshi

Slurry rheology affects autogenous grinding performance by changing the rock's breakage characteristics. In this study pilot scale batch autogenous grinding was carried out to observe the effect of viscosity on the breakage characteristics of the rocks (the media), and on the overall specific energy consumption. Clay/fines content, and temperature of the initial charge, were varied to alter the viscosity of the slurry. Results showed that at higher slurry viscosity, rocks became more difficult to break, resulting in an overall increase in the specific energy consumption of the mill. Also, it was observed that viscosity had a significant effect on the amount of critical size material present in the grinding circuit, where the critical size material is the material which is too large to be effectively ground in the mill, and too fine to act as grinding media.

Jan 1, 1996

By Jeffrey P. Carstens

INTRODUCTION Thermally induced fracture of rock is one of the oldest rock breakage techniques known to man. Primitive underground miners used fires to heat and crack rocks as early as the third century B.C. (Ref. 1). History aside, however, present-day tunneling and mining interests are reconsidering the use of modern heating units for rock fracture for some very good reasons. One of the most important advantages of many heating techniques is the lack of direct contact between the heating device and the rock. This means a lower wear rate relative to mechanical cutters, and no large reactant force to be supplied by the tunneling machine. In addition to avoiding physical contact, some heating systems (e.g., electron-beam guns and lasers) can deliver energy to a rock face much more intensely than can be conveniently handled mechanically. Thus, heating power densities of the order of lob to 107 watts/in.2 and greater can be achieved with high-power lasers. These high power levels allow much higher instantaneous penetration rates than can be achieved by mechanical cutting. Another advantage that accrues to some thermal techniques, such as, for example, surface spalling, is that the thermal fracture process works particularly well in certain rock types (e.g., granite) that are particularly hard to cut mechanically. Other methods, involving high power density, are able to cut any rock type, and are relatively

Jan 1, 1997

By Ray E. Harris

New developments have occurred in Wyoming's industrial minerals industry since the 32nd Forum on the Geology of Industrial Minerals in Laramie, Wyoming in 1996. The soda ash trona and bentonite industries have experienced overall growth. Gypsum and limestone production have remained constant, but have the potential for dramatic growth. The mining of zeolite ceased in 1997. The struggling dimension stone industry has increased production, but development has lagged behind the schedule predicted in 1996. The construction of a container glass plant and associated production of glass raw materials, as predicted in 1996 and imminent in 1998, is now on hold due to unforeseen market factors. Increases in railroad and highway construction have, and will, greatly increase the production of construction aggregate for local uses. An iron carbide industry, not foreseen in 1996, is in the planning stages.

Jan 1, 2001

By J. Pang

The mechanisms of chalcopyrite oxidation in alkaline solutions have been studied using cyclic voltammetry and AC impedance spectroscopy techniques. Analysis of the impedance spectra using equivalent circuit models has made it possible to suggest layerwise growth of surface films. From the value of equivalent circuit parameters, properties of the surface layers are inferred. These properties change substantially with the change in oxygen and/or collector concentration in solution and give rise to changes In contact angle and flotation response. In agreement with prior investigations, the present study shows that flotation recoveries alone cannot be used to determine the effect of collector on flotation of chalcopyrite. The rate of flotation is a more sensitive parameter to determine the role of collector on floatability of chalcopyrite.

Jan 1, 1989

By W. E. Benton

Diatomite or diatomaceous earth is a siliceous sedimentary rock principally made up of the skeletal remains of the diatom, a microscopic, single-cell aquatic plant related to algae. The unique structure, chemical stability and physical properties are the major attributes of diatomite not met by other forms of silica. The production of diatomite was down in 1982 vs. 1981, reflecting the worldwide recession. The principal markets for diatomite products continue to be basically filtration and fillers. The outlook is for small but steady growth into the 1990s.

Jan 1, 1983

By Paul Russell, M. M. Kimberley, Erick F. Welland, Louis Cope, C. C. Mosher, William M. Shepard, William C. Larson, Graham Closs

Exploration activities in 1980 felt the effects of unstable economic conditions and oscillating metal prices. In the cyclical, boom-or-bust precious metals and uranium markets, precious metals activity flourished and uranium was definitely in a slump. By November last year, the price for vellowcake was down nearly $20 from two years earlier. Many mining and milling operations closed, particularly in Wyoming, New Mexico, and Colorado. Decreasing emphasis on nuclear power continued to impact the market, as did the Three Mile Island accident of 1979. Earlier forecasts estimated that 10 to 12 reactors would be ordered per year by US utilities throughout the 1980s, but current forecasts suggest that it may be 1983 or 1984, or even later, before any new US plants are ordered, according to Thomas A. Boyden, vice president of Nuclear Exchange Corp. "Without those new plants, the consumption loss to industry is 4 to 5 million pounds (1.8-2.3 kt) of uranium per year. The cumulative loss to the industry is currently estimated at 25 to 30 million pounds (11.3-13.6 kt)," Boyden said in a May 1980 presenta¬tion. Despite the plunging market, there were a few notable uranium explora¬tion programs: •Exxon expanded uranium exploration in New Mexico, where the company reportedly took preliminary steps toward acquiring mineral rights to a 22-km2 prospect, 19 km south of Santa Fe. • Mountain States Resources began the second phase of an exploratory drilling program on its Sinbad/ Solo prospect in Utah. • Also in Utah, Cotter Corp. drilled its first exploratory hole in the Dirty Devil River district. Exploration for precious metals in 1980, however, appeared to tend toward the opposite extreme. High prices sparked near feverish searches in Alaska, California, Colorado, and Nevada. Numerous mines abandoned years ago were revived with some signs of success. Significant gold finds were reported in California and Nevada: • Homestake Mining Co. announced a gold discovery in California estimated to contain over 5 Mt with an average grade of about 5.8 g/t. Because the deposit consists of finely disseminated particles not visible to the eye, many speculate that prospectors bypassed the area during the 1849 California gold rush. • Newmont Mining Corp. discovered two gold ore bodies-Maggie Creek and Gold Quarry. Maggie Creek reportedly contains an estimated 13.7 t of gold in 4.3 Mt of ore, and Gold Quarry contains about 31.1 t of gold in 9 Mt of low grade ore and 2.3 Mt of higher grade ore. Highlights of this year's exploration review include articles on the modest growth recorded in geophysical activity, technical developments in exploration geochemistry, the variety of new instruments being tested or made available for exploration, and a state-by-state exploration review for the year.

Jan 5, 1981

By Joseph Peterson, Alexander May

The Bureau of Mines used geochemical modelling computer programs to characterize a site containing lead slag generated by a lead processing facility. Tests for toxic elements by the U. S. Environmental Protection Agency (EPA) extraction procedure showed that all elements except lead were in compliance. Concentrations for lead ranged from 28 to 30 ppm. However, analysis of water samples from monitoring wells resulted in no lead concentrations that exceeded the National Drinking Water Standard. A discussion of a computational program to calculate concentrations of lead species and several other ions is presented.

Jan 1, 1991

By A. W. Khair

In 1985, an extensive longwall mining research project was initiated by the West Virginia University Research Center entitled "An Improved Longwall Mining Technique" with the purpose of providing operational guidelines for the mining industry to enable efficient operation of its existing and projected longwall installations. One task involved in this extensive research project was monitoring ground movements due to longwall mining and evaluating their impact on surface and subsurface structures. This paper presents an analysis of the effects of topography on quasi-static and dynamic ground movements and the severity of damage inflicted on surface structures. The site was chosen for the study with an attempt to obtain a representative account of the topography experienced in the Northern Appalachian region, and more importantly to contain a substantial number of varying topographical features i.e., mountains, hillsides, valleys, and flat bottom land. The study was made possible by typical subsidence monitoring technqiues, however subsidence monuments were surveyed on a frequent basis, intermittently during face advancement. Ground movements were investigated under both quasi-static and dynamic conditions. This provided insight into the propagation of subsidence and the dynamic affects it has upon surface structures.

Jan 1, 1987

By S. E. Phifer

The Haile Gold Mine was the largest gold producer east of the Mississippi River prior to 1942. It is currently the only producing gold mine in the Southeastern United States. Current development involves the mining and heap leaching of some 1000 TPD. Carbon is employed as a recovery medium. Due to its clayey nature and excessive fines in the oxide ore, agglomeration using Portland cement is required prior to leaching. The ore ranges in screen size from two inches to -200 mesh. The agglomerating step combined with certain other conditions has enabled Piedmont Mining Company to achieve recoveries of 90%.

Jan 1, 1987