Search Documents

By R. Mathur

Cu isotope fractionation in low-temperature aqueous environments has been well documented. Here Cu fractionation was applied to two distinct, yet related, mining problems. First, an exploration geology application, where copper isotope fractionation was measured in oxidized leach caps, chalcocite enrichment blankets and hypogene mineralization in three porphyry copper deposits located in the southwestern U.S. Cu isotope patterns exist in a vertical distribution within the mines, coupled with distinct relationships with the Cu grade. Second, a hydrometallurgical application, where copper isotope fractionation was measured in leach fluids, feed and residues from a quick leach test (QLT) on Cañariaco, Peru ores. The results indicate the relative proportions of the minerals providing Cu during leaching. Interpretations of the QLT test measurements indicate covellite is the dominant ore mineral providing Cu during leaching. Both applications clearly demonstrate the use of the Cu isotope technique to understand low-temperature aqueous processes involving copper.

Jan 1, 2012

By İsmail İnce

The existence of water is one of the most effective factors in deterioration of natural building stones. In the process of deterioration, capillary water absorption is the most significant procedure of water penetration into the building stones. Pyroclastic rocks have been widely utilized as building stone especially in historical buildings and monuments since ancient times in the Central Anatolia in Turkey. Nowadays, this type of rocks is used in the restoration of historical buildings as well as in the construction of modern buildings. Pyroclastic rocks are highly susceptible to deterioration process. Capillary rise has a significant influence on water penetration into building stones. Therefore, it is quite important to identify the factors affecting the values of capillarity, capillary rising speed, and capillary rise that define capillary water absorption in these rocks. To this end, pyroclastic rock samples in different textures were compiled from the Cappadocia region, in Central Anatolia. First, petrographic, mineralogical, geochemical, physical, and pore diameter distribution properties of the samples were determined in the laboratory. Then, capillarity values with capillary rise and capillary rise speeds dependent on time were established. Based on the data obtained, correlation coefficients between matrix percentage and capillary water absorption rate and capillary rise values of pyroclastic rocks were calculated and found to be as 0.850 and 0.891, respectively. Thus, the article proposes a new empirical equation to practically calculate the capillary rise value depending on the matrix percentage (MP) and median pore diameter (MPD) values.

Nov 30, 2020

By Harrison R. Cooper

INTRODUCTION AND SUMMARY Phosphate matrix beneficiation is the process of providing a mineral product suitable for downstream chemical processing to yield high analysis chemical fertil- zers. Extraneous contaminants, clays and gangue solids, are separated by screening and flotation. Reject materials always carry with them some phosphate mineral values, however. A continuing objective is minimizing phosphate losses discarded with tailings as a principle factor in maintaining beneficiation efficiency. The quest for efficiency, and improved productivity, during beneficiation is hampered by disturbances arising from among the following: o Natural variance of phosphate deposit compositions, o Minimal control over managing ore matrix supply to the plants, o Screening and flotation mechanical upsets and inefficiencies. Production personnel, in recognizing these factors, attempt corrections for changed process conditions. This response usually has limited effect. Efforts of product- ion personnel to correct for upsets of the process may often diminish efficiencies rather than improve them. Lack of prompt data for analysis of process streams is an important contributing cause of inefficient operation. Discussion in this paper examines methods for improved process control in Florida phosphate beneficiation with particular emphasis on use of on-stream analysis to aid gaining productivity. The Florida Institute of Phosphate Research has supported demonstration of on-stream analysis applicable to improved process control. Concurrently, work is proceeding world-wide in the phosphate industry toward practical on-line analysis technology. Table 1 summarizes viable methods for real-time analysis data as result of work by individual companies and research organizations. A recently completed investigation (sponsored by the Florida Institute of Phosphate Research) of beneficiation efficiency was carried out in two Florida beneficiation plants using a newly developed on-stream analyzer for phosphorus (1). BPL measurements were taken at frequent intervals over two to three weeks of routine operation. Grades are expressed in "BPL", with one BPL, or bone phosphate of lime unit, equal to 0.46 P^Y2^YO^Y5^Y. The time series of feed and tailing BPL data were evaluated by statistical procedures. Results show avoidable losses can be five per cent or greater of mineral values in feed. Use of modern process control methods in Florida phosphate mining began several years ago (2, 3). Benefits of stabilizing control used in one of the two plants where data were collected for the investigation, in comparison to manual control in the other, are outlined. Process control technology developments reported from European and South African phosphate mining operations are also noted (4, 5). It is now well accepted that advanced control techniques can increase beneficiation productivity by better management of losses. However, to make advanced control effective, real-time measurements are needed of feed and tailings BPL as well as mass flow rates.

Jan 1, 1993

By J. A. Bleeck

A discourse on the relationship between industrial minerals and paper production, concentrating on high grade, ultra fine ground calcium carbonate (mean particle size less than 2 microns) and precipitated calcium carbonate. The scope of the paper encompasses four basic areas relevant to the topic: 1. A tutorial overview of the papermaking process with an examination of various industrial mineral components in that process; 2. A discussion of basic technological topics pertinent to the utilization of carbonate in paper with emphasis on the relative aspect. Of natural ground calcium carbonate (GCC) and synthetic precipitated calcium carbonate (PCC); 3. An overview of paper and carbonate market, in both the United State, and Europe with emphasis on (a) current status and future growth trend. Of such market., and (b) discussion of the major influences on growth and development of such market.; and 4. Identification and discussion regarding the principal producers in calcium carbonate markets serving the paper indu.try in Europe and North America.

Jan 1, 1993

We have lived through a period of strong metal pricing during the past eight to 10 years. Copper has been hovering in the range of $3-$4/lb during much of the past eight years, averaging close to $3.30/lb. Gold increased steadily from less than $300/oz levels in the early 2000s, reaching almost $1,890/oz in the third quarter of 2011, before tempering back down to the $1,200-1,400/oz range in 2013. Iron ore prices started to rise in 2005 before the staggering increases experienced in 2008- 2010, reaching almost $190/metric ton in early 2011. During the past four years, iron ore prices have ranged from $100-180/t, averaging approximately $140/t. In the aftermath of such a run, it is perhaps too easy to forget where we have come from: The copper price averaged just 77 cents/lb during the six-year period from 1998 to 2003, and averaged just over $1/lb from 1989 to 1997. The gold price averaged $350/oz during the 10-year period from 1994 to 2003. Even more dramatically, iron ore traded in the range of $10-$15/t between 1985 and 2004. So, we have seen sustained, three- to four-fold increases in copper and gold prices, and 8 to 10-fold increases in iron ore prices.

Mar 1, 2014

By Benjamin K. Pocock

When considering alternative equipment choices in mill or process flowsheets, it is important to determine both capital and operating costs of such equipment as well as other possible savings related to downstream operations. This paper presents a few case studies and shows cursory guidelines for the selection of equipment for new installations or in the retrofitting of existing plants. Based upon recent plant experience, suggestions are given to improve the operation of clarifiers, thickeners and vacuum filters.

Jan 1, 1986

By Louis J. Trostel

Refractories, called the Hidden Industry by The Refractories Institute, provide the temperature and chemically resistant linings for the multitude of vessels that are used today in high temperature processes ranging from giant iron-making blast furnaces to industrial incinerators to petrochemical cracking units to the smallest furnaces used by the jewelry trade. While these refractory linings are absolutely essential to the proper functioning of these processes, the linings are almost always on the inside of the vessels and thus hidden from the eyes of the public. Refractories are defined in Standard C71 of the American Society for Testing and Materials (ASTM), titled "Standard Definitions of Terms Relating to Refractories," as "nonmetallic materials having those chemical and physical properties that make them applicable for structures, or as components of systems, that are exposed to environments above 1 000°F (538°C)." This criterion of ability to withstand exposure to environments above 538OC is the critical distinction separating refractories from other ceramics, fibers, and coatings applicable only at lower temperatures. In addition to resisting temperature, the refractories must with- stand abrasion, chemical and slag attack, resist thermal shock, and carry sustained structural stresses at high operating temperatures for as long as years. The most common methods of classifying refractories are by forming method and composition. First are the traditional formed and fired bricks, batts, and the associated multitude of special shapes. These refractories are usually formed at room temperature, dried, and then fired to high temperatures to develop the final properties desired. Other formed refractories are chemically bonded or resin or tar bonded. To complete the formed refractory matrix, some fired refractory bricks and shapes are subsequently impregnated with resins or tars. Physical dimensions of these formed refractories are classified into two general categories: standard sizes and special shapes. The standard sizes are those in common usage in the United States described in ASTM Standard C909 "Dimensions of a Modular Series of Refractory Brick and Shapes" based on the 38 mm basic module as described in ASTM Standard C861 "Determining Metric Dimensions of Standard Series Refractory Brick and Shapes." The most common size is the "9-inch straight" 228 x 114 x 64 mm (9 x 4 ½ x 2 ½ in.) of the "2 ½ -inch" series or 228 x 114 x 76 mm (9 x 4 ½ x 3 in.) of the "3-inch" series. Bricks of nonstandard sizes are referred to as special shapes. Their use is required in specific furnaces for particular requirements or applications. In addition there is the large and growing group of refractories sold as unshaped mixtures that may be formed into their final shapes at the application site. These unshaped mixtures are sometimes referred to as specialties. The mixtures are prepared to be hydraulically cast, plastic or wet rammed, dry rammed, or dry vibrated into their final shapes. Some are designed to be projected through nozzles (or gunned) onto their forms. The refractory mortars used to lay up the shaped refractories fall into this group referred to as specialties. Prepared refractory grains also are sold. These are usually calcined or fused materials that are subsequently crushed and sized to a variety of specific carefully controlled grain sizes or size distributions. These grains include calcined fire clay, dead burned magnesite, periclase (fused magnesia), dead burned dolomite, kyanite, tabular and fused aluminas, fused zirconia, fused mullite, and calcined alumina-magnesia spinel. The primary composition groups of refractories are the 1) alumino-silicate refractories made largely from fire clay and high- alumina materials, 2) silica refractories made from quartzites and ganisters, and 3) basic refractories from magnesia (or magnesite) and chromia (also referred to as chrome ore), alone and in combination, and dolomite. Special refractories include carbon, zirconia, zircon, high purity alumina, mullite, silicon carbide, silicon nitride, and some borides. In addition there are groups of special insulating refractories.

Jan 1, 1994

By R. Cohen-Alloro

Classical apparatus for granulometric separation generally have limited applications which are found either in the level of the size of separation or in that of the accuracy and the efficiency of the separation or in that of the rate of feed. In industrial practice, the classification of the products of coarse dimensions generally poses no problems. On the contrary, the separation of fine particles presents some difficulties, however the apparatus is used (mechanical classifiers, curved screens and sieves, hydrocyclones, etc...). These difficulties are due to hprfections of separation, rather high cost prices, and sometimes large amounts of recycled materials.

Jan 1, 1970

By T. Kontos

Rogers Group, Inc., is the nation's largest privately held aggregates producer (primarily producing crushed limestone and secondarily sand & gravel) and a major regional asphalt paving construction contractor. The company also has interests in building supplies and coal. Facilities are concentrated in five states in the central U.S. (Ohio, Indiana, Kentucky, Tennessee, and Alabama), with an additional location in Southwestern Virginia. At the request of its then CEO and with support from the company's ownership, Rogers embarked on a strategic planning program in late 1986 by retaining an outside management consulting firm. The ultimate goal of this program was to develop a self-sustaining strategic planning process to inject a strategic dimension into every manager's business thinking and to improve company performance. Since then, Rogers has internalized the outside consultants' strategic planning framework --initially, using it wholesale, and later, greatly streamlining and tailoring both the planning process and product to meet the specific needs of the company. Implementation of strategies developed from strategic planning has resulted in significant improvements throughout the organization. The latest product of the strategic planning effort is a company-wide (or, "corporate") strategic plan that carries the theme of "Market Leadership through Excellence". This paper provides a case study of successful corporate strategic planning by examining the evolution of strategic planning at Rogers and by summarizing the key elements of a sound planning process and product.

Jan 1, 1994

By M. N. Chandraprabha

This paper discusses the role of mineral-adapted acidiphilic microorganism Acidithiobacillus ferrooxidans on the beneficiation of arsenopyrite containing multisulfides (pyrite and chalcopyrite). Adaptation to minerals altered the surface properties of the microorganism. Bacterial adaptation to arsenopyrite and controlled bacterial adhesion to mineral surfaces lead to selectivity in arsenopyrite separation. Bioremoval of arsenic ions (both arsenite and arsenate ions) by Acidithiobacillus ferrooxidans is also discussed.

Jan 1, 2009

By Steven R. Lowe

Construction of a pump station, consisting of an inlet chamber, wet well and pump chamber, required excavation to a depth of 9.7 m (32 ft) below ground surface and more than 7.6 m (25 ft) below the ground water table in a rural, but rapidly developing part of southern New Jersey. Private houses are located [ ] within a few hundred feet of the pump station that use shallow wells for water supply. The pump station design anticipated support of the entire pump station on shallow foundations bearing directly on the underlying natural soils. However, during construction, uncontrolled ground water flow caused ground loss and damage to the bearing qualities of foundation soils. As a result, remedial repairs were required including support of the pump station on drilled pile foundations and releveling of the pump chamber that had settled. This case study is an example of where a poor understanding of the significance of upward flowing ground water had a major impact on the cost of construction. Anticipated subsurface conditions The pump station layout is shown in Fig. 1 with the locations of two borings made prior to construction superimposed. One of the borings was located within the footprint of the deep wet well excavation. Generally, this is not advisable where a deep excavation is required below the ground water table. This is because there is a history of projects where ground water seepage, or pressure, has broken out into an excavation through an ungrouted borehole and compromised the integrity of foundation soils. Logs of the borings did not indicate that the borings [ ] were grouted upon completion.

Jan 1, 2011

By Thomas E. Newman

This paper is a case study using new laser-terrain-mapping technology by EagleScan, Inc., for creating topographic maps. Holnam, Inc., has used this technology to create maps and volumetric calculations of several mines in the United States. The information is superior to conventional methods through accuracy, manpower, time, and cost. Holnam, Inc., was the first cement manufacturer to use the Digital Airborne Topographic Imaging System (DATIS?). The technology uses the DATIS? to produce high-resolution terrain maps and volumetric assessments of any area. DATIS? is a mapping instrument that integrates (1) a Light Detection and Ranging (LIDAR) instrument to measure terrain elevation using laser light, (2) a large-format digital camera, (3) a relative position Global Positioning System (GPS) to measure aircraft position, and (4) an Inertial Measurement Unit (IMU) to measure aircraft attitude. The DATIS? can measure up to 220,000 elevation samples per mil. The system continually collects data on the aircraft's position and measures the time for each laser pulse transmission to return from the ground, giving each sample a GPS reference. The system can operate at night, in overcast sky, and during high-wind conditions and can measure terrain below vegetation cover, unlike standard aerial photography used for traditional surveying and mapping. Surveyed ground-control panels are no longer necessary with this new technology, and only one ground GPS base station located within 60 mi from the aircraft position is required. A computer elevation-point data file is created with the x, y, z coordinates of each laser elevation sample. With this file, CAD engineering programs can create topographic maps that rival products using conventional aerial mapping techniques. Volumetric measurements of stockpiles and pits are also available due to the high density of points collected from an area. This new technology radically changes the turnaround time for map users, giving a product in the format used by today's cartographers. The time line from flight to maps is measured in days instead of weeks.

Jan 1, 1999

By John H. Wright

The United States Antarctic Program (USAP), through its principal support contractor Raytheon Polar Services Co. (RPSC), has recently completed a three-year project comprising nearly 936 m (3,071 ft) of undersnow utility tunnels at Amundsen-Scott Station, South Pole, Antarctica. The tunnel serves the new station facilities that are currently under construction. It houses the piping that conveys fresh water from current and future water well sites, as well as waste water to repositories in abandoned wells. The undersnow tunnels permit year-round access for system operations and maintenance. The network of tunnels is entirely unlined and unsupported. And, for the most part, it maintains a rectangular cross section of 1.8-m-wide x 3-m-high (6 x 10 ft).The tunnel runs from 6 to 14 m (18 to 45 ft) below the surface. Eight 1-m- (3.3-ft-) diam raises bored from the surface serve the network as emergency escapeways.

Jan 1, 2002

By Bart Hogeweg

The development of deep sea mineral deposits creates a new horizon for the mining industry. In a field where mining technology meets deep-water offshore engineering, new challenges are faced to come to the successful exploitation of these deposits. With the absence of proven technology for the mining of these minerals, a ?technological green field? is entered. IHC Merwede (IHC), a global market leader in the dredging and wet mining industry, is on the frontline of these developments. MTI Holland, IHC Merwede?s research and development company, has undertaken a number research efforts focused on the successful development of technology for the mining of deep sea minerals. This paper highlights a number of these efforts and illustrates IHC?s continued dedication for the research and development of technology to enable the commercial mining of deep sea minerals.

Jan 1, 2008

By Leon D. Keller

Fine screening, as discussed in this paper, pertains to the use of the Rapifine DSM Screen to make a 65 to 325-mesh separation at production tonnages. The greatest number of Rapifine Screen installations are in magnetic taconite plants where the unusual relationship between the grinding mill, cyclone classifier, magnetic separators, and fine screens makes the Rapifine Screen application unique. Since the initial fine screening installation on magnetite in 1961, (1) additional installations and further testwork have contributed to the fund of information which is the basis of this paper. The addition of fine screens to the grinding-classifying circuit of a magnetic taconite plant creates a change that effects all components of the circuit. Pine screens in a non-magnetic plant have also been investigated, but here the benefits have not' been as clearly defined. Screens classify according to the particle size. Hydrocyclones classify by a combination of particle size and particle weight. The change in the type of classification minimizes overgrinding of the mineral. The resultant savings in grinding power can be used to increase the throughput, upgrade the product, or increase recovery.

Jan 1, 1971

The Mining Foundation of the Southwest will hold its 14th annual American Mining Hall of Fame awards banquet Saturday, Dec. 7, 1996 at the Leows Ventana Canyon Resort in Tucson, AZ. Each year, preceding the Arizona Conference of SME, the Mining Foundation sponsors this banquet to honor outstanding contributions by people in the mining industry. A permanent display of honoree vitae is located at the Arizona Historical Society in Tucson. Each year, one living award recipient and up to two honorees from mining’s history are chosen by the hall of fame committee and the board of governors of the Mining Foundation. In 1989, the foundation also established a medal of merit to recognize outstanding individual technical and professional contributions to the mining industry. And, in 1995, an award was created to recognize contributions made by companies and individuals in partnership with the mining industry. This year’s inductee is Richard de J. Osborne, chairman, president and chief executive officer of Asarco. He will also be the featured speaker at the banquet.

Jan 1, 1996

By J. Kemeny, R. Fuentealba, C. Rodriguez, F. Fernandez, M. Rocha, T. BoBo

"Mathematical modeling in conjunction with mineral characterization is widely used as a method for design and optimization of comminution circuits, to simulate the processes of crushing, grinding and classification. An important input parameter to the simulation models is the Run-of-Mine Particle Size Distribution (ROM PSD). The run-of-mine size distributions due to blasting have a great influence on the performance of a semi-autogenous grinding (SAG) mill. In this paper, a mine case study was conducted where there are four primary geologic units and the material properties between the four units vary considerably. Also, the mixture of the four unit that will be mined at any given time also vary considerably. This presents a challenge in terms of optimizing the blasting for mill production throughout the mine life. As part of the case study, field rock mass characterization, laboratory rock mechanics tests, and laboratory breakage tests were conducted. The field characterization and rock mechanics tests provide material properties used to simulate the effect of different blast designs on run of mine particle size distributions (ROM PSD). The JKSimBlast software was used for these simulations. The rock breakage tests provide material properties used to simulate crushing and grinding performance. The JKSimMet software was used for these simulations. The goal of the mine is a mill throughput of 95,000 tonnes (104,720 tons) per day (TPD). Based on this goal, run-of-mine fragmentation analysis was conducted for four blasting designs resulting in powder factors of 0.44, 0.54, 0.64, and 0.94 kg/t. The powder factor of 0.44 represents a standard blasting design, while the 0.54 and 0.64 kg/t designs are high-energy blasts specifically to assist with mill production. The 0.94 kg/t design was investigated for the one geologic unit with very high strength. The results of the run-of-mine fragmentation analysis was then input into a crushing and grinding simulation model to predict the mill throughput for the time periods of 1-5 years and 6-10 years. The results indicate that certain blast designs are able to achieve the 95,000 tonnes TPD (104,720 tons TPD) goal, while other blast designs were not. A standard blast design with a 0.44 kg/t powder factor, for example, was not able to achieve the throughput goal, while a design with a 0.64 kg/t powder factor was able to achieve the goal in both the 1-5 and 5-10 year time periods. INTRODUCTION In recent years, mathematical modeling in conjunction with mineral characterization has been widely used as a method for the design and optimization of comminution circuits. The Run-of-Mine Particle Size Distribution (ROM PSD) is a function of rock properties and design parameters of the blast and has a significant impact on the crushing and grinding treatment circuit. Traditionally, design of the grinding treatment is estimated using only the F80 value instead of the full distribution of sizes in the feed, but the finer sizes have great influence on the treatment of a grinder, particularly in the SAG mill."

Jan 1, 2015

By C. J. Pritchard, R. E. Gundersen

I commend the authors on examining an interesting method of shaft lining and attempting to improve safety in a dangerous environment by remotely installing the shaft lining. It is important, though, to not trade off shaft lining safety for long-term mine safety by lining an intake shaft with combustible material. In many operations, the mine utilities are installed next to the lining of the intake shaft, supplying a possible ignition source if damaged or overloaded. Although the polyurethane studied in the paper is of relatively high density, no mention is made of the flame retardency of the samples. When exposed to heat, small amounts of polyurethane will melt and bum but are extinguished when the heat source is removed. If large surface areas of combustible polyurethane - a tunnel or mine shaft- are exposed to ignition heat sources that are not removed or extinguished early, an uncontrollable, fuel rich fire may result with high carbon monoxide levels, low oxygen concentrations, and greatly increased burning rates that can have devastating effects on the ventilation system and miners' safety. Although these heavy polyurethanes lend themselves to a "pouring" application around the annulus of the shaft liners and is a continuous process, past experience with atomizing and frothing polyurethane spray systems indicates a high degree of maintenance and operator attention to the nozzle1 delivery system. This may require more miner's time to be spent in the shaft maintaining the foam system, negating some of the safety advantages of the system. If polyurethane foams are to be used in mines, they must be of the highest quality available in terms of flame spread, heat emitted while curing, and contaminants emitted while curing and spraying. In addition, employees must be given adequate training and be thoroughly informed in all aspects of polyurethane foam safety procedures. As witnessed by our fellow miners in South Africa, we can accept no less.

Jan 1, 1991

The Mine Safety and Health Administration (MSHA) conducted a respirable dust survey to evaluate the effectiveness of a water curtain utilized for dust control on continuous miner sections. The purpose of this survey was to determine if the water curtain was effective in reducing respirable dust concentrations, since several mines currently use water curtains to control miners? respirable dust exposures. The survey was conducted on a supersection of an underground coal mine, which utilized two continuous miners on the same split of air. Each continuous miner alternated taking a cut so that both continuous miners would not operate at the same time. The underground coal mine is located in Knox County, Indiana. The water curtain evaluated in this survey was located in the last open crosscut between the intake side continuous miner and the return side continuous miner. When the intake side continuous miner cuts coal, its exhaust air would be used to ventilate the return side of the section. The intent of the water curtain was to reduce the intake air respirable dust concentration (generated by the intake side continuous miner) before the air stream ventilated the return side of the section. To determine the effectiveness of the water curtain in reducing respirable dust concentrations, respirable dust sampling pumps were placed on both the intake side and the return side of the water curtain. Additional respirable dust sampling pumps were placed farther downstream from the water curtain to monitor dust levels downstream of the water curtain, but in an area where respirable dust would not be created by anything other than the intake side continuous miner or additional section air. The water curtain and the respirable dust sampling pumps were operated only when the intake side continuous miner was cutting coal. The samples were analyzed for respirable dust and quartz content. The water curtain showed minimal effect in controlling respirable dust and respirable quartz dust, but the reduction was so negligible that this survey could not quantify the reduction. The measured reductions are within the accuracy of the sampling equipment.

Jan 1, 2009

By Malcolm Heyburn

Airborne and ground magnetic surveys were made over and in the vicinity of the Sanford Hill ore body at Tahawus, Essex County, New York. These geophysical surveys served to: l. delineate, lithologic and structural features associated with the ore bodies; 2. indicate a major extension of the Sanford Hill ore body; and 3. guide a drilling program to prove this extension. The titaniferous magnetite ore body at Sanford Hill is associated with gabbro occurring in anorthosite. The contrast in the magnetic susceptibilities of these rock types, reflected in the magnetic measurements, allows geologic-mapping showing rock types and inferred structural features. The anomalous magnetic high of the airborne magnetometer survey indicated a southern extension of the Sanford Hill ore body. Diamond drilling, guided by the airborne and specifically the ground magnetic results, substantiated this interpreted ore extension to be of major magnitude.

Jan 1, 1961