Search Documents

By R. M. LaDouceur, C. A. Young, W. Nicholas

"Salicyl hydroxamic acid (SHA) adsorption on two rare earth oxides, lanthanum and yttrium, was studied. Adsorption at both surfaces occurred in two stages. Initially, the monovalent anionic collector appears to adsorb significantly and instantaneously in stage one and then becomes sluggish in stage two presumably because the initial stage passivated the surface. By comparison, adsorption during the sluggish second stage with lanthanum oxide did not stop but with yttrium oxide essentially stopped. Surface monolayer formation could not be observed in either of the two cases. Both stages appear to be due to multilayer formation of a surface precipitate as proven by Raman Spectroscopy for lanthanum oxide but inferred for yttrium oxide. Unlike the use of octyl hydroxamate as stated in the literature, increasing temperatures do not increase adsorption such that flotation of rare earths with SHA may be performed at room temperature leading to improved recoveries as well as significant energy savings. INTRODUCTION Rare Earth Elements (REEs) are comprised of the 15 lanthanides along with scandium and yttrium. The REEs with lower atomic numbers are relatively more abundant and are categorized as light REEs. On the contrary, the REEs with high atomic numbers are less abundant and referred to as heavy REEs. They are not really “rare” and, in fact, some of them are quite abundant in the Earth’s crust; it’s just that they “rarely” exist in concentrated deposits but rather are found dilute and practically everywhere. REEs share very similar physico-chemical properties but, because many of these properties are unique, they have gained enormous importance in recent times making several critical and strategic pending their use. For example, REEs have found extensive application in phosphor coatings, magnetics, and automobile cracking catalysts. Early technology was not advanced enough to produce commodity level production of the REEs and can be attributed to REE-bearing ores containing many rare earth minerals (REMs), not just one. In this regard, there are numerous REMs but bastnaesite, xenotime and monazite are considered to be the most common. Bastnaesite is a fluorocarbonate whereas the other two are phosphates. The separation of the individual REE-bearing minerals from the ores is not an easy task since they also exhibit very similar properties. Consequently, when flotation is used, it is done to produce bulk REM concentrates. For REM flotation, it is well established that octyl hydroxamate is more selective than fatty acid collectors (Pradip and Fuerstenau, 1983 and 1991). Liu et al. (2006) indicated that hydroxamates are the most common collectors for REMs. Pavez et al. (1996) studied the adsorption of oleic fatty acid and octyl hydroxamate on REM surfaces. Cui et al. (2012) studied the interaction of octyl hydroxamate with various REMs surfaces using various spectroscopic techniques such as XPS, FT-IR and Raman along with electron microscopy and concluded that such techniques offer ample information to establish adsorption mechanisms. Ren et al. (1997) studied napthalenic hydroxamic acid as a unique collector for flotation of REMs from bastnaesite ore and indicated that more selective collectors were needed. From these studies, it is clear that the quest of more selective collectors is essential but understanding how they adsorb at mineral surfaces is prerequisite to improving flotation performance."

Jan 1, 2016

By C. Arthur Lefler

The Smoky Valley Mine is jointly owned by Louisiana Land and Exploration Company, Felmont Oil Corporation and Case Pomeroy Company. Copper Range Company, a subsidiary of L.L. & E. is the operator of the mine. The mine is located about 60 miles (100 km) north of Tonopah, Nevada on Highway 376 (formerly 8A) in the Big Smoky Valley on the western flank of the Toquima Mountain Range In the shadow of Mount Jefferson. The mine is at an elevation of about 6100 ft. (1860m) and is situated on the southwestern flank of Round Mountain, the hill for which the town of Round Mountain is named. The ore is a rhyolitic iglmbrite with coarse gold occurring along fractures and with fine microscopic gold disseminated in the rock mass. Minor silver is associated nth gold. Annual mining is planned at 5.8 million tons (5.3 million tonnes) per year with 2.2 million tons (2 million tonnes) as ore (7,000 tons or 6,400 tonnes per day).

Jan 1, 1981

By Michelle Stokes, Alexandra Miller, Campbell McKenzie

"The ancestral Ringarooma River in northeast Tasmania has transported alluvial tin and other heavy minerals from their onshore source of stanniferous Devonian granites downstream into what is now Ringarooma Bay. Previous exploration work has demonstrated the presence of potentially economic tin mineralisation within the palaeochannels and terraces associated with the submerged river.The offshore tin resource lies directly on the seabed or with less than 2 m of overburden, and within 5 - 50 m water depths in the wider bay area. The main river channel continues offshore for at least 13 km, with high tin grades found within the palaeochannel but also dispersed across the sea floor as a sheet wash, a result of Quaternary sea level change reworking the placer deposits. This drowned portion of the coastal plain contains a continuation of rich tin leads as low gradient anastomosing channels, and has been delineated by marine seismic and drilling activity since the 1960s. Tin grades in the Tertiary and Quaternary alluvial profiles vary from 50 - 300 g/m3, with the highest concentrations in the coarser basal horizons. A previous offshore explorer estimated a resource of 194 Mm3 at 150 - 250 g/m3.Kenex Ltd created 3D models of the paleochannels and the mineralisation with the aim of better constraining the resource estimate and identifying additional depositional areas. The modelling was undertaken with the input of geophysical data, bathymetry and geochemical sampling of the seabed surface and from historic offshore drill holes. A prospectivity model covering Ringarooma Bay was produced to target tin-bearing gravels. Predictive maps were created to represent various features of the offshore mineral system, including assessing gradient changes in palaeochannels and their sinuosity. The model identifies areas with higher potential for alluvial tin mineralisation and will be used to focus the exploration programme over tenements currently held by Kenex Ltd."

Sep 1, 2014

By Reinhold Schulze

Thiourea is being applied as an industrial leaching agent for gold and silver only in a few cases. A CIP technique was developed which eliminates most of the obstacles against its use. Mild conditions for precious metals stripping from the loaded carbon simplifies process conditions in comparison to cyanide CIP technique. Examples are given.

Jan 1, 1998

By H. J. Handewith

This paper explores the state-of-the-art of mechanical rock drilling and boring methods in use in the year 2000. It covers the basic mechanisms of cutting tool design and outlines the current understanding of related rock fracture methods. It provides suggestions for future research needs and discusses the mining and construction markets that are driving these needs.

Jan 1, 2001

By R. L. Guerguerian

Nowadays, most grinding mills driven by a wrap-around ring motor are operating successfully. Some of the earlier problems could be attributed to the lateral stiffness and stability of their bearings. As a result, modifications to the bearings included the rearrangement of the shoes, or the addition of more shoes, closer to the horizontal centerline. This technical paper reports a study of the effects of bearings on the lateral stiffness of grinding mills driven by a wrap-around ring motor. The discussions cover the design of the four shoe trunnion bearings and examine the effects of the angular location of the shoes.

Jan 1, 2000

By ZHONGLING ZHAO, WANTING SONG, GUOZHONG LIU, LEIXIN SHI, ZUI WANG, YUANYUAN LIU, KE GAO, DONGHONG JIANG, WANG LUO, PEICHAO LU, Jianwei Cheng, WANCHENG ZHENG, Gang Zhao, YUNGANG WANG, JIANBING ZHAO

Coal spontaneous combustion is one of the major disasters in coal mines, and it can have devastating effects on the normal mining and production activities of mines. This paper presents the field investigation, field measurement, data analysis, and formulation of fire-extinguishing measures conducted to extinguish the fire from a coal spontaneous combustion incident that occurred in a high-gas coal mine in China.

By J. A. Chermak

Piles of sulfide-bearing overburden, ore, and tailings have the potential to generate acid drainage (AD) when exposed to an oxidizing environment. Laboratory column experiments were conducted using acid-generating overburden material with an added surface amendment of limestone and/or lime. Artificial rainwater was introduced and allowed to drain through the columns. Results showed that the limestone and/or lime reacted with the acidic rock, resulting in the precipitation of a hardpan layer of gypsum and amorphous iron oxy-hydroxide at the surface. The hardpan layer significantly reduced the effective permeability of the column. Based on this study, hardpan layers can be created as chemical caps to significantly reduce the infiltration of rainwater and snowmelt into acidic overburden or tailings material. Unlike traditional capping methods (for example, clay and high density polyethylene (HDPE) covers), chemical caps are self-healing.

Jan 1, 1996

By F. M. Doyle

Metal removal kinetics and metal ion selectivity in ion flotation were studied from a thermodynamic perspective. Surface tension data could be used with the Gibbs adsorption equation to quantitatively predict the metal ion removal kinetics in alkylsulfate-Cu systems. However, surface tensions predicted cation selectivity coefficients in the sodium dodecyl-sulfate (SDS)-Cu-Ca and SDS-Cu-Pb systems rather poorly, although the predicted order of the selectivity (Cu2+<Ca2+<Pb2+) was correct. Another thermodynamic selectivity model, which used the Grahame adsorption equation and a geometrical analysis, predicted cation selectivity coefficients that agreed very well with experimentally measured values.

Jan 1, 2000

Newmont Gold&apos;s methods for deposit modeling vary, depending on geology, mining and processing methods, economic feasibility and availability of historical information. It is argued that successful modeling requires understanding these factors, knowing the strengths and weaknesses of the various modeling techniques and being flexible in selecting the appropriate methods. Newmont is one of the world&apos;s largest gold mining companies, with operations in the United States, Peru, Mexico, Indonesia and Uzbekistan. And it is active in exploration worldwide. At the end of 1996, Newmont declared a total reserve of 1.15 equity kt (37.1 million equity oz) of gold and 2.17 equity Mt (2.39 million st) of copper. The gold deposits managed by Newmont totaled 752 Mt (829 million st) of ore containing 1.28 kt (41.3 million oz) of gold averaging 1.71 g/t (0.05 oz/st). In addition, Newmont is developing a porphyry copper-gold deposit that totals 9.1 Gt (1 billion st) of ore containing 380 t (12.1 million oz) of gold and 4.82 Mt (5.32 million st) of copper. (In May 1997, Newmont Gold Co. merged with Santa Fe Pacific Gold Corp., thus increasing Newmont&apos;s reserves to 1.72 kt or 55.2 million oz of gold and 2.17 Mt or 2.39 million st of copper.)

Jan 1, 1998

By B. C. Lewis

Have technological advancements in underground coal mining driven people&apos;s skills to new highs or have the expanded skills of mining people driven the industry&apos;s technological advancements. Who knows? What we do know is that both our technology and our people have made meaningful and significant advancements. Overall, longwall systems continue to increase productivity and retreat faster. Globally, gate road development is the primary bottleneck in a longwall mine. The primary bottleneck in gate road development is roofbolting. Generally, roofbolting is the bottleneck in room and pillar operations as well. This paper will present an integrated manufacturer&apos;s (Joy Mining Machinery) vision of the future in comparison to current equipment performance. Particular emphasis will be placed on roofbolter technologies.

Jan 1, 1999

By C. Bemelmans

Lead alloys function effectively as oxygen evolving anodes in copper SX-EW operations and are highly resistant to corrosion. The presence of organic from solvent extraction in the electrolyte seemed to enhance solution line attack. Laboratory tests showed that lead is soluble in D2EHPA, Acorga and LIX 984 to a limited, yet measurable degree. Lead alloys and various lead phases formed on the anode were tested to evaluate their effect on the corrosion process in organic media. Possible causes for anode corrosion and mechanisms responsible for their initiation will be discussed.

Jan 1, 1996

By Edward M. Jacobs

In some ore grinding circuits it is desirable to make separations purely on size. The normal choice for this is vibrating screen equipment. Developments in screening process technology have led to improvements in the capacity and efficiency of vibrating screens, through the adoption "Thin Layer Wet Screening". This process can reduce recirculating loads and equipment requirements in the ore grinding circuit.

Jan 1, 1985

By Patrick J. Doig

The contract for the construction of the Inline Pump Station for the Milwaukee Metropolitan Sewerage District involves the sinking of three shafts and the excavation of a pump chamber. The shafts are being sunk to a depth of 104 meters and pass through 52m of sediments before encountering dolomitic bedrock. The pump chamber is constructed in dolomite. The sediments are alluvial, estuarine and lacustrine in origin, with some ice margin deposits. They comprise loosely consolidated fine to coarse grained sand, silts, clays and gravels, and they are heavily saturated with a water content often above 60%. The water table is at a depth of 3m. The dolomite is silurian, generally dense, with some clay-filled vugs and shale partings. Until 1983, underground construction in the Milwaukee area had been limited to depths of 26m in the sediments and 20m in the dolomites. Water control methods had included caissons, compressed air, extensive internal and external dewatering, and grouting. Flows of 20 liters per second were commonplace with as much as 80 liters per second being encountered in the rock. However, in 1984 work was commenced on the deep sections of the Milwaukee sewerage scheme with the letting of three major contracts including the Inline Pump Station. With excavation taking place at greater depths, it become obvious that previous methods of water control would be inappropriate. To protect against major inrushes of high pressure water in the rock, an extensive program of pre-grouting from the surface was specified. Water control in the sediments was left to the discretion of the contractor and in each case freezing was choosen. This paper describes in detail the grouting and freezing procedures.

Jan 1, 1985

By L. G. Hagenbuch

Several factors need to come together in creating an integrate mining equipment dispatching system. At the hub of these factors ace the central dispatching formulas. This paper details the development of these central dispatching formulas and explores the combining of these formulas with other elements to create an integrated dispatching decision. WHY DISPATCHING? Truck dispatching implies and in reality should equate to mine equipment efficiency. Good truck dispatching will yield good mine equipment efficiency while poor truck dispatching will yield the alternative. Truck dispatching can either be automated through a computerized, process or it can be manual. Every mine with haul trucks has a truck dispatching system whether it is recognized or not. Even a system wherein the hauler operators determine where they are going for their next load is a truck dispatching system.

Jan 1, 1987

By N. Sheikh

In galena flotation, lead ethyl xanthate, Pb(EtX)2, is precipitated and is physically adsorbed in the form of multilayers on the chemically adsorbed first layer of Pb(EtX). 1,2) The solid particles are coated with layers of Pb(EtX)2 in heterogeneous manner over surface areas possessing both anodic and cathodic character (3,4) It is anticipated that the mode of formation of Pb(EtX)2 and the number of ions present, together with stable or unstable by-product species, have great influence on the surface characteristics of galena. The information obtained from a study of these parameters may have important practical applications in flotation. Lead ethyl xanthate is sparingly soluble in water. The metal and xanthate ions released to the aqueous solution during its dissolution undergo various types of reactions depending upon the pH values of the system. Extensive work (5,6) has been carried out to elucidate the mechanism involved in acid decomposition of xanthate ions. Different decomposition paths (7,8) have been proposed for the hydrolytic decomposition of xanthate in neutral and alkaline solutions, The concentrations of lead ions vary due to a number of chemical reactions, regulated by the pH and the temperature of the bulk phase. The hydrophobic character of Pb(EtX)2 may change with the nature of chemical reactions. Some of the numerous by-product species in solution may adsorb on the solid and change the properties of surface film either favourably or adversely. The flotation performance of galena, therefore, may depend to a considerable extent on the physical and chemical stabil¬ity of Pb(EtX)2 layers. Since little work has been reported in literature dealing with the stability of Pb(EtX)2 and its correlation with the flotation of galena, attempts have been made In this study to evaluate the behaviour of freshly formed Pb(EtX)2 in aqueous systems at various pH values.

Jan 1, 1971

By John M. Dale

Now that the price of sulfur has reached unexpected high levels, it is little wonder that sulfur from surface ores is again receiving attention. In most instances, it is advantageous for an ore to be at or near the surface. However, it is a distinct disadvantage for sulfur ore to be close to the surface because it precludes the use of the Frasch process. The Frasch process depends on the presence of at least 180 m of uniform overburden to allow pressure injection of superheated water into the sulfur-bearing formation to melt the sulfur. In the Frasch process, sulfur separates cleanly from the gangue underground and comes to the surface in a very pure form. Surface sulfur deposits, particularly those in the Western Hemisphere, exist largely due to volcanic activity, and sulfur separation from the gangue is a formidable technical problem. None of the surface deposits are large compared to some of the Frasch deposits, but at the present sulfur price, they are certainly of economic importance. From the turn of the century until 1975, the price of sulfur was for the most part $18-$28/t. However, with the price of sulfur now over $154/t, there are a variety of technical alternatives to consider for sulfur surface ore separation that may not have been economically attractive a few years ago.

Jan 9, 1981

By Douglas Beahm

Energy Metals Corp. (EMC) holds numerous mineral properties in the northern portion of the Great Divide Basin. The JAB property is one of several potential properties being planned for development as a satellite facility to the greater Antelope uranium project. A National Instrument 43-101 Technical Report was completed for the JAB property. This report estimated total measured and indicated mineral resources on the property totaling 1.6 kt (3,555,022 lbs) U3O8 contained in 2.2 Mt (2.4 million st) at an average grade of 0.073 percent U3O8 at a 0.25 grade times thickness (GT) cutoff in accordance with CIM Standards on Mineral Resources and Reserves. The JAB property is located in Sections 13, 14, 15, 16, 21, 22 and 23, Township 26 North, Range 94 West, approximately Latitude 42° 14’ North and Longitude 108° 00’ West (Fig. 1). This property consists of unpatented mining lode claims and Wyoming state mineral leases com-prising approximately 850 hm2 (2,100 acres).

Jan 1, 2007

By Alexander N. Winchell

"Location. The Cuyuna iron district extends from the region of Kimberly, near the Center of Aitkin County, Minnesota, south-westward through Deerwood, Ironton, and Brainerd, across Crow Wing and Todd counties, across the Mississippi River, and for an unknown distance farther southwest in the same direction. It is known that the Huronian rocks, in which the ores of the Cuyuna district are found, reappear near the western border f Minnesota, but no ores have been found in this region. The district has a length of more than sixty miles, but the more important portion as now known &apos;is confined to Crow Wing County in an area which is less than thirty miles in its longest dimension. The commercial headquarters for the district are in the city f Brainerd, on the Mississippi River.History. The discovery of iron ore in the Cuyuna district was accomplished with no aid from surface outcrops, but solely through the use of the dip needle. The mantle of glacial drift overlying the iron formation varies from twenty-five to 359 feet in thickness, and it was by means f the magnetic attraction of the iron bearing rocks that their presence was discovered with the dip needle by Cuyler Adams, about 1895. The general geologic map of Minnesota, published by the State Geological Survey in 1909, showed the extension of the Huronian rocks of the Mesabi district passing through this area. Two years later, Leith published a sketch showing the hypothetic extension of the iron bearing formation through the same area. The first drilling was done in 1903, near Deerwood, Minn., by Cuyler Adams, and exploration was continued to the present time in increasing amount. The Northern Pacific Railway extends throughout the length of the district and affords an easy outlet for the ores. The Soo Line Railway completed a spur into the district in 1910. Both roads carry the ore to the docks at Supe¬rior, Wis., the average haul being about ninety miles. Shipments began in 1911, the Kennedy mine being the first producer. By 1918, the number of shippers reached twenty-seven, with a total output of nearly two and one-half million tons for that year."

Jan 1, 1920

By Gabriel de Almeida

INTRODUCTION The widespread use of desktop computers by an ever increasing number of people, both for personal and for business and government uses, has brought public attention to surprising stories about computer abuse. Before the advent of microcomputers in the information processing environment, hundreds of amazing misdeeds involving large computers had already been reported, most of them perpetrated by highly skilled professionals. The undreamed enlarging of microcomputer potential has steadily posed a major threat to complex mainframe computing systems, as joyful teenagers become familiar with the habit of hacking around someone else&apos;s large processing system, by means of makeshift phone communication networks, based on their intended homework for personal computers -- for the sheer fun of it. Now, the never ending capacity and speed improvement of commercially available micros has given rise to a brand new concern for society: the hazards of processing sensitive information in the powerful, but still unsafe microcomputer itself, whether or not linked to other micros or mainframe networks. This paper deals with some aspects of the problems and presents some practical hints as to enhance protection and minimize risks to sensitive and secretive information when processed on microcomputers. The physical considerations of computer security and pertinent safety precautions will not be discussed, because while essentially relevant to information protection, recommendations are well defined by processing resources suppliers and their importance is more widely recognized by users in general. Definitions and Classifications. The following definitions and classifications will be considered in this report: Information Assets: Any knowledge or information processing, storing or conveying device displayed in one&apos;s environment. It consists of two main categories: INFORMATION RESOURCES: End user&apos;s application data wherever recorded. PROCESSING RESOURCES: EDP skilled user&apos;s hardware, software, peripherals, magnetic media, communication devices, auxiliary equipment, supplies and related operational procedures. Information Protection: In a broad sense this is the set of necessary procedures to assure to the legitimate user the effective control of the operation and allow modifications of information assets, so that their physical or cognitive integrity be preserved or any unexpected loss minimized inspite of accidental occurrences or intentional actions. Classification Processes: Commonly two classification processes are used to define key terms in information protection: SENSITIVE CLASSIFICATION: Pre-defined standards for assessing the vulnerability to losses due to lack of proper processing continuity if information is destroyed, disclosed, secluded, or misused. SECRECY CLASSIFICATION: A spectrum of degrees as to the expectancy of holding exclusiveness of unique information whose destruction, disclosure, seclusion or misuse will cause a negative impact on the legitimate holder environment. Sensitive Information: Any knowledge whose destruction. disclosure. seclusion or misuse - - - implies losses to its legitimate holder. It may be classified as: VITAL INFORMATION: An essential knowledge whose lack of proper availability implies total loss or termination of p

Jan 1, 1987