Search Documents

By Jan Wolski, Jack Barry

Ventilation ductlines with a single fan or with a series of fans are analyzed. The duct friction loss factors are discussed. Numerical solutions, presented in the paper, applies to any fan number and locations along a duct line. The findings are compared with formulas available in the technical literature. Values of the air leakage factors are presented in the SI, technical metric, and US unit systems. A method is shown of how to determine the leak- age factor for a given ductline. Optimum solutions for the sample duct lines with two and five fans in series are discussed and presented in a graphical form. Performance of fans in series is discussed in conjunction with both friction pressure loss and leak- age.

Jan 1, 1997

By N. Rajmohan, K. T. Jacob

Presented is a thermodynamic feasibility analysis of extracting base metal chlorides from low-grade, multi-metallic oxide ores using CaC[1]2 as a chlorinating agent in the presence of SO2 and O2. The oxides react to form corresponding chlorides, while CaC[1]2 is converted to CaSO4. The Ellingham diagram is used for comparing the standard Gibbs' free energy change for the sulfation-chlorination reaction of a large number of oxides. Except for alumina, silica and chromia, most of the other metal oxides will be converted to their respective chlorides. The volatile chlorides can be condensed, and the chlorides present in the condensed state can be leached. A process is proposed that uses a nontoxic chlorinating agent and gives an efficient separation of the metallic values from the gangue.

Jan 1, 1993

By Daniel C. McLean

Chemistry plays a more important role in milling operations than is generally recognized, particularly in fluid- solid separation processes. Chemical aspects are also very important insofar as plant water quality is concerned, and in the manner in which this water quality effects plant design and operation. Aside from the inherent chemical characteristics of plant water, the mineral preparation industry is becoming increasingly more dependent on the use of mining chemical reagents--relatively new to the coal industry, but items of I standard usage in complex metal recovery plants. These chemicals have many useful properties and can produce significant improvements in operations and metallurgical efficiencies when used properly and intelligently. They can produce poor results and sometimes severe losses when used improperly. Most reagents are relatively expensive on a per pound basis, hence costs can be excessive if they are used wastefully or inefficiently.

Jan 1, 1968

Komatsu America International has introduced two new hydraulic excavators. They can work in congested and confined areas. The tight tail swing radius of the PC128US-2 and PC22-8USLC-2 enables the excavators to minimize the work space. The units can operate in confined work settings that are inaccessible or counterproductive to traditional machines. Even the door is designed for tight working conditions. A convex door slides open along the exterior curve of the cab, rather than swinging out on hinges past tracks. And the excavators’ tight tail swing design allows them to load within the track width of the machine.

Jan 1, 2000

By Robert C. Schenk

The rapidly expanding, globally based mining industry provides many opportunities and challenges for the engineering construction business. This paper reviews some of the innovations that the industry is implementing to provide increased value in the design, construction, and successful start-up of new mine plant facilities. Approaches being taken to reduce installed-plant costs as well as related value-enhancement opportunities are discussed. Included are comments on new technology developments, use of automation and global communications networks, application of economic models as a project design tool, and management approaches being adopted to make the engineering construction process significantly more effective.

Jan 1, 1998

By A. Jarosz

The surface manifestation of underground mining usually entails five distinct types of surface movements, which can affect or damage surface structures, facilities and renewable resources. These movements developing at the surface can be described by (Bell, 1975; Bhattacharya and Singh, 1984): - vertical displacement, i.e. subsidence, - horizontal displacements, - slope or tilt, i.e. the derivative of the vertical displacement with respect to the horizontal distance, - curvature, i.e. the second derivative of the vertical displacement with respect to the horizontal distance, and, - horizontal strain, i.e. the derivative of the horizontal displacement with respect to the horizontal distance.

Jan 1, 1986

By Harold E. Goetzman, Blair R. Benner

The U.S. iron ore industry is located primarily in Northern Minnesota and Michigan's Upper Peninsula with one additional small plant in Missouri. There are currently some 10 plants operating that produce about 48 million tons per year of pellets. The major reagent use occurs in the three general areas of: flocculation, flotation and pellet additives. Minor areas of usage are for corrosion inhibition and dust suppression. Current practice as to types of reagents, consumption, and method of application are reviewed. The interaction of reagents with other parts of the process are discussed. Also included is a discussion of future reagent needs.

Jan 1, 1994

By Peter J. Borchardt, Helen M. K. Andersson, Donald A. Bruce

Grouting is a useful engineering tool for tunnels throughout the world. A wide variety of methods and materials are used, reflecting the broad range of geological, hydrogeological, and structural demands. Most tunnel grouting is conducted with cement, which produces acceptable results in appropriate conditions. However, there are cases where such grouts are not practical, but polyurethane grouts can be extremely useful. Regretfully, these grouts are frequently poorly understood, leading to improper application and therefore poor results. This paper provides a fundamental overview of their application, both used individually and in combination with cement. Case histories from Scandinavian practice are cited.

Jan 1, 2001

By A. L. Wilder, S. N. Dixon

Introduction Coeur d'Alene Mines Corp.'s largest precious metals property is located in the historic Rochester Mining District 40 km (25 miles) northeast of Lovelock, NV. The property encountered cold weather operational problems soon after its fall start-up in 1986 due to its elevation of over 1830 m (6000 ft). The problem of ice buildup on the heaps because of sprayed solution application was faced immediately. It was felt that allowing ice to build up all winter long until a spring thaw was impractical due to the large area under leach. Further, the operating cost and delivery schedule for a solution heating system was unacceptable. The development and installation of a leach solution distribution system using drip emitters made efficient, cost-effective winter operation possible. Other benefits of this system have also been observed and are discussed here. General process description 15,422 kt/day (17,000 stpd) of - 1.27-cm (-1 /2-in) crushed ore from the three-stage crushing plant are delivered to the leach pad using 77.1 t (85 st) rear dump haul trucks. The ore is drifted into place with a D-9 bulldozer. Leach panels are contiguous and are approximately 8861 m'(90,000 square ft) in area built in 6-m (20-ft) lifts. New panels are built on top of older areas to a final height of 61 m (200 ft). Each panel is ripped and cross-ripped prior to leaching. Barren solution is distributed to the heap using drip emitters at rates of 0.02 to 0.41 L/min/m2 (0.0005 to 0.01 gpm per sq ft), depending on the age of the panels. The pH of the leach solution is 10.7 with a cyanide concentration of 0.75 kg/t (1.5 lb per st). Approximately 50% of the silver and 80% of the gold are finally recovered. Pregnant solution percolates though the heap and flows by gravity into one of two 9.46 ML (2.5 million gal) pregnant solution ponds. The solution is then pumped to a conventional Merrill-Crowe process plant. Clarification takes place in three 9464 L/min (2,500 gpm) capacity filters. The solution is then pumped to a packed vacuum deareation tower for the removal of dissolved oxygen. Typical deareated solution contains 0.7 parts per million dissolved oxygen. Precipitation of gold and silver is accomplished by adding a zinc dust slurry to the deareated solution at the suction of the filter press feed pump. Precipitated gold and silver are recovered in three recessed plate and frame filter presses. Barren solution is discharged into a 11.7 ML (3.1 million gal) pond where cyanide makeup occurs. This solution is pumped back to the heap for further leaching. The precipitate filter cake, containing approximately 75% dore (Ag + Au), is then fluxed with anhydrous borax, soda ash, sodium nitrate and fluorspar to yield a neutral, bisilicate slag. The fluxed precipitate is then charged into a propane-fired melting furnace and heated to 1150° C (2100° F) for 3 1/2 hours. Slag and dore bullion are poured into conical cast iron pots yielding buttons of 800 to 1000 troy oz. The dore typically contains 98.5% silver and 1 % gold. Slag is crushed and tabled to recover the trapped dore blebs and beads. Concentrate from the table is returned to the furnace. Table tails are sent to the crushing circuit and out to the leach pad. Solution application The area kept under leach at Rochester is approximately 130 000 m2 (1.4 million sq ft). Barren solution is delivered to the pad at 21.2 kL/min (5600 gpm) for a resultant application rate of 0.16 L/min/m2 (0.004 gpm per sq ft). A traditional solution sprinkling system using No. 12 Senninger Wobblers with individual pressure regulators was installed at the onset of leaching activities. The Wobblers were placed at 9.1-m (30¬ft) staggered centers and were fed off of a gridwork of Yellowmine plastic piping. Solution flow rates were moni¬tored to each panel. The onset of cold weather with an average nighttime temperature of -12° C (10° F) made it apparent that continual operation would not be possible with the sprinklers. A significant amount of ice was built up on top of the heap, making maintenance and pipe removal dangerous, if not impossible. Leach solution application was restricted to daylight hours to inhibit ice formation. Process plant flow rates were reduced to maintain steady-state operating conditions. However, as daylight temperatures dropped below freezing, ice continued to accumulate due to the sprays. Besides the obvious operating hazards brought on by the growing icefield, there was also the potential environmental hazard associated with an early thaw melting the ice too rapidly for the solution containment facilities. One other option for preventing ice formation was heating of the barren solution prior to spraying. Initial plant design allowed for expansion of the propane storage and distribution system as well as modification of the barren piping for a solution heater. This option was not exercised because the operating costs for an adequate system would have been prohibitive, and timely delivery of a system was not available. An investigation was conducted on the various drip irriga¬tion products available, since subsurface solution applicators would eliminate ice formation altogether. Systems utilizing external flow emitters were ruled out because of their ten¬dency to clog when buried. Emitter systems using perforated tubing were also eliminated from consideration due to their inability to adequately control flow over required lengths of tubing. An in-line emitter system was finally selected which demonstrated clog resistance and adequate flow control, enabling direct burial.

Jan 1, 1990

By Jerome A. Westphal

The Middle Mississippi River extends from the mouth of the Ohio River to the mouth of the Missouri River, a distance of about 310 kilometers (km) measured along the river. From its founding in 1764 to the first steamboat arrival in 1817, the City of St. Louis was little more than a trading post. However, with the advent of the shallow-draft steamboat, the Middle Mississippi River rapidly became a major thoroughfare of commerce. In this regard, its importance has been reflected by the development of port facilities at St. Louis and by Federal activity relating to channel maintenance and improvement. First Federal work on the Middle Mississippi River was autho¬rized by Congress in 1824. This work was for snag removal and bank clearing and was directed at reducing the hazards to steamboat traffic, particularly during low-flow periods. During the 1820's and early 1830's, the main channel threatened to move toward the Illinois shore and abandon the St. Louis port facilities. In 1836 and 1837, Congress authorized construction of permanent improvements to keep-the river next to St. Louis (Missouri shore). By 1880, it was recognized that bank clearing activities had resulted in a wider and shallower river which exacerbated navigation

Jan 1, 1977

By A. Pavlides

The purpose of this study is to compare estimation methods for lignite reserves at the Amyndeo mine and to provide a map of the estimated thickness of the coal seams. The reserves are first estimated with the method of Voronoi diagrams, using a group of mirror points to close the polygons around the boundaries of the mine. The second estimation method is based on Ordinary Kriging using the Spartan variogram model. Finally, the reserves are estimated by the mean lignite thickness value of the drill-hole data Two data sets are investigated. The first one corresponds to an exhausted part of the mine. The derived reserves estimates are compared with the actual data obtained by the Public Power Corporation (PPC) to validate the analysis. The second data set extends over the entire mine, and it is used to derive an approximate estimate of the total lignite reserves. A geostatistical analysis of the total layer thickness is performed. An interpolated kriging map of the total thickness variation is produced accompanied by a map of the kriging uncertainty.

Jan 1, 2008

By James S. Browning

Extensive deposits of kyanite occur in the southeastern United States, The reserves of these deposits, if developed, are adequate to supply the United States with 35-mesh kyanite concentrate:; for many years at the present-rate of consumption, According to Espenshade and Potter,1 the kyanite-quartz rock type deposits in this area contain about 100 million tons of ore averaging 10 to 30 percent kyanite. The tonnage of kyanite-bearing gneiss and schist is, much larger than the tonnage of kyanite-quartz rock, but the kyanite gneiss and schist are appreciably lower in grade. The largest deposits of kyanite-quartz rock are in the Farmville district, Virginia, and Kings Mountain district, North Carolina South Carolina, and at Graves Mountain, Georgia. Of the known deposits, only four were being mined for kyanite in 1967. These deposits are near Farmville and Dillwyn, Va., Clover S. C., and Washington, Ga. Production of kyanite and synthetic mullite increased substantially in 1965.2 Output of, domestic kyanite concentrate increased by 14 percent in 1965, establishing a record high for the fifth consecutive year. Estimated annual consumption of kyanite minerals and synthetic mullite was in excess of 100,000 tons. The manufacture of mulatto refractories accounts for most of the kyanite minerals consumed annually, but non-refractory uses are expanding.3 Most mullite refractories are used as furnace linings in metallurgical and glass manufacturing furnaces. The remainder is used largely for kilns, kiln furniture, and saggers by the ceramic industry. Small quantities of kyanite without calcination are used as a source of alumina in the manufacture of glass, electrical and chemical, porcelain, pyrometer tubes, and in the form of kyanite concentrate to increase the alumina content of fireclays. Kyanite is used to improve workability, increase strength, and to compensate for firing shrinkage in floor and wall tile and other ceramic products.

Jan 1, 1968

By Y. S. Roditis

Traditionally, open pit optimization has been used to produce a single outline which can guide the pit design. This paper describes how a series of optimum nested pits are utilized to: a. produce different mining sequences and to help in mine planning and phase design; b. evaluate different metallurgical processes, production scenarios and equipment size; c. investigate the sensitivity of a project to prices, recoveries, production rates, costs, ultimate pit slopes etc.

Jan 1, 1993

By L. Frederick

Measurement of gamma radiation occurring in nature to characterize geological formations has been widely recognized in mineral exploration. Different methods and apparatuses have been developed for drill hole logging purposes. Geological formations vary in amount of naturally emitted gamma radiation. A gamma signature from a geological formation is captured by utilizing different types of gamma detectors. A natural gamma radiation detector (NGRD) can be used to control mining whenever there is a significant difference between the radiation levels in the mineral or ore being mined and the waste materials surrounding the ore. Surface miners, such as the one shown in Figure 1, can precisely control the elevation of the cutter as the machine moves over the surface of the formation. This type of machine is predominantly used in selective mining operations, e.g. surface coal mining. If there is a means to know the position of the cutter relative to the interface between the ore and waste, the miner can recover all or most all of the valuable mineral with very little out-of-seam dilution. This paper discusses the results of a successful application of gamma detectors to control a surface miner at one of North American Coal Corporations? locations - Red Hills Mine. The mine has nine coal seams in total with thicknesses ranging from 12? to 60?. The bottom six seams (Figure 2) are minable. The mine has complex geology and a significant amount of annual rainfall (4.7 ft). The mine produces approximately 3.5 million tons of coal and about 40 bcy of overburden per year. The operation utilizes diverse mining equipment including Dragline Marion 8200, electric shovel P&H 2800, Caterpillar end dump trucks CAT 785 and 789; bulldozers CAT D11, D10, D8, and D6. Coal is mainly extracted by utilizing a Wirtgen SM 4200 surface miner that is loading CAT 785 trucks with high volume coal bodies and payload of 150 t. Operational cutting depth is 24 inches with maximum cutting depth of 36 inches. Surface miner operators determine a cutting depth based on multiple cues, the most important being visual observations of a coal seam being cleaned or mined. The cleaning process involves removal of the last foot of waste material covering the coal seam. This is one of two critical phases in the coal extraction process. If, during the cleaning process, an operator sets a cutting head too deep, valuable product is wasted. If it is set too shallow, waste material is left to be mined with the coal. The second critical phase occurs in the last cut on the interface between the coal and waste material at the bottom of the coal seam. If the cutting head goes deeper than favorable, then waste material is delivered to a power plant.

Feb 27, 2013

By James J. Brady, James S. Lewis, Robert B. Gordon, Jimmy W. Honeycutt

INTRODUCTION Tunnel construction has always been an extremely high risk form of contracting primarily due to the inaccessability of information concerning the ground conditions to be encountered during excavation. We certainly make every effort to overcome this problem through borings, geological research, site visits, etc.; but at best owners, engineers and contractors alike are only able to interpolate a relatively small amount of factual data from isolated sections of the project into a forecast of ground conditions for the entire project. In essence this becomes an "educated guessing game" with risk to reward ratios (and subsequently the bid price) in direct relationship to the contractor's confidence in the quality of the guess. In many instances it is economically or physically infeasible to obtain information and of course the total picture is never known until the project is complete. This problem effects the contract format as well as price. The contractor's ability to handle unforseen problems on the project become extremely important as to the project's overall success. The following pages contain an actual case history of a project which affords an excellent example of the entire spectrum of situations resulting from tunnel construction in difficult ground conditions.

Jan 1, 1983

By Neha Shukla, Nikhil Dhawan

The current study examines the extraction of rare-earth elements from trichromatic phosphor of discarded tube lights via baking processes. The Y2O3: Eu3+ (YOX) and BaMgAl10O17: Eu2+ (BAM) phases completely decomposed during acid and alkali baking with > 90% Eu and Y extraction. Prior, selective acid leaching of the YOX phase enhanced the acid baking process at a lower temperature (< 230 ℃). Feed acid baking showed a maximum 87% Tb, 36% La, and 17% Ce extraction at 500 °C, 0.5 h, 1 ml/g H2SO4, and alkali baking yielded 16.1% Tb, 86% La, and 73% Ce at 300 ℃, 0.5 h, 50 wt.% NaOH. The acid baking of the acid-leached phosphor yielded 72% Tb, 95% La, 63% Ce, ~ 95% Y, and Eu extraction at 300 °C, 0.5 h, 1.05 mL/g H2SO4. Lower Tb extraction during the acid baking of acid-leached phosphor can be attributed to the formation of Ba3Tb( PO4)3 and BaTbO3 phases. Insoluble Si3Tb5 phase formation and partial decomposition of CeMgAl11O19: Tb3+ (CMAT) phase in the alkali baking route leads to lower Tb extraction. The acid baking process is suitable for extracting Tb, Eu, and Y, whereas the alkali baking process is suitable for La and Ce. The thermal analysis of phosphor and flux interaction depicts that alkali baking is less energy-intensive than acid baking. In comparison, the one-step acid baking process and the two-step alkali baking process yielded desirable extraction results (87% Tb, total RE (rare earth) 78.5% and 50.4% Tb, total RE 59.3%). The product yield in the acid and alkali baking route of feed, acid-leach phosphor is 36%, 29%, and 39%, 28.2%, respectively, with ~ 98% mixed rare-earth oxide purity.

May 5, 2022

By Don S. McCoy, W. Joseoph Schlitt, Donald B. Swanson

Introduction Contract miners have long played an important role in the minerals industry. Historically, these were individuals who worked as underground miners and were paid by the ton or the day. These hardy types still ply their trade in the industry. However, today the term "contract miner" generally refers to an independent contractor who supplies the people and equipment needed to conduct surface mining operations for an owner or lease holder. At one time or another, contract miners have probably handled virtually every mineral commodity from sand, gravel, and stone quarrying to mining uranium and precious metal ores. In today&apos;s market, though, contract mining appears to be concentrated in just a few areas. These include precious metal mines, various types of solid fuel operations, and reclamation of abandoned mines. This article covers market areas, contract mining organizations and services, and their advantages and disadvantages. Gold and silver mines Although exact figures are not available, contract mining represents a significant element in the precious metals segment of US mining. For gold and silver, the growth in contract mining appears to be paralleling the overall growth in mining activity itself. Nevada is the largest gold producer in the US. The latest available data (1985) on open pit gold/ silver mines is summarized in Table 1 (Nevada Division of Mine Inspection, 1986). These figures show that contractors mined nearly half of the ore in 1985. Total tonnage mined, of course, was much higher for both owners and contractors. Assuming an average stripping ratio of 2.5 to 1, the total daily mining rate for the contractors was more than 145 kt (160,000 st). This translates into a contract mining rate of about 36 Mt/a (40 million stpy) based on 250 operating days a year. This approximate 50-50 split between owner and contractor also appears to hold for the future. Metals Economics Group (1987) published a survey of 51 short-range and 54 long-range precious metal projects being considered throughout the US. Contacts with owners, requests for proposals, and past corporate philosophies all suggest that about 55% of the open pit operations scheduled for the near-term will be contract mined. This represents an estimated 26 kt/d (28.5 stpd) of ore. A similar assessment of the long-term projects indicates that about 12 kt/d (13,000 stpd), or just under 50% of the open pit tonnage will be contract mined. There are several reasons why gold and silver represent such an attractive opportunity for contract miners. One is that many properties are owned or leased by individuals or partnerships that are essentially entrepreneurial. Many of these owners or lease holders have minimal mining experience. They must therefore either rely on contract mining organizations, sell an interest in the project to another mining company that will become the operator, or hire an experienced management team. For about the same reason, junior mining companies also represent good prospects for contracting. This is because most junior companies focus on exploration. They would prefer to spend their generally limited funds on drilling programs. Thus, they tend to minimize additional capital requirements by using contract miners or farming out the property to another mining company. Another good reason for using contract miners is the size of the deposit. Many properties are so small that their reserves will not support the capital expenditures

Jan 12, 1987

By John C. Morrisey, Harold M. Ray

With full production from the Casteel Mine in 1987 The Doe Run Company, a wholly owned subsidiary of the Fluor Corporation, encountered a significant increase of copper and iron to the Viburnum Mill. This major change of the lead, zinc, and copper metal ratios in the ore created circuit problems which adversely affected concentrate quality. Recognizing the problem, the company embarked on a metallurgical research program to include laboratory, pilot plant, and plant testing. The program developed an innovative copper prefloat process which both increased copper recovery and significantly improved concentrate quality. The process was tested and first operated at Doe Run&apos;s Brushy Creek Mill then installed at the Viburnum Mill in 1992. A brief history of development, plant operating data, and other potential applications for the patented processes will be described in the paper.

Jan 1, 1993

By J. Harrison Daniel

Increasing concerns of industrial hygiene and worker health issues and resulting regulatory actions, coupled with continuing advances in mining systems, are placing new burdens on the industry and Federal Government; particularly, mine ventilation departments. More encompassing worker health programs are required to respond to Federal promulgation of regulations and to keep abreast of techno- logical advances in the mining industry. The relationship between the mining industry and Federal agencies involved in rulemaking is presented, along with the rationale of an Industrial Hygiene Management Plan. This plan or strategy focuses on developing partnerships and collaborative research groups to address the controversial health issues facing not only the mining workforce, but our society.

Jan 1, 1993

By B. Samanta

This paper highlights the use of an innovative mine production scheduling scheme for grade-control planning tasks that take into consideration grade-model uncertainty. The scheduling exercise has been carried out with the help of a multiobjective genetic algorithm (MOGa) for the production scheduling operations. The underlying motive behind the use of MOGa has been the generation of a set of pareto optimal solutions to meet the goals of the target-grade specifications for the considered multiple grade attributes. Several new concepts related to MOGa formulation, in particular the mutation operation and the convergence criteria of this algorithm, are proposed in this paper. The modeling of grade uncertainty into the scheduling outputs has also been incorporated through a set of conditional simulated grade maps. The proposed scheme of production scheduling operations has been applied for the grade-control planning operations in an iron ore mine to meet the targeted grade specifications of iron, silica and alumina, and a risk analysis has been performed to this end.

Jan 1, 2013