Search Documents

By A. M. Stone

INTRODUCTION In ore beneficiation one of the simplest methods of mineral concentration is hand picking to remove either the ore or the waste material from a moving table or conveyor belt. Ore Sorting Equipment may be defined as equipment for mechanized picking. This type of equipment has been used successfully over the past thirty years or so to beneficiate ores of various types in particle mesh sizes between 1mm and 200mm.. at throughputs of up to 150 tonnes per hour. In general for ore sorting to be a consideration the ore and the waste material must be well liberated in the feed to the sorter (that is into practically discrete particles of ore and waste). The larger the liberation size the more likely sorting is to be cost effective. Correct selection of ore sorting equipment is most important and often special machine features are developed for an individual application. Sorter performance can be best determined by extensive testwork of representative ore at design tonnage on prototype or preferably on production model sorting machines. ADVANTAGES OF SORTING ORE The four main advantages of sorting ore are: Reduced milling cost. Reduced processing cost. Higher overall recovery. Reduced transportation costs. Reduced Milling Cost With sorters installed the milling plant following the sorter is generally smaller and hence less costly to install and operate as it only has to handle the sorter product. However this benefit is somewhat offset by the increased cost of the screening and washing plant prior to the sorter and the cost of the sorting plant itself. Reduced Processing Cost As there is less material of higher grade presented to the concentrating plant following the sorter, this plant will generally be smaller and less costly to construct and operate than a plant treating the total quantity of material. Higher Overall Recovery The economic recovery is often misunderstood by plant operators when evaluating the advantages of sorters

Jan 1, 1986

Passive seismic monitoring is a useful tool for measuring wave propagation in rock mass in deep underground mining. About 20000 mining ? induced seismic events of a hard rock mine, are identified and investigated. The travel times of source-receiver pairs allow us to demonstrate temporal change in velocity. It was found that the average P wave velocity is about 6000 m/s in the mining regions. Velocity investigations on the data during about three months around the main shocks show a significant decrease of the average seismic wave velocity after the main shocks. The sudden drop of average velocity change after the main shocks implies the creation of new fractures in the rock mass due to the main shocks. Afterward, the average velocity increased to a normal level after a time duration of several days. A reasonable explanation for the post seismic velocity increase is that opened cracks begin to close due to crack healing.

Feb 23, 2014

By Michael C. Stanley

The set of discoveries for a mining district or camp is a reflection of the exploration history. In the western Abitibi greenstone belt of Ontario, future exploration can be guided by a study of statistical trends of known gold deposits. In this area simple trends indicate a strong decrease in the contained quantity of gold discovered through time. Much of this decrease is attributed not to falling mining grades but to smaller tonnages of ore. A plot of the largest discovery in each ten year time period suggests that deposit discoverability is following a size-biased sampling model. Cumulative ounces of discovered gold indicate that an asymptotic value has been reached where exploration is not expected to add significantly to known reserves. This is substantiated by a downward trend in the exploration success ratio of the number of new deposits discovered versus the number of new mineral prospects. The set of discovered deposits reflects a non-random sampling process where size- biased modeling suggests that the largest deposits will be discovered early in the exploration effort. It is the exceptionally large deposit contributing to the observed size-biased distribution. Although this pattern is observed for the western Abitibi the model is complicated by recent, large reserve additions that are attributed to the original discovery. There is present in this area a subtle learning process in exploration leading up to the largest discovery. For comparison a learning model was estimated using cumulative size of discovery per unit of time. This model yielded results consistent with the statistical trends and is thought to be a superior forecast of future discoveries in this region.

Jan 1, 1992

By Bruce W. Cavender

There is a tendency for managers of mining companies to regard the performance of a process plant as essen­tially fixed, with only incremental improvements to be realized by optimizing individual unit operations. However, a number of op­erations management methods are available that will substantially improve plant performance, through both productivity increases and cost reductions. Known collectively as "world-class manufac­turing" techniques, these include total quality control, just-in-time production and inventory management, the systematic develop­ment of innovative plant practices, and progressive management accounting and business control systems. The implementation of these techniques by plant managers and operators will enable the plant's performance to exceed levels that are currently believed to be maximized.

Jan 1, 1993

By Grant P. Cordon

Our subject, "Safety, Legal, and Contracting," is a range of topics which covers a broad spectrum, but is obviously Intended to focus our attention upon certain particular aspects of tunnel problems. These are all fascinating and complex subjects, and others are much more qualified to discuss to discuss the fine points involved. Put after some 45 years' involvement as an inspector, engineer, contracting officer, and especially for the last 22 years as a contractor's estimator and manager, I have developed some strong and definite convictions to share with you. I hope it will serve to get you started thinking. My first tunnel experience was in a soft ground tunnel which was dug by hand, literally. The crown or arch back was taken out, a pebble at a time, by bare hand. The face was constantly breast-boarded, and the mucking was all done by hand shovel. My first rock tunnel was drilled by hand held drifters from the muck pile. Since then, most tunneling techniques have improved greatly. The jumbos, booms, muckers, and moles have taken over many of the back-breaking chores, and reduced the manpower requirements.

Jan 1, 1974

By Pentti Kallio

From the aspect of economic feasibility of mining, ineffective use of expensive mechanization investments is becoming a problem. In many cases, the machinery is in operation only 50 - 60 % of the total working time. The lost time when the machines are idle means a considerable over-investment in machines. The lost time, with LHD equipment in particular, accumulates from the following constituents: - the needs of the person operating the machine trips to the work site, lunch, coffee and other breaks, want for comfort, etc. - deficiencies in the monitoring and control systems for machine operation waiting periods at loading and unloading stations, unnecessary and erroneous actions, inefficient work, etc. - deficiencies in the machine condition monitoring system , and inefficient service and maintenance work The data transfer and computer technology of today provides means for resolving problems in several areas - including the area of underground loading operations. In the paper those areas of automation and data handling are considered which make possible an improvement in the usage and monitoring of LHD equipment. These fields are: remote control of equipment, use of TV cameras and monitors in remote control, locating equipment and data transfer down the mine, measurement of the load and the data storing system, systems for following the condition of the equipment, unmanned operation of equipment.

Jan 1, 1989

By Michael A. Linkous, Mark J. Zdunczyk

Silica in the form of sand and sandstone is one of the most common, and at the same time, unique industrial minerals. Found in every rock type of every geologic age and virtually everywhere in the world, silica is used in products that touch just about every aspect of daily life. Imagine a world in the 1990s without computer chips, fiber optics, or glass, and you have just begun to understand how important silica is to the quality of life we enjoy. The elements silicon (Si) and oxygen (0) comprise roughly 60% of the earth's lithosphere to a depth of about 16 km. The crystal structure of silicon dioxide consists of one atom of silicon bonded to four surrounding atoms of oxygen to form a three-dimensional network of SiO, tetrahedra. This network makes up the mineral quartz (Murphy and Henderson, 1983), the most common detrital mineral in most sandstones. Quartz is also a major constituent of many igneous and metamorphic rocks and is widespread as a siliceous cementing agent in various rock types. Although quartz is common, sandstones, quartzites, and pegmatites and the unconsolidated sediments derived from them that have a silica content high enough and pure enough to meet today's market demands for quality and consistency are not common. USES AND SPECIFICATIONS Silica sand that is mined and processed for industrial uses must conform to the chemical and physical specifications set by customers. In the United States almost half of the silica sand produced is used in the manufacture of glass. Other important products include foundry sand, ground silica, blasting sand, and fracturing sand. Glass Sand Silica is the principal glass-forming oxide in a glass batch. Glass manufacturers develop model specifications for each source of silica sand used. These specifications broadly define the limits and ranges for chemical and physical properties of the sand and are used by the manufacturer in calculating the desired batch mix or formula. Some specifications may be critical to a glassmaker and require very stringent limits on the quantity of impurities in the sand. For example, the total iron oxide content of a batch is extremely crucial when making white or flint glasses (Mills, 1983). Iron is present in almost every raw material used in a glass batch and must be carefully controlled in order to obtain a consistent color in the finished product. It is difficult, however, for a raw material supplier to tightly control the chemistry of a naturally occurring material such as silica sand. To a great extent the commercial quality of a sand is determined by its geologic history. Realizing this, glass producers tailor their model specifications to each source of approved material. In general, a glass company is concerned most about the consistency of raw materials on a day-to-day basis. Soda-lime-silica glass was the earliest type of manmade glass (Baker-Can, 1967) and still accounts for most of the glass manufactured for commercial use today (Mills, 1983). It is relatively easy to melt and shape and is less expensive per ton to produce than most other types of glass (Baker-Can, 1967). Soda-lime-silica glass is used in fabricating containers, flat glass products, incandescent and fluorescent lamps, glass fiber, and many other products. Heavy minerals such as ilmenite, leucoxene, kyanite, and zircon are impurities on which strict limits are placed for a glass batch. Because of their refractory nature they either do not melt or only partially melt, which results in stones or feathers in finished glass. Aluminosilicates such as kyanite also contribute unwanted alumina to the batch as they partially melt. Limits are especially rigid for refractory mineral grains coarser than 0.60 to 0.425 mm (30 to 40 mesh). [Tables 1 and 2] present typical specifications for silica sand used in flat glass and container glass products. The percentages shown represent an average of many companies7 specifications.

Jan 1, 1994

By James E. Lawver

During 1981 the Florida phosphate industry produced more than 43 million metric tons of phosphate rock - about one-third of the entire world production and also generated nearly an equal amount of waste clay and waste clay-sized product that requires dewatering and disposal. The material balance of solids and water for a typical Florida phosphate mining operation is shown in Figure 1. Historically, the industry has impounded clay waste (about 60% below ground and 40% above ground) in earthen dams, often as large as 800 acres and occasionally greater than 60 ft. high. The dams have served the triple purpose of: 1. Dewatering initial 3% solid waste clay for process water re-use. 2. A reservoir system to minimize water discharge from the mining area and to capture and store rainwater thus minimizing deep well pumping requirements. 3. The ultimate densification and storage of waste clay.

Jan 1, 1983

Based on X-ray phase analysis and exploratory experiments, a new technology was developed to recycle multiple valuable elements in spent Al2O3-based catalyst. The experimental results showed that after roasting at 750°C for 30 minutes at an Na2O:Al2O3 mol ratio of 1.2, the leaching recoveries of alumina, vanadium and molybdenum from the spent catalyst were 97.2%, 95.8% and 98.9%, respectively. Vanadium and molybdenum in sodium aluminate solution can be recovered by barium hydroxide and barium aluminate. The precipitation recovery of vanadium and molybdenum was 94.8% and 92.6%, respectively. Al(OH)3 is prepared from sodium aluminate solution using the carbonation decomposition process. The purity of Al2O3 is 99.9% after calcinations, and the recovery of alumina can reach 90.6% in the whole process. The Ni-Co concentrate was leached with sulfuric acid, and a nickel recovery of 98.2% and a cobalt recovery of more than 98.5% were obtained under the experimental condition of 30% (w/w) H2SO4, 80°C, a liquid: solid ratio of 8:1 (by weight), a reaction time of 4 hours and a stirring rate of 800 rpm.

Jan 1, 2007

By Walter C. Jr. Sherman

6.1-SOIL MECHANICS WALTER C. SHERMAN, JR. 6.1.1-DEFINITION Soil mechanics is concerned with the behavior of soils in relation to the design, construction and performance of engineering works. In this context, soils include all uncemented materials, such as, gravels, sands, silts and clays, either naturally or artificially deposited, and, under certain conditions, weakly cemented, badly broken or weathered rocks. Many types of mine wastes have physical properties similar to those of soils and thus are amenable to analysis by the principles of soil mechanics. The principles of soil mechanics are used to solve such problems as the stability of various types of structures with respect to failure of the supporting soils, determination of soil pressures and deformations in the design of foundations and retaining structures, analyses of seepage and under seepage, and stability with respect to sliding of excavated and natural slopes and embankments. 6.1.2--SOIL PROPERTIES Soils are classified on the basis of index properties, such as, particle-size distribution and plasticity characteristics. The Unified Soil Classification System1 used to classify soils for engineering purposes is shown in Table 6-1. Other physical properties important from an engineering standpoint include natural water content, density, permeability, shear strength and compressibility. Physical properties are evaluated on the basis of carefully conducted laboratory tests. Procedures for laboratory testing are presented by Lambe. 2 Soils, either of natural or artificial deposition, are complex three-phase materials consisting of solids, water and gas (usually air or water vapor). One of the most important principles in soil mechanics is based on the concept of effective stress in the soil-water system. A stress, a, applied to a saturated soil is taken partly by the soil particles (effective stress, a'), and partly by the water in the voids (neutral stress or pore water pressure, u,) so that a' = a - u,. Only the effective stress affects the mobilization of frictional resistance between soil particles. In partially saturated soils, the pore-water pressure is negative due to capillary effects. The effective stress relation remains valid for small negative pore pressures, but anomolies arise if the soil is significantly unsaturated. In this case, the pore pressure is commonly assumed as equal to the pore air pressure, u,, so that [ u' = u - u..] 6.1.3--SOIL EXPLORATIONS Soil explorations are carried out by borings or test pits. Hvorslev3 has reviewed procedures and boring requirements, such as, type, depth and spacing employed. In general, soil strata are logged and representative exploratory samples are recovered for classification purposes and for determining the subsurface soil profile, which is constructed utilizing also knowledge of the geology of a site. Undisturbed samples are recovered if the properties of the undisturbed soil are required, as generally is the case. The undisturbed soil sampler consists of a thin-wall tube

Jan 1, 1973

By Deepak Malhotra, Sean Armstrong, Linda Baltich

The economic profitability of any mineral company is dependent upon maximizing mineral recoveries while minimizing costs. The effectiveness of any strategy to meet this objective is dependent upon firstly obtaining quantitative information concerning the steady-state metallurgical balance of the plant, and secondly, how efficiently this information is used to improve/optimize plant performance. This two-step approach can be designated as a "plant audit." Plant audits on a routine basis can be very expensive and time-consuming. Most plants have reduced staffs to cut costs. The remaining staff has to spend time to solve production/operation problems, thereby leaving limited resources (i.e., people, time, and money), for plant auditing. This paper briefly reviews plant auditing categories, and a systematic approach to auditing which has been successfully used at several operations. An example illustrating the use of this approach in gold operations is discussed in this paper.

Jan 1, 1992

By M. J. Blattman

Upon completion of an underground mine design, the planning engineer is faced with a surprisingly complex problem, “What development and mining sequence should be implemented so as to maximize the return on investment?” The problem relates to the scheduling of development headings to access stope production areas in such a way that the most money is made as quickly as possible for as long as possible. The total dollar value of the stopes, the average grade, the total tonnage, nor even the profit margin do not accurately give an indication of the “proper” mining sequence on their own. This paper will outline a method being developed by the author that can create a sequence of events that maximizes the net present value (NPV) of a given development and production design using information already being generated during the design process.

Jan 1, 2003

By C. D. Iles

The philosophy used in designing and writing Duval's Sierrita mine design programs is discussed. The Sierrita Incremental Design system (SID) is reviewed with emphasis on Pushback Extraction Design (PED). FED is a method by which predesigned pushbacks are sequenced into an optimized period-by-period design that can be directly utilized in daily operations as well as intermediate and long range planning. The advantage of SID is that it provides a practical, mineable open pit design. PED is not a theoretical design system; it is in operational use.

Jan 1, 1981

By Robert S. Hendricks

The paper describes the design and operation of a Shaft Boring Machine (SBM). The machine has been developed by The Robbins Company. It is anticipated that the prototype, which will bore shafts in the 6.1 to 7.3 m (20 to 24 ft) size range, will be placed in operation during 1985. This pioneering application of rapid excavation technology is expected to lead to significant improvements in the cost and speed of shaft construction. The technical and economic factors which have limited the employment of Shaft Drilling and which caused unsatisfactory results with earlier attempts at Shaft Boring are reviewed. The design criteria adapted to overcome these problems are discussed. Cost and performance estimates are presented and are compared to conventional sinking methods. Factors that influence the application of the SBM to specific projects are reviewed.

Jan 1, 1985

By D. Kwietnewski

The 4th bore of the Caldecott Tunnel is a 50-ft horseshoe shaped highway tunnel located in the hills east of Oakland, California. Tunnel excavation was mostly completed using one of the world?s largest commercially available roadheaders, a Wirth T3.20. The geologic profile included seven different geologic units, which displayed a range of different behavior with regard to excavation and initial support. Following a brief introduction to the excavation and support methods, this paper will discuss roadheader performance in the various geologic units encountered during excavation. Comments will also be made concerning the relationship between the roadheader method of excavation and observed ground convergence during excavation.

Feb 27, 2013

By Martin L. Smith

Mine waste characterization and risk assessment currently focesses on water quality and largely ignores boththe charteristics of the wastes themselves and how wastes interact with the environment. Characterization of the parameters that control contamination of pore waters and their migration can quantitatively assess risk and remediation strategies in terms of cost effectiveness and risk reduction. Since mine waste characteristics are spatial, geostatistical methods should be used for characterization and assessment. A number of geostatistical methods are reviewed in terms of their application to mine waste sampling, modeling and risk assessment and management.

Jan 1, 1995

A joint research effort by Newmont Gold and Du Pont, working with Kurtis Mooney, of Tri-Combined Resources has developed a new ore-sample bag made of "Tyvek," a spunbonded olefin. "The goal was to find a bag with the best trade-off between efficient draining of moisture, minimal fines loss and compatibility with the conveyor drying process we were developing for our new assay lab," Charles Bucknam, analytical development coordinator for Newmont Metallurgical Services states. None of the available polypropylene, cotton or canvas bags had the needed combination of properties. "Our original tests in 1987 on the plastic bags we had been using showed an average loss of 5.4% of mud sticking to the bags when they were emptied into drying pans. Part of the sample was still in the bag as a residual." Tests on bags of "Tyvek" showed low residuals when the samples were dried in the bags before they were emptied, but about 3% of the fines were lost through the seams. Mooney recommended a new bag design, with fold-over seams.

Jan 1, 1990

By Douglas J. Cork

Biohydrometallurgica1 processes in the areas of coal desulfurization (Hoffman, M.R., et al., 1981) and recovery of metals from metal sulfide ores (Lundgren, D.G. and Malouf E.E., 1983) are well known. In addition other areas of potential interest to the mining industries have been outlined (Spisak, J.F., 1979). For instance, scientists involved in this interdisciplinary field have endeavored to apply microorganisms to the problem of effluent sulfate disposal. This chapter assesses the feasibility of utilizing a particular two stage anaerobic microbial process to convert effluent sulfate to orthorhombic sulfur. Strong emphasis is given to the possibility of substituting this bioprocess for alternative gypsum synthesis and disposal methodologies commonly practiced by companies which emphasize sulfuric acid or ammonium sulfate leaching processes.

Jan 1, 1985

By Patrick J. Ryan, Johann F. Kerl, Angelos N. Findikakis

Introduction Tailings disposal methods used by the mining industry include the use of on-land impoundments, surface and underground mine backfill and marine disposal. The latter method, where applicable and under certain circumstances, can be the most economical and best environmental option. The term marine disposal is used to describe deposition of tailings in the open ocean, coastal waters, fjords and inland lakes. A major element in planning and designing a marine outfall is the assessment of its potential environmental impacts. The nature of the disposed tailings, and the physical, chemical, and biological characteristics of the receiving water body must be carefully assessed prior to deciding whether marine disposal is an acceptable option for a particular project. During the last decade, the North American mining industry has demonstrated a commitment to studying potential adverse environmental impacts of marine tailings disposal and to continue monitoring of the receiving waters. Extensive monitoring programs have been undertaken by Canadian mines. Marine tailings disposal is not used in the United States today. One of the largest U.S. mines proposing to use this option is the Quartz Hill mine of U.S. Borax in Southeastern Alaska. To assure the regulatory agencies and the public of the viability and acceptability of this option, U.S. Borax undertook an extensive program of environmental studies aimed at assessing the impact of marine tailings disposal. This program was part of the feasibility and environmental permitting studies conducted by Bechtel Civil & Minerals, Inc, on behalf of U.S. Borax. Due to the unique nature of the proposed tailings disposal system, a Board of Consultants was established. The Board assisted in planning the modeling and field program and reviewed ongoing work. This paper outlines the basic elements of the marine tailings disposal study program which can be viewed as a prototype for similar studies elsewhere. Background The Quartz Hill molybdenum deposit is located on a knoll in an elevated valley in a mountainous region of southeast Alaska, about 45 miles east of Ketchikan (Figure 1).

Jan 1, 1986

By T. R. A. Davey, J. W. Sherman, B. J. DiSanto, G. Bjorling, G. S. Stacey, J. T. Cullom, R. L. Bird, S. E. Woods, J. C. Blair, Jorma Honkasalo

Most pyrometallurgical processes take place at high temperature with rapid chemical reactions when the elements and compounds are usually liquid or gaseous. Smelting. The classical method of obtaining a metal from its ore or concentrate is to smelt it in a furnace. The initial letter "s" of this word implies that, in addition to the physical process of melting, a chemical change also occurs. This is usually the reduction of metal oxide to metal by carbon or through a series of processes involving oxidation and reduction. Since solid-solid contact would not be sufficient to give a high rate of reaction, most smelting reactions occur by medium of two reactions involving solid-gaseous contact: where M represents a metal. The commonly preferred unit for carrying out these reactions is the blast furnace,1 which is a vertical shaft of refractory brick or water-cooled steel in which lumps of metal oxide and coke are fed at the top, and an air-blast is injected through tuyeres (water-cooled pipes) in the bottom. Molten metal is withdrawn from a pool at the bottom of the furnace, while N2, CO, and CO2 gases leave the top of the furnace, carrying some fine dust or fume with them, which

Jan 1, 1985