Search Documents

By Harold L. Hinds

The refining of precious metals from steel wool cathoodes is completed by one of two methods: 1) By direct fire smelting or: 2) Acid treatment of the cathodes to dissolve the steel wool and then followed by fire smelting. To further the refining of the cathodes, the Miller Process and the Wohlwill Process are used.

Jan 1, 1981

By C. N. Bensley, S. K. Nicol, R. Lamb, G. W. Kidd

Flotation circuits in the metalliferous industry recover high value concentrates from very fine (minus 0.lmm), low grade, slow-floating feeds. Flotation columns acting as final cleaners within these circuits offer the benefits of higher grade concentrates, reduced circuit complexity, improved control and reduced power consumption. By contrast, in the coal industry, these benefits have not been realised, principally because columns are not well suited to the treatment of conventional coal flotation feeds (minus 0.5m). However, this does not imply that columns do not have a place within the coal industry, rather that they must be applied in a role where all the unique advantages of column flotation can be of benefit. The development of a commercial scale column to recover discarded ultrafines from the Riverside preparation plant of BHP-Utah Coal Limited is discussed. Particular emphasis is placed on the column design features pertinent to the recovery of ultrafine coal. Pilot and commercial scale column performances are compared. The results of the commercial scale testwork indicate that a full installation at the 5.5 MTPA Riverside plant would annually recover additional coal worth $US 6.6M.

Jan 1, 1988

By R. R. Klimpel

In this first report, we present a preliminary model based on the simple binary sys¬tem of component B occluded in a matrix of compo¬nent A, for the case where fracture planes can pass with equal ease through A or B. By assuming that the volume fraction of B in AB in the overall matrix is small, which is realistic for many prac¬tical systems, the problem is reduced to a one-¬dimensional treatment which is conceptually easy to understand. The model was programmed for Monte Carlo simulation, and an analytical solution also developed based on the assumption of zero or one mineral fragment per particle. Preliminary ex¬perimental confirmation using a synthetic "mineral¬-host matrix" of known amount and size of B in AB is presented.

Jan 1, 1983

By R. L. Virta

Sixteen companies mined fuller’s earth in 11 states during 2004. Production during 2004, based on a preliminary survey of fuller’s earth producers, was 3.96 Mt (4.3million st) valued at $340 million. This compared with3.6 Mt (3.9 million st) during 2003, valued at $346 million. The 3.96 Mt (4.3 million st) probably includes some crude clay tonnage. And production of finished product probably was closer to 3.2 Mt (3.5 million st) in 2004. Georgia was the leading producer state of attapulgite-type fuller’s earth, followed by Florida. Georgia also was the leading producer state for montmorillonite-type fuller’s earth. It was followed, in descending order, by Mississippi, Missouri, Florida, Virginia, Illinois, California, Tennessee, Kansas and Texas.

Jan 1, 2005

By Frank Littlewood

Research over a period of ten years resulted in the development of an efficient automatic ore feed regulator for mill grinding circuits. The facilities that a large mining company gave the inventor made it possible to develop the control apparatus under actual mill operating conditions. The Littlewood Regulator automatically determines the optimum power input at which a mill should operate, and controls the rate of ore feed to maintain this optimum power for any predetermined operating conditions. It is to be noted that the optimum power varies with many factors such as ball, rod, and mill liner wear, therefore the regulator is designed to automaticall keep itself properly calibrated. To efficiently control the rate of ore feed of a mill grinding circuit the regulator analyzes and interprets all power changes of the mill motor. The critical electrical measurements for this type of control are made possible by a patented device that has the ability to detect and integrate minute changes in power. In ball mill operation the small but significant changes in power serve to select the rate of ore feed in accordance with the rate at which ore accumulation takes place within the mill, and in rod mill operation they serve to select the rate of ore feed in accordance with the degree of rod spread.

Jan 1, 1970

By D. Bogunovic

The U.S. coal mining industry consumes a significant amount of energy, primarily diesel fuel and electricity. The continuous global increase in energy demand, high energy prices, and environmental issues related to carbon dioxide emission represent a substantial challenge for the mining industry. This paper presents a result of research work on development of an integrated data environment system for analysis and control of energy consumption in a surface coal mine. A case study on an operating surface coal mine is carried out to demonstrate the practical application of the developed system. The research work presented here may be used by mining professionals to help provide the answers to the crucial questions of when, where, and how much energy is being used. This developed system represents a framework for efficient management of energy consumption. Key words: surface mining, coal, energy consumption, Information System.

Jan 1, 2009

By G. Kosick, G. Dobby

CEET, an acronym for Comminution Economic Evaluation Tool, was jointly developed by MinnovEX Technologies Inc. and 13 major mining companies for the purpose of designing and predicting the performance of grinding circuits. It fundamentally differs from other methods by using as its’ data set a geostatistically significant population of hardness data distributed across the mine block model. Historically the characterization of an orebody for the purpose of either designing a grinding circuit or predicting the performance of an existing circuit has been done with a relatively limited number of discrete samples. In addition to power selection, shell sizing, and costing for multiple circuit options, CEET also outputs tons per hour, P80, and operating cost on every mining block for subsequent integration back into the block model. This paper will provide an overview of what CEET is and how it works.

Jan 1, 2001

Your thoughts on the current status of the global minerals industries? The global economic, technological, social and political changes of the last two decades of the 20th century resulted in the emergence of a restructured minerals industry. This industry is now based on a new cost-cutting philosophy; utilization of modern technology; productivity gains rather than production tonnages; diversification of mineral markets; and globalization of exploration, mining and processing. Quantity and tons used to be the focus. The emphasis today is on remaining competitive in the marketplace by lowering per-unit production costs as much as possible. What factors and trends will impact the minerals industries in this, the 21st century? A number of parameters will impact minerals operations and shape the future sustainability and growth of the minerals industries. Increased demand for minerals will be accompanied by the demand for technical advancements. We will also see a continued emphasis on health and safety, environmental stewardship, and education and training. Let me elaborate.

Jan 1, 2002

By W. M. Schafer, C. F. Luckay, D. A. King

Monitoring devices have been installed at several mine sites to assess the potential for the development of acid rock drainage (ARD) in waste rock, spent ore and tailings material. In addition, instrumentation has been designed for monitoring changes in water quality in pit lakes. These devices monitor temperature, oxygen, water movement and water chemistry in the waste rock pile. This information can be used to evaluate the current and future ARD risks and the effectiveness of caps and covers. The information can also be used in the design of other reclamation strategies that limit ARD development. The instrumentation includes nested thermistors and oxygen sensing ports, neutron access tubes, heat dissipation units (HDUs) and lysimeters. Many of the monitoring devices can be linked to a data logger and telemetry systems, enabling monitoring data to be downloaded from the office.

Jan 1, 1999

By Donald G. Wieland, James H. Meinholz

INTRODUCTION The Milwaukee, Wisconsin Metropolitan Area provides an ideal opportunity to review the advancement of the art and science of mixed face tunneling in the past 65 years. Although there were earlier tunnel projects in the Milwaukee area, by other agencies, the majority of those driven in the Twentieth Century have been done under contract with the Milwaukee Metropolitan Sewerage District through the agency of the Sewerage Commission of the City of Milwaukee and the Metropolitan Sewerage Commission of the County of Milwaukee. Legal Description of District The Milwaukee Metropolitan Sewerage District was created by the Wisconsin Legislature in 1921 together with the Metropolitan Sewerage Commission of the County of Milwaukee. This concept of subregional wastewater control was an outgrowth of an investigation and report from a commission appointed by the Common Council of the City of Milwaukee in 1909 to study final sewage disposal for the City. In 1911 that Commission, comprised of J. W. Alvord, George C. Whipple and Harrison P. Eddy, recommended that the City construct a water filtration plant, construct a Menomonee River flushing works, expand the intercepting sewer system and, after a thorough study of the then existing and developing methods of sewage treatment, construct a sewage treatment plant. In response to those recommendations, the Wisconsin Legislature, in Chapter 608 of the Laws of 1913, created the Sewerage Commission of the City of Milwaukee. Recognizing that the improvement of surface water quality would require action on a watershed basis, the Legislature, in Chapters 554 and 590. of the Laws of 1921, created the

Jan 1, 1979

By Gennaro Gerald Marino

Vast improvement in methods of design and analysis of the long- term stability of overburden above room and pillar mines is needed. Improved methods are vital for planning and land development and for prediction above existing, presently stable, room and pillar mines. As shown on the flow chart in [Figure 1], the assessment of the long-term stability is an integral part of the site investigation process regarding mitigation of surface damage effects. In Illinois, flat farmlands with subjacent coal reserves cover vast areas. In some of these areas high extraction of the underlying coal layer(s) may not be possible since the resulting surf ace subsidence combined with a pre-existing shallow water table would make the land too wet. Thus recovery of this coal might only be accomplished by room and pillar mining where the ground surface does not subside and the hydraulics of the overburden are not significantly affected.

Jan 1, 1986

By D. D. Misra

Though computer simulation of coal beneficiation has been in use for nearly two decades the models used in the programs for the simulation of the crushing processes concentrate mainly on the size distribution. This paper suggests the use of an empirical equation approximating to the cumulative probability or error function for the simulation of the liberation process in coal crushing. The algorithm outlined here can be incorporated in a computer program already having a size distribution model.

Jan 1, 1989

By J. L. Weaver

The spiraling rate in phosphate rock demand during the period 1957 to 1967 led producers to expect a continuation of a high growth rate. Consequently they expanded production capacity to meet the expected demand. Both the domestic and the world demand has shown little growth over the past three years. Florida producers operating at less than 75% of installed mining capacity, produce all that their markets will absorb. We expect that the nest few years will bring only a slight improvement in this condition. An increased demand in the domestic agricultural market will be partially offset by a continuing erosion in the export market.

Jan 1, 1972

By J. F. T. Agapito

The load carrying capacity of oil shale pillars excavated by conventional blasting, presplit blasting, and mechanical mining is evaluated. The study was based on a comparison of in-situ vertical stresses and fractures obtained from overcoring horizontal holes in the Colony Mine, Piceance Creek Basin, Colorado. Results indicate that conventional blasting causes a zone of damage approximately 3 m (10 ft) thick with low stress distributions. Presplit blasting reduces damage significantly, and increases the load carrying capacity in the 3 m (10 ft) thick zone by 5.93 MPa (860 psi). Mechanical mining causes little or no rock damage, and an increase of 9.83 MPa (1425 psi) in strength in the same 3 m (10 ft) thick zone. An example of pillar design is given showing that the use of presplit blasting and mechanical mining techniques can increase the extraction ratio by at least three and five percent, respectively, as compared to conventional blasting. It is speculated that comparable increases in extraction should also occur due to increases in span dimensions.

Jan 1, 1984

By Hang Yang, Linneas W. Laage

A major concern of mine fires is the heat generated ventilation disturbances which can move products of combustion (POC) through unexpected passageways. Fire emergency planning requires simulation of the interaction of the fire and ventilation system to predict the state of the ventilation system and the subsequent distribution of temperatures and POC. Several computer models were developed by the U.S. Bureau of Mines (USBM) to perform this simulation. The most recent, MFIRE, simulates a mine's ventilation system and its response to altered ventilation parameters such as the development of new mine workings or changes in ventilation control structures, external influence such as varying outside temperatures, and internal influences such as fires. Extensive output allows quantitative analysis of the effects of the proposed alteration to the ventilation system. This paper describes recent USBM research to validate MFIRE's calculation of temperature distribution in an airway due to a mine fire, as temperatures are the most significant source of ventilation disturbances. Fire tests were conducted at the Waldo Mine near Magdalena, NM. From these experiments, temperature profiles were developed as functions of time and distance from the fire and compared with simulations from MFIRE.

Jan 1, 1995

By Mary-Lee Athorn, David A. Barratt

An opportunity to compare the performance of different tunnel boring machines (TBMs) operating in similar rock conditions occurred during the construction of a major water scheme in the UK. The principal objectives of this study were: (i) To collate, analyse and present the data available for the four TBM drives of the Kielder Aquaduct Scheme in terms of the tunnelling system performance and the downtime experienced, particularly where these were influenced or controlled by geotechnical parameters. (ii) To isolate the major sources of machine downtime and highlight those aspects of the tunnelling system that critically affect tunnelling progress rates (iii) To determine, by statistical techniques, relations between TBM performance and rock properties.

Jan 1, 1986

By R. Larry Grayson

A survey of 1250 surface and underground coal mines across the United States was made according to a stratified sampling technique based on national coal districts. A total of 171 responses (13.7% response rate) have been returned and summarized, giving a picture of computer usage in the coal industry. Overall, 63.5% of the respondents use computers, but the percent varied from 100% for large mines to only 44.1% for small mines. As expected, a proliferation of microcomputers has pervaded the industry. Importantly, in spite of the high usage of computers in the industry, sophisticated engineering applications have not yet burgeoned.

Jan 1, 1989

By Frank R. Cappuccitti

This paper will deal with current market trends for sulfide mineral collectors in three distinct parts; the global market for sulfide collectors, collectors as tools to solve mineral processing problems and new collector Research in the 1990's. The global market and manufacturing of sulfide collectors will be detailed as well as the trend towards using increasing amounts of specialty products. The use of Total Quality Concepts for laboratory and plant evaluations of new products will also be discussed. Research in the 1990's for sulfide collectors will need to focus not on the development of new chemical species but on the application of the new technologies that have already been developed.

Jan 1, 1994

By J. A. Burger

Research in the eastern U.S. has shown that productive mine soils and forests can be restored using the following guidelines: (1) cooperation among the mine operator, landowner, and regulatory authority in developing the mining permit; (2) replacing topsoil or creating a desirable medium in which trees are planted; (3) loosely grading non-compacted topsoil; (4) using native and non-competitive domestic ground covers that quickly protect the site; and (5) planting a proper silvicultural mix of crop trees for their commercial value along with nurse trees for wildlife and soil improvement.

Jan 1, 2002

By Kenneth R. Miller

Surface mine equipment operators in the Campbell County region of Wyoming's Powder River Basin have found new ways of solving old problems. Technology, experience, competitive pressures and an increasing grasp of economies of scale have driven mine operators, equipment manufacturers and suppliers to specialization of applications. In economic terms, today's coal price of $4.95/t ($4.50/st) equates to $2.53/t ($2.30/st) in 1980 terms - an incomprehensible value at that time. This article describes some examples of change and adaptation made by Powder River Basin coal operators in overburden stripping equipment and techniques. It focuses on the evolution of the design and use draglines, shovels, trucks, scrapers and dozers.

Jan 1, 1998