Search Documents

By M. C. Williams

The solution of the dynamic population balance model (PBM) of a closed grinding network consisting of a mill, sump, and cyclone is problematic. The fact that the dynamic PBM model equation solution to the Inverse Problem for grinding systems is degenerate or underspecified is demonstrated. Two numerical solution approaches to the Inverse Problem are used. These are: 1) providing additional constraints on breakage selection functions or 2) performing the Arbiter-Bhrany (or other) normalization of the selection functions. Actual experimental anthracite batch grinding data is used to demonstrate the non-unique functionality of the batch dynamic mill selection and breakage functions for a real physical system. The Levenberg-Marquardt algorithm for systems of constrained non-linear equations is used to solve the batch dynamic PBM grinding equations to obtain the grinding selection and breakage rate functions. Different solutions to the same PBM transport equations are provided. The mill, sump and hydrocyclone were modeled as a CSTR operating at various retention times. Batch dynamic PBM data was used to provide the mill kinetic and breakage selection function data. Two different solutions were obtained depending on the numerical solution approach. The severity of the non-uniqueness problem for dynamic grinding is demonstrated. Each solution approach to a dynamic PBM with transport, while giving the same prediction for a single batch grinding time, gives different solutions or predictions for mill composition for other grinding times. This fact makes dynamic nodal analysis and control problematic. The fact that the constraint solution approach gives a solution may suggest that normalization for closed networks is not necessary. Differences in solutions to the PBM cannot be excused away by inaccuracies in the data used to model the grinding phenomenon.

Jan 1, 1995

By H. C. Juvkam-Wold

The design of an aquifer depressurization system is discussed. The system uses a number of wells surrounding a mine shaft to reduce the aquifer pressure in the vicinity of the shaft. The effect of various parameters such as number of wells, wellbore diameter, time and well location is discussed. It is concluded that, with a properly designed depressurization system, the aquifer pressure and the water inflow rate to the shaft may be reduced to less than 15X of their potential values in the absence of wells

Jan 1, 1980

By A. Kepeski

Cement industry relies heavily on the control of large volume of raw materials in the proximity of plant operations for clinker and cement manufacturing. These mineral resources are perhaps considered as ?low-profile? (mostly comprise limestone's, clays, marls and sands), but their availability, accessibility and suitability ? the later with respect to chemistry, mineralogical and physical characters ? are factors of paramount importance and may largely affect production cost and plant productivity. The combination of scarcity of good quality raw materials deposits and the growing environmental concerns have challenged the cement producers towards sustainability and the responsible exploitation of natural resources. In open pit mining and quarrying, the evaluation of mineral resources vs. handling of the non-usable overburden and other off-spec materials directly affects the medium to long-term production planning, quality control practices and environmental management. It is a general trend for many cement producers and a usual case for a number of Titan Cement plants worldwide, that redesign of quarry pits is necessary not only for stability purposes but also as a result of environmental constraints and emerging issues. The material reserves then have to be re-evaluated in the light of the new final pit design, safety distances from houses, other infrastructure and Law restrictions and according to criteria of safety of operations, reduction of environmental impacts, pit optimisation and proper future reclamation. The paper discusses the case of three active quarries of Usje Cement Plant, in Skopje (Macedonia), namely Usje (marl), Goverlevo (lime-stone) and Ljubosh (sand), where a large campaign of redesign and evaluation of recoverable reserves and the needs in rehabilitation took place in 2004. Technical and environmental issues and criteria are presented in the form of master plans and the highlights of the first attempts to propose and apply a reclamation scheme are discussed, by also examining alternative solutions for each quarry area. Finally, the 2005 progress in applying changes to the design of benches and pit layout, as well as experiences gained, are discussed.

Jan 1, 2005

By Cleophus Short

[Of the many occupations in and about the coal mines, those of the haulage crews are among the most hazardous. Statistics ship that the second greatest number of fatalities about the coal mines occur during haulage ion and through the use or misuse of haulage equipment. During the five year period between January 1, 1957 and January 1, 1962, the m stone mine had a. Sack haulage frequency of 4098 and mined 3, 541,939 toads per haulage fatality. Coal mire haulage is similar in respects to railroading. We gee very serious consideration to the instillation of tack and to the selection of the haulage crews. In doing this, we are attempting to have our coal mine haulage as. Safe as that of the railroads.]

Jan 1, 1963

By J. Loeb, R. Ramanathan, P. Cameron

All mining operations, including iron ore, maintain a focus of continuous improvement and asset optimisation in their operations. As all the operations in the Mine-to-Mill value chain are inter-dependent, available technologies that address efficiencies across the value chain are once again in the spotlight as companies are driven to improve productivity and maximise mine site profits to increase return on capital invested. Core to continuous improvement is the need to understand the baseline and the impact of changes to the process. In this paper, we discuss some of the key attributes in the mine to mill process, including their influence on productivity and cost, the need for direct measurement and areas where they should be applied. Many initiatives can be considered to improve mine to mill processes. Mining operations are planned and executed based on designs and models to achieve the operation’s objectives. However, there are many variables in the different parts of the value chain, such as blasting, material handling, crushing and screening. Measurement of the key attributes establishes the baseline for Mine to Mill (or Pit to Plant) performance which is necessary to understand the impact of any proposed improvements to the process design and execution and to monitor the outcomes on an ongoing basis to sustain the improvements that have been implemented. We have focused this paper on two types of measurement – blast movement and particle size of materials through the mine to mill process. Several innovative technologies are already available to measure these attributes and assist operations improve productivity and mine site profits.

Mar 2, 2022

By A. Kyriazopoulos

Quarrying is an important activity as it significantly contributes to the economy of a country. This activity presupposes the destruction of the natural vegetation, the removal of the surface soil and deposition of inactive materials. The lack of fertile soil in these disturbed areas is usually a problem for the plant cover establishment. The purpose of this study was to investigate the potential of the establishment of ten herbaceous plant species to inactive quarries with the use of limited amount of fertile soil. The research was conducted in the area of the quarries of the cement manufacture company ?TITAN?, Thessaloniki, Greece. On a terrace of one of the quarries, a 2 cm layer of fertile soil was placed. In early October 2007, the herbaceous species, Lolium rigidum, Festuca arundinacea, Bromus inermis, Agropyrum desertorum, Phalaris aquatica, Dactylis glomerata, Medicago sativa, Medicago lupulina, Sanguisorba minor and Phacelia tanacetifolia, were seeded separately. The first results indicated that among the tested species Dactylis glomerata, Festuca arundinacea and Phacelia tanacetifolia had the highest establishment capability.

Jan 1, 2008

By Tristan Joubert, Fabio Panella, LiLing Chen, Yung Loo, Michael Devriendt, Nasir Qureshi, Ahmad Ali

Tunnel inspections have traditionally been carried out manually by inspectors writing up observations and taking photos of defects. The results from the inspection and the defects observed are dependent upon the rigor of the inspectors and may be subject to repeatability and consistency issues and is often time consuming with elevated health and safety risks. This paper will discuss work that is being carried out in developing and implementing an innovative hardware and software solution integrating machine learning to automate the process of capturing objective tunnel condition information, offering cost and programme savings as well as health and safety improvements

Jun 13, 2023

By John W. Greene

For the past two years, Tenneco Minerals Company has been evaluating a refractory, pyritic, carbonaceous gold deposit, Results from agitated biological oxidation reactor tests show the gold extraction was increased from 15 to 90 percent using microbial oxidation, Also, no preg robbing occurred after complete microbial oxidation. Three column biological oxidation tests were then initiated on minus 1/2 inch ore. Biological oxidation was discontinued in two of the three tests, These columns then were leached with cyanide. The maximum gold recovery was 62 percent. No preg robbing was observed,

Jan 1, 1990

By R. Krishna, L. A. Kumar

The paper suggests a new empirical model for predicting mining subsidence. The parameters considered are Lithological Factor, which in this context meant percentage of sandstone, Rock Mass Factor (depending upon the RQD value of drill-hole cores), width: depth ratio and percentage extraction of coal. More than 250 drill-hole cores from seven longwall panels and 11 bord-and pillar (room-and-pillar) workings were analyzed from an extensive data bank of Singareni Collieries Company Ltd. (S.C.Co.), Andhra Pradesh, India. Excellent subsidence agreement was found with the suggested model.

Jan 1, 1993

By Rolf Lange

Introduction The Harzwasserwerke, a public body of the Federal State of Lower Saxony, supplies drinking water to an area bordered by Braunschweig, Bremen, the Northern and the Western edges of the Harz-Mountains. From the very beginning in 1928, the Harzwasserwerke have been systematically constructing reservoirs in the western Harz which have the function of collecting and storing the frequently occuring flood waters as well as providing drinking water. The Grane-Reservoir with a capacity of 45 Million cu.m., the last of the big reservoirs, was built in 1968-1970. A system of connecting tunnels effectively enlarges the natural catchment area of this reservoir and the surplus waters of the Oker and Radau valleys - where floods occur particularly during the spring - are being conducted to the reservoir. By building the 4.800 m long "Radau-Tunnel", the waters of the Radau valley will now also be used more efficiently and its surplus waters will pass to the Grane Reservoir via this new tunnel and the Oker-Grane-Tunnel which was finished in 1970. The Project The Radaustollen has been planned and put out to tender by the Harzwasserwerke as a conventional "Freispiegelstollen". The horseshoe profile has a cross-section of 8 m2. Lining was required only in disturbed rock areas; lining of the whole tunnel was not necessary. The gradient of the tunnel is 4 % 0 rising = 25 m over the total length of 4.800 m.

Jan 1, 1979

By R. Karl Zipf

Highwall mining is an important surface coal mining method, and it may account for approximately 4% of total U.S. coal production. Highwall stability is the major ground control related safety concern. Ground control plans for highwall mining should specify hole width, web pillar width, barrier pillar width and number of holes between barriers. This paper offers simple design charts for these parameters aimed at providing “ball park” checks. Web pillars containing pre-existing auger holes are analyzed and a design chart for estimating their minimum width is also presented. Finally, close proximity multiple seam highwall mining, which may have caused several serious highwall failures, is analyzed. Web and barrier pillar recommendations for this special situation are presented.

Jan 1, 2005

By J. L. Francke

This paper describes the practices and methods used in a study of Time Domain Reflectometry (TDR) as an inexpensive deformation monitoring tool in underground excavations at the Waste Isolation Pilot Plant (WIPP). The WIPP is being developed near Carlsbad, New Mexico, for the disposal of transuranic nuclear wastes in bedded salt 655 m (2 150 ft) below the surface. Data collected from WIPP geomechanical monitoring are used to characterize conditions, confirm design assumptions, and understand and predict the performance of the deep salt excavation. The geomechanical monitoring program encompasses numerous geomechanical monitoring techniques ranging from inspection of observation boreholes to advanced radar surveys. In 1989 TDR was introduced as a monitoring tool with the installation of 12.7 mm (0.5 in) diameter TDR cables in the underground excavations. In 1993, a new TDR system was installed in a separate location. Based on experience with the previous installation, enhancements were implemented into the new TDR system that: 1.) extended the period of performance by increasing cable diameter to 22.2 mm (0.875 in), 2.) increased accuracy in locating areas of deformation by aligning cables with nearby observation boreholes, and 3.) improved data acquisition and analyses using a standard laptop computer, eliminating the chart recorder previously used. In summary, the results of a correlation between the TDR signatures to nearby observation boreholes and geomechanical instrumentation will be presented.

Jan 1, 1996

By L. E. Eary, Andy Davis

The evolution of pit lake water quality depends on the lithology and hydrologic characteristics of the ultimate pit surface, the availability of buffering capacity in the wall rock vs. oxidizable sulfide content, the alkalinity of recharging groundwater and the evapo-concentrative characteristics of the system. This paper assesses the geochemistry of 11 existing pit lakes, ranging from the acid Red Hill and Berkeley pit lakes (pH 2.6 to 2.8) to the alkaline Yerington pit lake (pH 8.45). Predicted pit lake chemistry is similar to that in existing pits, with long-term chemistry lying on a geochemical continuum between end members that consist of influent calcium bicarbonate groundwater and naturally occurring sulfate-rich evaporite playa lakes.

Jan 1, 1998

By Tim Haldane

Cyanide consumption at the Gold Fields Operating Company Mesquite Mine has shown a steady decline since the heap leach operation started up in 1986. A series of solution strength changes and equipment design improvements have resulted in a reduction of sodium cyanide consumption from peak levels above 1.0 pounds NaCN per ton of ore in 1986 to current levels at 0.15 - 0.20 pounds NaCN per ton of ore. Aside from the obvious cost benefits associated with this reagent consumption reduction, the property has also enjoyed environmental benefits which go hand-in-hand with these cost savings.

Jan 1, 1990

By Ray Brainard

The subsurface investigation for the Reach 4 Tunnel was expected to be completed in a single phase. This assumed that data from two nearby previous tunnels, combined with limited new subsurface information and surface mapping would be sufficient to characterize the rock behavior. Unforeseen rock conditions and complex faulting led to the recommendation for a second phase. This decision was not reached easily, as much of the follow-on work required helicopter support, and associated costs. The second phase of drilling found significantly more variability than the first phase and led to a very different and better understanding of the geologic and geotechnical conditions, and rock characterization.

By Meng Wang

"In this study, multiple methods that include geological surveying, laboratory studies, and numerical modeling have been used to study the deformation characteristics of a “deep inclined rock roadway with weak planes” (DIRRWP). Failure of the DIRRWP was found to be triggered initially by the shearing of the rock near the weak plane. The movement of the failed rock resulted in reduced confinement of the deeper rocks, and causing the failure of the supporting units and the severe deformation of the surrounding rocks. Hence, it is concluded that DIRRWP stability is affected predominantly by rocks near the weak plane. Corresponding control strategies for DIRRWP deformation were proposed: (1) greater support intensity is necessary to maintain the stability of the whole DIRRWP; (2) additional support is needed for rocks near the weak plane to reduce the potential of failure; (3) to increase the bearing capacity of the floor strata, as the floor needs to be supported; and (4) a supplementary support technique should be considered for cases of large deformation. The case study presented here indicates that the proposed control strategies can significantly reduce the potential of failure in rocks near the weak plane, thus preventing severe deformation of the DIRRWP.INTRODUCTIONAs shallow seams are mined out, the cover depths in most Chinese coalmines have become increasingly greater. Deep cover in a coalmine is considered to occur when the cover depth exceeds 800 m (Sun, Chen, and Miao, 2018). The loading and failure behavior of rocks in a deep cover setting are quite different from those in a shallow cover setting owing to the increase in in-situ stress, temperature, and hyperosmosis (Lobanova, 2008; Zhang et al., 2013). For instance, experience shows that bulking and dilating deformation in deep roadways is much greater than that which occurs in shallow roadways (Hou and Yang, 2018; Zhang et al., 2016). In addition, anisotropic behavior and thickness deviation of coal measure rocks, combined with the appearance of weak planes (e.g., faults, joints, and coal cleats) in coal and/or rocks, can significantly affect the stability of an underground roadway (Ghazvinian et al., 2013; Sun, Chen, and Miao, 2018). The presence of weak planes can significantly complicate displacement and stress transmission in nearby rocks. Additionally, tensile, compressive, and/or shearing failure in rocks near weak planes can be easily caused by high in-situ stresses in deep roadways; such failures may lead to further severe deformation of the surrounding rocks, resulting in roof falls and rib spalling (Kamata and Mashimo 2001; Wu, Ohnishi, and Nishiyama, 2004). A typical failure of the so-called “deep inclined rock roadway with weak planes” (DIRRWP) is shown in Figure 1. Severe deformation can be found near the weak plane. In this study, a plane or thin layer of rock/coal parting that can significantly reduce the strength of the surrounding rocks—and thus affect roadway stability—is defined as the weak plane."

Jan 1, 2019

By N. Magdalinovic

This paper analyzes the basic elements important for sustainable development in the sphere of metal mineral raw materials and offers one of the possible ways of defining the index of sustainable development.

Jan 1, 2007

By Arafat Ghosheh, Yousuf Abu-Rish, Darwish Amara, Mohammed Baderkhan

The Jordan Phosphate Mines Company is one of the world's major phosphate rock and phosphatic fertilizers producers (the second largest phosphate rock exporter), with ore reserves exceeding 2 billion tonnes, mainly located in the Eshidiya area. The Eshidiya phosphate deposits, 120 km north-east of Aqaba, are of sedimentary origin (as are all phosphate ore in Jordan). Three exploitable beds (Al, A2, and A3) with variable content of P205, CaO, SiO2, etc., are processed in order to produce 68-70,73-75, and 75-77% TCP grades. The A3 bed, which is characterized as the most siliceous containing 40-48% TCP, requires physical beneficiation using wet scrubbing, screening, and desliming by hydrocylone, followed by anionic conventional flotation to achieve 75- 77% TCP grade. For the last 15 years extensive laboratory and pilot tests (including physical, chemical, and mineralogical studies) were carried out. After operating the industrial plant, certain modifications were deemed necessary to adjust the operational parameters and the final flowsheet, which was followed to obtain the targeted quantity and quality of concentrate.

Jan 1, 1999

By Donald P. Schlick

Gentlemen, today I would like to talk to you about metal and nonmetal mine health and safety--past, present and future. Briefly, I will comment on the past because it is important to an understanding of our present activity and our plans for the future. Federal inspection of noncoal mines was not authorized until 1966, when congress passed the federal metal and nonmetal mine health and safety act; public law 89-577, with the passage of this act, the federal inspector, for the first time, had the delegated authority and responsibility to enforce health and safety regulations designed to prevent personal injuries and occupational diseases, the new law also provided for the education and training of our miners; assistance to the operator through the transmission of technical and scientific information and assistance and equally important, the law made provision for state participation in the congressional mandate to prevent injuries and save lives in the mineral industry, Before I tell you about our program and our future plans, I want you to know that I am here to listen as well as to talk! In my view, the only kind of communication that is meaningful is two-way communication. Our nationwide progress in metal and nonmetal mine health and safety during 1972 cannot be measured in reduced fatalities or injuries. The unforeseen tragedy that took pace in Kellogg, Idaho, in may of last year mode that almost a certainty.

Jan 1, 1973

By A. J. Richardson

Before the development of the underground stoping and mining costs can be considered, certain facts about the ore body, the proposed mine, markets, etc., must be known or determined. In the case to be studied, the zinc-lead mineralization occurred with a narrow vertically dipping structure of undetermined length and vertical extent. Exploration completed to date has revealed 6.5 mil¬lion st t of proven reserves. A further 820,000 st of in¬dicated reserves has been outlined and this tonnage is considered capable of being expanded by a factor of approximately four after more detailed drilling. After studying the market conditions and completing a very preliminary feasibility study, it was decided that production would be 730,000 stpy (or 2000 stpd) of ore. First year production would be at the rate of 1500 stpd. The main design criteria for the selection of the min¬ing methods are minimizing surface subsidence, maxi¬mum recovery of the ore body, maximum degree of grade control, maximum productivity, and safe working conditions. Two basic extraction systems are considered capable of meeting these requirements: mechanized cut¬and-fill stoping and sublevel long-hole stoping with filling. The primary development system of the mine has been designed to give maximum flexibility in stoping systems and layout and to permit changes if considered necessary as a consequence of actual production ex¬perience. At the present time, access to the mine is by a circu¬lar concrete lined vertical shaft, 16 ft diam, sunk to a depth of 1380 ft. Two exploration levels have been driven within the ore zone at depths of 165 and 1246 ft below the surface outcrop. The development to date had the objective of sampling the mineralization and produc¬ing detailed information on the outline of the ore body and the distribution and controls of zinc and lead values. In an attempt to satisfy the basic design criteria for the mine, it was decided that production would be best achieved by a combination of 40% sublevel long-hole stoping and 60% cut-and-fill mining. Costs of exploration and capital development of per¬manent underground facilities are normally written off over the life of a mine. Production expenditures, on the other hand, are of a temporary nature and are normally charged as and when incurred as an operating expense. Reasonably accurate predictions of mine production costs can be built up from engineering design and estimates of individual mine activities for ultimate inclusion in the comprehen¬sive data required for financial decision making. The simulated operations can be costed on a detailed basis in the form of a monthly operating budget. The budget format can be generalized or detailed, depending upon the scope of the project. However, ex¬perience suggests that a fairly detailed format has the advantage of assuring that all significant cost items are included. For underground costing it is suggested that the budget structure include five major cost centers (i.e. development, diamond drilling, ore extraction, hoisting/ transportation, and general mine expense). These in turn are detailed under numerous subheadings. The mechanism for compiling an operating budget will be illustrated. Because of its relative simplicity, ore extraction under sublevel long-hole stoping has been chosen for illustration. All other activities, simple or complex, can be estimated in similar fashion. BLOCK AND STOPE DEVELOPMENT Long-hole blocks, used where advantageous, will be up to 250 ft in height, depending upon the vertical con¬tinuity of the mineralization, and approximately 300 ft long. Drawpoints will be at 36-ft intervals and serviced by loading crosscuts driven from a footwall drift parallel to and close to the ore zone. Pillars between the stopes will be 50 ft wide. Stopes will be drilled off with vertical rings of blastholes drilled from sublevels approximately 60 ft apart vertically. This drilling will be done by percussion drilling machines (31/2 in.) mounted on a trackless drilling rig. Load¬haul-dump (LHD) equipment will be used to move broken ore from the drawpoints to the orepass connecting to rail haulage systems. On completion, long-hole stopes will be backfilled to prevent caving and to facili¬tate later pillar removal. From a planned stope layout, a forecast of produc¬tion and development is made in Table 1. Table 1. Block Tonnage and Stope Development Quantity Ore Waste Total ore block 375,000 st 2 stopes 310,000 st 1 pillar 65,000 st Access crosscuts, 4 at 100 ft 400 ft Drill sublevel drifts, 6 at 300 ft 1800 ft Stope raises, 3 at 250 ft 750 ft Undercut sublevel drifts, 2 at 300 ft 600 ft Loadout crosscuts at 35-ft intervals 550 ft 100 ft 3300 ft 500 ft Total development footage 3800 ft Tons per ft of development 987 st

Jan 1, 1982