Search Documents

By Tedd B. Bodimer

Why complicate an already complex machine such as a continuous miner by adding roof drills? Immediate permanent roof support is an immediate thought of the mining engineer just as elimination of frequent time-consuming places changes is a thought of the methods engineer. The realization of those two objectives has the potential for improved safety with increased production is the thought of the general manager. Miner-Bolters Used a Generation Ago These are not new thoughts as the 1CM continous miner equipped with two integral roof drills was introduced twenty-five years ago. Approximately two hundred of these machines were sold in the next five years for use in medium and high seam operations. The 1CM miner chassis that remained stationary in the center of an entry or room while the ripper bar was swung and sumped hydraulically provided an ideal platform for mounting two roof drills that could be operated during the continuous miner's production cycle. Two roof bolts could normally be installed in less time than required for the mining cycle. A typical roof drill unit is shown in Figure I.

Jan 1, 1981

By Satid Therdkiattikul, Donald A. Dahlstrom

Many gold ores are known to be refractory so that conventional cyanide processing will result in serious losses of gold and silver values. A significant percentage of these refractory ores contain aresenopyrite and the gold and silver is usually encapsulated within this matrix as well as the pyrite matrix. Normally the values can be recovered as flotation concentrates because of the sulfide compounds with recoveries of over 90% and at very good grades. In order to free the gold and silver, the sulfide matrix must be destroyed. This can presently be achieved by (1) pressure­temperature leaching (2) roasting and (3) bacterial leaching. All of them have advantages and disadvantages as well as an obviously increased cost for the each processing method. However, the increased gold and silver recovery should and must more than offset this cost. It is believed that gold recovery should be well over 90% from the concentrate so that overall recovery from the ore should be in the 90-95% region. All three processes must consider pollution control of both sulfur and arsenic to prevent contamination of air, water or land through improper waste disposal. This paper will concern only bacterial leaching and its necessary control of effluents and solids. Sulfur does not appear to be a problem as the element is oxidized to sulfate and is precipitated with an acceptable solubility. Other important improvements that must be controlled are arsenic and iron which are present as significant values (1-12 g/1 of arsenic, 20-40 g/1 of iron). In addition much smaller values of base metals, aluminum and magnesium can be present as well as other elements depending on the ore and these must be low enough after treatment to meet EPA regulations.

Jan 1, 1993

By Joseph F. Shirley

Introduction Inorganic depressants are chemicals added to the froth flotation process to maintain or produce hydrophylic surfaces on one or more minerals so they will remain in the pulp rather than attach to the air bubbles. Whether a depressant will be effective in depressing a given mineral depends on how it is used and the environment in which it is used. Some depressants must be added and conditioned into the pulp before the collector is added. Other depressants can be added in the presence of previously added collectors and effectively depress the desired minerals. Often the concentration of depressant relative to the collector concentration is critical to making an economic separation. It should be noted that some depressants will only work when specific collectors have been used. Some reagents such as sulfuric acid and hydrogen peroxide essentially act as depressants by altering the previously added collectors so that they are no longer effective. Some depressants such as sodium ferrocyanide are only effective in a very limited pH range and an essentially collector free environment. Major Depressants CaO Milk of Lime is by far the most used depressant both in tonnage and dollar value. Although it is most commonly listed as a pH modifier, it is also an important depressant for pyrite in copper and copper molybdenite flotation plants. Although a simple pH adjustment will often depress pyrite, there are times when grinding with fresh milk of lime is required to obtain optimum depression. Lime is also a molybdenite and gold depressant. NaSH Sodium hydrosulfide is by far the most commonly used reagent to depress copper and iron sulfide minerals in by-product molybdenite flotation plants. NaSH also depresses gold, silver sulfides and silver chloride. ZnSO4 Zinc sulfate is commonly used to depress sphalerite in lead-zinc and copper-lead- zinc flotation plants. It has also been used to effectively depress talc in by-product molybdenite circuits at a pH of 6.5.

Jan 1, 1986

By Robert E. Kirby

The potash mine and refinery of AMAX Chemical Corporation is located 26 miles east of Carlsbad on the north end of the potash producing areas. This property was developed between 1949-1952 and production of muriate began in August 1952. Two shafts, located 400 feet apart, were sunk to the ore zone 900 feet below the surface. A 15-foot diameter ore hoisting shaft equipped with a 1000-ton ore pocket, crusher and automatic skip loading equipment plus a 20-foot diameter service shaft with a curtain wall for exhausting air were provided. Sylvinite production to date has been from the first ore zone, stratigraphically, the lowest of ten identified mineralized zones in the salt section. This first ore zone has been the top producer of Muriate of Potash over the years. In our area we do have some very marginal mineralization in the third ore zone some 35 feet above the first. We have not mined from this seam as yet but we are investigating the economics very closely with access slopes and an experimental mining panel. Our ore seam is generally flat lying but does have local gentle rolling with grades from 2% to 5%. The mine was designed and developed from the beginning with conventional mining practices and rail haulage from the mining section to the ore pocket. As mining progressed in the early years, production increased from less than one million tons annually to a maximum of 3,935,000 tons in 1964. Efficiency also kept pace with the increasing production and continually improved until the efficiency of the production crews reached an average of 100.3 tons per manshift in 1964.

Jan 1, 1974

By Joseph W. Leonard

Much progress has been made in the application of geostatistics to hard rock ore deposits.1,2,3 4,8 Progress in the application of geostatistics to coal deposits has developed over a period of time out of hard rock technology.5,7 Exploratory drilling in many hard rock deposits is frequently significantly more productive than exploratory drilling in coal deposits. For example, hundreds of feet of drilling and/or many drill setups are frequently necessary to obtain a few samples from a typical 4 to 6 foot thick coal seam. With hard rock deposits, which are frequently thick or volumetric, less drilling dead work is involved in sampling the deposit. To produce a variogram, which is the basic element needed for geostatistical analysis, a few well positioned holes drilled into a hard rock deposit where the core(s) can be divided into many sections can produce a detailed variogram. To produce a similar type variogram in coal, it is necessary to drill many dozens of holes with much of the core length consisting of overburden data which is frequently of only secondary importance. To apply geostatistics to coal, not only are many separate sample sites needed, but frequently a problem exists in that the interval distance between samples cannot be controlled with the ease that hard rock drilling intervals can be controlled where it is only necessary to cut core segments according to some preassigned interval of distance. Because the uses of existing coal deposit samples are frequently handicapped by irregular sample distances and lack of sampling density along certain directions needed for the development of variograms, the application of geostatistics to coal deposits frequently does not proceed with the same efficiency and rapidity as when these techniques are applied to ore deposits. Grid-fitting was developed by the writers, as a logical and evolutionary improvement over the long and successful application of geostatistics to coal seams.6,9 Grid-fitting combines the trending of variance as well as other aspects of probability theory to optimize informational yields from the commonly less productive data derived from coal exploratory programs. Grid-fitting is basically a technique where a hypothesis involving numerous grid patterns, where each pattern is of a given geometry, size and direction is repeatedly matched against actual sample data to determine which match results in the closest fit of the hypothesis to the data. To determine the closest fit, a special index known as a selectivity index was developed. The selectivity index is basically the product of the mean and variance of the variances contained within each of the grids. hence, if SI is the selectivity index then [SI = Xs E (S i - Xs) /N] where [X]s is the mean of individual grid variances Si2 for any pattern of given geometry, direction and size.

Jan 1, 1984

The 2012 North American Tunneling (NAT) conference is expected to attract more than 800 tunneling and underground construction professionals. But don?t let the North American part of the meeting?s title fool you. Many of the attendees will come from all over the world. The meeting is scheduled for June 24-27 at the JW Marriott Indianapolis Hotel in Indianapolis, IN. In addition to two and a half days of technical programming, the accompanying exhibit has attracted 116 exhibitors in 140 booths. And the conference will include short courses, a field trip and plenty of social activities that will give attendees the opportunity to catch up with each other.

Jan 1, 2012

By D. K. Grubbs

Anorthosite is an abundant, domestic source of alumina with reserves in individual deposits ranging from a few billion to hundreds of billions of tons. While anorthosite contains less alumina than does kaolinite, its CaO and Na20 contents are significantly higher (Figure 1). Alumina can be produced from anorthosite by alkaline, soda-lime sinter or acid processes. CaO and Na20 are advantageous because they are reactants consumed in alkaline processes. Acid processes require high calcium plagioclase feldspars (bytownite-anorthite) to obtain high alumina extraction because the lower calcium plagioclase feldspars (andesine-labradorite) are not as readily dissolved during digestion. The layered Raggedy Mountain Gabbro group in the Wichita complex in southwest Oklahoma is a high calcium anorthosite that could be processed by acid, sinter, or alkaline methods. Chemical grade limestone in the Arbuckle Group is located within 45 km of the anorthosite (Figure 2).

Jan 1, 1980

By Prakash M. . P. E. Donde

1. INTRODUCTION The Washington Metropolitan Area Transit Authority (WMATA) has often taken a leading role in introducing innovative construction technologies to build its transit system. Most recently, Contract Section E-5a, which included Fort Totten Station and Tunnels was constructed utilizing the New Austrian Tunneling Method (NATM) in soft ground. Along with the station and tunnels, two permanent shafts were also constructed in soft ground employing the NATM technique. This project is located within the District of Columbia on the Greenbelt Route. The subject of this paper is to discuss the unique method of construction of these two shafts, and explore the benefits of applying the NATM technique to the construction of deep shafts. The design of the shafts was performed jointly by Jenny Engineering Corporation of Springfield, New Jersey, and Mayreder Consult of Linz, Austria. The designers also provided construction support services and a resident NATM expert at the site during construction. The construction of the project started in April 1988 by a joint venture of Mergentime Corporation and H. T. Construction, a subsidiary of Hochtief Company from Germany. This $48.7 million construction project has been completed. 2. SUBSURFACE CONDITIONS The two NATM shafts are located primarily in Cretaceous-age deposits that are over 100 million years old. These deposits are intermixed and lenticular in nature

Jan 1, 1993

By L. H. E. Weyher

Minerals beneficiation commonly requires initial crushing and grinding so that the mineral phase we seek to concentrate is adequately liberated to obtain a product of specified grade at optimum recovery. To some degree this also is true for coal preparation. In the comminution process we liberate not only the product but also the tailings phase. The true objective is, therefor, to eliminate from the comminution circuit whatever particulate matter has reached specified liberation, regardless of whether the particle is product or tailings material. Overgrinding either of the two phases ties up mill capacity and usually also burdens the downstream processing steps by increasing costs or decreasing recovery, or both. In view of this situation, one would expect concentration steps to be commonly incorporated into the cominution circuit. The reasons this is not done may vary, but probably include the desire to utilize large scale unit operations, e.g., large mills, in conjunction with very simple processes. Hydrocyclones have satisfied this desire but may not always be employed for the right reasons. Hydrocyclones are indeed simple. They also are rugged and forgiving. Unfortunately, these virtues are frequently misused. The direct results are inefficient classification and overgrinding. The indirect results are added costs through recovery losses, unnecessary recirculation, and so on,

Jan 1, 1985

By A. J. Lewis, P. J. Hutcheson, M. E. Robertson, P. A. Moir, K. M. Barfoot

With the content of gold and platinum in the vast majority of ore deposits typically averaging 6 parts per million and less, the accurate and precise measurement of these metals in samples of ore and mining process streams has proven very difficult to achieve by modem spectroscopic analytical techniques. Largely because no other technique has proven suitable, the basic fire assay process has become the accepted international standard for these metals. Fire assay, however, suffers a number of disadvan­tages in the modem, competitive, high technology, and increas­ingly environmentally aware world. It is a labour intensive technique that is difficult to automate, and requires high levels of skill to ensure accuracy and consistency of results. Potentially hazardous chemical reagents are employed, of which, lead, in particular, can be a serious source of contamination to both personnel and the environment if not effectively controlled. Other dangerous elements, such as mercury and arsenic, liberated in high energy furnace operations, are further sources of possible health and pollution hazards. n contrast, the energy dispersive K X-ray fluorescence (K­XRF) technique devised by K X Technology Ltd overcomes many of the technical constraints of conventional low energy X­ray analysis, and has the potential to revolutionise assay opera­tions in precious metal mining. The technology is simply automated, requires basic operator skills, uses no chemicals, consumes less than 20kW, and is capable of detecting gold and platinum to an accuracy of O .1 parts per million by mass. The new third generation design of AZTEC laboratory instrument, released in 1994, is the result of significant technical development. Capable of analysing over 1200 samples per day, and developed primarily for grade control sampling, its applica­tions have spread to gold ore accounting from on-line conveyor belt sampling; screening of exploration samples; measurement of gold in carbon granules for Carbon-in-Pulp process control; and for conducting rapid checks to support key managemen decisions. The economic, rapid, and non destructive analysis ofup to 80g of ore for large numbers of samples, reduces sampling and sub-sampling errors, and provides improved grade estimates for ore bodies. When interfaced to a LIMS, laboratory automation and cost-savings can be further enhanced. The AZTEC design is also being modified for the analysis of platinum. The GOLDSTREAM on-line analysis system is an important new application of K-XRF to the continuous monitoring of process streams in gold ( or platinum) plants and mills. Integrat­ing the technologies of K-XRF to measure total gold, and dissolved gold spectroscopy to measure gold in solution, the insoluble fraction of gold can be deduced, and the effectiveness of the extraction process determined. Slurries are sampled automatically from selected points of the plant and pumped to the system for analysis. The information produced forms the basis for plant control and optimisation.

Jan 1, 1995

By R. Pakalnis

This paper compiles the research work conducted by the Spokane Research Laboratories in the investigation of shotcrete within underground mines to the applied design of ground support for the operator. It looks at the design methodology in terms of employing shotcrete as a fabric to confine the rock mass between the individual bolts as dictated by empirical charts. The failure mechanism in terms of its implication on design is presented with respect to the design of 6m wide tunnels for temporary and permanent openings within weak rock masses. This is reflected by field observations that relate laboratory tests to the onset of failure for the operator in order to provide guidelines for design and monitoring. This is coupled with guidelines for safe entry in terms of cure times as well as the understanding of the behaviour of the shotcrete in terms of fibres and the overall strengths that result with respect to the design of the mine openings. This enables the operator to better understand his workplace thereby provide a safer work environment.

Jan 1, 2010

By Thomas D. Henderson, Wayne R. Hopkins, Arthur Lynch

Brought on stream in 1975, the 10,000-tpd copper oxide processing plant of Anamax Mining Co. at Twin Buttes, Ariz., is now at design capacity. Based on acid agitation leaching, solvent ion exchange, and electrowinning, the Anamax plant bridges an ore to metal gap by producing mine site copper cathodes from lime-bearing oxidized feed. Until recently, such material was considered submarginal because copper recovery was uneconomic using conventional methods. The new Twin Buttes oxide plant, the largest of its kind in North America, is one stage in the expansion of Anamax, a joint venture owned equally by The Anaconda Co. and Amax Inc. Other phases include an accelerated stripping program in the pit, an expansion of the sulfide concentrator from 32,000 to 40,000 tpd, and construction of a 57 MW diesel generating station for the oxide plant. Once the basic oxide flowsheet had been selected, Anamax awarded a contract to a joint venture of Arthur G. McKee and Co.' (Western Knapp Engineering Div.) and Davy Powergas' (a member of the Davy International group). The contract covered process design, engi¬neering, procurement, and construction. The property, identified by Banner Mining Co. in the 1950s and developed by Anaconda, was put into production in 1965 as an open pit mine equipped with a 32,000-tpd sulfide flotation concentrator. The Twin Buttes mine has since become one of the largest earth¬moving operations in the world, excavating some 10 tons of waste per ton of ore. At the original sulfide mill feed rate, the mining fleet moved 375,000 tpd of material (225,000 tpd alluvium and 150,000 tpd of rock). The most significant copper mineral in the ore body is chalcopyrite, which is scattered in pockets of weak mineralization. Cap oxidation has progressed to depths of several hundred feet, principally as chryso¬colla. Present estimates place minable reserves at 347 million tons of sulfide ore grading 0.6% copper and 55 million tons of oxide ore grading 0.9% recoverable copper from 1.25% total copper. The nonre¬coverable fraction is composed of native copper and insoluble copper oxides and sulfides. The oxide ore has been partially stripped, and 25 million tons having a copper content greater than 0.6% have been stockpiled. The stripping of oxide ore to expose sulfides will continue for several years. The copper oxide studies launched by Banner Mining in the 1950s were continued by Anaconda. Process routes investigated included: acid leaching; cyanide leaching; segregation roasting; chlorination, oxidation, and reduction; flotation in combination with leaching; cal¬cite flotation plus leaching; copper oxide flotation; and sulfidization flotation. By late 1968 test work favored a low temperature roast followed by an ammonia-ammonium carbonate leach of the ore. During this period, acid leaching had been discounted because of excessive con¬sumption of expensive acid by the high limestone ore matrix. Restric¬tive SO2 emission controls in 1971 suggested an increase in acid production and availability at a lower cost. Research then switched to acid leaching, resulting in development of the present flowsheet. Mechanically agitated leaching in a cascaded series of tanks was selected in preference to vat leaching after piloting a stirred-tank system. Preliminary testing of vat leaching indicated that inter-vat solution clarification problems could be caused by gas evolution from leaching of high limestone ore. Lack of research time for resolution of this problem, plus success of the pilot agitation system, dictated the final flowsheet selection. In 1973 Anamax decided to proceed with agitation acid leaching to produce liquor for a solvent ion exchange (SIX) and electrowinning (EW) installation. At that time, such systems were proving their eco¬nomic viability, and they allowed direct recovery of high quality cath odes while bypassing the smelting and refining of lower grade cement copper precipitates. The Anamax oxide plant processes a grade of about 1% recovera¬ble copper from stockpiled sources and new mine production. Unit operations include size reduction, agitation leaching, countercurrent decantation washing of residue, pH adjustment of solution, clarifica¬tion, solvent ion exchange, and electrowinning of copper, with a mini¬mum of environmental impact. The feed to the primary crushers is composed of: 1) -10-in. stockpiled oxide ore, which has passed through the mine crusher and has been grade-segregated to allow blending for a consistent feed material. 2) -4-ft ROM oxide ore stockpiled in the early mining operation. 3) -10-in. ore currently being mined. Ore is delivered in 100-ton mine trucks to a dump pocket, where an apron feeder transfers the ore to an inclined 6-in. fixed grizzly. The grizzly oversize passes through a 48 x 60-in. primary jaw crusher, where it is reduced to -6 in. The fixed grizzly undersize and the crusher product are conveyed to a 4-in. vibrating grizzly. Oversize from this grizzly reports to a 7-ft Standard cone crusher, where it is reduced to -1 in. The crusher product and the vibrating grizzly undersize are conveyed to two 8 x 20-ft double-deck vibrating screens that operate in closed circuit with two 7-ft short head cone crushers. Screen undersize (-1/2 in.) is delivered to a covered conical fine ore stockpile with a designed live capacity of 15,000 st. Beneath the stockpile are ten Pioche belt feeders feeding two conveyor belts that supply the milling circuits. Each group of five feeders has two variable speed and three fixed speed drives. Grinding to 95% -48 mesh is done in two parallel lines, each consisting of an 111/1 x 18S -ft rod mill and a 12' x 30-ft ball mill in open circuit. Water is added to maintain a pulp density of 72% solids in the mills. Further water additions are made to the ball mill discharge sumps to create a 60% solids slurry for transfer to the leaching reactors. The nominal grinding rate is 440 tph solids. A splitter box on the product from the mills separates the incoming slurry into two streams, one for the leaching reactors and the other for the pH adjustment reactors. This split is determined by the lime content of the feed material and the pH of solution entering the pH adjustment reactors. Five 30-ft diam by 31-ft high mechanically agitated, rubber-lined leach tanks are arranged in cascade, with gravity transfer from one to another by enclosed launders. Concentrated sulfuric acid (93.2%) from storage is added to the pulp principally at the first leach tank, and the reacted slurry leaving the cascade after a 5-hr residence time at 50% solids is pumped to countercurrent decantation (CCD) wash thickeners.' At this point, most of the soluble copper has been leached from the ore. Up to 250 lb of sulfuric acid is consumed per ton of ore, the acid being supplied in tank cars from a nearby smelter. Leached slurry at 50% solids is washed countercurrently with return raffinate from the SIX plant in a series of four Doff-Oliver center caisson, 400-ft diam thickeners. Solids advance from thickeners No. I through No. 4 to the tailings dam. SIX raffinate advances from thickener No. 4 to thickener No. l, where a pregnant solution overflows to pH adjustment. To optimize solvent extraction, the pH of the pregnant solution from CCD thickener No. I is adjusted from 1.5 to 2.5 by adding unreacted ground slurry (split from the grinding circuit) to the preg¬nant overflow of No. I CCD thickener. The resulting slurry is retained for 45 min in three mechanically agitated leach tanks. CO, generated during leach and pH adjustment is ducted to a demister, where entrained acid droplets are removed. The cleaned CO, and the No. 4 CCD underflow are the only effluents from the plant. The underflow of No. 4 thickener mixes with tailings from the sulfide concentrator and is neutralized. Slurry exits the pH adjustment vessels at about 10% solids and

Jan 1, 1985

By K. E. Yassin, A. Yehia, M. Amar

Phosphate ores are the source of many commodities, such as phosphorus element, P2O5 and fertilizers. Discarding a large percentage of fine phosphate particles produced as slimes during phosphate ore processing represents a severe environmental problem, besides making the beneficiation process uneconomical. The phosphate industry is interested in a process that is efficient, with high grade and high recovery; ensures economical feasibility, with low operating cost; and is environmentally sound, with low toxicity. Numerous investigations have been conducted to try to find better processing techniques and reagents. However, reagent requirements and recovery limitations may be so high that the end does not justify the means. Reagents of biological origin are of special interest because they offer specific interactions with minerals, reduced operating costs, environmental acceptability and flexibility in adaptation. Recently, there has been a growing interest in using microorganisms as flocculants for mineral fines and as flotation collectors. 

By Guy G. Jr. Granger

INTRODUCTION Due to the current depressed state of the mining industry, many mining companies have been forced to operate at less than maximum capacity. This paper will describe how the AMAX Henderson Molybdenum Mine and Mill near Empire and Parshall, Colorado respectively have utilized operations scheduling and budgeting to achieve production targets at minimum operating costs The AMAX Henderson Molybdenum Mine and Mill have been operating most recently at approximately sixty percent of maximum capacity. OPERATIONS SCHEDULING Production Targets. The production targets are tons, operating days, tons per opera- ting day, head grade, recovery, and pounds of molybdenum. One specific objective of operations scheduling is to meet the production target for pounds of molybdenum. Present market conditions dictate that production be adjusted to match sales of molybdenum. Over-production and creation of molybdenum inventories is unacceptable. In summary, the product ion target for pounds of molybdenum must be met, but not exceeded. Capacity. The AMAX Henderson Mill single stage open crushing circuit capacity is 48,000 dry short tons per day. The AMAX Henderson Mill single stage semi-autogenous primary grinding mill circuit capacity is 38,000 dry short tons per day. All other AMAX Henderson Mi 11 circuits such as rougher flotation, regrind, cleaner flotation, lead leach, filtering, drying and concentrate handling are sized to accommodate the 38,000 dry short tons per day and pro- ducts from same. The tailing delivery system is designed to accommodate tailing from a 38,000 dry short tons per day operation. Constraints. One mill production scheduling constraint is that the mill operating schedule must be the same as mine production, ore haulage and crushing. There is a total crushed ore stockpi1e storage capacity of 240,000 dry short tons. This breaks down to 60,000 dry short tons of crushed ore over the three reclaim pan feeders for each of the four primary grinding mill circuits. However, there is only approximately 10,000 dry short tons of live crushed ore available over the three reclaim pan feeders for each of the four primary grinding mill circuits. Dozers must be utilized to re- claim and push the other crushed ore. Primary grinding mill throughput is

Jan 1, 1986

By D. K. Grubbs

Red bauxites from Breadnut Valley, Clarendon Parish, Jamaica, are very homogeneous in texture. Bauxite minerals are uniformly distributed in a groundmass, the predominant grain size being smaller than l um (Figure 1 Although the deposits have a massive, non-stratified structure, they all seem to have been affected by postformational faulting which is evidenced by shear zones running subvertically through the deposits. These shear zones stand out very clearly because of a yellow staining along their faces. Often yellow zones, ranging from a few m to several cm in thickness, have developed. When the shear zones are cut at an angle, they appear as yellow veins. Near the surface of the deposits, yellow material forms shallow irregular lenses (Figure 2). In most cases, tree roots (hair roots), or their imprints, are associated with the shear zones or stained areas. In fact, the yellowish color is especially pronounced along these roots and often disappears where the roots end (Figure 3). The mineral composition and texture of red groundmass and yellow zones are markedly different. Secondary phosphate minerals and a higher goethite to hematite ratio characterize the mineral composition of the yellow zones. It should also be noted that Al-substitution in goethite from these areas is significantly higher than in goethite occurring in the groundmass (Figure 4).

Jan 1, 1980

By A. E. Desrosiers, R. L. Kathren, D. L. Haggard, J. M. Selby

INTRODUCTION The radiological health significance of thorium-230 stems from its tendency to separate from the uranium238 parent, concentrate in bone tissues, and to subsequently irradiate the radiosensitive tissues lining the bone surfaces and the bone marrow. Indeed, thorium-230 may be the radionuclide which contributes the major dose following intake of natural uranium (Hartley and Pasternack 1979). This is reflected by the most recent recommendations of the International Commission on Radiological Protection, which specify the limits shown in Table I for the annual intake of radionuclides by occupationally exposed workers (ICRP 1979). TABLE 1. Occupational Annual Intake Limits (microcuries per year) for Selected Uranium Nuclides and Daughters (ICRP 79) [Radionuclide Ingestion Inhalation] [Uranium-238 200 0.05 Uranium-235 200 0.05 Uranium-234 200 0.03 Thorium-234 300 200 Thorium-230 3 0.02 Radium-226 2 0.5] Clearly, the relatively low annual limit of intake for thorium-230 shows it to be of greater radiological concern than its parent radionuclides. Because of the greater toxicity and different metabolism of thorium-230, monitoring only for uranium-238 does not satisfactorily identify the possible hazard from thorium-230 nor does it provide any real indication of the metabolism or biodynamics of these two radionuclides. Thorium-230 has a half-life of 80,000 years and can be detected by direct counting of the alpha particles or photons emitted during its transformation to radium-226. The 4.69 and 4.62 MeV alpha particles are distinctive and specific indicators of thorium-230 and are emitted with abundances of 76% and 24%, respectively. The principal photon, a 68 keV gamma ray, is emitted in only 0.37% of the transformations and is, therefore, not useful for low level measurements. The other photons emitted have even lower yields, or, in the case of radium L x-rays, are non-specific and, hence, useless for quantification. High sensitivity measurements of thorium-230 currently are usually accomplished by wet washing of the sample substrate, quantitative chemical separation of thorium atoms, and, finally, direct measurement of the alpha particles emitted from a massless deposition. This procedure is complicated, expensive, and time-consuming, and subject to interferences from uranium, other actinides, and other thorium isotopes. Recently, the feasibility of low-level measurement of thorium-230 by neutron activation analysis (NAA) was demonstrated (Kathren, Desrosiers and Church 1980). Two principal variations of the NAA method were used in this study: 1) instrumental NAA technique and 2) post-irradiation radiochemical separations (RCS). Instrumental NAA procedure is a nondestrucive technique which is preferred because of its simplicity. The procedure is as follows: after irradiation with a known neutron fluence, the samples are transferred to a clean container and quantitative gamma spectroscopy performed. With the radiochemical separations procedure, the sample is initially treated as in the instrumental technique. However, after irradiation, a known amount of "carrier" is added to the sample. The element(s) of interest are then separated from the rest of the matrix by distillation, precipitation and extraction techniques. The resulting sample, now free of interferring elements, is then ready for gamma-ray analysis. The use of a "carrier" is to determine the loss of element-of-interest during the chemical separations process. The neutron activation cross section of thorium-230 has an epicadmium resonance value of 1,010 barns (Mughahghab and Garber 1976) and a thermal neutron cross section of 23 barns. The 25.52 hr thorium-231 produced releases two photons of significance: an 84 keV complex, (6.5% yield) and 25.6 keV (15% yield) (Lederer and Shirley 1978). The 84 keV complex is particularly useful for quantification since neither natural uranium, thorium, their daughters, or activation products emit photons in this region. However, the higher yield of the 25.6 keV photon may result in increased sensitivity if there are no other photons of similar energy emitted by other radionuclides in the sample. PRELIMINARY STUDIES Thorium-230 standard stock solution was prepared from a pure sample of the oxide purchased from Oak Ridge National Laboratory. From this stock solution a series of samples were prepared for irradiation in the TRIGA Mark I reactor at Reed College. Various dilutions were prepared as well as thorium-230 spiked urine samples. Irradiation times varied from 1 to 54 minutes in a neutron fluence rate of 1.84 x 1012 n/ cu m-sec. The neutron spectrum was abundant in thermal neutrons, having a Cd ratio of approximately 10. Treated urine samples were also analyzed by the NAA instrumental method. Analysis of untreated urine samples was not possible due to the high background

Jan 1, 1981

By A. Gupta, S. C. Srivastava, K. K. Saroj

Bacterial degasification of methane and conventional methane drainage for generation of power have become accepted practice. Comparative economies of both the techniques have been described. Authors have discussed an alternative technique, involving complete methane biocycle. The first stage of the entire process involves gasification of coal using a consortia of bacteria to generate methane. The generated methane has been proposed to be pumped,as in conventional methane drainage. Technique described is basically similar to underground coal gasification, with the difference that in place of coal combustion, degradation of coal to lower molecular weight compounds by one set of bacteria and then methanogenesis by methanogens, producing methane have been described. Brief account of communities of bacteria that may be employed have been dealt with. Three arguments in favour of proposed technology as an alternative to conventional coal mining are: 1.Total elimination of hazardous operation. 2.Availability of power plants based on methane drainage, assuring comparative economies. 3.Possibility of utilisation of fuel cell technology for power generation giving higher efficiency. All the three phases of complete blocycle viz (1) methane generation from coal (ii) conversion of methane to hydrogen and oxygen (iii) conversion of products so obtained to methane, thereby completing the cycle have been discussed. INTRODUCTION Drainage of methane by conventional pumping process (Boxho,et.al.,1980) not only is helpful in maintaining safe extraction of coal, but with utilisation of extracted gas for power generation, also helps in over all economy of coal mining. This is gradually becoming standard practice for mining of coal in highly gassy mines. An alternative technique (Thakur et. al., 1991) of bacterial degasification of coal seams is also gradually gaining ground. The bye products of this process that is carbondioxide and water, do not contribute towards economy of coal extraction process. However the technique has its own advantage particularly in goaf area for avoiding fire hazard and drainage of methane from coal seams prior to initiation of mining operation. Either of these techniques could be applied in specific situations with success.

Jan 1, 1993

By C. Cassios

The paper covers the principles of Silver & Baryte Ores Mining Company (S&B) integrated Environmental Impact Assessment study for the whole of the extractive activity at the Fokida prefecture, over a time horizon of a quarter of a century. More specifically the paper includes: - The investigation and the evaluation of the environmental and socioeconomic variables of the specific area of concern. - The identification of the present and future impacts of the extractive activity. - An evaluation of the results of related reclamation activities. - Activity planning following a holistic approach, based on the principles of Sustainable Development, including environmental, social and economic aspects. - The monitoring of the procedure?s implementation.

Jan 1, 2003

By N. Iverson, E. Haft, V. T. McLemore, M. Woodard, E. Owen

Present and emerging technologies are renewing interest in domestic rare earth elements (REE) production. REE deposits throughout the North American Cordilleran alkaline-igneous belt are being re-examined for their economic potential. In New Mexico, the mineral deposits found in this belt are associated with Eocene–Oligocene alkaline to calc-alkaline igneous rocks. Four areas in New Mexico have been examined for their REE potential. The chondrite-normalized REE patterns are similar for all four districts, even though different REE minerals are found. Crandallite, xenotime, bastnäsite and brookite are found in fluorite veins and carbonatites at Laughlin Peak. Bastnäsite was extracted during fluorite processing from 1954-1980 from the Gallinas Mountains, where samples as high as 8% total REE are found in fluorite veins. Other REE minerals include agardite, parasite, xenotime, and monazite. Allanite, thorite and as much as 8133 ppm total REE are found in fluorite veins in the Capitan Mountains. In the Cornudas Mountains, exploration along the outer edge of the Wind Mountain nepheline syenite laccolith and within phonolite dikes, plugs, skarns and carbonate-replacement deposits in Chess Draw contain as much as 3110 ppm TREE, hosted in eudialyte, monazite, bastnäsite, and calciocatapleiite.

Feb 1, 2023

By John D. Smith

This paper describes how a knowledge of inherent rock characteristics can aid the mining engineer in his design of a mining method for a massive domelike structure. The paper shows how the pertinent rock characteristics were measured and analyzed and how the data obtained was used for design purposes. This analysis was conducted in 1964 in a producing salt dome, since that time, mine management has tried certain of the recommendations for mine design changes. The results of such changes are presented.

Jan 1, 1968