Search Documents

By Charlie Sons

Pit and underground mine operators typically use a lot of big equipment tires. Just as typically, they spend a lot of money they shouldn't on these tires. That's because tire use and maintenance are not given enough attention. That often occurs because mine management and personnel do not know the basic facts of tire use and care. If a piece of large equipment is damaged or ruined, a good explanation better he forthcoming. A ruined tire is often just a shoulder shrug. But that sort of fatalistic acceptance can cost tens or hundreds of thousands of dollars a year extra for big equipment tires. That does not have to be. There are some basic tire considerations that, if followed, will extend tire life and lower tire costs. Most companies have the inevitable conflict between the production department, which resists any restrictions that may reduce productivity, and the maintenance department. Production success is based on meeting a schedule of yards moved, while maintenance success is based on availability and equipment cost. When production falls behind schedule and equipment speeds are increased, maintenance may soon find its tire costs rapidly increasing, unless everyone understands the tires' vulnerability to damage. Unless the production department understands the problem, or restraint is applied by top management, costs may become exorbitant. At one job site, tire costs alone exceeded $250,000, to move 55 dam3 (72 000 yd3) of dirt on an 11-km cycle. The operation temporarily caught up with its schedule, but tire costs and attendant downtime soon made this a not-for-profit exercise. Because an operator must always attempt to move payload at the lowest cost, there are cases when higher than normal tire costs must be accepted. For example, in pioneering work with tandem engine scrapers, steep grades shorten tire life to less than normal. But the steep grades make shorter haul cycles possible, yielding more trips per hour than alternative earth-moving methods.

Jan 1, 1982

By R. W. Lawrence, P. B. Marchant

Biohydrometallurgy is now forty years old. Since the discovery of the role of microorganisms in the oxidation of sulphide minerals that gives rise to acid mine drainage, many workers in industry, research organizations and academia in many countries have been active in attempts to develop practical commercial processes which exploit microbiological reactions in mineral processing and extractive metallurgy. Reactions which have potential and are being actively researched include:

Jan 1, 1998

Underground mining alters ground condition, producing a disturbance in the ground water regime. The level of disturbance is dependent on the local hydrology, geology, and type of mining. Serious damage is sometimes caused by ground water- when mine roofs collapse, causing subsidence. Subsidence is either unplanned, where pillars are inadequate to provide support; or planned, where total extraction occurs over a large area. The primary objective of this study is to investigate the effects of mine subsidence on the ground water hydrology in the Warrior Coal Basin. Underground openings resulting from coal mining activities have been the most significant cause of subsidence problems in the Warrior Coal Basin, the main source of coal in Alabama. This problem will be even more serious in the future because 19 of Alabama's 24 billion tons of coal reserves are classified as an underground source (Tolson, 1982).

Jan 1, 1987

By R. Dorey

The Kennecott Ridgeway Mine in South Carolina is scheduled to complete mining and ore processing in the last quarter of 1999. Tailings are disposed in a 300 acre, lined tailings impoundment. To facilitate closure and reclamation, modification of the tailings impoundment operation has been adopted. Mining involved the sequenced development of two open pits. In 1996 mining of the South Pit was completed and backfilling of the pit with waste rock from the North Pit was initiated and will continue until mining ceases. Both pits will be reclaimed as fresh water lakes. This paper presents the physical, geochemical and hydrogeochemical evaluation of the operational and post operational management of the project. Comparison of the operational monitoring data against predicted performance is reviewed.

Jan 1, 1999

By G. Blackwell, E. Bozorgebrahimi

The trend in open pit mining has been to maintain cost competitiveness through economies of scale, particularly by implementing larger trucks and shovels. This paper considers the potential adverse impact of such scale adjustment, however, on dilution, maintenance, flexibility, and other aspects of operations. It examines the mine production characteristics affected by increased equipment size and attempts to quantify the impact on the overall operation. Reference is made to data from operations that have experienced a variety of equipment size ranges changes over the last decade.

Jan 1, 2003

By Gary Repetto

Hiring trends in the construction materials industry have remained steady through the years, with some seasonal and geographical variances. However, after several years of a depressed market, the base metals industry has begun to actively hire only over the past two years, due to the continued strength in the prices of copper, lead, zinc, molybenum, etc. The expanding precious metals industry, which for the most part escaped the depressed markets of the mid-1980s, actually preceded the base metal companies in hiring of engineers and operations personnel. The coal industry has not seemed to rebound much from the cutbacks of the early 1980s. And the uranium industry, which began its decline a year or two earlier than the other mineral industries, has remained nearly nonexistent in the United States. In nearly all of the mineral industries, new hires have been mostly in the engineering and operations areas, not exploration.

Jan 1, 1990

By M. Dosemeci, M. McCawley, J. McLaughlin, Z. Wu, F. Hearl, W. Blot, K. Peng

Proposals have been made by two organizations, the International Standards Organization (150) and the American Conference of Governmental Industrial Hygienists (ACGIH) for a revised respirable dust criteria and criteria for thoracic and inspirable dust. These criteria yield different results than criteria based on lung deposition patterns in assessing the hazards due to dust exposure. Since these differences are a function of the size distribution of the dust an analysis of dust size distributions from various mining operations was performed to determine the amount of difference that could occur. The dust size distributions available for this analysis were taken from U.S. coal mines and from Chinese metal mines. The mass of mechanically generated dust that will deposit in the alveoli was found to be in direct proportion to the ISO/ACGIH criteria estimates in the mines studied. Therefore, respirable dust estimates for substances such as coal and silica are not a problem. Estimates of exposure to diesel exhaust in these mines, however, were not always in the same proportion to the estimated alveolar deposition. Also, concern with an excess of bronchitis among miners may not be adequately addressed by the use of samplers conforming to the ISO and ACGIH criteria. The cascade impactors used to acquire the data for this analysis require four to eight substrates per sampler. For daily dust exposure assessment this method is cumbersome and time consuming. Therefore, two new samplers have been designed to meet the need for determination of deposited dust mass. These samplers follow the lung deposition curve rather than the penetration curves proposed by the ACGIH and ISO and require analysis of only two substrates per sample.

Jan 1, 1992

"With a longstanding reputation for engineering expertise, Weir Minerals continually develops solutions and technology to better serve the mining industry. Recognizing that throatbush wear rate has a major impact on the overall efficiency of slurry pumps, Weir Minerals has developed superior rotating and axial adjustment technology.In many applications, the pump’s throatbush is the component that has the shortest life compared to the impeller and liners, with considerable variability.Adjusting the gap between the throatbush and the impeller front shroud reduces hydraulic recirculation in the pump. This prevents localized wear on the throatbush, improves hydraulic efficiency and lowers the total ownership cost for the operator. To avoid impacting the plant’s production, these adjustments are often performed while the pump is operating. However, this can have safety implications for individuals working at the front of the pump unit.“Manually adjusting an alloy throatbush on a large pump requires several people and is laborintensive. It requires mechanical tools to adjust the four pusher bolts, one at a time, in order to reduce the gap between the throatbush and impeller. We wanted to find a safer and quicker way to extend the wear life of the pump with regular adjustments, which led us to development of this technology,” said Marcus Lane, global product manager for centrifugal pumps for Weir Minerals.“Our automated throatbush adjustment solutions are available for pumps fitted with either rubber or alloy throatbushes on Warman slurry pumps used in the most arduous applications, and have been designed with our customers’ safety and pump operation in mind. By mechanizing the adjustment procedure, personnel are removed from the line of fire, and the accuracy of axial movement is increased,” said Ron Bourgeois, director of slurry pumping technology group for Weir Minerals."

Mar 1, 2019

The deformation, failure, and filling characteristics of a caving roof in the initial and normal mining stages of a pitching oblique longwall mining area are analyzed using large-scale threedimensional physical-similitude experiments and numerical calculations to study the characteristics of roof fracture and migration in a steeply dipping seam. The results show that the roof fracture development has evident sequential and spatial characteristics. Among them, immediate roof breaking in different parts of the mining area shows difference in time and space. The failure sequence of the immediate roof in different areas changes with the mining; unique regional stability evolution characteristics are observed in the suspended immediate roof simultaneously, resulting in its significant regional stability on the goaf filling.

Jan 7, 2020

By Huayang Luo, Hui Li, Wei Zhou, Gang Chen, Scott Huang

The beach and offshore gold resources demonstrated at Nome, Alaska are some of the richest found in Alaska. They contain potentially significant resources that may be exploited in the future. Several companies have contributed to the exploration and reserve estimation in Nome offshore gold deposits. More than 3,000 holes were drilled and over 10,000 offshore samples were analyzed in the Nome offshore areas of approximately 40 km2. Those 3,000 plus drill hole logs were converted into digital formats comparable with ArcGIS software. Considerable amounts of mineral resources data were processed and visualized using ArcGIS 8.3 and its geostatistic, 3D analysis, and spatial analysis components. In this study, based on the data processing and visualization results of ArcGIS, a user-friendly website for mineral resource management and utilization is developed using ArcIMS 4.0.1. ArcIMS is a GIS solution to build and deliver maps, data, and tools over the Internet. The Nome offshore mineral resources website presents the geostatistic and GIS analysis information. This site allows clients to access the information and perform ArcGIS analysis, such as interactive data query, and map layers display of the gold resource distribution, average grade, gold reserve, and relative mineral resource estimation via remote computers. With linkage to other related mining web sites, this web site allows users to search for related publications and more flexibly manage the information. A few other appropriate customized tools are also being developed to assist interactions between the server and clients for data analysis and management.

Jan 1, 2005

The floatability of a bituminous coal in NaG solutions was evaluated using a modified Hallimond tube to delineate the role of the electrostatic interaction between bubbles and particles in determining the coal hydrophobicity. Zeta potential measurements showed that bubbles are negatively charged in the entire pH range tested, while coal particles are positively charged below pH 6.0 and negatively charged above it. Also, both sodium and chloride ions were confirmed to act as indifferent ions without any specific effects for both coal particles and bubbles. Flotation as a function of pH exhibited a maximum and minimum at low salt concentrations which is shown to be determined mainly by the coal hydrophobicity as measured by a new hydrophobic levitation technique. At high salt concentrations (above 0.1 mole/dm3), the flotation without such maximum or minimum is controlled by the electrostatic interaction between the bubble and the particle.

Jan 1, 1992

By David M. Parkes

The hydraulic movement of coal is here defined as the movement of all sizes of coal in pipes and open flumes, by gravity and against gravity. It is not restricted to coal which is in slurry form. In other words, it is not crushed to a size in the 8 to 20 mesh size range. The top size could be as high as 12 inches. The dewatering of coal which is transported hydraulically is carried out to restore the coal to a suitable form for further cleaning, or for transportation by other methods. The process involves complete separation of all the coal, wood and rock from the water so that the water can be recycled without undue damage to pumps, pipes and monitors.

Jan 1, 1976

By Stephen D. Hill, C. R. Ferguson, T. H. Jeffers, P. G. Bennett

The U.S. Bureau of Mines' Salt Lake City Research Center has developed porous polymeric beads containing immobilized non-living biological materials for extracting metal contaminants from waste waters. Immobilized biological materials include peat moss, algae, biological polymers, and other materials that demonstrate high affinities for heavy metals. The beads, designated as BIO-FIX beads, have distinct advantages over traditional methods of utilizing biological materials in that they have excellent handling characteristics and can be used in conventional processing equipment or low-maintenance systems. Toxic metals such as copper, cadmium, zinc, lead, and mercury are several of the many heavy metals effectively removed from mine waste waters using BIO-FIX beads, Continuous cyclic testing indicated that the beads continued to produce treated effluents which met National Drinking Water Standards (NOWS) after 150 loading-elution cycles. Adsorbed metals were removed from the beads using dilute mineral acids. In many cases, the extracted metals were further concentrated to enable processors to reclaim the metals, thus minimizing the generation of a hazardous sludge, Tests indicated that use of the beads in a low­maintenance system was particularly effective for treating remote acid mine drainage waters and small toxic seeps from hard-rock mining districts.

Jan 1, 1991

By Paul F. Ziemkiewicz, Aaron Noble, Christopher R. Vass

The rare earth element (REE) industry has sought to develop ore deposits where geologic processes have produced mineralized zones with commercially attractive concentrations. These deposits are extremely uncommon, particularly in the United States. Given the criticality of these materials and the need for a sustainable domestic supply, the current research seeks to leverage the generation and treatment of acid mine drainage (AMD) as an autogenous process that can lead to concentrated REE resources. 

By John R. Buzek

Thickeners are simply large tanks, usually circular in shape, which are designed to allow settling of solids and to operate with continuous overflow of clear water and underflow of thick pulp. The dimensions of the thickener are usually such that dewatering of very fine pulps may be accomplished while still 1 overflowing clear water. Some thickeners such as the Genter, Hardinge and Hydrotator types combine thickening with filtering2 while others such as the Dorr type are pure thickenersl,2,3. A schematic diagram of the traction type Dorr thickener is shown in Figure 1. This type is appropriate for tanks over 15 m (50 ft) in diameter. This tank employs a rotating raking mechanism which moves the settled material toward the central discharge. For this and other thickeners, it is common to have a shallow conical tank bottom in order to conform to the geometry of the raking mechanism, and it is often desirable to elevate the tank for ease of access to the product. When the tank does not rest on the ground, the forces resisted by the cone are large, and thick plates must be employed. The fabrication of these tanks requires temporary supports in order to erect the cone. A flat-bottomed tank could also be used because the settled material would soon form a hardened conical surface. However, because of the presence of large bending forces, even larger plate thicknesses are required than for the conical bottom. Significant cost savings often can be realized by the use of a scalloped-bottomed tank such as the one partially shown in Figure 2. The particular scalloped bottom discussed in this paper (and shown in the Figure) employs radial beams forming the outline of the cone-shaped bottom. These beams are supported directly by columns. Cone segments are hung between adjacent beams. The exact geometry of these segments depends upon the cone angle and radius, the number of radial beams, and their inclination. The geometry is chosen to satisfy certain clearance restraints and to utilize the material as efficiently as possible. The resulting thickness of these segments is significantly less than that of the

Jan 1, 1977

By Ruari Soutar-Dawson, Fisher Wang, Alan Boylston, Michael Denzel

Vertical stirred mills are increasingly used for fine grinding applications in the mineral processing industry due to their high energy efficiency. Thus, modeling power draw is of great interest proven by the effort in previous work including analytical models. In this contribution the development of a DEM-CFD coupled model is presented to determine power draw under different operating conditions. These include grinding media filling level, shaft speed and fluidization as well as changes in grinding compartment configuration. An extensive test program on an especially equipped test mill is initiated to validate the model.

Feb 22, 2026

By F. Heivilin

Little did I know, in 1977, that when the A. P. Green Refractories Raw Material Manager showed me 5-6 burlap bags with samples of calcined high alumina bauxite in their testing lab that this was the start of China moving to be the number one user and producer of calcined refractory bauxite. According to Ted Dickson in his August 2008 Industrial Minerals article China produced about 4 million tons of calcined bauxite in 2007 using 2 million tons themselves. They imposed an export limitation of 970,000 tons in 2007 and 940,000 tons in 2008. A 10% growth will take up the difference between exports and production in 4 years. Two of these years are gone. It will take only 4 more years to eliminate the export quota in home use. Then they will be importing unless they increase production. Guyana was exporting over a half million tons in 1975 and sold less than 70,000 tons in 2002. Basai Metals Group bought Guyana?s deposits and is rose to 250,000 tons in 2007 and expects to produce 280,000 tons in 2008. PRICES According to the USGS Prices dropped from $172/per ton for Guyana calcines in 1980 just after the start of Chinese production to $122 in 1985. Guyana prices averaged around $120/ton from 1985 to 2005. China?s price dropped as low as $45/ton in 1995 undercutting Guyana and making it virtually impossible for anyone to get into the market. The price suddenly escalated to $550/ton FOB China in the summer of 2008 when China actually cut its exports in half. The price dropped in the fall as orders dropped. This is a four to five fold price increase. Is this a shortage of bauxite or a monopoly? Australia dropped out of the market in 2008 and Surinam, controlled by Alcoa, is not participating right now. Will these two come back in to make up the difference? Will the price hold up so they can make a profit? [ ] The low prices have undoubtedly affected the prices of the 60 and 79% alumina bauxite which can hold down the quantity of 80% plus calcined refractory needed in the world market. China is starting to upgrade lower quality bauxite up to 90% alumina. With high prices kaolin alteration to high alumina comes into play. The calcined bauxite is also used for proponents, Brown fused alumina, and abrasive grades which compete with Refractories. These and the tightness of supplies needed for metallurgical will hold prices up. TONNAGE China is the number one supplier and consumer of high alumina calcined bauxite in the world. Basai Metals Group Guyana (BMGG) is owned and controlled by Basai Minerals Group of China. This appears to be the second largest supplier. Australia has dropped production and Brazil is just starting to expand. It appears China is going to replace some of exports caused by the Export License 940,000 ton maximum in 2008 by raising Guyana?s (BMGG) production of calcined refractory grade bauxite. Companies exceeded restriction in 2007. Fines have been imposed for 2008. In August 2008 they appear on line to meet the 2008 quota. After August prices have dropped off as orders dropped due to the recession. Guyana was the largest producer in 1975 with 769,000 tons which decreased to less than 79,000 tons in 2002. The U. S. is a small part of the world production. I have used the United States charts to represent world imports because I have little data on what other countries import and pay FOB for their bauxite. China started exporting calcined 80% plus refractory bauxite to the United States in 1979 with 24,000 tons. By 1985 they were the number one importer with 169,000 tons. Guyana who had been number one in shipments to the United States gradually decreased to 36,000 tons in 2006. Guyana has been purchased by China BMGG and will increase there production to over 200,000 tons in 2009. Australia shut down production in 2008 and Surinam has elected to not send any Calcined bauxite to the United States. Imports to the United States from 1978 to present are as follows: [ ] Refractories are important because they affect 96% of the GNP. During the cold war we had stockpiles of 80% refractory grade bauxite

Jan 1, 2009

By A. G. Oppegaard

Most iron ores treated by the R-N direct reduction process yield metallic iron products considerably lower in titanium, manganese, and chromium oxides and alkaline metal sulfates/sulfides than were contained in the original ores. These metallic iron products are suitable as feed stock for the open hearth and electric steel-making furnaces. The elements which are rejected in part are acceptable in the product since the product is designed to by-pass the blast furnace. R-N reduction conditions (PCO+H2-1 atmosphere, 1830° to 2150° F.) are adjusted for each ore. The iron ore which is reduced to 90 to 95 percent metallic iron is then subjected to the conventional beneficiation techniques. Under these conditions, 55 to 80 percent of titanium oxides, 75 to 95 percent of manganese oxides, 60 to 90 percent of chromium oxides and up to 97 percent of alkaline metal sulfates contained in the ore are rejected with the gangue to the non- magnetic tailings. The metallic iron products illustrated in this work contained 89 to 96 percent total iron, one to five percent TiO2, 0.2 to one percent MnO, 0.3 to 1.6 percent Cr2O3 and/or up to one percent alkaline metal sulfide. Usually only one of these components was present. Recoveries ranged from 80 to 96 percent of the iron in ore.

Jan 1, 1958

By Arthur G. Strassburger

INTRODUCTION High in the Sierra Nevada Mountains of California, some 50 airline miles (80 km) northeast of Fresno, and near the John Muir Wilderness and Kings Canyon National Park, a large underground hydroelectric project is under construction. Pacific Gas & Electric (PG&E) Company's 1,125 MW Helms Pumped Storage Project exhibits a number of impressive statistics, unusual features, and other characteristics of interest to the tunneling or power plant designer and construction contractor. The most significant underground facilities include almost 20,000 ft (6,096 m) of 27-ft (8.2 m) diam concrete-lined pressure tunnel; 3,700 ft (1,128 m) of access tunnel; 1,600 ft (488 m) of steel-lined high-pressure conduit, 2 major underground chambers more than 1,000 ft (305 m) below ground; 3 deep vertical shafts, and one steep inclined shaft. Maximum static pressures within the conduits range from 200 ft (61 m) to 1,744 ft (532 m), with hydraulic transients that increase pressure to 2,500 ft (762 m). The purpose of these underground works is to provide 475,000 hp (354,350 KW) of water power to each of the 3 reversible pump-turbines, each connected to a 375 MW generator motor. The units, rated at 1,744 ft (532 m) maximum static head, are among the world's front-runners, considering the size-head combination. The Helms Project develops the existing power drop between two of PG&E's reservoirs, Courtright Lake and Lake Wishon. These reservoirs are retained by two concrete-faced rockfill dams completed in 1958, each storing approximately 125,000 acre ft (154 x 106 m3) of water. Although the project is intended to operate on a typical

Jan 1, 1981

By Ruipeng Qian, Pengfei Wang, Guorui Feng, XianJie Du, Jun Guo, Yuxia Guo, Tingye Qi, JinWen Bai

"A numerical modeling was conducted to describe the behavior of overlying strata on the longwall top coal caving face for exploitation of a 16.8 m thick coal seam. Three typical structural models, including the Cantilever Structure (CS), Lower Cantilever and Upper Hinged Arch Structure (LC&UHA), and Lower Arch and Upper Voussoir Beam (LA&UVB), were developed. Based on mechanical analysis of the different structures of the key strata, and considering the behaviors of the broken igneous rock strata, a method was proposed and applied to estimate the structures of the overburden strata. The results had been verified by a field micro-seismic monitoring test. The paper provides a foundational method to determine the shield loadings for the top coal caving longwall face.INTRODUCTIONLongwall top coal caving (LTCC) is a highly productive underground mining technology which has been widely applied to the exploitation of the thick coal seams in China and other countries due to its high efficiency (Ju and Xu, 2013; Ju, Xu, and Wang, 2011; Liu et al., 2009). In recent years, a large amount of research on mining pressure forecast, strata control, and mechanical equipment improvement of the LTCC technology has been carried out, which greatly advances the field application of the technology (Liu et al., 2009; Yu, 2016; Dou et al., 2014; Feng et al., 2011; Chen and Li, 2011; Yin, Yan, and An, 2008). In 2006, the LTCC technology was first applied to the exploitation in a 20 m thick coal seam at the Tashan Coal Mine in China (Yan et al., 2011). Ten years of mining at the Tashan Coal Mine has highlighted the importance of the support management in controlling the roof strata on the extra-thick LTCC face. The mining pressure is closely related to the structural features of the overlying strata and its movement laws (Yu, 2016; Dou et al., 2014; Feng et al., 2011). However, the distributions of three zones—caving zone, fracture zone, and deformation zone—on the fully mechanized caving longwalls changed significantly with the increase in thickness of the coal seam (Chen and Li, 2011). The behavior changes of the roof strata led to abnormal pressure in the mining face and resulted in the difficulty of surrounding rock control (Yin, Yan, and An, 2008; Liu et al., 2009; Yan et al., 2011; Gong and Jin, 2008). Therefore, the theoretical research focused on the behavior of overlying strata to reveal the laws of mining pressure has important theoretical significance and practical value.Many classical studies (Qian and Shi, 2003; Feng, 2010; Yu, 2015; Yu, Yan, and Liu, 2012) had been done to describe the behavior of overlying strata in the mining process. It has also been reported that magma intrusion causes an important effect on the surrounding rock, coal, and methane (Wang et al., 2005; Liu et al., 2007). On the one hand, the property and structure of the coal seam was obviously changed by the magma intrusion and resulted in a potential danger of a gas outburst during the mining process (Chen et al., 2012; Wang et al., 2014). On the other hand, the hard igneous strata and the joints occurred with the magma cooled, causing an abnormal behavior of overlying strata and resulting in a series of dynamic disasters during mining (Xuan, Xu, and Lu, 2014; Lu et al., 2016). In fact, many coal fields in China are intruded by igneous sill, including the Datong, Shuozhou, Huainan, and Xuzhou coal fields (Chen et al., 2014; Wu, 2011). The 3–5 coal seam at Tashan Coal Mine in Datong coal field is very thick and is intruded by a large area of layered lamprophyre rock. Face falls and shield failures occurred frequently during the face retreat."

Jan 1, 2019