Search Documents

By J. W. Cooksley

Seismic methods provide an efficient and comprehensive approach to overburden studies pertinent to mining exploration and development, and to other mining and civil engineering problems such as rock mechanics, slope stability, and foundation engineering. For the purpose of defining geologic units and structural features, these methods are generally regarded as the most accurate, but most expensive, of the commonly-used geophysical exploration methods. Although the accuracy and cost of seismic work are generally affected adversely by rugged topography and complicated geologic conditions, it is in rough terrain and complex geology that seismic methods offer important advantages in overburden investigations. For example, to find the surface of rock underlying unconsolidated overburden at depths of approximately 200 feet, a 50-foot spacing of drill holes along the profile line would be required to yield a degree of resolution and accuracy similar to that obtained from a 50-foot spacing between seismic detectors along the same line. See Figure 1. In cases similar to that shown in Figure 1, a twelve-channel recording seismic system would be used. The main components of such a system would be: 1. detectors (commonly referred to as geophones) which convert the ground movement resulting from seismic waves into an electrical signal. 2. a multi-conductor cable which connects the seismic detectors to the amplifiers. 3. ampliiiers, amplify and filter the electrical signals . 4. oscillograph, records the amplified signal. 5. the blaster and firing line. A typical layout of the seismic spread and the components of the system Is shown in Figure 2.

Jan 1, 1968

By M. Yekeler

The critical surface tension of wetting values (Ye) of realgar (AsS), talc [Mg3si401o (OH) 2]' stibnite (Sb2S3), and sulfur (S) were determined by flotation in the absence of conventional flotation collectors as 38.7, 38.0, 35.5, and 30.0 dyne/cm, respectively. The surface tensions of flotation media were arranged by methanol. Separation of binary mixtures of these minerals was performed exploiting their Ye differences-which form the basis of the "ganuna flotation process". One step flotation test showed that sulfur floats preferentially from its mixtures with realgar and stibnite at recoveries of 73.6 and 70.7 % and grades of 81.7 and 91.2 %, respectively. The separation of stibnite from realgar gave a recovery of 4.1 % and a grade of 41.2 % for stibnite, indicate that a minimal Ye difference of 3.6±0.2 dyne/cm is essential for such separation when conventional flotation reagents are not used. This paper presents data and describes the approach employed in these separations.

Jan 1, 1994

The design/optimization of the pump and cyclones to maximize grinding circuit efficiency first requires a concise understanding of, and clearly defined specifications for, desired grinding circuit performance. Subsequently, the pump and cyclone performances that provide the desired grinding circuit performance can be defined. Once the performance requirements of each process unit are determined, selection of physical equipment parameters that will deliver those performances can be carried out. The Functional Performance Equation shows that there are two distinct efficiencies in closed circuit ball milling. One of these, ?Circuit Classification System Efficiency? (CSE), is the fraction of ?coarse? material inside the ball mill upon which grinding energy is deliberately expended, versus the remaining fraction of ?fines? or finished size material inside the mill, upon which grinding energy is wasted (on over-grinding). The role of the pump and cyclones is to maximize CSE, which is the desired grinding circuit performance. The obtainable, target CSE for any given circuit can be estimated, for example by referring to a plant data base of CSE?s. Design/optimization guidelines then allow us to specify the pump and cyclone performances that will achieve the target CSE. This paper outlines the step-by-step, systematic method of pump and cyclone selection which maximizes CSE. Numerous examples of its successful application are provided.

Jan 1, 2011

By L. R. Shotwell, C. F. Voss, R. J. Bastian

Pacific Northwest Laboratory (PNL) currently supports the U.S. Department of Energy's Office of Civilian Radioactive Waste Management in developing and evaluating analytical methods for assessing the suitability of sites for geologic disposal of high-level radioactive waste. The research includes consideration of hydrological, geomechanical , geochemical , and waste package components and the evaluation of the degree of coupling that can occur between two or more of these components. The PNL effort and those of other research groups investing potential waste sites in the U.S. and abroad are producing a suite of computer codes to analyze the long-term performace of the proposed repository sites. This paper summarizes the ongoing research in rock mechanics at PNL involving flow through jointed rock. The objective of this research is to develop a methodology for modeling the coupled mechanical-hydrological process of flow through joints and then attempt to validate a "simple" model using small -scale laboratory test data as a basis for judging whether the approach has merit. This paper discusses the laboratory tests being conducted to develop s joint behavioral constitutive model for the numerical method under development and the modeling approach being considered.

Jan 1, 1986

By R. A. Seitz

This paper presents a framework for analyzing the theory and industrial practice of coal flotation and gives some examples of its use for understanding flotation phenomena and optimizing/controlling flotation circuit performance. It is based on extensive laboratory and in plant test work conducted over the past several years by researchers at MTU as well as an analysis of the literature. Previous researchers have usually considered either the surface chemistry or the kinetics of coal flotation behavior, only rarely have these factors been considered together. However, these factors must be considered together in order to gain a clear understanding of the theory underlying coal flotation such that its practical application can be optimized. Fortunately, this complex objective can be achieved by considering the recovery and rate of recovery of the different types of particles present in the feed to coal flotation circuits and the fundamental mechanisms responsible for these recovery phenomena. The influence of three major groups of variables must be considered: control variables (reagent additions, aeration rate, etc.); disturbance variables (feed pH, percent solids, etc.); and circuit design variables (number of cells, circuit arrangement, etc.). Each of these groups of variables affects process kinetics in a clearly understandable manner, which, once determined, is extremely useful in circuit design and optimization. This paper includes a discussion of the use of the proposed framework to explain the effects of some coal characteristics on flotation performance. In addition, an example of using this analysis to optimize the performance of a coal flotation circuit using frother and collector addition levels is included.

Jan 1, 1985

By R. M. Rowe, A. K. Bhasin, D. Malhotra

Introduction Most primary molybdenite producers use a selective flotation process in which molybdenite is floated from the ore while other sulfide and nonsulfide gangue minerals are depressed in the same step. The process was developed at the Climax mill. Reagents used in the rougher flotation stage include vapor oil (collector), syntex (surfactant), pine oil (frother), and occasionally sodium cyanide and Nokes reagent (depressant). Rougher concentrate is upgraded by cleaner flotation to produce market-grade molybdenite concentrates. Reagents used in the cleaner flotation stage are Dowfroth 250, vapor oil, sodium cyanide, and Nokes reagent. The development of the flotation reagent scheme at Climax and the role of the reagents have been well described by Born et al. (1976) and Malhotra et al. (1976, 1977a, 1977b, 1977c, 1980). The hydrocarbon collector, vapor oil, accounts for approximately 50% of the total molybdenite flotation reagent cost. Because vapor oil sources are limited, and the cost of vapor oil has increased significantly over the last decade, several studies have been done to evaluate alternate oil-based collectors and/or blends of collectors that would produce similar metallurgical results at a reduced cost, or increase the overall molybdenite recovery at the same cost (Smit and Bhasin, 1983; Hahn, 1969; Smith and Bhappu, 1971). The approach taken in the present study was to evaluate alternate nonoil-based collectors and collector systems that are less expensive than vapor oil. A series of potential nonoil-based collector classes were identified and evaluated in the laboratory against the current collector system. The metallurgical performance of these collector classes was related to their chemical structures. The results of this study are discussed. Collector classes A survey of sulfide mineral collectors was performed with the objective of identifying and selecting potential collectors for molybdenite flotation. The available reagents were categorized into 10 general classes. Table 1 summarizes these collector classes, their chemical formulas, the manufacturers, and selected commercial collectors in each class that were evaluated in the present study. Experimental procedure A Climax ore sample, assaying 0.3% MoS2, 2.2% FeS2, 0.007% Cu, 0.003% Pb, and 0.03 oz per ton Ag, was used for this study. Standard laboratory rougher flotation test procedure involved grinding a 2-kg ore charge in a rod mill at 60% solids. Reagents were added to the rod mill including a collector, syntex (0.005 kg/t), pine oil (0.03 kg/t), lime (to adjust pH to 8), and sodium silicate (0.15 kg/t). The ground pulp was transferred to a 1000-g cell, and flotation was performed at 35% solids and 1800 rpm using a Denver D-1 flotation machine. Concentrate was collected for a flotation time of six minutes. The general approach used in the present study was to substitute the nonoil-based collectors at two to three different dosage levels (0.01 to 0.15 kg/t) for vapor oil in the bench-scale, open-circuit rougher flotation tests

Jan 1, 1987

By Verya Nasri, Mehdi Bakhshi

"Fiber reinforcement has emerged as an alternative to steel bars in precast concrete segments due to advantages such as saving cost and reducing production time while developing a more robust product with improved handling and long-term durability. ACI recently drafted a new report as the first design guideline on FRC tunnel segments to provide specific guidance for this emerging technology. ACI document offers general information on the history of FRC precast segments from tunneling projects throughout the world; a procedure for structural analysis and design based on governing load cases, and a description of the material parameters, tests and analyses required to complete the design. This paper summarizes the design considerations in this ACI guideline prepared by the authors of this paper as the main contributors. Application of this guideline to design of a tunnel with an internal diameter of 5.5 m (18 ft) results in elimination of steel bars.INTRODUCTIONPrecast concrete segments are installed to support the tunnel excavation behind the Tunnel Boring Machine (TBM) in soft ground and weak rock applications. The TBM advances by thrusting off the completed rings of precast concrete segments that provide both the initial and final ground support as part of a one-pass lining system. These segments are typically designed to resist the permanent loads from the ground and groundwater as well as the temporary loads from production, transportation and construction. Tunnel segments are generally reinforced to resist the tensile stresses at both the Serviceability (SLS) and the Ultimate Limit States (ULS). With traditional rebar, a significant amount of labor is needed to assemble the cages and place the rebar, which results in higher production costs.Fiber Reinforced Concrete (FRC) can be used to enhance the production, handling, and placement of precast concrete segments. This is because of the uniform dispersion of fibers throughout the segment to include the concrete cover, which is very advantageous for resisting the bursting and spalling stresses. These stresses develop as a result of the high loads induced on the segments during the TBM jacking process. The presence of fiber in the concrete matrix helps mitigate against unintentional impact loads during segment handling and tunnel construction operations."

Jan 1, 2016

By Harry J. Fitzgerald

During World War II mining machinery manufacturers were limited in the development of their product improvement programs. Following the war, however, the ideas and intentions of both the users and manufacturers of mining equipment became evident. The Coal Industry launched a series of events which indicated their determination to rise to the economic challenge of developing profitable machines which would eliminate the out-dated and back-breaking methods of mining previously used. Two major technological advances were developed as a result of the ambitious goals forecast by the Coal Industry: 1. Coal mining was going "off-track" and concentrated mining operations were to follow in rapid succession. 2. Carbide tools provided the remaining missing contribution to another technological breakthrough....Continuous Mining. Little did the inventors realize the significance of the misnomer they created because twenty-five years later the industry is still striving to secure the results implied by the meaning of the word...."Continuous". Nevertheless, all major manufacturers embarked on programs in an attempt to compete for recognition in this new mechanized-mining endeavor Eventually in 1950 there were three types of boring machines and two types of ripping machines being manufactured. Mining Speed was the desired goal.

Jan 1, 1970

By G. T. Lineberry, L. Adler

Due to safety-imposed constraints on clearances for mobile bulk handling equipment, it is necessary to optimally select a unit based on speed and size. The unit cannot be both large and fast. Since output is proportional to both size (or capacity) and speed, the combination must be carefully examined to maximize output. A simple graphical procedure and a calculus-based solution are presented to accomplish this. While the procedure applies to all mobile bulk handlers, as an example of the solution technique, attention is focused on shuttle cars. Background Major variables To fully define a bulk handling problem, the conditions, equipment, and activities must be characterized. The conditions and activities, when lumped together, are termed "encumbered space," since they "act to impede motion, as with a burden" (Lineberry, 1979). The insertion of mobile bulk handling equipment into what is already a difficult set of conditions and activities compounds the state of encumbrance, as limited space is competed for by many normal and life support systems. Long (1972) recognized the effects of design criteria, including road width, on haulage vehicle speed and, therefore, on production. Velocity -clearance curves Velocity-clearance curves are either available or can be constructed in the field. A preliminary set of curves for average conditions and activities is shown in Fig. 1, where clearances are only for the side of the vehicle (Lineberry and Adler, 1984). These curves set the safe speed limits for a vehicle operating at given clearances, under given conditions and activities. When feasible, velocity-clearance curves should be constructed through field measurement and observation. Curve construction should also consider haulway roughness, distances, and operator skill, as well as loading and dumping characteristics. It should be noted that haulage capacity determination is a total systems problem, not one just dependent on velocity and clearances. Production requirements and company capabilities also influence capacity determination.

Jan 10, 1985

By Koehler Stout

Stopewall or room closure can be a problem in nining operations. In some mines, wall closure causes ore passes and nanways to collapse when they are enclosed in nine fill. When this phe- nomena occurs, heavy ground and, or, rock bursts frequently happen. Often, ground problems become progressively worse as mining in the stope block progresses toward the upper level. The sill and pillars in the level above may experi ence heavy ground and bursts. Sometimes the conditions get so bad in the stope that it is unsafe to mine the ore, so the stope is abandoned and the ore is lost.

Jan 1, 1980

By E. Alan Haley

Accurate and economic control of line and grade on long tunnels, large structures, excavations and waterways, has been a problem to surveyors and engineers for decades. The conventional method of surveying, incorporating a level, transit, and a number of surveying technicians, has proven, in the past, to be a very expensive and time-consuming operation. Alignment with a laser has solved most of the problem. Figure 1. With the advent of the Perkin-Elmer Model 5620 Construction Laser, use of laser light is now both dependable and economically feasible for unlimited applications in modern construction and surveying. The laser projects a continuous, narrow red beam of brilliant light, providing a constant alignment reference, and will not interfere with operations.

Jan 1, 1968

By R. M. Balderrama

Bench-scale laboratory flotation and gravity separation tests were conducted on tailings samples to remove the sulfidic material, mainly pyrite, the source of acid generation. A combination of xanthate collectors, promoters, and frothers were used during flotation. Pyrite recoveries were in the range of 42 to 97%, depending on the tailings being treated. Sulfide sulfur contents of 12.8 to 0.37% in the feeds were reduced to 8.68 to 0.01% in the treated tails. Flotation tests were conducted to evaluate the ARD potential as a function of percent pyrite remaining in the tails. Standard ARD predictive tests were used to evaluate the success of the treatment. In some cases, removal of only 50 to 55% of the pyritic fraction was required, thereby demonstrating the conversion of the waste material from acidic to non-acidic. A laboratory vanning table was used to evaluate the amenability of sulfide-bearing tailings samples to gravity separation. The pyrite recoveries varied from 38 to 86%. The sulfide sulfur content of 12.8 to 0.37% in the feeds was reduced to 6.0 to 0.14% in the treated tails. Predictive ARD tests performed on tailings before and after the gravity removal of pyrite showed that most samples changed from "probably" acid producing to the "uncertain" range. Data reported and analyzed in this paper demonstrate source control for ARD prevention through the removal of metal sulfides from sulfide-bearing wastes using conventional flotation and gravity separation techniques.

Jan 1, 1995

By Carter Brown, Kate Brown Requist, Eric Lutz, Moe Momayez, Athira Satheesh

New mining health and safety training modalities are becoming increasingly prevalent in the underground mining industry. Various digital training tools have been developed over the past several years, but the extent of their use remains unclear. Advances in gamified training by way of computerbased video games and virtual reality (VR) have opened a new avenue for mine rescue and self-escape training, but these methods have not been widely adopted across the mining industry. Mine rescue and self-escape situations require a mix of in-classroom training as well as live drills, but it is important to assess the extent of and effectiveness of new training modalities. The Mine Rescue and Self-Escape Survey (MRSES) was distributed to underground mining operations to collect perceptions of current training effectiveness as well as willingness to adopt new training methods as a complement to live rescue drills. Responses from the MRSES indicate that adoption of digital training technologies has been slow-going despite an interest in their use. Further, there appears to be no meaningful connection between more frequent escape and rescue training and feelings of emergency preparedness. With relatively little use of already developed digital training tools but an interest in their adoption, it may be time to reassess current emergency preparedness training philosophies.

May 1, 2025

By Gregory R. Wessel

Sulfur is a nonmetallic element widely distributed in nature and of great physical and economic importance. It is the 14th most abundant element in the Earth's crust (0.06%) and an important constituent of animal and plant life. Sulfur has been known and used since ancient times for a number of medicinal and industrial uses. At present, most sulfur is used to generate sulfuric acid that is used in a wide variety of industrial processes, particularly the production of fertilizer. Because of this, sulfuric acid (and hence sulfur) consumption is often regarded as a good index of a nation's industrial development. In the past, sulfur was mined from surface occurrences in several geologic environments, and was used in relatively small amounts. With time, the uses of sulfur and sulfuric acid expanded, as has the need for larger quantities of these commodities. Sulfur is now mined from both surface and underground deposits, and is recovered as a byproduct from a number of industrial processes. Despite valiant efforts and years of work by sulfur explorationists and others, many aspects of sulfur mineralization remain controversial. Almost as controversial is the spelling of the word sulfur. The English spelling sulphur commonly is used outside America and in the American sulfur mining industry, but sulfur is the correct American spelling as approved by the American Chemical Society, the American Geological Institute, and many others. Those new to the American sulfur industry often find it puzzling to be reprimanded for using the correct American spelling. Sulfur resources are abundant and widespread, but the extent to which they can be classified as reserves is constrained by pre- vailing prices and extraction technologies. At present, sulfur can be economically mined from very few deposits. The sulfur industry is roughly divisible into two sectors: voluntary (or discretionary) and involuntary (or nondiscretionary). In voluntary production, the mining of sulfur or pyrites is the sole objective, and the recovery of the resource is as complete as economic conditions will allow. During involuntary production, sulfur or sulfuric acid (termed recovered sulfur) are produced as byproducts, and the quantity of the output is dictated by the demand for the primary product. Voluntary sulfur now accounts for only about 35% of the elemental sulfur produced worldwide, and most inves- tigators believe that voluntary sulfur will be less important in the future. Sulfur sources and products are described as follows (after Barker, 1983): Sulfur Sources: Combined sulfur-sulfur that occurs in nature combined with other elements, commonly referring to sulfides and sulfates. Cupriferous pyrites-pyrite containing minor amounts of cop- per sulfides. Hydrogen sulfide-a toxic gas that occurs in petroleum and natural gas. Involuntary sulfur-sulfur produced as a byproduct in response to legislative or process mandates. Native sulfur-naturally occurring elemental sulfur. Nonferrous metal sulfides-opper, lead, zinc, nickel, and molybdenum sulfides that are processed for their metal content. Organic sulfur complex organic sulfur compounds that occur in petroleum, coal, oil shale, and tar sands. Pyrites-iron sulfide minerals that include pyrite, marcasite, and pyrrhotite. Sulfate sulfur-sulfur contained in anhydrite and gypsum. Voluntary sulfur-sulfur produced in response to market demand. Basic Sulfur Products: Acid sludge-contaminated sulfuric acid usually returned to acid plants for reconstitution. Brimstone-synonymous with crude sulfur. Bright sulfur-crude sulfur free of discoloring impurities and bright yellow in color. Broken sulfur-solid crude sulfur crushed to -8 in. Byproduct sulfuric acid-sulfuric acid produced as a byproduct of a metallurgical or industrial process, generally relating to combined sulfur sources. Crude sulfur-commercial nomenclature for elemental sulfur. Dark sulfur-crude sulfur discolored by minor quantities of hydrocarbons, ranging up to 0.3% carbon content. Elemental sulfur-processed sulfur in the elemental form produced from native sulfur or combined sulfur sources, generally with a minimum sulfur content of 99.5%. Formed sulfur-elemental sulfur cast or pressed into particular shapes to enhance handling and to suppress dust generation and moisture retention. Frasch sulfur-elemental sulfur produced from native sulfur sources by the Frasch mining process. Liquid sulfur-synonymous with molten sulfur. Liquid sulfur dioxide-purified sulfur dioxide compressed to the liquid phase. Molten sulfur-crude sulfur in the molten state. Prilled sulfur-solid crude sulfur in the form of pellets produced by cooling molten sulfur in air or water. Recovered sulfur-elemental sulfur produced from combined sulfur sources (including byproduct hydrogen sulfide, but sometimes referring only to sulfur from fossil fuels) by any method. Slated sulfur-solid crude sulfur in the form of slate-like lumps, produced by allowing molten sulfur to solidify on a moving belt. Specialty sulfur-prepared or refined grades of elemental sulfur that include amorphous, colloidal, flowers, precipitated, wettable, flour, and paste sulfur. Sulfur ore-unprocessed ore containing native sulfur.

Jan 1, 1994

By Brett Zernich, Michael Krulc, Brett Robinson

This paper provides an account of the efforts undertaken to construct the Northeast Interceptor Sewer (NEIS) project, which is a portion of a much larger program in Los Angeles, California to upgrade the city’s wastewater facilities. The project consisted of a number of elements, including both soft ground and rock slurry wall shafts, drilled shafts, soft ground EPBM mining, rock TBM mining, large diameter pipe placement, and underground structure construction. The need to complete the project under strict schedule constraints, in addition to the challenges of underground construction in congested urban areas, necessitated the work be undertaken with the proper balance of state of the art equipment, and thoughtful planning. The paper will detail the means, methods, and equipment used on the project, as well as discuss several of the unforeseen conditions encountered during construction.

Jan 1, 2005

By D. L. Slyter

Coeur d'Alene Mines Corporation's Thunder Mountain project in Valley County, Idaho, is one of the most remote active mining operations in the US. High altitude, heavy snows, and proximity to wilderness complicate operations in this environmentally sensitive area. Mining is conducted by conventional open pit techniques while processing utilizes on-off heap leaching and Merrill-Crowe zinc precipitation. The project is one of a few similar operations which detoxify the leached ore prior to its removal from the leach pads. Both leaching and neutralizing ( detoxifying) circuits are closed and independent loops. After leaching, alkaline chlorine solutions destroy residual cyanide in the heaps. Calcium hypochlorite solution for the cyanide destruction is prepared by injecting chlorine gas into milk of lime solution.

Jan 1, 1998

By J. A. Herbst

Until the past decade, the energy-size reduction relationship was the dominant form of mathematical model used in the description of tumbling mill grinding processes (1,2). Typically, in these models some single measure of product fineness (e.g. the 80% passing size, the size modules, the specific surface area) is chosen as the dependent variable and the energy input per unit mass of material being ground acts as the independent variable. In some instances these models have been useful for the correlation of experimental data, but, invariably, they have been found to be inadequate for meaningful process simulation. During the last decade considerable advances have been made in the development of phenomenological grinding models derived from population balance considerations (3-7). In these models a set of dependent variables is employed, corresponding to the set of mass fractions which constitute the product size distribution, and energy input is abandoned in favor of "time in the mill" as the independent variable. The phenomenological models have been shown to provide accurate simulations of the entire size distribution of ground products produced in batch (8-10), locked cycle(11)and steady and unsteady state, open and closed circuit continuous grinding(12,13).

Jan 1, 1973

By D. Harney

Accurate measurement, tracking, and planning are vital for efficient utilization of energy in any mining operation, the major focus of this paper. This can be done with a number of assessments: 1) accurately measure KWH usage and track peak demand periods first; 2) identify the electrical equipment that affects your usage and the conditions that require it to be running; 3) remotely monitor and control as much equipment as possible, especially larger pieces of equipment; 4) with your utility determine that you are on the most suitable rate for your usage profile, then understand how your utility company calculates your electrical bill; 5) recognize how production affects energy usage and utility costs; 6) keep historical records of everything you monitor; 7) make information, live and historical, available to everyone; and finally, with the knowledge of your equipment and energy needs, automate controls that you have identified to optimize your energy usage and time of usage.

Jan 1, 2007

By R. O. Y. Breese

The term "diatomite" implies the nearly pure sedimentary accumulation of diatoms. Sedimentary and chemical purity, low density, inertness, intricate fine structure, high brightness and other properties give the diatom and diatomite unique industrial usefulness and commercial value in high value functional filler and specialty filter aid products. Although diatomite deposits occur commonly throughout the world in Miocene and younger marine and lacustrine sediments, deposits that contain significant reserves of crude suitable for these quality sensitive markets are uncommon. U.S. production is centered on exceptional deposits located in Arizona, Nevada, Oregon, Washington and California. Evaluation of deposits requires understanding of geology, mining, production and end use. As crude quality in deposits varies within and between strata, ore suitable for quality sensitive end uses must be identified through sampling and evaluation programs tailored to permit recognition of critical variations.

Jan 1, 1989

By M. O?Driscoll

The tide has turned. Developments in China that have continued to unfold over the last four years or so have now reached a point where the supply market dynamics of certain industrial minerals have changed significantly. No more is this sea change better exemplified than by the supply market for magnesite, and in particular, its processed derivative grades of dead burned magnesia (DBM), caustic calcined magnesia (CCM), and fused magnesia (FM). But what has compounded the barrage of influencing factors impacting this sector, which include the widespread effects of energy and freight cost increases, has been rising demand from certain end use markets. Clearly, the magnesia market is experiencing bittersweet conditions. But those western producers which have monitored and responded to this market transformation, stand to taste success in the near and medium future. REVOLUTION IN WORLD SUPPLY STATUS In essence, while China, as host to a wealth of magnesite resources in Liaoning province, remains a huge producer of magnesia, its supply dominance on the global magnesia market has been considerably weakened. In future, it will mainly aim to supply domestic, and to some extent east Asian markets. Magnesia consumers outside China are now scrabbling for alternative, ?western? sources of supply. At the same time, magnesia producers outside China that weathered the storm of low cost Chinese DBM and FM imports flooding their regional markets for the last 20 years (and many did not), are busy investing in production capacity increases to meet not just demand from falling Chinese supply, but also demand from end use markets which is picking up. And it is not just a matter of expanding capacity of existing magnesia product lines. In the face of plentiful lower cost DBM and FM substitutes from China over the last couple of decades, many western magnesia producers started to switch their focus to the non-refractory markets (eg. environmental, specialities) which promised lucrative opportunities (and still do) and crucially, a lessening of sales revenue dependence on the DBM refractories market. Now we have the likes of Baymag (Canada), Bommag (Serbia/Turkey), and Kumas (Turkey) not only expanding capacities but seriously considering diversifying into DBM and FM production. Perhaps DSP (Israel), having ceased its famous high purity DBM activity as recently as 2005, might even reconsider a return to the ?other side?. But it?s not all DBM and FM. The CCM and specialities markets are also demanding a response, and so Baymag, DSP, Martin Marietta (USA), Premier Chemicals (USA), Qmag (Australia), MGR (Spain), and Magnifin (Austria) are also stepping up to the market on the non-refractory side. From most accounts, the situation with regard to Chinese supply has been described as one of turmoil, with prices rising, leading to improving opportunities for western producers. The majors are conducting huge expansion programmes, such as Qmag, Magnezit (Russia), and the new look Magnesita (Brazil). Even smaller players such as Causmag (Australia) and Dalmia (India) are looking to increase production. In short, the western magnesia supply sector is witnessing a landmark event in capacity investment and market share penetration as China?s previously dominant role begins to weaken (for a review of western capacity expansions see Industrial Minerals, September 2008, p.28). MERGER & ACQUISITION ACTIVITY Another response of course has been a raft of mergers and acquisitions in order to secure resources and supply outside China. These have included private equity groups taking over Magnesita and Qmag; Imerys entering the FM business through UCM; Peñoles further consolidating the electrical grade FM market by acquiring Minco; Martin Marietta acquiring Morton Salt?s Specialty Magnesia Group; Bomex entering the market through Calmag (now Bommag); LWB acquiring Magnesita; and Magnezit?s pursuit of Slovakian magnesia, with Slovmag aboard while currently wooing SMZ. Interestingly, RHI has gone ?the other way?, and has invested in a state of the art joint venture operation at Dashiqiao, Liaoning, with which it aims to secure high quality feedstock for its Chinese refractory plants. Tata Refractories Ltd has announced intentions to follow suit, and other majors, such as Qmag are known to be interested in seeking options. Naturally, there is now renewed interest from several parties in the idled 50,000 tpa DBM/10,000 CCM Jormag facility, Jordan, and the commercially undeveloped Zhargat project, Saudi Arabia. Elsewhere, there will no doubt be suitors for stakes in SMZ, in Slovakia, and Magnohrom, in Serbia, whose respective ownerships are on the block. THE ?CHINA FACTOR? The ?China factor? has been key to magnesia?s market change, and has significantly influenced prices and availability of material to global markets. Resources & production China hosts the largest share of the world?s magnesite deposits, accounting for 26% or 3,319m. tonnes of predominantly sparry magnesite (followed by North Korea, 24%, and Russia, 22%; Wilson 2008). China accounts for 44% of total world magnesite mined (19m. tonnes in 2007) and 50% of the total world magnesia produced (8.2m. tonnes CCM, DBM, FM; Wilson 2008). Russia follows China at 13% of magnesia supply, illustrating China?s dominance of magnesia production. Apart from one producer in Shandong province, central eastern China, the country?s magnesite resources and production are concentrated around the cities of Haicheng and Dashiqiao in Liaoning province, north-east China. Although there are also producers in the Xiuyan district of south-east Liaoning, the Haicheng-Dashiqiao Magnesite Belt hosts the majority of producers. In total these may number 200-300 of large,

Jan 1, 2009