Search Documents

By Felicia F. Peng

Two modes of collector addition techniques are applied in the column flotation for cleaning ultra fine coal. The collector can be: 1) added directly into the coal slurry through the feed system; and 2) gasified collector and transported in the gas phase through the bubbles. Operating parameters of the column flotation were investigated through three phases of work plans for Pittsburgh No.8 seam coal. In present study, the column flotation using two modes of collector addition techniques were tested and compared. Ninety percent or higher combustible recovery can be achieved by using both methods. However, utilizing the gasified collector addition technique in column flotation has more potential than direct liquid addition technique to obtain the higher recovery at same collector dosage.

Jan 1, 1993

By T. Patten

A method for stabilizing mercury containing waste for landfill disposal would be a very cost effective solution for industry. A mercury polythiocarbonate material which is made via a metallurgical process passes a traditional TCLP for mercury. The mercury polythiocarbonate material was subjected to a more thorough evaluation, the Integrated Leaching procedures as described in Kossan (1) and Sanchez (2)The procedure involves leaching the mercury polythiocarbonate material at varying pH and sample size to liquid. The procedure had to be adapted for small sample sizes and finely divided materials due to the product characteristics and available material. The leachates were evaluated and found to be stable within common environmental pH values. The performance details on how Inter-Mountain Labs met the leaching requirements of the procedures and the analysis of mercury are presented.

Jan 1, 2012

By Dean J. Acuff

An overview of new size reduction technology involving the use of two-mass natural frequency vibration applied to a totally enclosed elongated drum. Material moves with a drum-like rotary motion with exposure to constant, aggressive, high frequency agitation for faster reduction and enhanced product quality. A proven, patented design with few moving parts, a vibrating mill drum provides the desirable environmental benefits of a totally enclosed rotary drum but without the same interfacing difficulties. Natural frequency design has reduced energy demand which is met by low horsepower, self-contained, motorized drives to dramatically reduce the cost per ton of finished product.

Jan 1, 1993

By J. M. Smith, T. R. Horton, R. L. Blanchard, T. W. Fowler

INTRODUCTION Uranium mining operations release radioactive materials into both air and water and generate large quantities of solid wastes containing low levels of radioactive materials. Solid wastes produced by mining operations remain on the surface at many inactive mining sites in the Western United States. These mining effluents may present a potential health and environmental hazard. Therefore, Congress, in Section 114(c) of the Uranium Mill Tailings Radiation Control Act of 1978, instructed the Administrator of EPA to prepare a report identifying the location and potential health, safety, and environmental hazards of uranium mine wastes and to recommend a program to eliminate these hazards. Several facts and limitations helped shape the method and approach of the EPA study. Little information on uranium mines was available; measurement information that was available on uranium mine wastes was frequently influenced (biased) by nearby uranium mills; time and resources did not permit comprehensive field studies to provide additional data; and there are inherent variations between uranium mines and sites that complicate generic assessments of mine wastes. To accommodate these facts, the EPA developed conceptual models of uranium mines and made health and environmental projections from them. The models were based upon available data from the literature, supplemented with information from discussions with persons inside and outside the EPA, and by doing several short-term field studies in Texas, New Mexico, and Wyoming. When necessary, conservative (maximizing) assumptions were employed. This paper presents a brief account of a part of the EPA study dealing with the potential health and environmental effects caused by active surface and underground uranium mines. Airborne contaminants are emphasized, although solid and liquid effluents are also included. Due to the limited space, only the methods and parameters used and the results of the assessments will be presented here. Anyone interested in the source of the data used and the development of the parameters should refer to the EPA report (Blanchard et al., 1981). The occurrence and emissions of stable elements were included in the EPA report, however, due to space limitations and their apparent small impact, except for possibly at some specific mines, only radioactive sources will be included in this presentation. MODEL URANIUM MINES The model surface mine was located in the South Powder River Basin of Wyoming and the model underground mine was located in the Ambrosia Lake area of New Mexico. These are the prevalent type mines in those areas. The model mines were based on the average production parameters of the 63 open pit mines and the 256 underground mines that were operating in the United States in 1978 (Department of Energy, 1979) and on a report of an extensive study of open pit mines in Wyoming (Nielson et al., 1979). Information contained in environmental impact statements and in reports from federal and state agencies was also used. Parameters for the model mines are listed in Table 1. The surface mining scenario is that 7 pits are opened in the 17-year mine life with overburden from each successively mined pit used to backfill a previously completed pit, resulting in an equivalent of one pit of overburden (2.4 year production) stored on the surface. No backfilling is assumed at the underground mine. Overburden or waste rock, ore, and sub-ore are separated into separate piles that are either rectangular in shape with length twice the width or in the shape of a frustum of a regular cone. Both shapes have 45 degree sloping sides. To account for bulking, the volume of the material comprising the piles was considered to be 25% greater than the volume of material removed from the ground. It was assumed that dewatering was required at both mine sites. Wastewater discharge rates at the surface and underground mines were assumed to be 3.0 and 2.0 cu m per min, respectively. SOURCE TERMS The following radioactive contaminants at active uranium mines were assessed in the EPA report: 1. Radioactive particulates in a) wind suspended dust from waste rock (overburden) pile, sub-ore pile, ore stockpile, b) suspended dust from mining activities (rock breakage, loading and unloading ore and wastes), and c) vehicular dust, 2. Rn-222 emanation from waste rock (overburden) pile, sub-ore pile, ore stockpile, and mining activities, 3. Rn-222 emanation from mine surface areas, and 4. Radionuclides in wastewater discharged to land surface. Estimated average annual dust emissions (item 1 above) from the model mines are listed in Table 2. Emission factors and the assumptions used to estimate these dust emissions are described in detail in the EPA report. Radioactive source terms were computed for each of the sources; dust emissions were multiplied by the concentrations listed in Table 1

Jan 1, 1981

By Jr. Neudecker

Rock melting technology can provide in-situ glass liners in nuclear waste package emplacement holes to reduce permeability and increase borehole stability. Reduction of permeability would reduce the time and probability of groundwater contacting the waste packages. In-creasing the stability of the storage boreholes would enhance the retrievability of the nuclear waste packages. The rock melting hole forming technology has already been tested in volcanic tuff similar to the geology at the proposed nuclear waste repository at Yucca Mountain, Nevada.

Jan 1, 1989

I met Austin Taylor in Vancouver on my way home from my first Pioneer examination. He asked me to examine the unsuccessful old Lorne mine, adjoining and west of the Pioneer. I had no idea that this meeting would lead to one of the outstanding successes and pleasant associations of my career. I knew nothing of Taylor, except that Gen. McRae and associates said that he had been engaged in lumbering and was interested in an oil and gasoline marketing company called Home Oil. But even if the Lorne examination would be only a small one, in the depths of the Depression in 1931, I was glad to have a chance to look at another gold property, so I agreed to visit the Lorne early in August. The start of the trip was not auspicious. I had been working hard on an unproductive study, and was greatly worried by my father's hopeless illness with tuberculosis. To get a little rest on my way north I had arranged to go from Seattle to Vancouver on the night boat that connected with my train. To my surprise, Bill Boultbee, an associate of Taylor, met me at the train in Seattle at 9:30. He said he would drive me to Vancouver, arriving at one In the morning. I was so tired that I begged off and let him take the drive alone Boultbee was most understanding and friendly, but I knew how I would have felt if I had been kind enough to take the long drive to help a stranger and then had been forced to make the return midnight drive alone. I was lucky they did not call off the examination at once. I got a good sleep on the Vancouver boat and Austin Taylor met me at the Hotel Vancouver for breakfast. After a brief talk he took me to the small steamer that made the 4-hr sail up Howe Sound to the village of Squamish. This was the end of the Province-owned Pacific Great Eastern Railway that was eventually to be a shortcut from Vancouver to the Canadian National main line at Prince George. Because

Jan 1, 1976

By L. Eros, R. H. King

The US Bureau of Mines has funded several research and development projects in computerized mine monitoring and control. Hardware and software components have been sufficiently developed so that mine operators have been provided with an efficient means to comply with federal regulations and increase mine safety. Several cost benefits have been realized as well, particularly with increased conveyor belt haulage availability. Western Fuels-Utah Inc. approached the Bureau to assist in planning, installing, and evaluating a computerized mine monitoring and control system because of the agency's research experience in this area. The installation was planned for Western Fuel's Deserado mine, located in Rangely, CO. Since a large, complex, underground mine producing about 2.4 Mt/a (2.7 million stpy) of coal was projected, the company anticipated significant benefits in safety and efficiency through a computerized monitoring and control system. A major part of the cooperative program was to document and evaluate the system design, installation, and operation. This will assist others to adequately design, specify, install, and operate future systems. Mine description The Deserado mine plan and layout have important impacts on the monitoring system requirements. Long range plans are to produce 2.4 Mt (2.7 million st) of clean coal annually from two longwall sections and four continuous sections. Presently, two continuous miner sections operate under 213 m (700 ft) of overburden in the 2.3 to 2.5 m (7.5 to 8.5 ft) thick D seam to develop main, submain, and panel entries have developed for a longwall. These began operation in December 1986. Belt conveyors haul the coal from the mining sections to a 1.4-m (54-in.) belt located in the upper compartment of the slope. The lower compartment contains a hoist for men and material transport. From the slope, the coal moves to two 9 kt (10,000 st) raw coal storage silos, then to a 680-t/h (750-stph) preparation plant. After cleaning, a 5.5-km (3.5-mile) overland conveyor carries the coal to a clean coal slot storage and rail load-out facility. An electric locomotive then transports the coal to the Bonanza Power Plant in Utah. Allen-Bradley monitoring and control hardware and software controls the preparation plant, with two PLC-3 programmable controllers and a Process Control Industries D-1200 color graphics interface. The system operator uses three "smart" color video display units and an alarm printer for hard copy records. Originally, it also monitored and controlled the conveyors from the bottom of the slope to the top of the raw coal silos, the preparation plant, the overland conveyors, the main mine ventilation fan, and the hoist. Some of these features, though, were later transferred to the mine system.

Jan 2, 1988

By NEHA PANDEY, V.K. REDDY KALLAM, SUNIL KUMAR TRIPATHY, ARIJIT BISWAS

This work discusses the sulfur dioxide (SO2) leaching of low-grade ferruginous manganese ores to selectively recover manganese (Mn) as manganese sulfate (MnSO4), followed by electrowinning of the purified MnSO4 to produce electrolytic manganese dioxide (EMD). The effects of the leaching process parameters on Mn recovery were studied, and the leaching duration and SO2 flow rate were found to have significant effects. Under the optimum conditions derived for grade 1 ore (with total Mn content of approximately 17.16 percent), the specific SO2 requirement (SSR) — that is, the SO2 flow rate per gram of Mn in the leach slurry — was calculated to be 0.014 L/min. At the SO2 flow rate calculated using SSR for grade 2 ore (with total Mn content of approximately 26.29 percent), a Mn recovery rate of 94 percent was realized. Electrowinning of the purified MnSO4 generated after leaching resulted in EMD with 88.01 percent purity and a γ structure.

Sep 1, 2022

By M. S. Duffy

To exploit the mineral resources of fine grained ore bodies the minerals processing industry is turning to fine grinding technology, of which tower milling has become an established part. However, compared to other mills relatively little is known about the operating mechanisms in tower mills. In all milling processes one of the keys to understanding how they work is in knowing how their grinding media move. To investigate the ball motion in tower mills a glass unit was therefore constructed and measurements taken of the movement of the grinding media. This paper describes the results from this study.

Jan 1, 1998

By John R. Twining, Michael D. Lawton, Ross A. Jeffree

The Finniss River system in tropical northern Australia has received 'acid-drainage' contaminants from the Rum Jungle uranium/copper mine site over the past 4 decades. Following mine-site remediation that began in 1981-82 the annual contaminant loads of sulfate, Cu, Zn and Mn have declined by factors of 3, 7, 5 and 4, respectively over 1990-93, compared to the 1969-74 pre-remediation loads. Comparison of the frequency distributions of contaminant water concentrations over these pre- and post-remedial periods have shown varying degrees of reduction in the highest levels following mine-site remediation, that are consistent with reductions in their annual-cycle loads. Among the three selected major metal contaminants the reductions in maximum water concentrations are most pronounced for Cu. The demonstrated reductions in the highest water concentrations of all four contaminants are also associated with previously reported ecological improvement in the Finniss River system, compared to the benchmark of environmental detriment established in 1973fl4, prior to the beginning of remediation at the mine site.

Jan 1, 2000

In general, it cannot be assumed that the strength of coal pillars remains constant over long periods of time. Field observations indicate that a coal seam, especially when it contains a parting layer, deteriorates over time, reducing the load-bearing capacity of the pillars. This paper discusses a unique approach to determining the time-dependent strength of coal pillars in the field. Three coal pillars that were developed 5, 15, and 50 years ago were chosen for the study. Holes were drilled in coal and parting layers in each pillar, and the strength profiles were determined for each hole using a borehole penetrometer. The strength data were treated statistically to establish time-dependent strength equations for different layers. The results can be used to help estimate the loss of pillar capacity over time.

Jan 1, 2012

Over the past few years, the School of Mines of Paris has carried out a program of research* on the grade-tonnage relationships in the border zones of porphyry copper deposits. The initial problem was quite difficult : how does the grade vary at the border of the known orebodies? Does it decrease regularly, or do some thresholds exist, where the grade diminishes abruptly? The answer to these questions have important repercussions on the prediction of the future reserves in the fringe of the orebodies. If the grade decreases regularly, very important reserves could exist; if not, there would be strong limitations to the possible recoverable reserves. The first step of our study was a critical study of previous work done on the subject. It appeared that, following Lasky's pioneering paper (Lasky, 1950), most of the authors used what we can call an historical approach to the problem. In this, the grade-tonnage relationships are calculated from the available figures for production and reserves and the results are then extrapolated to the future. The strong limitation of this model are brought out in this article.

Jan 1, 1982

By Armando Alatorre

The Republic of México is the world's largest producer of celestite/strontium carbonate and natural sodium sulfate. It is also a significant producer of flourspar, barite, graphite, sulfur, feldspar, salt and gypsum. New production may be brought on stream for borates, wollastonite, garnet, calcium carbonate and others. The country covers a geographic area of approximately 2 million square kilometers (760,000 square miles), and is divided into seven geological/geomorphological provinces. Less than 20 percent has been explored in detail for either nonmetallic or metallic minerals. This leaves large areas available for the discovery of world-class industrial mineral deposits. In addition to new deposits of those minerals currently being produced, there is exploration and development potential for borates, magnesite, rare earths, nepheline syenite, heavy mineral sands and numerous others.

Jan 1, 1995

By Liuming Wu, Willis Forsling

The complexation of Alizarin Red S (ARS) at the surface of hydrous fluorapatite particles has been investigated at 25.0 C by means of potentiometric titrations, adsorption experiments in 0.1 M NaCI ionic medium, and Diffuse Reflectance Infrared Fourier Transform spectroscopy (DRIFT) studies. A chemical model describing the reaction at the aqueous mineral surface has been established under equilibrium conditions according to the reaction [== -CaOH2 + HA2 - « _ =PO CaA2 - z + H30&apos;; to (int.) = -5.61 ± 0.02 3 a =PO- logBs-1110(int.) ( ) within the range 8.40 <_ -log[H ] <_ 9.80.] Experimental data were evaluated using the computer program FITEQL on the basis of a constant capacitance model for the electric double layer. The surface complex structure, has been proposed to involve the quinoid and alpha phenolic oxygens of ARS coordinated to the calcium sites on the fluorapatite surface.

Jan 1, 1993

By N. Arbiter

Introduction The theoretical analysis of tumbling mill energetics and performance has largely neglected mill dimensionality, and, in particular, the importance of the length/diameter (L/D) ratio. This is in spite of the fact that practice varies substantially: geographically, for semi-autogenous and autogenous mills, as between North America and South Africa/Scandinavia, and historically, for overflow ball mills, for which the L/D ratio has increased significantly from the earliest small mills to the largest mills currently. The present study is concerned primarily with the influence of the L/D ratio on the design and operation of overflow ball mills, on the occurrence of the overload phenomenon, and on the limits, if any, it may impose on mill capacities because of critical pulp axial velocity limits. It will be shown that the shape factor is of major importance in this area and that its adjustment to the extent that this is practical should remove the diameter limitations previously postulated for this mill type. Dimensionality in mill design Ball mill shape factors in the period prior to 1927 (Taggart, 1927) averaged 1.1/1 for 29 center discharge mills and 1.0/1 for 30 peripheral discharge mills. With the resumption of new plant construction after the 1930s depression, the Morenci concentrator continued the 1/1 ratio with its 3.1 x 3.1 m (10 x 10 ft) mills. The ratio was increased progressively from then on, reaching 1.6 and 1.8/1 for the largest overflow mills currently. As shown recently (Arbiter, 1989), this is in sharp contrast to autogenous and SAG mill shapes, for which the ratio averages 0.4 in North America. On the other hand, South African practice, starting at the turn of the century with autogenous mills having 4/1 ratios, moved toward 1/1 until recently, when a 2.5/ 1 ratio mill was installed. The reasons given for such divergent practice for mill shape factors are in some respects contradictory and generally inconclusive. The most complete discussion from a practical viewpoint (Dor and Bassarear, 1982) is limited to primary SAG and autogenous mills. Considerations of ball mill dimensionality have had a twofold direction. On the one hand, it has been argued that ball mill efficiencies should increase with increasing diameter and that the specific energy for a particular grind should be reduced accordingly. An inadvertent test of this idea at the Bougainville operation (Burns and Erskine, 1983) resulted in drastic underpowering, which led to failure to reach design capacity until additional mills were installed. This can be taken as strong evidence against any increase in efficiency with diameter. In another direction, it has been argued (Arbiter and Harris, 1982, 1983) that there is a limit to ball mill diameters because of the demonstrable limit to axial flow velocities evident in the overload phenomenon, which as a fact is incontrovertible. But that it places a limit on mill diameters overlooks the evidence given below that appropriate variation in the L/D ratio will permit major increases in diameter, limited only by constructional or economic factors. The present study was directed toward quantifying the overload phenomenon through examination of the influence of mill dimensionality variation and mill operating variables on its occurrence. It is shown that varying the operating conditions, specifically the load fraction and the fraction critical speed, can reduce the risk of overload for existing operations; while appropriate decreases in the L/D ratio can minimize the risk in the design of new circuits. Ball mill overload Ball mill overload is a consequence of the approach to a critical velocity with increasing feed rates or circulating loads. Although the effect has been known for over 50 years, there have been no previous attempts to quantify it. The following description of the ball mill as a flow system is the preliminary to a quantitative analysis: 1) In the absence of a ball load, axial flow of pulp through a mill resembles open channel flow, except for disturbances near the shell due to shell/lifter rotation. 2) For a given ball load (Lf), the void fraction available for pulp hold-up (H) for the ascending portion of the load is approximately 0.4 Lf. In the descending portion, it is greater than this and increases with fraction critical speed (Fc) because of load expansion. 3) Increasing the feed rate increases pulp hold-up and progressively fills the available void space. At a critical flow rate, which depends on system geometry, hydraulic head and pulp rheology, void filling reaches its limit; a pool forms rapidly and fills available space outside the ball load and up to the overflow level. Prior to this, pulp discharges mainly along the ascending rim of the overflow. 4) For a small mill (Lo et al., 1990), it has been shown that with increasing feed rates the critical filling is at or near 50% of the mill volume. Power drops rapidly when this level is reached, as required by the torque formula. 5) The transition to overload is associated with the following phenomena: a) The decrease in power draw. b) Damping of mill sound. c) Reduced comminution of coarser feed sizes, probably due to reduced direct impact in the presence of a pool. d) Increased circulating loads, which further intensify the overload, and increased density of cyclone underflows, which can lead to roping. e) Conditions beyond overload are not known because feed rates are not delibelrately increased beyond this point. f) The existence of the phenomenon limits the capacity of a mill with a fixed set of operating conditions and can prevent the balancing of hard ore feed rate decreases by increases in soft ore rates.

Jan 1, 1992

By David Green

Power point slides

Jan 1, 1999

By Vladimir L. Konyukh

Robotics is topical for mining owing to deterioration of miner&apos;s safety as a depth of winning, limited functions of traditional mechanization and automation, rise of miner&apos;s labor cost. Mining robot is an autonomous mining machine with a free programmable control that provides a multifunctional use of working head. After analysis of world publications the database “Technological applications of robotics in mining" has been built. In most cases robots are suggested for imitation of miner&apos;s motions. The following shapes of robotics had been classified for mining: technological robot as a flexible controlled mining machine, remote manipulator, mine rescue robot. The problems of both non-repeated environment recognition and telepresence without direct visibility must be solved. The more a robots integration is the less investments and the more efficiency are. Computer simulation of robotics-based mining is founded on a base of 6 robots functional models, Petri nets and library of 30 robotized technologies. There are some examples of mine robotization in the paper.

Jan 1, 1996

By John E. Husted

Universities have education as their primary purpose. This appears to be an innocuous statement with simple meaning. In an age of conflicting semantics, however, cords and meanings are often lost or changed. The term education is often broadly expanded to encompass any form of learning process, or the accumulation of knowledge, and even to the beneficial application of knowledge to man&apos;s problems, hence one find that education in universities is not solely the formal process of texts, lectures, recitations, and testing by a batch process known as class room teaching. Despite critics of education batch is spelled with an "a", instead of an "o" - at least we hope so If one defines teaching as causing to learn, then the learning objectives may necessitate a variety of approaches within the teaching concept and research is among those favored at the graduate and some undergraduate levels. Research has been among the glamour words and certain fields such as oceanography and space science have had more than their share of glamour. Unfortunately, industrial mineral research has not had the competitive drawing power of enamoring students of the "note" generation in terms of glamorous accomplishment. Research today usually requires sophisticated equipment and such equipment is expensive, both for initial purchase and operation. Again, administrations, be they industrial, government, or academic, usually require

Jan 1, 1970

By Timothy M. Bruner, William J. Maloney

Faced with rapid growth that strained their current water supply capabilities, the Somerset Water Service in Somerset, KY decided to construct a new intake structure on the shore of Lake Cumberland. With an existing intake structure within 200&apos;, very hard limestone geology with calcite geodes, and lake level fluctuations as high as 50 &apos; ,this project posed many challenges. The following paper discusses how mechanical excavation techniques were used to overcome these obstacles.

Jan 1, 2001

By G. Kim

The influence of bacterial growth phase on the flotation behavior of malachite has been investigated in a well-controlled Hallimond tube system. The microflotation tests were conducted for malachite (45?53 µm) using different amounts (bulk phase concentration=1×108?5×109 cells/mL) of Rhodococcus opacus (R. opacus) as a collector, which was grown at mid-exponential versus stationary phase, at a constant speed (340 rpm), pH (6), and malachite-bacteria interaction and flotation time (each 10 min). Hug differences between R. opacus cells in mid-exponential and stationary phase was observed from the results for electrophoretic mobility and flotation tests. Specifically, the isoelectric point of the cells in the stationary phase was lower than that in the mid-exponential phase, suggesting that the amount and distribution of surface functional groups onto cell surfaces are likely different. Additionally, the cells in stationary phase led to significant increase in the flotability compared to those in mid-exponential phase over the background bacterial concentration level of 1×108?5×109 cells/mL. Furthermore, the flotation efficiency tended to increase with increasing cell dosage for stationary phase cells while no distinct difference was observed for mid-exponential cells.

Feb 27, 2013