Search Documents

By Steve Jones

Minor subsidence damage to the Burgettstown Junior-Senior High School building and grounds near Burgettstown, Washington County, Pennsylvania, prompted an investigation of the site in early 1985 by the Bureau of Abandoned Mine Reclamation of the Pennsylvania Department of Environmental Resources. The investigation determined that subsidence over an abandoned coal mine was occurring and that additional damaging subsidence would occur if reclamation measures were not taken. A Pittsburgh Coal Seam Mine which was abandoned in the 1920's underlies the school at a depth of sixty-five (65) feet. This sixty-five foot section is comprised of five (5) feet of unconsolidated overburden and sixty (60) feet of thinly bedded, highly fractured shale. Approximately five and one-half (5-1/2) feet of Pittsburgh Coal was extracted at the school site. A thin shale binder and one (1) to one and one-half (1-1/2) feet of roof coal were left in place. Within the Contractor's Underground Working Area (See Figure 1) approximately thirty (30) percent of the coal was extracted. It appears that the mine was just being developed in the vicinity of the school when it was abandoned for no known reason. Other nearby portions of the mine show extraction approaching sixty-five (65) percent.

Jan 1, 1986

By Mitchell J. Willis

Recovery of fine particles has been considered to be a major limitation of the classical flotation process. However, the beneficiation of kaolin, a naturally occurring fine ore, via flotation has been practiced over the last 40 years. Kaolin is valued as a white pigment, and therefore, the goal in kaolin flotation circuits is to remove the colored impurities to result in an acceptable brightness product. Kaolin flotation originated with a novel carrier flotation process, and later on carrier less flotation techniques were developed. The collector chemistry utilized to beneficiate kaolin is based on fatty acids, and recently hydroxamates have been successfully used. The purpose of this paper is to cover the flotation practice in the kaolin industry in terms of the history and the reagent schemes.

Jan 1, 1999

By L. A. Hansen, D. L. Buffington, G. H. Beckwith

This paper reviews geotechnical engineering considerations in heap leach pad design, discusses design philosophy and provides design procedures. A brief discussion of surface water hydrology ground- water protection and other design considerations are also presented. Special emphasis is placed on projects in the arid and semiarid regions of the Western United States where annual evaporation exceeds rainfall, and where good foundation conditions are usually present.

Jan 1, 1987

By David M. MacGillivray

1. INTRODUCTION The economic importance of bringing a new mine to production in the shortest possible time, is well known. In recent years the rate of escalation of mining costs has accelerated more rapidly than at any time in the past. This fact has enhanced the need to reduce time schedules and made it an overriding and predominant objective when planning new shafts. The squeezed profit margins and widely fluctuating metal prices have also increased the emphasis being placed on this aspect. Moreover the increase in the present value of future profits due to the reduction in the time element, can be so substantial that expenditure on equipment and additional labour can be justified conditional on sufficient gain in shaft sinking speed being achieved. The emphasis on time saving becomes more abundantly clear when considering the very large increase in the capital required to bring a modern underground mine to production. As an example, the initial capital expenditure requirements for a large new gold mine in the Western Transvaal, which has commenced production recently, is estimated at R200M, and a major extension to another deep level mine in the same area is estimated at R300M. With the uncertainty of future metal prices and the recent trends in increasing inflation, it is becoming more difficult than ever to estimate the profitability of proposed mining projects and any cost saving due to more rapid sinking of shafts can only assist in this respect. Since the shaft systems are frequently the most expensive set of underground excavations and no other underground work can commence until they are completed, the speed of shaft sinking is subject to closer scrutiny than in the past. In the following sections of this paper the factors contributing to the high average advance rates achieved by South African shaft sinkers are discussed. It is difficult, if not impossible, to estimate the effect of any single factor, in isolation, on the overall sinking achievements. However, the cumulative effect of improvements made in the inter-related activities is, probably, the most important contributor. Although there has not been any single major technical change or innovation to shaft sinking practices in the last decade, the average sinking speeds have increased, due to improved application and technical improvements in established procedures. 2. GENERAL When discussing South African shaft sinking techniques and average sinking rates compared to those achieved in other parts of the world, it should be remembered that the size and depth of South African shafts are often considerably greater than in most other countries. Typical examples of shafts either in the course of sinking or recently completed are -

Jan 1, 1979

By Osvaldo Bascur

Large metallurgical complexes have more data than a small city and much of it is "real time," changing rapidly as internal and external conditions evolve. As corporations buy and sell assets and reengineer their staff, the structures and tools that were used to understand these data are lost. This results in significant deterioration in the ability to maintain a "smart" operation. The solution is to use the sophisticated new tools built for the Internet so as to leverage information in a familiar browser format that people can use and understand. This paper describes the use of Internet technologies with plant data. Examples are drawn from existing industrial sites. Users must project where this technology will lead - standing still is the most dangerous philosophy and the only one guaranteed to be obsolete. These examples show the way to leverage existing workers with information technology.

Jan 1, 2000

By Nikolas K. Sokol

Underground construction often requires working within a very congested urban environment, including excavating shafts adjacent to highly sensitive and multistoried structures, sometimes even within such structures. Shafts adjacent to heavily loaded column footings are often required due to space constraints. Invariably, footing surcharges must be considered during the design of shaft rock reinforcement. Rockwedge stability evaluation reveals that column surcharges can greatly impact the ability to meet the desired factor of safety. Design methodologies and examples to deal with these special circumstances are presented.

Jan 1, 2008

By G. Tiess, S. Mujiyanto

Indonesia is a fast growing democratic developing country comprising more than 17,000 islands, founding member of ASEAN and a member of the G-20 major economies. It is one of the most highly mineralised countries in the world, the mining sector playing a pivotal role in the country's economy. In 2001, the Decentralization Law No. 22/1999 came into force and caused a transfer of authority and responsibility from central to regional and local administrative governments. The new Mining Law of 2009 substituted its 40 year old predecessor, but lacked detailed regulations for its implementation. These were only issued in 2010, which lead to a period of great uncertainty for investors in the mining industry. The new legislation intends to foster domestic economic development, which may be interpreted as protectionist policy. For the development of a sustainable mineral resources policy, further endeavours will have to be made.

Jan 1, 2011

By Manuel Diaz del Rio

At the present time there are over 5,000 Kms of railway tunnels in existence throughout the world. In many cases these tunnels were built over a century ago using techniques obsolete today. Supervision and maintenance of these tunnels is essential to the economy of each country involved. For this purpose an electro-optical measuring system has been designed incorporating highly complex soft and hardware (15 mW laser, high resolution TV camera and processing computer), mounted on a vehicle. Its job is to scan, record and compare sectional gauge values (profiles) and strains inside tunnels both momentarily in situ and on permanent record, as an aid to the supervision work. From the state of the strains observed, in conjunction with an infrared spectrum of the tunnel lining and soil involved, the mechanical stresses in the tunnel can be deduced by applying the boundary elements method.

Jan 1, 1981

By Hugh E. Cronin, Lok Home

THE PENETRATION RATE BASELINE DILEMMA The penetration rate is the instantaneous advance rate of a TBM in a rock tunnel. Normally expressed in feet per hour. The production rate is the penetration rate multiplied by the number of hours worked and then factored by the actual utilization of the TBM. In a given rock formation, the actual production rate is a result of many factors some of which are within the control of the contractor and some of which are based on the route selected. Factors that are within the contractors control are cutter profile, frequency of cutter changes, thrust, rotation speed, cutter spacing and the efficiency of the operation. Factors that are site (route) specific are compressive strength, fracture orientation, fracture frequency, micro- fracturing, quartz content, Moh’s hardness, Cerchar Abrasivity Brazilian Tensile Strength and Youngs Modulus of the rock. In addition the following route speci?c conditions are beyond the contractors control; rockjointing, rock stress fault zones, water in?ow and rock decomposition; all of which effect production rate. Any one of the above defined rock properties, equipment specifications and actual operating usage will change the penetration rate. Furthermore, since the rock formation changes both in content and orientation as the tunnel advances, the penetration rate is constantly varying. The current industry practice in bidding tunnels is for each contractor to individually evaluate the rock hardness and other properties and from this information develop a penetration rate. All other factors being equal, the contractor using the most optimistic penetration rate will be the low bidder and be awarded the project. As this view is by definition optimistic, invariably the rock will be harder than the low bid assessment and the contractor will request additional compensation for the changed condition. The contractor will attempt to justify his optimistic assessment as reasonable by using expert supporting analysis. The above described example which is quite common at present in the industry tends to make the most optimistic contractor (at time of bidding) the contractor selected for the project whereas it is in the owners interest to contract with the most efficient contractor not the most optimistic. This situation is similar to the Geotechnical analysis that was prevalent in the industry over twenty years ago. Many projects have experienced a significant reduction of penetration rate from that which was originally estimated. In these cases the contractor often makes a claim for extra compensation based on the difference between the actual rock encountered

Jan 1, 2003

By Erik Westman, Enji Sun, Xu Ma, Ben Fahrman

"Shale gas has become an increasingly important clean energy, which has been explored worldwide in recent decades. Supercritical CO2 acts as fracturing fluid for shale gas production. The safety monitoring is essential to prevent any kinds of leakage from the reservoir as the supercritical CO2 physically stored hundred kilometres underground. Seismic tomography is an imaging technique that uses induced seismic waves to create three dimensional images of the subsurface. It is an effective monitoring method to evaluate the caprock integrity in the carbon dioxide sequestration storage (CCS). In this experimental research, a simulated uniaxial compressive load is applied on a granite sample to analyze the stress redistribution for long-term in-situ caprock integrity during CO2 injection. The induced seismic waves are recorded and seismic events are traced based on the Geiger algorithm. The frequency of seismic events correlates with the caprock failure evolution. The acquired seismic data is divided into four regimes based on the frequency of seismic events and the failure process to examine the failure evolution. Furthermore, the travel time and distance is plotted to analyze the variation of velocity. Finally, the double difference tomography (TomoDD) algorithm using arrival time is adopted to recalculate the locations of seismic events and velocity structure in each regime. The results indicate that the passive seismic system can map the caprock stress distribution and allow for imaging of the caprock integrity. TomoDD exhibits sound improvements to relocate seismic events both in relative and absolute locations as well as to characterize the local velocity structure. The study further reveals that seismic monitoring along with TomoDD could evaluate the caprock failure accurately in the CCS.Introduction To reduce the CO2 concentration in the atmosphere, CO2 capture and sequestration (CCS) has been suggested to as a means of continuing to use fossil fuel resources while offsetting their negative environmental impacts (Eiken et al 2011). A positive CCS project should retain 99% of the injected supercritical CO2 (pressure is greater than 7.38 MPa and temperature is above 31.04? and a density is of about 700 kg/m3) over at least 100 years (Davidson et al 2005). As large quantities of supercritical carbon dioxide are being injected into full scale storage projects, caprock stress is redistributing and the leakage could occur anywhere over a wide storage area (Hou et al 2012). Acoustic waves are emitted from the caprock, as it fractures due to the CO2 injection, which can be detected by passive seismic sensors (Shitashima et al 2013). Tomography techniques are advantageous for imaging the integrity of the caprock in the CCS projects. Velocity tomography uses waves to model entities based on the arrival time of waves (Westman et al 2001, Westman 2004, Luxbacher et al 2008). Seismic tomography is a data inference technique that exploits information contained in seismic records to constrain 2D or 3D models of the Earth's interior. It generally requires the solution of a large inverse problem to obtain a heterogeneous seismic model that is consistent with field observations (Kudryavtsev et al 2012)."

Jan 1, 2017

By G. Deschenes, W. Yen

Ammonium thiosulphate is a non-cyanide lixiviant for gold leaching. The major problem is the high reagent consumption. A combination of 0.3M (NH4)2S2O3, 0.03M CuSO4, 3M NH3 was used to leach a copper-bearing gold ore at pH 10.2 for 24 hours. 30 kg/t of thiosulphate was consumed. Oxygen and copper species were found to be responsible for thiosulphate decomposition. The thiosulphate consumption could be reduced to around 17 kg/t by adding chelating agent, reducing copper sulphate concentration to 0.001 M and replacing CuSO4 by NiSO4. The increase of pulp density might reduce the thiosulphate consumption to around 17 kg/t. By regulating the oxygen supply, the thiosulphate consumption could be reduced to 10 kg/t.

Jan 1, 2002

By J. L. Osiensky, R. E. Williams, J. Linehan

The hydrostratigraphy of uranium in situ leach sites consists typically of interbedded layers of sand, silt, clay and gravel deposited by fluvial processes. 'These layers usually form leaky multiple aquifer systems where sand and gravel aquifers are separated by silt or clay confining layers (aquitards). It is very important to evaluate the hydraulic properties of the ore zone aquifer and the confining layers by aquifer pump testing to ascertain the effects that in situ leach mining will have on the multiple aquifer system. The degree to which current methods of aquifer pump testing will provide the information necessary to adequately characterize the hydraulic properties of the ore zone aquifer and its confining layers is dependent upon the hydrostratigraphic conditions at the site and the limitations of the testing methods. The primary objectives of the aquifer testing program should be to evaluate the vertical hydraulic conductivity of the confining layers and to quantify leakage into or out of the ore zone under mining conditions.

Jan 1, 1984

By S. Shrivastava, R. G. Reddy

Spent potliner is generated in the electrolytic process of reducing alumina to make aluminum metal using molten fluoride electrolytes. Spent potliner (SPL), obtained at the end of the pots life contains a small amount of cyanide and fluoride which present environmental problems. SPL became a listed hazardous waste under RCRA (KO88) in July, 1990. One of the possible uses of spent potliner is as a substitute for Calcium Fluoride (CaF2) as a fluidizer in iron- and steelmaking and in the glass industry. A low viscosity and a low melting point are prime requirements for accomplishing the above. In the present study, viscosity measurements were performed. Effect of various additives, such as sand, limestone, dicalcium silicate dust, and MgO baghouse dust on the viscosity of SPL was studied. The results showed that with the addition of sand and limestone, very high fluidity of SPL melt can be obtained at significantly low temperatures. The results suggest that spent potliner mixed with additives could potentially be used as a substitute fluidizer.

Jan 1, 1999

By C. Haycocks

The Appalachian coal fields contain many mineable contiguously placed coal seams. Selection of the mining sequence for these seams, historically and currently, is based primarily on considerations of seam ownership, availability and economics. Mining any seam can seriously affect subsequent operations in coal seams both above and below the one being mined. The effect is often detrimental to recovery costs and safety of mining in the subsequent seams. The purpose of this paper is to examine the conditions that can develop in an underlying seam due to stress concentrations that can occur below pillars or abutment zones in an overlying seam, and suggest guidelines for avoiding them. This situation most commonly occurs when the overlying seam is mined first, although simultaneous and subsequent mining of the upper seam can also produce such effects. Other interaction phenomena resulting from subsidence or arching will not be considered here. The methodology used in this research utilized both computer and body loaded photoelastic models to study the interaction mechanisms. Field studies are used in both interpretation and analysis of the results. Numerous examples of load transfer from upper workings exist in all parts of the world and many of these have been incorporated into this work. Such interaction problems are quite common and likely to be an ever increasing occurrence as mining activities in old seams are completed and new seams opened up.

Jan 1, 1982

By G. Tapia, R. J. Kelley

Empresa Minera de Mantos Blancos S.A. successfully commissioned two copper SX-EW plants in late 1995. The design of these solvent extraction plants is such that chloride tenors of 30-35 g/l can be tolerated in the leach solution with no contamination of the electrolyte. The design was carried out in conjunction with Bechtel-ARA engineers and was based on the successful application of the available technology in the market; this mainly focused on decreasing the aqueous entrainment in the organic phase. This entrainment can reach 20,000 ppm in conventional plants.

Jan 1, 1998

By B. J. Sauer

Variable frequency drives (VFD’s), or adjustable frequency controls (AFC’s) as they are more precisely identified, have been available to the mining industry for over 20 years. However, in recent years as the push to cut production costs has become ever so crucial, AFC usage has become more widespread. This paper seeks to provide professionals in mineral processing plant design and operation with an introduction to AFC’s, insight as to why AFC control for AC induction motors can be advantageous, and specification and design considerations.

Jan 1, 2002

By B. Salopek

The greatest part of crushed stone, gravel and sand production is extracted through open pit operations, whereas gravel and sand are also partially extracted from riverbeds. Its obvious that such a mining activity provokes some changes in the configuration and environmental characteristics of the region, in the temporary or permament disapperance of vegetable or animal species and in the creation of noise, dust and waste water. However, the above-mentioned mining operations shouldn not have only negative effects on the landscape and land potential, but they can discover and predetermine the potential of the exploited areas for various communal purposes after exploitation (eg. sports and recreation centers, campsites, resorts, fish-farms, etc.). In this paper, the production of construction aggregates in plants located in the vicinity of Zagreb, the capital of Croatia is presented. The advantages and disadvantages of aggregates? production in urban areas in the spirit of sustainable development are discussed.

Jan 1, 2003

By G. T. Adel

The flotation behavior of a -28 mesh Pittsburgh No. 8 coal sample is investigated through the use of Scanning Electron Microscopy in conjunction with Image Analysis. Release analysis is used to generate the flotation products, which are then characterized to provide the particulate composition in terms of pyrite, mineral matter and carbonaceous material. The results of this investigation indicate that the material recovered in the first stage of release analysis tends to be well-liberated carbonaceous material. This is followed by an increase in the recovery of middlings and fines in the later stages of the process. Any free carbonaceous material remaining in the tailings from the release analysis test tends to be associated with the very fine sizes (-400 mesh). Pyrite recovery is attributed to the hydrophobicity provided by small inclusions of carbonaceous material, since the amount of truly liberated pyrite particles (i.e., 100% pyrite) present in the sample is found to be negligible.

Jan 1, 1994

By S. K. Kawatra, T. C. Eisele

Under normal conditions, a significant amount of pyrite is recovered in the froth during flotation of high-sulfur coal. To reduce this pyrite recovery, it is first necessary to determine the primary recovery mechanism, because different measures are required for reducing entrainment, locked particle flotation or true hydrophobic flotation. In this paper, evidence is presented that suggests that hydrophobic flotation is not the major mechanism for recovery of liberated pyrite; instead, the bulk of the recovered pyrite results either from simple entrainment or from being physically locked with floatable coal particles.

Jan 1, 1993

By A. Athousaki

The Ecological Footprint is a resource accounting tool used to address underlying sustainability questions. Aggregates consist of natural, artificial or recycled materials. The production of aggregates is the fastest growing activity worldwide since huge quantities are required by the construction industry. This paper presents a parametric investigation of the ecological footprint of transporting aggregates for urban use as a function of tonnage and distance.

Jan 1, 2008