Search Documents

By W. Hitchcock

To enable the analysis of stability for a mine feasibility study a variety of geotechnical engineering parameters need to be obtained. At the early stage of a project it is usual for those responsible for the study to require a wide spatial distribution of RC holes in order to define a resource at the lowest possible cost. By the time a geotechnical study has commenced drilling priorities have usually switched to improving the definition of a resource, by drilling with diamond coring methods in the central area of the main orebody. The usual timing for geotechnical data collection is therefore after a wide distribution of holes have been drilled but which contain little geotechnical information. Conventional methods employed usually involve estimation methods, including book values and examination of disturbed core, or expensive additional drilling. With downhole geophysical methods we can economically take advantage of existing holes to obtain continuous values for density, defect orientation and ranking, elastic modulus values, unconfined compressive strength estimates and fracture frequency. This paper presents the results of a geophysical study and discusses the advantages and potential pitfalls of the method as compared to conventional methods of data collection.

Jan 1, 1999

By B. J. Arnold

Coal blending inherently means homogenizing a mixture of coals so that, overall, the properties of the blend meet some specifications for maintaining power plant performance and emission requirements. In common practice, however, coal blending is at best coal mixing. If necessary, more sophisticated blending systems can produce a more homogeneous feed by using accurate weighing devices and on-line coal analyzers coupled with sampling systems. Blending can be accomplished at the mine, on stockpiles, and from bins, bunkers, and silos.

Jan 1, 1994

By Ashish Ranjan Kumar, Barbara Arnold, Luis Sanchez Gonzalez

Mining operations adopt a variety of measures to combat dust underground. These include ventilation systems, water sprays, physical barriers, and personal protective equipment (PPE). Respirators are a class of PPE that can provide clean particulate- free air to the users. Powered Air-Purifying Respirators (PAPRs), used commonly in medical and other sectors, are not prevalent in the mining industry. PAPRs use P100 filters that have 99.97% dust capture efficiency. We present our results from computational fluid dynamics (CFD) simulations performed to understand the impact of a PAPR on airflow and dust particle concentration in the vicinity of a miner. These results show that donning PAPRs can lower the miners’ exposure to respirable coal dust in their workplace.

Feb 1, 2025

What is your personal view and assessment of the overall health of the industry in the current global economy? The economic outlook remains soft for the near future and, although the global economy is showing signs of recovery, uncertainty has tempered the pace of recovery. In addition to uncertainty, we are still facing significant economic challenges in many parts of the world, including Europe and the United States. The rapid expansion of China?s economy has recently slowed, further contributing to the sense of uncertainty in the overall health of the global economy. This situation is both a blessing and a curse, depending on which sector of the mining industry we are considering. For example, coal, industrial minerals, aggregates, base metal and precious metals markets are impacted by different forces and drivers and will experience different outcomes within the same economic environment. Let me give a few concrete examples to illustrate this concept. The prevailing economic uncertainty that I have just described tends to drive investors toward safe havens. Gold has historically been viewed as a safe haven and as long as investors shy away from traditional investments, gold prices will remain high and gold mining companies will continue to expand and invest capital in their operations. The same sluggish economy that drives gold prices higher has the opposite effect on other segments of the minerals industry. A great example of this is industrial minerals and aggregates used in construction. The markets that consume these minerals have contracted significantly over the past five years. The outlook for this segment is poor, as the glut of available housing continues to inhibit demand for new construction and, thus, many industrial minerals. In addition to this, the federal government?s lack of political will to enact long-term legislation funding transportation and infrastructure projects continues to be a drag on the U.S. aggregates industry.

Jan 1, 2013

By Wei Victor Liu, Na Zhang, Chengkai Fan, Bei Jiang

The truck haulage data from open-pit mine sites are usually massive and multidimensional with multi-peak Gaussian distributions. Artificial neural networks (ANNs) are well-known machine learning algorithms to handle massive and multidimensional data for building models. Moreover, Gaussian mixture modeling (GMM) is a suitable option for processing the data under multi-peak Gaussian distributions and improving model accuracy. For the first time, this study used a back propagation neural network (BPNN), an extreme learning machine (ELM), and a Bayesian regularized neural network (BRNN) coupled with GMM to deal with the complex truck haulage data and build three weighted ensemble models (WE-BPNN, WE-ELM, and WE-BRNN models) to predict truck productivity at mine sites. Decision tree (DT), random forest (RF), gradient boosting machine (GBM), and extreme gradient boosting (XGBoost) were used to build models to be compared with the weighted ensemble models. The results showed that the WE-BRNN had a higher accuracy than the WE-BPNN and WE-ELM models. The proposed weighted ensemble models performed better than the benchmark models in predicting truck productivity, indicating that a weighted ensemble approach based on the GMM analysis significantly improved the model accuracy. Based on the relative importance analysis, haul distance was the most crucial input variable for predicting truck productivity. This study provides a new approach to predicting truck productivity, which will help mining companies make sound budget decisions and improve mine planning.

Mar 2, 2023

By M. A. Trevits, A. Ozment

"According to the Office of Surface Mining Reclamation and Enforcement Abandoned Mine Land Inventory System, in 2013 there were 98 underground mine fires burning in 9 states. This is considered by experts to be an underestimate for the actual number of fires nationwide. Abandoned mine fires, if left uncontrolled can burn for years and in fact, one of the most well-known mine fires in the US, the mine fire in Centralia, PA, which began in 1962 has been burning for over 55 years. In Centralia, the mine fire won the battle, despite suppression and control efforts, as most of the residents were bought out by the State of Pennsylvania and moved away. However, the world record for the longest-burning coal fire, which may have been started around 6,000 years ago in New South Wales, Australia is still smoldering. Suppressing a coal mine fire requires cooling the hot zones and removing any source of oxygen. If the workings are shallow, the fire zones can be unearthed and the burning rock mass can be quenched on the surface. If the workings are too deep to excavate, then the fire must be fought remotely through boreholes using a variety of agents including water, gas-enhanced foam and grout. Access to surface areas for drilling can be problematic due to topographic and property constraints. When this occurs, large areas of burning may go unaddressed or simply left to burn. Fire Solutions, Inc. has been investigating the use of gas-enhanced foam in concert with directional drilling technology. Gas-enhanced foam has the advantage of using less water and adds inert nitrogen gas to displace oxygen to infiltrate and suppress a fire. Directional drilling has the capability to steer a borehole to a specific place underground. Directional drilling has many advantages over conventional drilling technology as it can provide the least disruption to the ground surface, minimize surface preparation and reclamation costs, multiple sites can be accessed underground from a single site and thus treated simultaneously and it offers increased efficiency because it is not constrained by difficult terrain. This paper discusses the combined use of these two technologies and it is hoped that with the use of these two technologies the efficiency and capability to address mine fires will be significantly improved. INTRODUCTION According to the Office of Surface Mining Reclamation and Enforcement, Abandoned Mine Land Inventory System, in 2013 there were 98 underground mine fires in 9 states. This is considered to be an underestimate for the actual number of fires nationwide. Many mine fires are started by people burning trash where the coal seam or an abandoned coal mine is close to the surface. Other fire ignition sources include lightning and forest fires. Once ignited, a coal mine fire can easily spread into the remaining coal pillars and mine entries. Once established, the fire creates its own ventilation system supporting further combustion by drawing air down into the workings through unsealed mine shafts, fractures and surface subsidence depressions. As the coal left in the workings from the past mining operations burns, the mine void can collapse, causing subsidence and creating dangerous voids, damaging damage overlying surface structures and roadways. The products of combustion include smoke and noxious fumes such as carbon monoxide gas. These products are released to the atmosphere through fractures that develop within the ground surface, killing vegetation and creating serious health hazards [1]."

Jan 1, 2018

By M. Ramokhothoane, S. Rupprecht

"NTRODUCTION Women employment in the mining industry dates back to the 19th century. Various parts of the world, for example, India, Japan, the United Kingdom and the United States of America had women employed in large numbers. The women’s jobs were primarily manual in nature. Women were used to carry coal in buckets from the coal face and out the mine, and those who worked on the surface plants were used to sort waste rock from the coal product. Other heavy industries, which were traditionally male dominated, for example the military, also had a considerable number of women supporting the war effort. The outbreak of war also caused a shortage of labour, which in turn, necessitated that women were used in various roles during the war. After World War II, women returned to their traditional roles, but had acquired new skills, and had a different outlook to life. The wearing of pants and short hair became fashionable, as a result of being in the army.Various laws were passed which prevented the employment of women underground. Different countries had rules that they believed were in the best interest of women and were of the opinion that the rules somehow were protecting women against the harsh working conditions. In South Africa, post 1994, there has been a shift in thinking in regard to the employment of women in the mines. WOMEN IN SOUTH AFRICA MINING In the words of the Minister of Women in the Presidency, Minister Susan Shabangu, “women must take centre [sic] stage as the country gears itself for the implementation of radical socio-economic transformation policies and programmes in the next five years” (SA Government News Agency, 2014). In as much as some progress has been made in advancing women, more needs to be done in order to realize sustainable benefits in the economy. The emancipation of women is a reality and remains top of the South African government agenda. From the Authors’ experience there are two types of men in the mines. The first group support change and see the value in it. To them, women in mining bring in the diversity and play the complementary role in achieving greatness. There is no fear of job security and humiliation but a great sense of “camaraderie”. The other group continues to enforce stereotypes, which works against the spirit of redressing the imbalances of the past."

Jan 1, 2018

By V. Claremboux

The transformation of raw iron ore into high quality steel can take place via several processes. A general consistent theme involves the upgrading of the iron ores via methods such as flotation and magnetic separation, the preparation of an agglomerate such as via pelletization or sintering, the smelting of the agglomerate into a high grade iron product, and the further refining of iron into specific steel alloys. Each of these steps admit potential for optimizations and alternatives, and the process overall is critical to meeting the world’s continuing iron demands.

Feb 1, 2025

By Michael Day, Paul Kos, Scott Brinton

Quantitative hydrogeologic characterization of fractured rock is challenging because fracture systems are convoluted and difficult to characterize discretely. For large-scale water resource impact analyses, it may be more appropriate to use a watershed water balance approach and analyze fractured systems in terms of “bulk” hydraulic parameters over a large enough scale (hundreds of meters), so that the fractured media may be evaluated as “equivalent” porous media [1]. This is a common investigative methodology for mountain watersheds in fractured bedrock terrain because it does not rely on discrete flow paths but instead evaluates inputs to (recharge) and outputs from (discharge) the ground-water system [2,3]. This paper describes the use of this methodology to perform a practical and cost-effective hydrogeologic characterization and mining impact analysis for a proposed granite quarry in a mountain watershed. The key conclusions of the study guided the mine planning that was designed to minimize impacts to the fractured granite hydrogeologic system and preserve recharge to downgradient sedimentary aquifers.

By S. G. Britton

Microcomputer analysis has long been a technique for engineering professionals to improve the theoretical and practical design of continuous mining systems. Such work has been typically composed of modeling observed events and then introducing a variety of known elements with predicted results to compare against the results of the model. Programs written in BASIC, Cobol, Fortran, or other language dominated such efforts. These programs have taken years to develop and prove out. This paper explores a new management tool used at TMC on a daily basis to track and improve continuous mining systems through the use of microcomputers and Lotus 1-2-3 software. By analyzing data provided by section foreman, shift foreman, and maintenance personnel against predetermined goals, new production targets are developed, weaknesses in the current mining systems are identified, and the results of changes are measured. The results of this system on the productive output of TMC systems are on the order of ten percent improvement.

Jan 1, 1991

By L. Wilfley, G. A. Calboreanu

"Wear resistant 25% Cr hard cast iron is a heterogeneous material containing 1,600 HV hard chromium carbides embedded into martensitic matrix. It is the most used cast alloy in wear operations of mining industry, chemical industry, fracking, etc. During the last decade the hard iron manufacturers increased wear resistance in the following ways: • Reduce / eliminate harmful retained austenite and chromium + carbon depleted areas especially within eutectic carbide cells. In Max5A the improved 25% Cr alloy brittle carbide eutectic cells are removed which increases toughness. • Delay delamination between chromium carbides and matrix particularly during sliding abrasion wear. Delamination commences at the weakest chromium carbide – matrix contact lines exposing chromium carbide to localized bending stresses which gradually chip carbides away. Once the chromium carbide base is removed accelerated wear degradation occurs. • Evenly randomize and avoid discontinuities in the chromium carbide network. When chromium carbides are perpendicularly positioned to the wear surface wear rate is minimized. On the contrary the highest wear rate takes place when 3D oriented chromium carbides are parallel with the wear surface. In this case chromium carbides cover top network discontinuities being just matrix supported which leads to rapid carbide cracking. The new hard iron discussed in this paper fulfils and exceeds the above requirements increasing the casting service life around 250% in various wear operations. Physical and mechanical properties of Max5A are compared with well manufactured Industry Standard 25% Cr hard iron. The paper presents practical accomplishments obtained in the USA, South America and India. INTRODUCTION The chemical composition of Max5A and Industry Standard 25% Cr are identical like specified by ASTM A532 Class III Type A requesting C = 2.0-3.3% and Cr = 23.0-30.0%. Manganese, silicon, nickel, molybdenum and copper contents are limited by maximum accepted quantities.[1] According to published data the eutectic chromium carbides chemical composition of 25% Cr hard iron is Cr = 54% and C = 8% which indicates strong depletion of chromium and carbon along chromium carbide - matrix interfaces. [2] The optimized Max5A microstructure has minimized retained austenite, is devoid of harmful carbide eutectic cells and has the most advantageous chromium carbide and secondary chromium carbide morphology. This favorable microstructure increases wear resistance, mechanical properties and corrosion resistance. The paper compares the Max5A microscopic features and mechanical – physical properties with similar properties of high quality Industry Standard 25% Cr."

Jan 1, 2017

By J. R. Evans

In order to patent an industrial mineral placer mining claim, it must incorporate an economic deposit. Each ten acre parcel is evaluated for its mineral -in -character nature. Nonmineral -in -character parcels cannot be patented. Economic concerns include: claim locations, dummy locators, common variety nature, "excess reserves," and environmental constraints. Also, geologic and mineralogic studies, sampling and testing procedures are vital. Mining, milling, processing cost, and taxes must be evaluated. Product marketability analysis is necessary before starting any cash flow or discounted cash flow study. Valid data is essential to evaluate an economic industrial mineral deposit.

Jan 1, 1997

By R. C. Emmett

The industrial practice of concentration of solids and production of clear solution by gravity sedimentation is an old technology. Through the years, many devices have been designed and built to aid this process. One of the more significant developments was a revolving rake mechanism to convey settled material to a central discharge point of a circular tank, patented in 1907(1). In recent years, clarification systems employing parallel inclined plates have appeared on the market; the original device utilizing this principle was patented in 1886(2). Numerous other methods have been invented, tested, discarded and sometimes re-invented, all with the specific intention of improving the capacity of a particular settling area. Sedimentation theory, as expressed in Stokes' Law, shows that the rate of settling of a particle is directly proportional to the difference in density between the particle and the surrounding liquid and, more significantly, proportional to the square of the particle diameter. Anything that can increase the latter will greatly assist sedimentation and, as a result, flocculation always has been an integral part of sedimentation. Most materials suspended in aqueous media are naturally flocculent to some degree and, hence, are readily concentrated by sedimentation, although sometimes very slowly.

Jan 1, 1978

By L. M. Gochioco

The U.S. coal industry is under-going dramatic changes to meet the challenges of the keenly competitive fuels market. The application of innovative technologies is needed to improve safety and to increase productivity in order to make coal more competitive as a fuel. As more coal companies shift into capital intensive longwall mining, there is a clear need to invest more in exploration before mine plans are made. Coal seam anomalies may create adverse mining conditions. The early detection of these anomalies could make the longwall mining safer and more productive through improved planning. A standard exploratory drilling program can provide only limited geologic information. The seismic reflection technique can be used to detect coal seam anomalies and is effective in reconnaissance surveying. Recent advances in the quality of coal seismic data have increased the success rate of seismic surveying. Therefore, surface seismic surveys, coupled with selective drilling, will come to play an integral role in coal exploration in the 1990s.

Jan 1, 1990

The Kinross DeLamar Mine has been operated for more than 17 years producing precious metals dore' from ores, principally silver bearing with associated gold co-products. In late 1995 a new orebody was commissioned, the Stone Cabin orebody, and the site began a phased shift from silver dominance to gold dominance in terms of precious metals revenue. The Knelson Concentrator was selected to remove gold from a portion of the cyclone underflow stream in the grinding circuit. This paper describes the development of the flow sheet, specific mineralogical impacts on Knelson product and downstream materials, and impacts on mine/mill grade reconciliation.

Jan 1, 1997

By R. J. Sheets

"INTRODUCTION What is the primary responsibility for geo-engineers in mining? Early in my career, I was asked this question by an experienced engineer. After explaining some various tasks, I was informed that the main responsibility was to monitor. Although this proved true for many cases, I came to understand that monitoring is merely one means to achieve the primary responsibility of a geo-engineer – ensure the safety of all personnel. The potential for groundwater to impact stability allows this responsibility to be shared with hydrogeologists as well. Inherently, we monitor to identify risks; we analyze designs and develop models to mitigate risks; and we are provided opportunities to explain to supervisors the geo-risks to personnel and mine plans that will result from particular courses of action. A couple years ago, I took an opportunity to share experiences from the first several years of my career as a geotechnical engineer with junior geo-engineering staff within my company. The intent was to share situations that were a part of my development, so they could learn and understand their responsibility to the safety of all personnel. Similarly, the purpose of this paper will be to share these thoughts with new geo-engineers in the industry in order to help prepare them for the challenges they will face. WHAT IS OUR PURPOSE? A senior hydrogeologist shared an experience that occurred in their career. The experienced hydrogeologist had spent some time with the hydrogeology staff, most of them relatively new to the mining industry, to understand how they viewed, and carried out, what they perceived as their responsibility at an active mining operation. After a couple months of observing and mentoring, the senior hydrogeologist met with everyone and posed the question above. I am sure that most junior geo-engineers would start explaining different tasks or projects that they must complete. The list would include monitor groundwater levels, track slope movement, evaluate designs, build models, oversee drilling programs, etc. These individuals did as well their supervisor. After going around the room allowing each individual to answer, the experienced hydrogeologist provided them the real answer to the question: SAFETY. If you examine the root intent of nearly every responsibility geotechnical engineers and hydrogeologists have, it is to apply our professional skills to ensure the safety of our workforce. When the objective of safety from the geotechnical and hydrogeology disciplines is achieved, inherently accomplishing the mine plan should follow suit, or it should significantly minimize the impact by gravity or groundwater. The objective of a hydrogeologist is to ensure the soil or rock around an open pit or underground mine is dewatered; this specific objective will reduce pore pressures which could lead to a possible ground failure. They ensure a working bench/UG level is dry, so operations are not dealing with adverse conditions while mining. A geotechnical engineer is expected to use all available information and engineering judgement to provide design recommendations, so that the mine will not catastrophically fail. Additionally, they will implement the monitoring systems to identify hazards in advance in the event that the design is flawed and people need to be evacuated. We all know that safety is important to everyone; however, our particular set of technical skills play a significant role in ensuring the safety of a large portion of the global mining workforce."

Jan 1, 2018

By Julian W. Feiss

Before undertaking to present to you a current analysis of copper, I would like to preface my remarks with a few observations that in themselves have a bearing upon commodity reviews in general. Having sat through a large number of such reviews since first joining the A. I. M. E. nearly forty years ago, I have no illusions about the hazards of the undertaking. If a speaker presents a statistical summary of commodity economics for the last year, most of his audience, having already read at least four commodity summaries on the identical subject, either get up and walk out or fall asleep. Should the latter happen, and were the listener to tumble from his chair and break his neck, obviously the speaker is liable. The subject matter seldom lends itself to histrionics on the part of the speaker so dangers of heart attack in the audience are not too great. Therefore the speaker, in order to retain listener interest, resorts to prophecy. Such venture was undertaken long ago by weather soothsayers, the "harouspex" of Ancient Rome, who generally cut up a sacrificial sheep and after staring at the entrails made their predictions which I understand had a batting average somewhat better than those undertaken on Wall Street based upon Dow Jones averages. Not being a licensed harouspex I cannot undertake predictions. I shall, however, fall back upon the experts.

Jan 1, 1965

By Ritika Kundu, Moussa Wone, Amanda M. Morgan, Tatiana K. Proctor

The Piney Branch CSO 049 Storage Tunnel (PBST) will be the last major project for the DC Clean Rivers Program. The project includes construction of a 2,200-foot-long, 18-foot-internal-diameter storage tunnel; two connections to combined sewer infrastructure; and two shafts. Major challenges include excavation underneath an existing live outfall that must remain in service; excavation of the tunnel through several areas of low rock cover and mixed-face conditions; and negotiations with a variety of federal, regional, and local stakeholders to address project impacts. This paper describes the overall project scope; geotechnical conditions along the alignment; design and construction challenges; and construction procurement.

Jun 23, 2024

By L. Patts, J. Hummer

The use of diesel-powered equipment in underground coal mines has increased substantially during the last ten years in an effort to enhance mine safety and productivity. Pennsylvania and West Virginia are two of a number of states with regulations governing the use of such equipment. These states both developed and promulgated regulations before permitting diesel equipment in their underground coal mines because of concern for miners’ safety and health, especially with regard to the contamination of mine ventilation air with diesel exhaust emissions. The major components of diesel exhaust emissions are combustion gases and diesel particulate matter. The gaseous emissions consist of carbon monoxide, carbon dioxide, oxides of nitrogen, sulfur oxides and unburned hydrocarbons. The diesel particulate matter (DPM) is comprised of solid carbon particles, liquid and solid hydrocarbons, sulfates and moisture. The Federal Mine Safety and Health Administration (MSHA) also promulgated regulations in an effort to control diesel emissions in underground coal mines. MSHA has adopted threshold limit values (TLVs) for all gaseous components of diesel exhaust, which were established by the American Conference of Governmental Industrial Hygienists (ACGIH). MSHA (30 CFR Part 72 Subpart D) has established a tailpipe DPM emissions limit of 2.5 g/hr for diesel engines used in permissible equipment, heavy-duty non-permissible equipment, generators and compressors used in underground coal mines. A tailpipe DPM limit of 5.0 g/hr has been established for light-duty outby diesel-powered equipment. The rationale for the tailpipe emissions limit was that an ambient measurement of DPM in a coal mine was not feasible because there is no established sampling method able to distinguish between coal mine dust and DPM. The stringent tailpipe emissions limit mandates the use of exhaust aftertreatment devices for most diesel engines used in underground coal mines today. One method by which tailpipe DPM can be reduced to MSHA limits involves using an exhaust cooling device in conjunction with a high-temperature, disposable diesel particulate filter.

Jan 1, 2011

By T. Tempel

In 1994 Newmont Gold Company commissioned a 2.5 Mt/a refractory gold ore roasting plant near Carlin Nevada. Many unique characteristics of this facility required use of specialized materials of construction in the areas of dry grinding, roasting, gas cleaning, and sulfuric acid production. Process conditions and design criteria that necessitated the use of special materials include; siliceous and abrasive ore, low roasting temperatures, gas streams with high concentrations of oxygen and sulfur, and stringent environmental regulations. Materials selected for use were ceramics, corrosion resistant steels, high temperature steels, and high temperature polymers, lead, polypropylene and low flammability PVC.

Jan 1, 1997