Search Documents

By H. Huang, Y. Takasaki, R. N. Gow

"The presence of enargite (Cu3AsS4) is problematic in gold processing not only because it is environmentally hazardous due to its arsenic content but also because it is refractory, causing both cyanide and oxygen consumption to increase. Selective leaching and treatment of the arsenic would prove advantageous prior to applying conventional gold leaching methods. The reactivity of enargite samples from Butte in Montana and Quiruvilca in Peru were spectroelectrochemically studied under alkaline conditions – pH range of 8-13 – using Raman spectroscopy and cyclic voltammetry. Raman spectra of the surface were collected during and after potentially cycled voltammograms in order to determine and compare surface species against theoretical EH-pH diagrams constructed from mass-balanced thermodynamic calculations using STABCAL software. Under slightly oxidizing conditions, covellite (CuS) peaks were found in a short matter of time, above ~100mV vs. SHE for pH 9-13, suggesting arsenic leaching specifically occurred. At longer conditioning times, elemental sulfur was observed and tended to passivate the surface. The presence of elemental sulfur suggests that copper was eventually leached from the surface. By operating above pH 12, under slightly reducing conditions near -300mV vs. SHE, arsenic can be selectively leached as thioarsenate (AsS4 3-) or thiosulfate (AsO4 3-) without sulfur formation.IntroductionEnvironmental limitations on the pyrometallurgical processing of ores and concentrates bearing arsenic and other hazardous elements often outweigh those in hydrometallurgical processing, particularly when minerals like enargite (Cu3AsS4) are present. The hydrometallurgical processing of enargite-bearing materials can be broken down into two categories: the co-dissolution of arsenic and copper under acidic conditions, and the selective leaching of arsenic under alkaline conditions. The selective leaching of arsenic would preferably leave behind copperrich sulfide phases, typically chalcocite (Cu2S) and covellite (CuS), which then become more amenable to conventional copper (and gold) processing. Furthermore, selective leaching often employs sulfide (S2-), bisulfide (HS-) or polysulfides (Sx 2-) to first extract the arsenic as AsS4 3- and AsS3 3- (Delfini et al., 2003; Anderson and Twidwell, 2008; Tongamp et al., 2010a,b). However, hypochlorite leaching (Viñals et al., 2003; Curreli et al., 2005; Mihajlovic et al., 2007), ammoniacal leaching (Gajam and Raghavan, 1983), and finegrinding to mechanically activate the enargite surface (Balaz and Achimovicova, 2006) have been investigated to increase the normally slow reaction kinetics. Because gold ores are becoming more refractory due to increasing arsenic contents as a result of enargite, these methods are being examined more closely by the gold-mining industry."

Jan 1, 2015

By L. Zhou, D. Bahrami

Mine ventilation is one of the most important aspects of mining operations in underground mines. It is critical to maintain and deliver required fresh air to the active areas to reduce the risk of overexposure to hazardous contaminants or explosive atmospheres. An unexpected or unknown event such as roof collapse, unexpected mine door closure/opening, a fire/explosion, or fan malfunction could adversely alter the airflow distribution within the mine ventilation network that could lead to a hazardous underground environment. Knowing the occurrence and location of such an incident is of critical importance. In this study, the authors developed a novel methodology to assist mine operators in quickly identifying the location of any abnormal airflow change within the network using the airflow changes at monitored airways. The concept is based on a direct derivative method developed by the authors. This paper provides the details of the developed method as well as numerical verification examples. The application of this method can benefit mine operators and safety personnel in making better decisions during a mine emergency response operation to mitigate hazardous conditions arising from an unexpected airflow disturbance

Mar 2, 2022

By J. Jorge, J. Mariño-Salguero, B. Álvarez-Rodriguez, J. M. Menéndez-Aguado, J. J. de Felipe

"This work focuses on the characterization of heat generation during dry fracture by direct impact of a tantalum ore. Moreover, an attempt was made to quantify the heat energy loss to the environment during the grinding process of a ball mill. The study was carried out using mineral samples from a Spanish mine that were characterized by measuring their density and specific heat. During the experiments, increases of temperature ranging from 5.9 to 7.3 °C after the fracturing process were observed. A numerical model was then applied to calculate temperature distributions through the mill wall. Three possible combinations of heat transfer coefficients were analyzed, from (1) Kapakyulu and Moys, (2) Duda and (3) the heat transfer laboratory of Universitat Politècnica de Catalunya. The models with the coefficients from Kapakyulu and Moys and the heat transfer laboratory of Universitat Politècnica de Catalunya were found to provide results that were in best agreement with the experimental data. IntroductionEvery year, several billion tons of metallic ores, minerals, cement and other solids used in the ceramic and chemical industries are subjected to size reduction in ball mills around the world. The U.S. Department of Energy (2005) reported that in the United States about 29 percent of the total energy used by the mining industry, or 0.4 percent of total U.S. energy consumption, is used in comminution. In Canada and Australia, comminution is responsible for about 2 percent and 1.5 percent of total energy use, respectively. In nonindustrialized countries where mining constitutes higher fractions of their industrial sectors, comminution costs represent a significant contribution to mine operating costs. The specific energy consumption values for the grinding of these materials typically range from 5 to 50 kWh/t. Thus, a significant amount of electrical energy is consumed in the ball mill grinding operation (Aguado et al., 2006; Gupta and Sharma, 2014). Grinding can represent up to 50 percent of the direct operating cost in a mineral processing plant, especially as comminution devices operate in highly inefficient ranges of 4 to 8 percent (Wang, Yang and Yu, 2012)."

Jan 1, 2017

By Tamás Megyeri, Dániel Borbély, Vera Szánto, László Kovács

"Upon completion, the Bátaapáti deep underground radioactive waste repository complex (National Radioactive Waste Repository - NRWR) will provide safe final disposal for low and medium-level radioactive waste from the Paks Nuclear Power Plant in Hungary. The waste emplacement is in progress and one of the main concerns related to the development is ensuring a feasible plan is in place for permanent repository closure. Detailed hydrogeological observations and safety assessments revealed that the clay filled fault zones penetrated with the access tunnels play determinant role in the long-term confinement performance of NRWR, so they need to be plugged. Detailed mechanical analysis and numerical modelling of the tunnel constructed through a fault zone is presented here to gain a better understanding of the rock mass and rock support behavior. The effect of stress reflection is demonstrated and its consequences are described in detail. A recommendation is given for tunnel support design in such conditions. INTRODUCTION Crossing fault zones is a challenging task during tunnel construction and can lead to failure if not properly accounted for during design and construction. These failures are can be caused by high water inflow or stability loss of the rock mass surrounding of the tunnel (examples can be found in CEDD, 2015). The prediction of the magnitude and development of displacement has a considerable impact on issues during tunnel construction. Changes of rock mass stiffness or structure ahead of the face, to a great extent influencing stresses in the vicinity of the tunnel and thus deformations (Steindorfer, 1998). Further research with numerical simulations was carried out, and the qualitative and quantitative evaluation of displacement vector is presented in (Grossauer et al, 2005). The concern associated with crossing fault zones was considered during the design of the Bátaapáti deep underground radioactive waste repository complex (NRWR) in Hungary. In the case of NRWR project, the fault zones have an impact on maintaining the stability of the surrounding rock mass as well as the final sealing of the repository. As part of the final closure design, a complex numerical modelling program was completed to gain a better understanding of the mechanical behavior of the rock mass and the monitoring observations during construction. Even though the need for the presented study is closely related to the NRWR project, the results can be used in any project related to fault zone crossing. The methodology used to better understand the impact of crossing fault zones for the NRWR project is presented in this paper. First the project background is introduced including an overview of the underground facilities, the aim of the repository, and the construction experience gained from the first crossings of the fault zones. After that the in-situ and laboratory testing is summarized. The numerical modelling methodology is detailed in the next section. Not only the outcome of the model is presented, but the results are compared with the experience and observations made on site. Since a good agreement is found between the actual and the modelled behavior, the conclusions are based on the validated result. To fulfill the aim of the paper, the stress reflection concept is introduced to explain the mechanical behavior of the fault zone and the rock support; furthermore straightforward suggestions are made for rock support design."

Jan 1, 2016

By E. H. Smith

St. Joe Minerals Corp., a subsidiary of Fluor Corp., treats high-grade gold, silver, and copper ore at its El Indio plant at an altitude of 4 km in the Chilean Andes. The ore is complex, being a mixture of massive pyrite-enargite and quartz, both containing very fine gold and silver. Treatment produces a copper flotation concentrate containing high levels of gold, silver, and arsenic, and also dore bullion. Part of the flotation concentrate is roasted to remove the arsenic content, and arsenic trioxide is collected as a by-product.

Jan 1, 1987

By Thomas C. Shapiro

Introduction In recent years - even months - the number of articles on computers has increased rapidly. One can hardly pick up a newspaper or magazine without seeing a computer-related article. The article usually explains how the computer will change our lives. Many of us have some concern about the nature and type of change. For most of us, though, the problem is lack of information and understanding about how computers work. In other words, how do we make cost-effective decisions about computers? This three-part series will explain, simply, what a microcomputer is, how it works, and how to decide if you need one. This first article will define terms and briefly discuss areas where computerization might be economic. The second article will discuss geology and mining applications. The third article will discuss plant, administrative, and geotechnical areas as well as the future of software development in the minerals industry. Terms and Concepts All computers have input and output devices and a central processing unit (CPU). Information - instructions and data - is communicated to the computer by means of input devices. These instructions to the computer are converted into language that the computer understands. This causes the instructions to be carried out in the CPU. The result of these operations is translated back into language that we understand. This information is then sent to output devices such as printers and video display tubes. Traditionally, peripherals were devices separate from the main-frame (the CPU and memory) and were used to input, output, and store information or instructions. Today, peripherals perform the same functions though they may be housed in the same cabinet as the CPU and memory. Historically, peripherals included all input and output devices not part of the mainframe. Input devices include keyboards, magnetic tape, and card readers. Tapes and disks are input as well as output devices. Output devices are printers, CRTs (Cathode Ray Tubes), and any mass storage device capable of storing data when directed to do so by the computer or the program. In fact, any mass storage device that can give the computer data when requested is an input device. Mass storage devices include floppy disks (thin, round sheets of plastic covered by metal particles), and hard disks. The latter are thicker and more densely coated with metal particles. This allows much more information to be stored. Another type of mass storage is magnetic tape. Its type and size varies widely. Processing and Storage Any computer understanding must include how instructions and data are processed and stored. Information is stored as a positive or a negative field known as a "bit." There are eight bits in a byte. The bits can be represented as either a one or a zero. Thus the code for a byte representing the numeral one is 00110001. The byte representing the letter A is 01000001. These codes are from the American Standard Code for Information Interchange (ASCII). ASCII defines the standard set of characters including alpha, numeric, and special characters. The computer's memory has allocated locations where instructions as well as incoming information can be stored. All information and instructions are stored as binary numbers bit by bit - zeros and ones. The amount of data that can be stored is referred to as either thousands or millions of bits or bytes. The letter "K" is used to designate one thousand units. The letter "M" is used to mean one millon units (one meg). Disks Thus, a 113-mm (5 1/4-in.) floppy disk - double sided and double density (DSDD) - contains 320,000 bytes (characters) or 320K. This is about 164 double-spaced, type-

Jan 2, 1984

By E. J. Mayhew

Bentonite and newly discovered deposits of sepiolite, saponite, and hectorite are now being processed and marketed from the Amargosa Valley of Nevada. All of these deposits are large. The bentonite has been known for decades and is the whitest known. The only other sepiolite deposit is in Spain. The only other commercial hectorite deposit is at Hector, California. No other saponite deposit is known. All the components except bentonite are hydrous magnesium silicates. The bentonite is mixed layer Na-Ca. All the materials have characteristics unique to their locale and type, such as high yield point for drilling muds and liquid suspending agents. The sepiolite has geothermal stability. Figure 1.

Jan 1, 1979

By S. E. Phillipson

The Late Miocene San Cristobal Ag-Zn-Pb deposit represents syngenetic and epigenetic mineralization with low- and high-sulfidation characteristics. Geology is characterized by barren dacitic ring fracture domes, mineralized resurgent rhyodacite domes, strongly altered and mineralized tuffaceous lacustrine sedimentary rocks, and an extensive crystal-lithic tuff debris apron. The ore body is hosted by intra-cauldron sedimentary rocks and breccias. Fluid inclusions suggest that silver, lead, and zinc were transported as chloride complexes and precipitated by cooling in veins from <5 wt. % NaCl eq. fluids at 170°-215° C. Silver associated with resurgent rhyodacite was transported as a chloride complex and precipitated by increased H2S activity or increased fluid pH.

Jan 1, 2001

By Thomas R. Hightower

The Thunderbird plant was erected in Sullivan County in Indiana during 1958-1959. It was first put in operation in March of 1959. At the present time the source of the raw coal is from the Indiana No. 6 seam. The underground operation at present consists of two continuous mining units and two conventional units. The underground is all belt haulage and the first unit with which this paper is concerned is the slope belt. It is a 48-inch-wide inclined belt with 980-foot centers and a lift of 275 feet. The belt is powered with a 350 H, P, motor and has a rated capacity of 600 Tons per Hour. The belt is equipped with a Merrick Scale Company Weightometer, The raw coal moves from the belt to a 6&apos;x12&apos; extra heavy Allis-Chalmers Ripl-Flo equipped with 6" round-hole screens. The over product of the screen is fed into a 10&apos;x20&apos; long McNally- Pittsburg rotary breaker equipped with 4-l/2" round-hole screens. The oversize rock is discharged into a bin that is emptied with a refuse truck. The through-product of the breaker, along with the through-product of the Ripl-Flo, passes either directly to the McNally Giant washbox or to a 36" belt that transports it to a 1000-ton storage bin,&apos; The change from either to the washbox or to the storage bin is made by use of a motorized gate controlled by the plant operator,

Jan 1, 1961

By Richard J. Waxweiler, Frank E. Lundin, Robert J. Roscoe, Victor E. Archer, Michael J. Thun, Joseph K. Wagoner

[Introduction] Since excess lung cancer mortality was first noted in the late 1800&apos;s among Joachimsthal-Schneeberg miners, there have been a number of studies of the long term health effects among various types of miners exposed to elevated levels of radon and its radioactive decay daughters. Substantial excesses of lung cancer have been noted among miners in the Joachimsthal mines (Sevc, 1976) , lead-zinc miners in Sweden (Axelson, 1979) , fluorspar miners in Canada (DeVilliers, 1971) , iron miners in Sweden (Renard, 1974) , uranium miners in Canada (Hewitt, 1976), and metal (Wagoner, 1963) and uranium miners in the United States (Lundin, 1971; Archer, 1976). The latter prospective cohort has also been shown to be at an excess risk of death due to tuberculosis, nonmalignant respiratory disease, and accidents when followed through September 30, 1974 (Archer, 1976). This report extends the followup of this cohort of miners through December 31, 1977 and expands the mortality analysis to investigate more cause-specific categories. [Methods] During the decade beginning with July, 1950, medical teams from the United States Public Health Service (USPHS) examined 3362 white and approximately 780 nonwhite males who had worked underground in uranium mines in the Colorado Plateau at least one month by January 1, 1964. Occupational, medical, and smoking histories were obtained during the examinations and often updated/confirmed during subsequent annual censuses of the miners conducted by the USPHS. The white miners now have been followed-up through December 31, 1977 using the Social Security Administration, Internal Revenue Service, direct telephoning and various other sources. Death certificates were obtained for the deceased and coded directly into the Seventh Revision of the International Classification of Diseases, Adapted, using the rules in effect at the time of death. Deceased miners for whom no certificate has yet been located were assumed dead on the date specified by the reporting agency, cause of death unknown. The uranium miners cohort was analyzed using a modified life-table system developed by the National Institute for Occupational Safety and Health (NIOSH). Person-years at risk of dying (PYAR) were calculated for each miner from his first USPHS medical examination date or date upon completion of one month of underground uranium mining if that was later. PYAR were calculated specific for five-year age groups, calendar periods, and periods after first underground uranium mining. The numbers of cause-specific observed deaths among the cohort occurring by December 31, 1977 were compared to the numbers of expected deaths. The expected deaths were calculated by multiplying the appropriate PYAR by the United States death rates for white males specific for five-year age groups, five-year calendar periods, and cause. The results were summed over the age and calendar period specific categories to obtain the total expected deaths for each cause. Standardized Mortality Ratios (SMR&apos;s) were calculated for each cause by dividing the observed number of deaths by the expected number of deaths and multiplying by 100. In some tables, two-sided 95% confidence intervals for the SMR&apos;s were computed using either Fisher exact confidence limits, if the observed frequency was less than eight, or approximate confidence limits, if the observed frequency was eight or greater, to indicate statistical significance. Because a priori hypotheses had been well established, one-sided lower confidence limits were used for tuberculosis, lung cancer, other nonmalignant respiratory disease (ONMRD), accidents, and total mortality. [Results] The cohort included 589 miners first examined in either 1950, 1951 or 1953; 753 first examined in 1954; 1235 first examined in 1957; 5 first examined in 1958; and 782 first examined in 1960. In Figure 1 the distribution of the cohort by first year of underground uranium mining indicates that 13.7% started before 1947 and would have thus had an opportunity to be followed beyond 30 years

Jan 1, 1981

By Gordon O. Prickett

In two case studies we look at strategies of acceptance that the analyst can employ to gain entrance and to see his problem solution out to use. The first example comes from metal mines. The problem area was excessive usage and cost of wear parts in the concentrator and an atmosphere of crisis over frequent and unexpected breakdowns. The second case pertains to coal exploration. Better methods were being sought for representing coal quality in developing reserve tonnages. The first strategy is - Develop a detailed Human Impact Statement. The second strategy is - Write down in plain language with the keeper of the problem what he will consider as success in dealing with his problem.

Jan 1, 1978

By D J. Bradshaw

It is well known that the chemical environment determines the success of the flotation process, however its characterization and control is difficult to achieve. This work evaluates the use of various measurements, including mineral potential measurements, in gaining an understanding of the influence of varying parameters such as the milling media and the reagent suite composition on the flotation performance of a platinum group metal (PGM) bearing ore. The results showed differences in the response of the various mineral electrodes to the different conditions, however the changes in flotation performance of the different minerals in the ore could not be wholly described by the electrochemical changes, demonstrating the limitations of these measurements.

Jan 1, 1999

By Jim Buckley, Ryan Sibley, Scott G. Giltner, Thomas Pallua, Joe Schrank, Robert Cidlik

Because of variation in rock type and site conditions, it is important to create site-specific prediction models for peak particle velocity (PPV) and understand instrumentation mounting locations to better interpret the readings provided following blasting operations. The Atlanta Airport is expanding the section of underground tunnels for its Plane Train people mover, and drill and blast operations were determined to be the suitable method of excavation for the project. Extensive work was done to begin creating prediction models and determining levels of concern based on readings from various types of instrumentation. This paper analyzes the effect of close quarters construction blast vibrations and observed frequency spectrum on existing structures with data from 22 different seismographs mounted in various locations and ground conditions.

Dec 1, 2022

By Herry Poernomo, Agus Prasetya, Iga Trisnawati, Himawan Tri Bayu Murti Petrus, Gyan Prameswara, Panut Mulyono

We studied yttrium extraction from untreated zircon sand processing waste tailings. Xenotime mineral as the rare earth element source with an abundance of yttrium (REY) was detected in sufficient grade for extraction. As much as 9.03% yttrium exists in zircon tailings (analysed by X-ray fluorescence spectrometry). The presence of yttrium was confirmed by X-ray diffractometry in xenotime minerals, which are yttrium carriers (Y-PO4). The purpose of this research was to determine the effect of leaching conditions on yttrium recovery from zircon sand after alkaline fusion treatment. Alkaline fusion was chosen to decompose phosphate into hydroxide in the xenotimemineral,which will reduce further required hydrometallurgical processing.Alkaline fusionwas carried out for 3 h at 450 °C, with a ratio of sodium hydroxide to zircon tailings sand of ~ 1:1. The alkaline fusion product was leached with water, followed by hydrochloric acid treatment to leach the yttrium. Yttrium recovery reached 87% under optimum conditions (60 °C, 1MHCl, and solid-to-liquid ratio = 1/10 for 7.5 min). A suitable model for yttrium dissolution with hydrochloric acid was diffusion through a solid particle ash layer. The calculated activation energy (EA) for this model was 20.21 kJ/mol.

May 26, 2020

By Charles H. Ricker

Simulation models have been widely used to analyze the operations and characteristics of a variety of systems. Such models mimmick a projected reality by analyzing the interaction of the events, transactions, and facilities which combine to make up the system. The models are structured as a computer representation of the system components and their logical, precedence and timing relationships. The operation of the system is then simulated over some finite time interval to gather analytical and staistical data. This paper presents a method whereby bulk handling systems, either actual or proposed, may be analyzed by means of simulation models to project the enconomic consequences which may be expected from the system over some future time interval. An example is given to illustrate the construction of bulk handling simulation models, the derivation of performance data, and the analysis of the information with an eye to effective decision making.

Jan 1, 1974

By S. M. Moore

Each year more than 400 coal miners are injured (fatal and non-fatal) by rock falling from between or around roof supports. Many of these injuries could be prevented by the installation of roof screen (wire mesh). However, many coal mines may be reluctant to use roof screen because of the added cost. The goal of this study was to determine the potential saving in workers? compensation (WC) premiums that could be achieved due to a reduction in rock fall injuries after roof screening. The WC rate-setting methods utilized by IL and KY were investigated in this study. Using actual data obtained from MSHA, national and state WC bodies and individual insurance companies (e.g. average cost per injury, loss cost rate, number of injuries per year, number of injuries preventable each year with roof screening), hypothetical mines (representing two mine sizes: 67 and 150 employees) were constructed with realistic ranges for estimates of injuries and WC premium costs. Using each state?s actual WC rate-setting formulas, total savings in WC costs after a three-year period were determined. Across both states, savings in WC premiums ranged from 1.8% to 14.6% when injuries were reduced by 10% to 20%. Additionally, an economic analysis was performed for an existing mine consisting of 67 employees. For this mine, the annual cost of a roof screening program was estimated at $240,000. If the screening prevented 13 ?struck by? WC claims over a 3-year period at this mine, the reduction in WC premiums alone could pay for the entire screening program.

Jan 1, 2010

"A carefully planned laboratory test program is the foundation for the successful development of a sulfide flotation process. In this paper, the development of a copper-molybdenum flotation process is described. However, the concepts discussed can be applied to most sulfide flotation systems and to many industrial minerals projects as well. Each step is examined, beginning with sample procurement and covering sample preparation, flotation test preparation grinding, scoping flotation tests for reagent scheme selection, rougher flotation parameter evaluation and cleaner circuit evaluation, through to locked-cycle testing and pilot plant design and operation. Ore variability and modeling to determine the response of various ore types to the optimum conditions established is also examined.IntroductionA carefully planned laboratory test program is essential for the successful development of any sulfide flotation process. These programs usually begin with a series of batch tests on several ore type composites to evaluate appropriate reagent schemes and delineate optimum rougher flotation conditions, such as primary grind size, flotation pulp density, flotation pulp pH and retention time. Cleaner parameters such as regrind size requirements, cleaner pH, pulp density and number of stages are then defined. Semicontinuous locked-cycle tests are performed using the parameters established in the batch tests to determine the effect of middling streams recirculation on flotation performance. The data generated and the experience gained in the locked-cycle tests may be used to design and operate a continuous pilot plant if relatively large amounts of concentrate are required for further process development, such as optimization of byproduct molybdenum production from bulk copper-molybdenum concentrate.A comprehensive ore variability program is undertaken to determine the response of various ore types to the optimum conditions established. These ore variability programs often test hundreds of samples in standardized batch rougher and cleaner tests to ensure that the orebody is well understood.This article describes the development of a copper-molybdenum flotation process, but the concepts discussed can be applied to most sulfide flotation systems and many industrial minerals projects. The block flow diagram in Fig. 1 provides an overview of the development process."

Jan 1, 2016

By Tsunenori Shibata, Kazunori Jimbo, Kaoru Toya, Masafumi Matsumoto, Jinya Mitsui, Toshinori Tsuji

"The Toyama Line is under construction as a natural gas pipeline with a length of 102 km from Itoigawa City to Toyama City. A 2 km-long tunnel section of the pipeline that we are reporting here is being excavated in a mountain area away from an urban area. The geology under which the tunnel is constructed is collapsible fractured breccia slate and Holocene sandy soil. Other tunnels of the Hokuriku Expressway and Hokuriku Shinkansen are in service above the tunnel route. From the starting shaft on Toyama side, conventional tunneling was adopted to facilitate excavating the base rock layer and maintain enough distance from the Hokuriku Expressway tunnel. From the starting shaft on the Itoigawa side, TBM tunneling was adopted to cope with the unconsolidated soft ground for a 200 m-long section from the shaft. We will discuss the issues and countermeasures concerning the selection of a tunnel route and excavation methods, performance of both conventional and TBM tunneling, and underground connecting of these tunnels excavated by conventional (NATM) and TBM methods under a high groundwater pressure up to 1.2 MPa. INTRODUCTION AND BACKGROUND The International Petroleum Exploration Teiseki Co., Ltd. (INPEX) is constructing a high-pressure main pipeline network in the Toyama Prefecture area to promote the use and reliable supply of natural gas as shown in Figure 1. As part of the Toyama line project that has a total length of 102 km, A-1 construction, the nearest section to the tunneling starting point in Itoigawa City, where various tunnel excavation methods have been adopted to install the high-pressure pipeline 20 inches in diameter, a 2 km tunnel in the A-1 construction section discussed here is to be excavated by conventional and TBM methods in a mountain area. Based on environmental studies such as traffic jams due to frequent traffic of heavy vehicles disposing of soil, and the effects of dust, noise and vibration during construction, we selected the route to install the gas pipeline in a mountain area as shown in Figure 2, where the impact on the surrounding environment could be minimized."

Jan 1, 2016

By John Rushton

Surface mining, from ore extraction to processing, requires many types of equipment to obtain the final product. Mine equipment often includes shovels, drills and haul trucks. Ore processing equipment, including plants, mills and concentrators, are also part of surface mining operations. Surface mining operations emphasize production. Production is where the bills are paid and fortunes are made. However, there must be support to keep the equipment operational. To most production people, equipment maintenance is a necessary evil. Maintenance is not glamorous work. It is often neglected when praise is being passed around. It is easy to recognize higher production, greater capacities, faster cycle times or more loads hauled. But who cares if an engine is replaced in 12 hours instead of 48? The answer is, everyone should - from the hourly miner to the mine manager. Surface mining equipment needs constant maintenance work. It must be lubricated, components replaced, electrical problems repaired and other problems addressed. Repair work for any surface equipment takes time away from production. It costs money. Maintenance costs cannot be avoided. However, they can be minimized. Minewide communication should include operations cooperating with maintenance. Traditionally, operations resist surrendering equipment to maintenance if it can continue to produce. The rationale is, every load that can be hauled today is money in the bank. If the unit is taken down, the money is lost. This thinking is prevalent in many surface mining areas, including the mill. "Not on my shift," the operator thinks. "Let the next crew worry about it. The problem with this thinking is in probability and statistics. The longer equipment goes without maintenance work, the higher the probability of equipment failure. When the failure does occur, it is certain to cause the equipment to remain down longer than if the maintenance department had been allowed to take it down. Many mining operations have closed early in their lives because of poor maintenance practices. This has become the industry standard because substandard levels of performance are acceptable. Management believes it gets five to six hours of work from maintenance people during an eight-hour shift. Actually, the industry average is less than two hours of work per shift. Real productivity levels of less than one hour are not unusual. There are few exceptions. However, a daily work schedule (DWS) will increase productivity at many properties by 50% to 100%. A 200% improvement is not unusual. The DWS will work. Maintenance people are among the most intelligent and motivated people on the property. They deserve the chance to be productive. [ ] In preparing a DWS, management needs to understand two productivity principles - the productivity spread and the real maintenance workday.

Jan 1, 1997

By Robert J. Russell

The importance of grinding as a unit operation in all industry has caused much effort to be expended toward improving the facility with which grinding can be done. Endeavor has continued nearly 100 years to formulate laws governing crushing and grinding. This has not been without controversy. However, grinding is an experimental science and our useful knowledge originates in experience. The recorded experience is grinding history. Today, many types of size reduction equipment, each with variations, are available to industry. Frequently, more than one type of grinding equipment will meet a requirement of grinding. However, an economic evaluation of installation and operating costs generally indicates a preferred type. The selection of grinding equipment requires&apos; a consideration of the purpose in grinding, the characteristics of the material to be ground, equipment available for grinding, and the manner in which it can be applied best.

Jan 1, 1960