Search Documents

By G. Frey, D. Scott, C. Pritchard

Controlled recirculation has been used in the metal/nonmetal mining industry for energy savings when heating and cooling air, in undersea mining and for increasing airflow to mining areas. For safe and effective use of controlled district recirculation, adequate airflow to dilute contaminants must exist prior to implementation, ventilation circuit parameters must be accurately quantified, ventilation network modeling must be up to date, emergency planning scenarios must be performed and effective monitoring and control systems must be installed and used. Safety and health issues that must be considered and may be improved through the use of controlled district recirculation include blasting fumes, dust, diesel emissions, radon and contaminants from mine fires. Controlled recirculation methods are expected to become more widely used as mines reach greater working depths, requiring that these health and safety issues be well understood. The U.S. National Institute for Occupational Safety and Health (NIOSH) conducted two controlled recirculation tests over three days at a Wyoming trona mine, utilizing an inline booster fan to improve airflow to a remote and difficult-to-ventilate development section. Test results were used to determine the effect that recirculation had on air qualities and quantities measured in that section and in other adjacent areas. Pre-test conditions, including ventilation quantities and pressures, were modeled using VnetPC. During each test, ventilation quantities and pressures were measured, as well as levels of total dust. Sulfur hexafluoride (SF6) tracer gas was used to simulate a mine contaminant to monitor recirculation wave cycles. Results showed good correlation between the model results and measured values for airflows, pressure differentials, tracer gas arrival times, mine gasses and dust levels.

Jan 1, 2013

By Robert E. Thurmond

With modern exploration techniques, it seems likely that an increasing number of the orebodies to be found in the future will be under alluvial fans or valley fill. As a result, a larger proportion of open pit mines will be confronted with the necessity for removal of substantial quantities of alluvial overburden; whereas in the past, for the most part, the open pit mine operator has dealt mainly with hard rock. If this proves to be the case, methods, equipment, and costs for alluvium stripping will become an increasingly important factor in open pit mine planning. Several operations are now faced with this situation, and various methods and equipment are used. At Pima Mining Company's operation the stripping ratio is in the range of 6/1 Well over half of the stripping volume is alluvium. The alluvium is removed almost entirely by carryalls hauling direct to a waste dump. Some removal has been accomplished by shovel and truck operation; more will be done by this means in the future. At American Smelting and Refining Company's neighboring .Mission Mine, nearly all alluvium removal is by large shovels and, trucks. U. S. Borax's Boron operation is accomplishing alluvium removal with carryalls but has been investigating other methods and equipment. The various operations in the Gas Hills Uranium District in Wyoming are stripping mainly with carryalls, although some small draglines are employed. The M. A. Hanna Company in the Mesabi Range employs large draglines and conveyor systems for removal of glacial fill. Nchanga Consolidated Copper Mines in Northern Rhodesia strips overburden with a large excavating wheel and conveyor system. There are no doubt other open pit operations with which the writer is not familiar, that are handling large quantities of alluvial overburden.

Jan 1, 1963

By J. M. Dean, R. L. Grayson

Introduction With the continued downward pressure on coal selling prices, mine management must make its operations as efficient as possible. The problem is the same one throughout the mineral industries, streamlining operations to maintain competitive min¬ing costs (Born, 1991). There has been a great deal of research into better using production manpower. But the story is different for operations support personnel. Traditionally, planning man¬power requirements are done annually, with modifications to the operating plan occurring generally quarterly. On the other hand, the demands on manpower are often dynamic, being responsive to changing productivity levels, mine conditions (including water influx, bad roof, poor floor) and unanticipated project requirements (responses to machine breakdowns or a new section setup requirement because of a drop in coal quality in another area). Such changes may impact the manpower structure significantly. At times they may cause serious labor relations problems concurrently. Realignments and the generation of instability in the workforce because of active job switching (bidding) are a result. Most responses by coal operators are reactive rather than proactive, a situation that could be mollified by more accu¬rate and detailed planning of predictable manpower require¬ments. A manpower planning tool is needed that takes into consideration such things as changing productivity levels and conditions as manhour requirements for different work areas are planned, rather than blindly allocated through traditional staffing modes. Mine Management Support System The Mine Management Support System (MMSS) is an integrated decision support system that was developed using Sun Microsystems hardware according to the contract be¬tween the US Bureau of Mines and West Virginia University. The software used in the development of MMSS included X¬ windows (Scheitler and Gettys, 1986) for the user interfaces, LASER (Raman, 1985; Hayhurst, 1990) for the expert sys¬tem and graphics components, and the C language for general programming requirements. Sun DOS was used to allow the use of IBM-compatible applications software on the Sun networks. Sun OS is the operating system. It can be viewed as an enhanced version of UNIX. One of the components of MMSS that was developed to address the many specific objectives outlined in Grayson et al. (1990) is the work scheduling system. MMSS accom¬plishes work scheduling by using a mathematical (goal) programming approach to minimize the amount of switching of workers from their regular jobs to perform other jobs (Grayson and Nutter, 1991). Manpower support program The main objective of MANSUPP is to plan a detailed manpower structure for a mine by incorporating a production schedule, condition-modified work standards and manage¬ment preferences to predict required manhours for various support activities, for example, belt moves. This is accom¬plished by gathering and processing planning information the same way a mine planner would. The program is menu¬driven with the selection of a particular menu item locating the user in the appropriate area within the spreadsheet to review/add information. All of the interactions between productivity, section conditions and management prefer¬ences and their effect on the amount of support work required must be considered. Information regarding the productivity of a particular section, the geometry of the section, work standards for individual activities and section conditions must all be gath¬ered for input into the program. In the initial stages of development, it was decided that the program be developed in an environment that mine planners were familiar with in order to accommodate the use of the program. Lotus 1-2-3 or a compatible (Quattro Pro) met this environmental need. Other reasons included ease of calculation due to built-in functions, powerful command language and macro capabili¬ties. Each of the major components of the program defined are summarized. Production schedule This area allows the user to input a production schedule for the entire mine over 12 periods. Space has been provided for five sections, advance or retreat, and two longwall sections. There are several calculations occurring in this area that do not apply to the determination of manpower, but serve as an aid in production planning. Section description The section description area of the spreadsheet is shown in Table 1. The first three items are calculated in the production schedule area of the worksheet and then transferred to this location. The remaining information is input by the user to be used in later calculations.

Jan 1, 1996

By Harold F. Yde

Hydraulic tailings fill in the Butte deep level mines was based upon studies made in 1958 by the Anaconda Company Mining Research Department, which published Bulletin No. 35, entitled "Hydraulic Stope Filling". Since then, many things have changed. At the time of the Research Departments study, dry mine tailings were hauled by rail cars from the Anaconda tailings ponds, twenty-five miles distant, to the underground mines' tailings fill plants at the Leonard Anselmo, and Mt. Con Mines. Now, with the installation of the new Weed Concentrator in Butte, tailings is delivered by pipeline to a cyclone at the Kelley Shaft, and stope filling has become more highly automated and streamlined. Presently, mill tailings at approximately thirty percent solids by weight, is pumped from the concentrator, eight thousand feet horizontally and upward, to the Kelley Fill Plant, where they are dewatered and deslimed by three Krebs Model D20B Cyclones, which discharge the material into the cased and grouted mine delivery bore holes at desired densities up to seventy percent solids. The vertical boreholes and four-inch rubber lined Victaulic pipe carry the material downward to horizontal distribution lines, which in turn tap into the stops-filling, three inch, unlined steel Victaulic pipelines. The slurry may travel several thousand feet before it finally discharges into the stope, where it lends support to the mined-out area.

Jan 1, 1969

By S. J. Lefond

Most people, when Borates are mentioned, mentally visualize the famous twenty mule team (really eighteen mules and two horses), trudging across the Mojave Desert or "she burns green Rosie, we are rich." Actually, however, the first use of borax was prior to Babylonian times. Their emissaries had orders to bring borax Iron the Gobi desert for use as a flux by the Babylonian goldsmiths. The borate mineral imported for this is not known but probably was borax. The ancient Persians and Arabians knew about borax and the Arabic word "Baurach" appears in a two thousand year old manuscript. The Sanscrit word for borax was tincana which has been corrupted to tincal. The Chinese were using borax as a glaze in three-hundred B.C. Marco Polo brought the first borax, along with gunpowder and spaghetti, from Mongolia to Europe in the late 1300's. Borax from Tibet was imported to Europe for nearly 500 years. In 1772 boric acid (sassolite) was discovered around Tuscany, Italy as a precipitant from volcanic steam vents. Production of boric acid started there about 1815 and provided the sole competition to the borax from Tibet. Borate deposits in Turkey have been known and exploited on a small scale since the 13th century. It is only recently that the operations are being modernized and production increased. About 1836, borax minerals were found in Chile and Argentina with borax production starting in 1852 in Chile and in Argentina in 1886. During the latter half of the 19th Century, Chile was the principle world producer of borax.

Jan 1, 1980

By Alan J. Solomon

The function of advertising is communication. Viewing the advertisements of mineral suppliers exposes the reader to a broad spectrum of purposes: announcements of new products, availability and supply, departmental services, company image, etc. It is the advertiser's hope that the message being conveyed is the same message being perceived by the viewer. To maximize this probability, the advertiser at least must carefully construct precise copy, identify the target audience and select the appropriate advertising medium. A truly successful and efficient ad, however, also must accurately reflect a product's life cycle, i.e., the rise and fall in demand for a product. Buggy whips and radio tubes are classic examples of items formerly in high demand. Industrial minerals are similarly affected by occurrences of product life cycles.

Jan 1, 1983

By J. C. Potvin

Although the occurrence of deposits of titanium minerals on Kenya’s present day beaches and adjacent dune systems has been well documented, the potential for older formations to host economically viable deposits had not been recognised until recently. The Magarini sands formation in Kenya has been found to contain deposits of ilmenite, rutile and zircon in quantities and grades that have the potential to be commercially exploited. Since 1995, Tiomin Resources Inc. has explored these deposits and has identified one deposit, the Kwale project, as being able to support the development of a mine producing some 300,000 tpa ilmenite, 75,000 tpa rutile and 37,000 tpa zircon. Tiomin plans to start production by late 2002. Construction of a US$137 million operation is set to commence in the first half of 2001.

Jan 1, 2001

By W. F. Mullen

Within the scope of this discussion, artificial dimension stone is defined as any manufactured product used as a substitute for natural dimension stone. The history of the development of these substitute materials is reviewed briefly, representative characteristics of each product are listed, several analyses of their market position are presented, and suggestions are made for recapturing markets lost to these products and preventing additional inroads.

Jan 1, 1959

By A. Anani, K. Awuah-Offei

"Accounting for changing duty cycles in equipment matching maximizes equipment utilization and productivity. The objective of this study is to investigate if the optimal number of shuttle cars for a particular panel width is optimal in different segments of the panel. In this study, discrete event simulation (DES) is used to determine the optimal number of cars that maximizes productivity in each segment. Data from a real-life mine is used to validate the model. The study shows that the optimal number of cars for the entire panel may not be optimal for some of the defined segments. INTRODUCTION Fleet optimization is important for efficient mine management. Deploying the optimal fleet minimizes the capital and operating expenditure for particular operating conditions and production targets. In an operating mine, with an already existing fleet, deploying the optimal fleet maximizes productivity or minimizes production cost with the available resources. Hence, a lot of research has focused on how to determine the optimal fleet size for a mining operation, given particular operating conditions. Mine managers and engineers have successfully used discrete event simulation (DES) to determine the optimal fleet size in mines (Michalakopoulos, Roumpos, Galetakis, & Panagiotou, 2015; Awuah-Offei, Osei, & Askari-Nasab, 2011; Ben-Awuah, Kalantari, Pourrahimian, & Askari-Nasab, 2010; Govinda Raj, Vardhan, & Rao, 2009; Yuriy & Vayenas, 2008; Kwame Awuah-Offei, Temeng, & Al-Hassan, 2003). In most cases, the published work on this topic involves determining the number of hauling units to be matched to a loading unit. Many of these examples involve truck-shovel optimization. There are, however, some underground mining examples. For instance, we recently concluded work that involves fleet optimization in underground room and pillar (R&P) coal mining (Awuah-Offei & Anani, 2015). Generally, when DES is used in fleet optimization it involves three steps: (1) Build a valid model of the mining system capable of predicting the required outputs with varying fleet composition; (2) Design and conduct experiments that vary the fleet composition across all feasible options; and (3) Determine the optimal fleet based on the results of the simulation experiments. A major decision in the first step is which outputs should be modeled. Some examples in the literature include productivity, unit cost, loader utilization, queue length, and hauler waiting times (Awuah-Offei et al., 2011; Govinda Raj et al., 2009; Kwame Awuah-Offei et al., 2003). Often, more than one of these outputs are simulated and considered as the objective function of the optimization."

Jan 1, 2016

By Thomas Gleason

Wet scrubbing of fine coal from Thermal dryers poses a number of problems in adapting the gas cleaning equipment for required clean-up of the fine particulate matter. Among then are: 1. The dust In the gases leaving the Thermal dryer cyclone-s is often extremely fine with high percentages of the total dust loading less than one (1) micron in size. 2, The flue gas entering the scrubber is corrosive since the coal fired in the thermal dryer furnace is in the range of 0.7% by weight sulphur or higher. Therefore comparatively high cost stainless steel alloys or corrosion resistant linings are required for a satisfactory service life. 3. Requirements for residual coal loadings leaving the gas e scrubber are continually being lowered while modern coal preparation operation is imposing heavier burdens on the collection system through introduction into the Thermal dryer system of very fine coal previously not recovered. The advent of flotation systems in increasing numbers is typical of this trend 4. The installation of a scrubbing system on Thermal dryers is made primarily to reduce air pollution and product recovery value is of little or no value. Therefore the operating costs, that is, of gas pressure drop and water requirements must be held to a minimum.

Jan 1, 1962

By Michael J. Feltes

In mining operations, conveyors hold one of the most important keys to productivity. Sudden belt or belt-splice failures and extended repair downtimes can contribute to low material-handling system availability. Consequently, operations and maintenance personnel should have a thorough understanding of the available splicing and repair alternatives and how each method can affect the productivity and cost-effectiveness of their operation. The two primary methods of joining belt ends - vulcanization and mechanical fastening - affect the likelihood of sudden failure and repair times in different ways. The time-honored method of vulcanization remains popular in many conveyor-intensive underground and above-ground mining operations around the world. At first, vulcanization may seem attractive because, when done properly by trained and experienced craftsmen, it can match the original belting fairly closely and give the splice a smooth, continuous surface with no edges or seams to invite snagging.

Jan 1, 1993

By Xuchen Fan, Chenyang Zhou, Yuemin Zhao, Liang Dong, Chenlong Duan

A gas–solid fluidized bed using magnetite particles is an effective methodology for coal beneficiation in the field of dry coal cleaning. Broadening the size range of magnetite used in the bed decreases medium preparation cost. In this study, a tapered fluidized bed was used to investigate a magnetite particle size range of −0.5 + 0.074 mm. The results showed that a tapered fluidized bed effectively strengthens mixing of magnetite with a wide size range (−0.5 + 0.074 mm). The results of beneficiation experiments indicated that with increasing tapered angle, separation efficiency increased and then decreased. The highest separation efficiency was obtained at a tapered angle of 10°. The optimal results showed that the ash content of the concentrate decreased from 31.82% to 12.33% with a probable error of 0.11, which indicated that a tapered fluidized bed was efficient to improve fine coal beneficiation performance.

By J. G. Jenkins

Magma Copper Co.'s San Manuel solvent extraction/electrowinning (SX-EW) facility has operated since May 1986. The original facility had a design capacity of 22.6 kt/a (25,000 stpy) of electrowon copper cathode produced by processing pregnant leach solution from an open pit-heap leach operation. In 1988, the plant was expanded to 45.3 kt/ a (50,000 stpy) to incorporate processing in-situ leach solutions. This pager focuses primarily on the heap leaching area with regard to exploration, testing, feasibility, permitting, design and construction, and operating practices. Research using surfactant leaching aids to enhance copper recovery is also discussed.

Jan 1, 1995

By Thomas A. Gwynn

"A beautiful America will require the effort of government at every level, of business, and of private groups. Above all it will require the concern and action of individual citizens, alert to danger, determined to improve the quality of their surroundings, resisting blight, demanding and building beauty for themselves and their children." "Improvement of our environment" has become a cause much like "motherhood". The increased awareness of the public concerning this subject makes it most unpopular for anyone to be involved in anything that seemingly is detrimental to our environment. And this awarement goes far beyond our biggest pollution problem in America - the distribution of paper, abandoned automobiles, beer cans and other garbage by our enlightened society along every city, highway, trout stream, river and mountain in America. In fact, the greatest awarement comes because of the "sensational" reporting and writing in our various national communication media, wherein the same voting citizens who so generously distribute their refuse about the countryside are emotionally aroused and duped into transferring what is truly a national problem onto the shoulders of a few industries - notably and particularly the mineral extraction industry. Certainly mankind is more and more stumbling over his own garbage daily, a fact that is easier to sell a citizen of one of our large cities than a resident of the wide open spaces of the west. Yet even in the Rocky Mountain states, the "Land of Sky Blue Waters", the "Big Sky Country", and particularly in Salt Lake valley smog is not unknown. Pollution and littering have become problems that need to be faced squarely. In North Dakota alone it has been estimated that one section of farm land each year flows down the mighty Missouri and the greatest producer of sediment is now reported to be the highway department.

Jan 1, 1969

By H. W. Hintze

Coal handling facilities, such as utility plants, coal terminals, ports, manufacturing, processing, etc. Protect themselves against interruptions in coal receipts by maintaining a 60 to 90 day supply in storage. Not too long ago, these storage piles were referred in terms of hundreds or thousands of tons. Today, it is not unusual to have hundreds of thousands or millions of tons in storage. Burn, or shipping and receiving, rates have increased dramatically and storage piles have grown in horizontal as well as vertical dimensions. Fixed systems for delivering and retrieving coal from storage have increased in length and operating capacity and have become highly sophisticated in their operation. With few exceptions, mobile material handling equipment is used to handle all coal beyond the reach of these systems. These machines take excess loose coal from the fixed system to the storage area, place it on the storage pile, compact it, maintain the pile, protect against spontaneous combustion, the spread of fires if they occur, and return the coal to the reclaim system as required, plus many of the small chores around the facility.

Jan 1, 1981

By Priscilla P. Nelson, Francis L. C. Fong

Introduction Fracture mechanics is the study of the behavior of cracks and their modes of propagation. During cracking, energy is consumed in creating new surface area. The more energy a material absorbs, the higher is its fracture resistance. This fracture energy is provided either by work done externally, by the release of elastic strain energy within the cracked body, or by a combination of these two effects. Fracture resistance is measured in terms of either the stress intensity factor, K, or the energy release rate (also referred to as crack driving force), G. For linearly elastic materials, these two quantities are related by the following equation: [ ] where [u] is Poisson's ratio and E is the modulus of elasticity. Both K and G are direct functions of the applied force and the crack length. The process of rock cutting with full-face tunnel boring machines (TBMs) involves the indentation of a rock surface by rolling disc tools. Excavation occurs as fractures, extending from the locus of chip indentation, propagate between concentric disc grooves and liberate rock chips from the intact rock face. Since disc cutting is achieved by a fracture process, it is logical to anticipate that differences in cuttability of a variety of rocks should be related to the variation of fracture material properties among the rocks. Such a relation has been demonstrated between the performance of full-face TBMs and the critical crack driving force for excavation in relatively high strength, brittle, low porosity, isotropic rock (Nelson et al., 1985). The objective of this paper is to report on the results of a continued investigation of the relationship between fracture material properties and the effectiveness of disc cutting. Additional reliable data on full-face TBM performance is difficult to obtain, so that the results of disc linear cutter tests performed by the Transport and Road Research Laboratory (TRRL) (U.K.) are utilized in this study. Fracture Material Property Evaluation If a crack tip is subjected to a perfectly plain strain condition, many materials will behave in a brittle manner, and the material resistance to fracture is constant during crack growth. This resistance is referred to as the plain strain fracture toughness, believed to be a material property. The standard testing procedure for this parameter is given in the American Society for Testing and Materials (ASTM) test designation E399. To ensure plain strain conditions, acceptable specimen geometries are specified. Unless these geometric specifications are adhered to, the measured fracture resistance is regarded as the apparent fracture toughness, and a subscript Q is used, as [ ]. The methodology adopted by ASTM E399 is within the framework of Linear Elastic Fracture Mechanics (LEFM). This approach assumes that material resistance against cracking is developed instantaneously, without initial stable or subcritical crack extension. Prior to crack advancement in rock, however, much of the crack driving energy is absorbed in a localized volume in front of the crack tip, referred to as the plasticity or microcracking zone. This capability for energy absorption substantially increases material resistance, and a crack may be arrested unless an increased crack driving force is applied. The LEFM or plain strain assumptions would underestimate the actual fracture resistance of such a material. Such a conservative approximation may be desirable in the design of structures against fatigue or brittle failure. In mining or tunneling, however, an underestimation of crack resistance can lead to the selection of underrated excavation equipment and a decrease in production efficiency. The development of fracture resistance in rock is best described by the material resistance curve, or R-curve, which is a plot of fracture resistance as a function of crack extension. Typically, peak resistance is only reached after a finite amount of subcritical crack growth. The

Jan 1, 1986

By Frank A. Jerabek

Problems of mine backfilling and fill material deposited underground, the characteristics and relationship between the deposited fill material and overlying ground, and the practical applications and limitations of hydraulic backfilling as ground support are discussed. A great variety of materials ranging from coal washery refuse to concentrator tailings is used as hydraulic fill. Some materials will solidify and cement; others will resemble quicksand, Hydraulic fill as ground support is more efficient in inclined mine openings than in horizontal mine openings, where it cannot be placed tightly to the back. This and other deficiencies of hydraulic backfilling led to the development of pneumatic stowing. Research work in hydraulic backfilling at the Pennsylvania State University is also discussed. This research work includes the investigation of segregation in the discharged fill slurry, the quantity of solids escaping in the drain liquid, the relationship of escaping solids to slurry concentration and discharge rate, and the compressibility of fine fill material.

Jan 1, 1965

By D. S. Dick

Over the last few years, new methods to characterize the flow properties of bulk solids have been developed. Abrasive wear and particle attrition can now be accurately measured in a laboratory and scaled up to field conditions. In addition, the effect of large particles on a material's flow properties (cohesive strength, bulk density, wall friction) can be determined as well as the effects of various additives such as Freeze Conditioning Agents. New developments have also taken place in terms of devices to improve the reliability of solids flow. Much attention has been paid to finding ways to provide a mass flow pattern with relatively shallow hopper walls through the use of inserts. Such devices can also provide reliable in-bin gravity blending of bulk solids and/or completely non-segregated discharge. Other developments have occurred in the area of belt-to-belt transfer chutes and sealing screws. Many of these developments have direct application in the mining and minerals processing industries. Examples of each will be highlighted.

Jan 1, 1988

By K. Katen

In another situation, Dave Zegeer, the Assistant Secretary of Labor for Mine Safety and Health, whom all of you know very well, would have taken the opportunity to talk with you. In his absence, however, I would like to reference some of his recent comments which may help us to see the issue of mine safety in historical perspective. Dave pointed out that this year is the eightieth anniversary of the Great Earthquake and Fire of San Francisco. The whole world heard about that disaster--it and the 452 people who died in it. In that same year, nearly five times as many people died in coal mines, but no one particularly noticed.

Jan 1, 1986

By A. K. Andersen

One of the prime examples of the versatility of the MARCONAFLO system, which is a body of technology comprising the means to handle, store, load, transport, discharge and reclaim mineral commodities in slurry form, is the direct application of this process to leaching ores. The initial approach was to provide a much improved materials handling system for the transport of copper ores; however, an extensive development program, inclusive of prototype and pilot plant tests, has established that a new leaching concept is possible with this system. Data are presented from the leaching operation of a 25 TPD pilot plant utilizing a copper-oxide ore, mainly chrysocolla. This pilot plant was designed to incorporate true countercurrent flow where the ore is actually in motion, as contrary to vat leaching operations, and the ore being successfully leached is fine crushed ore (3/8-inch x o), contrary to agitation leach circuits. Extractions in excess of 85% of the soluble values are common with only 15 hours of retention time in the MARCONAFLO leaching system.

Jan 1, 1975