Search Documents

By R. Owens, C. Roos, B. Hill, S. Rosenthal

It is common practice, and even legally required in many jurisdictions, to design two-lane haul roads in open pit mines to three and a half times the widest dimension of the haul trucks operating on the road. In open pit gold mines with high strip ratios, the road width has a significant impact on the economics of a design. It is possible to minimize the flattening of the highwall if the road width is reduced, assuming the width used is not needed to flatten the slopes for geotechnical purposes. With the use of autonomous haulage and pullouts, it may be possible to operate safely and efficiently on a reduced road width of two times the width of the hauling equipment.

Mar 2, 2022

By Douglas J. Lootens

Geologic mapping was undertaken in the Sierrita Mountains as part of a Doctoral program at the University of Arizona, Tucson. During the study, approximately 35 square miles was mapped in detail, with particular attention given to specific areas of great or significant structural complexity and their relation to mineralization in the vicinity. A combination, of field studies and photogeologic interpretation was used in order to define regional and local structural controls for disseminated copper-molybdenum mineralization in and adjacent to the study area. Gratitude is expressed to the faculty of the University of Arizona, Department of Geology for their assistance in this work and to Bear Creek Mining Company for making numerous reports and drill cores available for study.

Jan 1, 1965

By J. R. Walls

Mining is one of world's oldest industries. Its rich history continues into modern times. The Waste Isolation Pilot Plant (WIPP) located in southeastern New Mexico is writing the next chapter in mining history. In fact, WIPP technology is the key to closure of the nuclear cycle with the disposal of nuclear waste in a deep geological repository. It might seem odd that the age-old institution of mining would be linked to the problem of nuclear waste disposal. In fact, the nuclear industry would not exist without mining. Uranium ore is mined from either underground or surface mines as the initial step in harnessing the magnificent resource of nuclear energy.

Jan 1, 1996

By M. K. Larson, R. G. Wade

Researchers at the National Institute for Occupational Safety and Health (NIOSH) are studying the time-dependent response of rock stressed along weakness planes. The objective is to improve mine safety by reducing the number of roof falls that cause injuries and fatalities to miners. Researchers conducted direct-shear tests on mud-stoneovercored from a coal mine roof. Results showed frictional strength weakens with displacement along the shearing planes. Results of direct-shear creep tests also showed time-dependent deformation. Test measurements were compared to classical analytical models. Results suggest that risk of roof collapse may be decreased through layout and support design to reduce creep rates and thus slow progression toward failure.

Jan 1, 2000

By A. F. Ogg

The installed world steel capacity remains 20% above the present world steel demand. Energy costs have risen enormously in recent years, as illustrated in Figures 1 and 2. The role of the sinter plant is becoming more exacting as it becomes vital to minimize energy consumption. Continuous grate sintering, although pioneered in the United States, has always been the second grade burden preparation route, due to the predominance of easily up- graded ores which were more readily agglomerated by pelletizing. To achieve blast furnace performance up to best world standards, sinter of consistent high quality must be produced with virtually no atmospheric pollution. The plants must be capable of achieving this demanding level of quality whilst utilizing high proportions of revert materials, iron ore concentrates and fluxes . However, with the present difficult economic climate in the iron and steel industry, the economic production of sinter and ultimately steel is becoming increasingly important. The iron and steel industry is looking closely at costs and is identifying the need for sinter plants that will cope with a wide range of sintering materials to give the cheapest blend at varying output levels dependent upon demand. In order to meet these requirements, sinter plant builders are designing plants with particular attention on flexibility.

Jan 1, 1980

By G. C. Kachel

Significant effort has been expended and considerable success has been realized m the application of instrumentation and automatic control equipment in the mining and ore processing industries. This effort has been applied principally to process equipment with the objective of increasing throughput, minimizing labor requirements and/or improving grade or product quality. Less spectacular, but quite rewarding has been the successful application of instrumentation and automatic control equipment to a wide variety of material handling equipments. This paper describes some of this work including: (1) automatic weighment of load-haul-dump units and trams underground; (2) automation of skip loading; (3) instrumentation applied in feeders and conveyors; (4) level measurement in bins, silos, vessels and sumps; (5) automatic blending of sized materials; (6) automatic loading of ships, trains and trucks; (7) automatic control of tailings disposal facilities

Jan 1, 1973

By L. K. Bandyopadhyay, P. K. Mishra, S. K. Chaulya, R. S. Singh, A. Kumar, N. Tripathi, K. Mandal

A comprehensive field study has been carried out to measure the background air quality status and identify the air pollution sources from opencast mines around a heritage site in India. Air quality modeling has been carried out to envisage dust concentration due to the existing and closed mines in the region. The predicted total PM10 and PM2.5 levels at the selected receptor locations ranged from 86.39 to 194.89 and from 34.82 to 99.55 µg/m³, respectively.

Jan 12, 2022

By S. E. Chetlin

In the mid-1970?s, the market value of tangible assets of S&P 500 companies far outstripped the value of intangible assets, including intellectual property (e.g., 83% tangible assets v. 17% intangible assets).1 By 2005, the picture was quite different. By that time and continuing to 2010, S&P 500 companies? market value of intangibles was about 80%, with tangible assets accounting for only 16% of market value.2 This swing highlights the importance in today?s world of understanding intellectual property rights and varying strategies and options for protecting them. This paper discusses intellectual property rights particularly patents and trade secrets, specifically: 1) types of intellectual property; 2) choosing the mode of intellectual property protection; 3) obtaining patent protection; and 4) using patents as a sword versus a shield.

Jan 1, 2012

A brief description of the mining method and ventilation system of the San Manuel Mine?s first presented; this is necessary to an understanding of the heat problem and cooling system. The problem of heat at San Manuel is discussed. Charts and graphs showing the relationships between ambient surface air and underground temperature conditions are given. A history of attempts to cool air at San Manuel is presented, starting with the first refrigeration type air coolers which were used in development headings, and followed by the underground water chillers that were used in conjunction with cooling coils. Goals for design of a centralized cooling system with ultimate heat rejection through surface cooling towers are presented. The problems found with using the centralized system in main cooling coils are discussed. Plans for modification of the centralized system as utilized is the summer of 1987 are given, along with results obtained and problems with the system. Plans for subsequent modifications are presented.

Jan 1, 1988

By Steven M. Bishoff

The reclamation of surface land areas disturbed during the course of coal recovery became a major, universal consideration upon the implementation of the Surface Mining Control and Reclamation Act of 1977. This legislation not only established reclamation as an absolute requirement, but also presented guidelines for reclamation standards and required bond-posting procedures to assure completion of the reclamation process. The Office of Surface Mining was established to enforce the provisions of the Congressional mandate by promulgating specifically detailed regulations and supervising the State participation in this regulatory process. The major operational consequences of the reclamation-related provisions of the Act and the OSM regulations are the increased costs and complex procedures necessary to accommodate the regulatory authorities. It is anticipated that many of these costs and procedures have not been adequately evaluated by either the coal operators or the regulatory bodies. It is, therefore, necessary to proceed with an examination of the general reclamation processes, the effect of these processes on product costs, and the methods, if any, which may be utilized to minimize their impact on the overall operation.

Jan 1, 1981

By Wm. I. Weisman

Sometimes in assessing where we are and where we are going it is informative to take a look at where we have been. Whether or not it adds to our understanding of the present, I think it may be interesting to review some of the past history of our industry. As a starting point I chose to use the famous Paley Commission Report, formally known as "The U. S. President's materials Policy Commission -Resources for Freedom."(l) The Paley Commission report said "Fluorspar is an essential raw material for the steel, aluminum, and chemical industries." Of course this statement is still true. It also said, "United States known reserves of fluorspar would be sufficient for some 15 years at present rates of consumption--about 426 000 short tons in 1960. Projected consumption for 1975, however, is several times as great, and reserves in other free countries do not appear adequate to supply United States deficiencies during the next 25 years." This simply demonstrates how even the most learned and competent people can observe all the facts avail-able to them at a given time and yet be unable to predict the future very accurately. We all know that reserves in other countries are more than adequate to supply the United States today, 25 years since the report was published. In fact, the report estimated free-world reserves at something over 36 million tonnes (40 million short tons). Contrast this with 246 million tonnes (271 million short tons) estimated as total world reserves from the section on fluorspar from Commodity Data Summaries of 1974, published by the Department of the Interior. (2) The Paley Report discusses other matters pertaining to fluorspar that are still of interest, such as improving mining methods. Furthermore, it certainly did a good forecasting job in noting that greater recycling should become possible in the aluminum industry in regard to fluorine lost in wastes and also concerning the substitution of fluorspar in the steel industry by other fluxing materials. It also suggested that non-fluorine containing propellants should be investigated as a replacement of those containing fluorine as a conservation matter. Some discussion was devoted to recovering the fluorine content of phosphate rock, which is being practiced today, but was in its infancy in 1950.

Jan 1, 1978

By Harry Leslie Bullock

With silica making up more than 27% of the earth's crust, its oxides amounting to more than 59% of the igneous rocks and quartz the most prevalent of the main free oxides, it follows that the mining engineer' is in constant contact with quartz, mainly as a gangue material to be removed as completely and economically as possible and sometimes as a valuable mineral to be purified' for the chemical,, ceramic or glass industries. Water scarcity under desert or semi-arid conditions, dwindling water supplies and difficulties of wet waste disposal in many locations and trouble from freezing in arctic locations make dry benefication more and more desirable. Advances made during the last few years in apparatus and methods and a steadily increasing knowledge of solid state physics are widening the field open to the economical application of electrostatic separation.

Jan 1, 1967

By Thomas W. Turk

The water treatment industry has historically been involved with reducing or inhibiting the inherant scale forming or fouling tendencies of natural waters associated with large industrial cooling water systems. Fouling is an extremely complex phenomenon. From a fundamental point of view, it may be characterized as a combined momentum, heat, and mass transfer problem. Chemical reaction kinetics is involved, as well as the solubility characteristics of salts in water and corrosion technology. It is a routine practice to over size pumps, piping and heat exchangers to compensate for fouling.

Jan 1, 1983

By Gerald H. Luttrell

The determination of mass balances is the first step in analyzing the performance of processing circuits. Although conceptually very simple, the mathematics associated with mass balances can be cumbersome when conflicting data sets and/or complex circuits are evaluated. Fortunately, many of the spreadsheet programs available today include powerful search routines which can be adapted to solve common mass balance problems. To demonstrate these capabilities, a generalized mass balance program has been developed using the Microsoft Excel? spreadsheet. Compared to commercial programs, the spreadsheet format is user-friendly, more versatile and easier to customize. This paper reviews the mass balance problem and describes how spreadsheet tools can be used to reconcile conflicting data.

Jan 1, 1996

By Mark P. Walsh

In recent years in situ leach mining has emerged as a viable technology for the recovery of uranium from strata in South Texas which contain relatively low concentrations of uranium ore. Because the ore bodies lie within groundwater aquifers, a significant determinant in the economics is the requirement that such aquifers be protected from contaminantion. Since ammonia is one of the constituents of the leach solutions now being field tested, one environ- mental problem to be resolved is the removal of ammonia at the end of mining. A second related question is the fate of the ammonia which is not removed by the restoration procedure. This paper considers the displacement and migration of ammonium in a flowing electrolyte with concomitant ion exchange. The ion exchange is an important feature since, during the solution mining phase, ammonium saturates the mineral exchange sites and must be removed from these sites. A mathematical model is used to simulate this process and the model is tested against the results of laboratory experiments. It is found that the simulations are adequate if an appropriate selection of parameters is made. The model is then used to investigate the effect of cation composition and concentration of the restoration medium as well as dispersion on the overall effectiveness of the process. It is concluded that increasing the concentration of monovalent ions in a solution containing a mixture of both monovalent and divalent ions decreases the adsorption selectivity of the divalent ions with respect to all monovalent ions including ammonium. Thus increasing the ionic concentration of a restoration fluid by increasing the concentration of a nonselectively adsorbed (with respect to ammonium) ion may have a very limited benefit. Dispersion attending the flow of fluids in a porous medium is also shown to be an important factor. The effect of dispersion can greatly reduce the benefits of having a displacing cation which is adsorbed selectively with respect to ammonium. Since dispersion increases almost linearly with fluid velocity, an optimum displacement rate may exist.

Jan 1, 1979

By Omar A. Muhtadi, R. Bruce Thorndycraft, David A. Milligan

9.1 INTRODUCTION Precious metals in a leach solution are extracted, concentrated, and purified to complete the process begun in the heap and to produce an end product which will provide an economic payback to the mine developer/operator. Several different processes are required to convert the dissolved precious metals into pure metal bars. This chapter discusses the actual production of metal once it has been recovered from the pregnant leach solutions by the zinc cementation (Merrill -Crowe) or carbon adsorption processes. Metal production is generally taken to mean the production of a fairly pure "dore" bar. This chapter also reiterates some information from Chapter 8 in a slightly different context, since the focus of Chapter 8 was a fairly detailed description of the two actual recovery processes, whereas the focus of this chapter is metal production. The sale of an intermediate precious metal product is possible (as opposed to the production of dore bars at the mine site); however, the value of the precious metals is reduced by the various charges and risks associated with precious metal processing. For this reason, most operators choose to produce the most refined metal possible in order to maximize project economics. Precious metals may be extracted from the leach solution by both conventional and unconventional processes. The conventional processes are activated carbon/electrowinning (ACE) and zinc precipitation (ZIP). The unconventional processes are resin ion exchange, solvent extraction, and direct electrowinning. A typical ACE process has two circulating loops. The first loop adsorbs the cyanide-metal complexes from the dilute leach solution onto the activated carbon. A second, separate solution loop removes the cyanide-metal complexes from the activated carbon into a strong solution, the electrowinning electrolyte. Activated carbon is transferred from one fluid loop to the other. The operating cost of the ACE process is directly proportional to the quantity of carbon stripped and thus to the quantity of precious metal produced. A typical ZIP process contains a single circulating loop. The solution is filtered, deaerated, contacted with zinc, and filtered again. The barren leach solution is then returned to the heap. The zinc sludge recovered in the

Jan 1, 1988

By C. D. Anderson

A variety of processing technologies exist for recovery from both primary and secondary sources of rhenium. Currently, there are no known primary rhenium deposits; thus, the method in which primary rhenium is produced is dependent on the commodity of which it is a byproduct, e.g., copper, molybdenum, uranium, etc. In addition, focus on the recovery of rhenium from secondary sources, such as alloy scraps and catalysts, is continually growing. This paper presents a review of both primary and secondary processing technologies for the recovery of rhenium.

By P. Walshe

A common belief among Itlnl.ng operators today is that computer based truck m:mitoring and dispatching systems are only applicable to, or affordable by, very large scale open pit mines. Before the advent of microcomputer technology this belief was generally a valid one. Microcomputer technology as it currently exists has reached a high level of sophistication and capability, rapidly approaching that of the minicomputer standard. When coupled with reliable software and data communications packages, it now provides the means to make truck monitoring and dispatching a viable and attractive management aid to mines of all sizes. This paper briefly addresses the evolution and current state of computer truck dispatching and examines a microcomputer based system in this context. To demonstrate the effectiveness of this approach to truck dispatching a recent installation in a medium sized mine is presented. Preliminary field data from the case mine are presented to illustrate the methodology.

Jan 1, 1989

By B. Mirabile, B. Stables

Standing support is often used in conjunction with underground retreat mining. Knowledge of the load-displacement behavior of a standing support, and loading induced by the mine opening is critical to proper support selection. The NIOSH STOP database contains load-displacement laboratory test data for most commonly used standing supports. Hydraulic load cells currently used to measure in-situ loading of standing supports have exhibited leakage under load, producing irregularities within the dataset. An improved hydraulic load cell eliminates leakage and produces more consistent data. INTRODUCTION A hydraulic load cell, more commonly known by “flat jack” or JackPack, is a device installed to determine the loading characteristics of roof to floor supports. These standing or roof to floor supports include, but are not limited to: pumpable cribs, cans, wooden cribs (4-point, 9-point, etc.), metal props, wood timbers, concrete donut cribs, and other variations of these standing supports. Flat jack devices have been used previously to determine the loading of such roof to floor supports. The most commonly used load cell for standing supports is based on a design intended for pre-stressing standing supports, not load measurement. These load cells are produced in South Africa, and can be formed into several different shapes depending on the applications (Barczak). Flat Jacks are manufactured in various shapes and sizes depending on the application, common shapes are square and round that are 25.4 mm (1.0 inch) thick when collapsed as shown in Figure 1. The sheet metal that makes up the bladder is comprised of 19 gauge or 1.11125 mm (0.04375 inch) thickness, the top and bottom pieces of sheet metal are resistance seam welded around the perimeter. There are two different ports installed on one of the bladder skin corners of the flat jacks; these ports allow a fluid to fill the unit and the other port has a relief valve. The fill port is comprised of a check valve. The pressure relief valve is located in the second port; preset to 1724 kPa (250 psi), pressure relief valve will keep the load cell from bursting. Bursting of these load cells typically causes a small tear in the metal skin allowing the fluid to leak out without a large catastrophic failure. The effective inflation range of these load cells is between 25.4 mm (1.0 inch) to 254.0 mm (10.0 inches) thick. Different types of fluids can inflate these load cells but the most common and easily accessible fluid for testing applications is water. Water pressure from the mine supply line can inflate these load cells to the desired load. Depending on the pre-stressing requirements a pneumatic powered pump, hydraulic pump or hand pump may be required to inflate the load cells.

Jan 1, 2019

By John A. Riddle

Some of the pitfalls and problems in selecting and applying corrosion-resistant materials in uranium plants are discussed, together with some suggested solutions. Includes some cost data.

Jan 1, 1979